+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- */
-
-#include <common.h>
-#include <init.h>
-#include <asm/global_data.h>
-#include <asm/io.h>
-#include <asm/arch/at91sam9x5_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
-#include <asm/arch/at91_common.h>
-#include <asm/arch/at91_rstc.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/gpio.h>
-#include <net.h>
-#include <netdev.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* ------------------------------------------------------------------------- */
-/*
- * Miscelaneous platform dependent initialisations
- */
-static void wb45n_nand_hw_init(void)
-{
- struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
- struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
- unsigned long csa;
-
- csa = readl(&matrix->ebicsa);
- /* Enable CS3 */
- csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
- /* NAND flash on D0 */
- csa &= ~AT91_MATRIX_NFD0_ON_D16;
- writel(csa, &matrix->ebicsa);
-
- /* Configure SMC CS3 for NAND/SmartMedia */
- writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
- AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
- &smc->cs[3].setup);
- writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) |
- AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(6),
- &smc->cs[3].pulse);
- writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(6),
- &smc->cs[3].cycle);
- writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
- AT91_SMC_MODE_EXNW_DISABLE |
- AT91_SMC_MODE_DBW_8 |
- AT91_SMC_MODE_TDF_CYCLE(1), &smc->cs[3].mode);
-
- at91_periph_clk_enable(ATMEL_ID_PIOCD);
-
- /* Configure RDY/BSY */
- at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
- /* Enable NandFlash */
- at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
- /* Disable Flash Write Protect Line */
- at91_set_gpio_output(AT91_PIN_PD10, 1);
-
- at91_set_a_periph(AT91_PIO_PORTD, 0, 1); /* NAND OE */
- at91_set_a_periph(AT91_PIO_PORTD, 1, 1); /* NAND WE */
- at91_set_a_periph(AT91_PIO_PORTD, 2, 1); /* NAND ALE */
- at91_set_a_periph(AT91_PIO_PORTD, 3, 1); /* NAND CLE */
-}
-
-static void wb45n_gpio_hw_init(void)
-{
-
- /* Configure wifi gpio CHIP_PWD_L */
- at91_set_gpio_output(AT91_PIN_PA28, 0);
-
- /* Setup USB pins */
- at91_set_gpio_input(AT91_PIN_PB11, 0);
- at91_set_gpio_output(AT91_PIN_PB12, 0);
-
- /* IRQ pin, pullup, deglitch */
- at91_set_gpio_input(AT91_PIN_PB18, 1);
- at91_set_gpio_deglitch(AT91_PIN_PB18, 1);
-}
-
-int board_eth_init(struct bd_info *bis)
-{
- int rc = 0;
-
- if (has_emac0())
- rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00);
-
- return rc;
-}
-
-int board_early_init_f(void)
-{
- at91_seriald_hw_init();
- return 0;
-}
-
-int board_init(void)
-{
- /* address of boot parameters */
- gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-
- wb45n_gpio_hw_init();
-
- wb45n_nand_hw_init();
-
- at91_macb_hw_init();
-
- return 0;
-}
-
-int dram_init(void)
-{
- gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
- CONFIG_SYS_SDRAM_SIZE);
- return 0;
-}
-
-#if defined(CONFIG_SPL_BUILD)
-#include <spl.h>
-#include <nand.h>
-
-void at91_spl_board_init(void)
-{
- /* Setup GPIO first */
- wb45n_gpio_hw_init();
-
- /* Bring up NAND */
- wb45n_nand_hw_init();
-}
-
-void matrix_init(void)
-{
- struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
- unsigned long csa;
-
- csa = readl(&matrix->ebicsa);
- /* Pull ups on D0 - D16 */
- csa &= ~AT91_MATRIX_EBI_DBPU_OFF;
- csa |= AT91_MATRIX_EBI_DBPD_OFF;
- /* Normal drive strength */
- csa |= AT91_MATRIX_EBI_EBI_IOSR_NORMAL;
- /* Multi-port off */
- csa &= ~AT91_MATRIX_MP_ON;
- writel(csa, &matrix->ebicsa);
-}
-
-#include <asm/arch/atmel_mpddrc.h>
-static void ddr2_conf(struct atmel_mpddrc_config *ddr2)
-{
- ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_LPDDR_SDRAM);
-
- ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
- ATMEL_MPDDRC_CR_NR_ROW_13 |
- ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
- ATMEL_MPDDRC_CR_DECOD_INTERLEAVED |
- ATMEL_MPDDRC_CR_DQMS_SHARED);
-
- ddr2->rtr = 0x411;
-
- ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |
- 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |
- 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET |
- 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET |
- 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET |
- 2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET |
- 2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET |
- 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);
-
- ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET |
- 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
- 19 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
- 18 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
-
- ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET |
- 2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
- 3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
- 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
- 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
-}
-
-void mem_init(void)
-{
- struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
- struct atmel_mpddrc_config ddr2;
- unsigned long csa;
-
- ddr2_conf(&ddr2);
-
- /* enable DDR2 clock */
- at91_system_clk_enable(AT91_PMC_DDR);
-
- /* Chip select 1 is for DDR2/SDRAM */
- csa = readl(&matrix->ebicsa);
- csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
- writel(csa, &matrix->ebicsa);
-
- /* DDRAM2 Controller initialize */
- ddr2_init(ATMEL_BASE_DDRSDRC, ATMEL_BASE_CS1, &ddr2);
-}
-#endif
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_SYS_THUMB_BUILD=y
-CONFIG_ARCH_AT91=y
-CONFIG_SYS_TEXT_BASE=0x23f00000
-CONFIG_TARGET_WB45N=y
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_SYS_MEMTEST_START=0x20000000
-CONFIG_SYS_MEMTEST_END=0x23e00000
-CONFIG_ENV_OFFSET=0xA0000
-CONFIG_SPL_TEXT_BASE=0x300000
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_ENV_OFFSET_REDUND=0xC0000
-CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9X5,SYS_USE_NANDFLASH"
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk rw noinitrd mem=64M rootfstype=ubifs root=ubi0:rootfs ubi.mtd=6"
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_SPL_NAND_DRIVERS=y
-CONFIG_SPL_NAND_BASE=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_MEMTEST=y
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_LOADS is not set
-CONFIG_CMD_NAND=y
-CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_AT91_GPIO=y
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-# CONFIG_SYS_NAND_USE_FLASH_BBT is not set
-CONFIG_NAND_ATMEL=y
-CONFIG_PMECC_CAP=4
-CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER=y
-CONFIG_ATMEL_USART=y
-CONFIG_LZMA=y
-CONFIG_LZO=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Configuation settings for the WB45N CPU Module.
- */
-
-#ifndef __CONFIG_H__
-#define __CONFIG_H__
-
-#include <asm/hardware.h>
-#include <linux/stringify.h>
-
-/* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
-#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
-/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-
-/* serial console */
-#define CONFIG_USART_BASE ATMEL_BASE_DBGU
-#define CONFIG_USART_ID ATMEL_ID_SYS
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/* SDRAM */
-#define CONFIG_SYS_SDRAM_BASE 0x20000000
-#define CONFIG_SYS_SDRAM_SIZE 0x04000000 /* 64 MB */
-
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
-
-/* NAND flash */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x40000000
-/* our ALE is AD21 */
-#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
-/* our CLE is AD22 */
-#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
-#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD4
-#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PD5
-
-#define CONFIG_RBTREE
-
-/* Ethernet */
-#define CONFIG_MACB
-#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_MACB_SEARCH_PHY
-#define CONFIG_ETHADDR C0:EE:40:00:00:00
-
-/* System */
-#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
-
-#ifdef CONFIG_SYS_USE_NANDFLASH
-/* bootstrap + u-boot + env + linux in nandflash */
-
-#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0xe0000 0x280000; " \
- "run _mtd; bootm"
-
-#define MTDIDS_DEFAULT "nand0=atmel_nand"
-#define MTDPARTS_DEFAULT "mtdparts=atmel_nand:" \
- "128K(at91bs)," \
- "512K(u-boot)," \
- "128K(u-boot-env)," \
- "128K(redund-env)," \
- "2560K(kernel-a)," \
- "2560K(kernel-b)," \
- "38912K(rootfs-a)," \
- "38912K(rootfs-b)," \
- "46208K(user)," \
- "512K(logs)"
-
-#else
-#error No boot method selected, please select 'CONFIG_SYS_USE_NANDFLASH'
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "_mtd=mtdparts default; setenv bootargs ${bootargs} ${mtdparts}\0" \
- "autoload=no\0" \
- "autostart=no\0" \
- "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
- "\0"
-
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024 + 0x1000)
-
-/* SPL */
-#define CONFIG_SPL_MAX_SIZE 0x6000
-#define CONFIG_SPL_STACK 0x308000
-
-#define CONFIG_SPL_BSS_START_ADDR 0x20000000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
-#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
-
-#define CONFIG_SYS_MONITOR_LEN (512 << 10)
-
-#define CONFIG_SYS_MASTER_CLOCK 132096000
-#define CONFIG_SYS_AT91_PLLA 0x20c73f03
-#define CONFIG_SYS_MCKR 0x1301
-#define CONFIG_SYS_MCKR_CSS 0x1302
-
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
-
-#endif /* __CONFIG_H__ */
projects / u-boot.git / commitdiff
