Provide an explicit configuration option to disable default "lock"
of any flash chip which supports locking. By disabling the lock
config will save some amount of memory and also don't expose the
lock functionality to the users i.e., via sf protect command.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231003031715.5343-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
ret = do_spi_flash_read_write(argc, argv);
else if (strcmp(cmd, "erase") == 0)
ret = do_spi_flash_erase(argc, argv);
- else if (strcmp(cmd, "protect") == 0)
+ else if (IS_ENABLED(CONFIG_SPI_FLASH_LOCK) && strcmp(cmd, "protect") == 0)
ret = do_spi_protect(argc, argv);
else if (IS_ENABLED(CONFIG_CMD_SF_TEST) && !strcmp(cmd, "test"))
ret = do_spi_flash_test(argc, argv);
"sf update addr offset|partition len - erase and write `len' bytes from memory\n"
" at `addr' to flash at `offset'\n"
" or to start of mtd `partition'\n"
+#ifdef CONFIG_SPI_FLASH_LOCK
"sf protect lock/unlock sector len - protect/unprotect 'len' bytes starting\n"
" at address 'sector'"
+#endif
#ifdef CONFIG_CMD_SF_TEST
"\nsf test offset len - run a very basic destructive test"
#endif
Bank/Extended address registers are used to access the flash
which has size > 16MiB in 3-byte addressing.
+config SPI_FLASH_LOCK
+ bool "Enable the Locking feature"
+ default y
+ help
+ Enable the SPI flash lock support. By default this is set to y.
+ If you intend not to use the lock support you should say n here.
+
config SPI_FLASH_UNLOCK_ALL
bool "Unlock the entire SPI flash on u-boot startup"
default y
}
#endif
+#if defined(CONFIG_SPI_FLASH_LOCK)
#if defined(CONFIG_SPI_FLASH_STMICRO) || defined(CONFIG_SPI_FLASH_SST)
/* Write status register and ensure bits in mask match written values */
static int write_sr_and_check(struct spi_nor *nor, u8 status_new, u8 mask)
return stm_is_unlocked_sr(nor, ofs, len, status);
}
#endif /* CONFIG_SPI_FLASH_STMICRO */
+#endif
static const struct flash_info *spi_nor_read_id(struct spi_nor *nor)
{
return ret;
}
+#if defined(CONFIG_SPI_FLASH_LOCK)
#ifdef CONFIG_SPI_FLASH_SST
/*
* sst26 flash series has its own block protection implementation:
return ret;
}
#endif
+#endif
+
/*
* Write an address range to the nor chip. Data must be written in
* FLASH_PAGESIZE chunks. The address range may be any size provided
mtd->_read = spi_nor_read;
mtd->_write = spi_nor_write;
+#if defined(CONFIG_SPI_FLASH_LOCK)
#if defined(CONFIG_SPI_FLASH_STMICRO) || defined(CONFIG_SPI_FLASH_SST)
/* NOR protection support for STmicro/Micron chips and similar */
if (JEDEC_MFR(info) == SNOR_MFR_ST ||
nor->flash_is_unlocked = sst26_is_unlocked;
}
#endif
-
+#endif
if (info->flags & USE_FSR)
nor->flags |= SNOR_F_USE_FSR;
if (info->flags & SPI_NOR_HAS_TB)