ARM: display5: Remove UART initialization code after DM/DTS conversion (non-console)

This UART is not used in U-Boot, so there is no need to initialize it.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

diff --git a/board/liebherr/display5/common.c b/board/liebherr/display5/common.c
index d2d174beaa0d5ff357af8e8a7b4f8807a66797ff..5e714076a49c969f3a62399d00bcb86268d43fa6 100644 (file)
--- a/board/liebherr/display5/common.c
+++ b/board/liebherr/display5/common.c
@@ -8,14 +8,6 @@
 #include <asm/arch/mx6-pins.h>
 #include "common.h"
 
-iomux_v3_cfg_t const uart_pads[] = {
-       /* UART4 */
-       MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_CSI0_DAT16__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_CSI0_DAT17__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
 iomux_v3_cfg_t const uart_console_pads[] = {
        /* UART5 */
        MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
@@ -29,11 +21,6 @@ void displ5_set_iomux_uart_spl(void)
        SETUP_IOMUX_PADS(uart_console_pads);
 }
 
-void displ5_set_iomux_uart(void)
-{
-       SETUP_IOMUX_PADS(uart_pads);
-}
-
 iomux_v3_cfg_t const misc_pads_spl[] = {
        /* Emergency recovery pin */
        MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),

diff --git a/board/liebherr/display5/common.h b/board/liebherr/display5/common.h
index 2bbd934e7a7060f4b421365cfa9ca2e9b63e9732..4eb70dc42fb69614561123c070a21eb8529561af 100644 (file)
--- a/board/liebherr/display5/common.h
+++ b/board/liebherr/display5/common.h
@@ -32,7 +32,6 @@
        PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
 
 void displ5_set_iomux_uart_spl(void);
-void displ5_set_iomux_uart(void);
 void displ5_set_iomux_ecspi_spl(void);
 void displ5_set_iomux_usdhc_spl(void);
 void displ5_set_iomux_misc_spl(void);

diff --git a/board/liebherr/display5/display5.c b/board/liebherr/display5/display5.c
index 541e3e94a5eb1fb8291504d8d111e20c62fd9e8b..5713401ed954efa444731b6e805752f9de11eedd 100644 (file)
--- a/board/liebherr/display5/display5.c
+++ b/board/liebherr/display5/display5.c
@@ -174,8 +174,6 @@ int board_init(void)
        /* address of boot parameters */
        gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 
-       /* Setup iomux for non console UARTS */
-       displ5_set_iomux_uart();
        /* Setup misc (application specific) stuff */
        SETUP_IOMUX_PADS(misc_pads);