This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
dtb-$(CONFIG_TARGET_DEVKIT8000) += omap3-devkit8000.dtb
-dtb-$(CONFIG_TARGET_OMAP4_PANDA) += \
- omap4-panda.dtb \
- omap4-panda-es.dtb
-
dtb-$(CONFIG_TARGET_OMAP4_SDP4430) += \
omap4-sdp.dtb \
omap4-sdp-es23plus.dtb
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2011-2013 Texas Instruments Incorporated - https://www.ti.com/
- */
-#include <dt-bindings/input/input.h>
-#include "elpida_ecb240abacn.dtsi"
-#include "omap4-mcpdm.dtsi"
-
-/ {
- memory@80000000 {
- device_type = "memory";
- reg = <0x80000000 0x40000000>; /* 1 GB */
- };
-
- chosen {
- stdout-path = &uart3;
- };
-
- aliases {
- display0 = &dvi0;
- display1 = &hdmi0;
- ethernet = ðernet;
- };
-
- leds: leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <
- &led_wkgpio_pins
- >;
-
- led-heartbeat {
- label = "pandaboard::status1";
- gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
-
- led-mmc {
- label = "pandaboard::status2";
- gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- };
- };
-
- gpio_keys: gpio_keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <
- &button_pins
- >;
-
- buttonS2 {
- label = "button S2";
- gpios = <&gpio4 25 GPIO_ACTIVE_LOW>; /* gpio_121 */
- linux,code = <BTN_0>;
- wakeup-source;
- };
- };
-
- sound: sound {
- compatible = "ti,abe-twl6040";
- ti,model = "PandaBoard";
-
- ti,mclk-freq = <38400000>;
-
- ti,mcpdm = <&mcpdm>;
-
- ti,twl6040 = <&twl6040>;
-
- /* Audio routing */
- ti,audio-routing =
- "Headset Stereophone", "HSOL",
- "Headset Stereophone", "HSOR",
- "Ext Spk", "HFL",
- "Ext Spk", "HFR",
- "Line Out", "AUXL",
- "Line Out", "AUXR",
- "HSMIC", "Headset Mic",
- "Headset Mic", "Headset Mic Bias",
- "AFML", "Line In",
- "AFMR", "Line In";
- };
-
- /* HS USB Port 1 Power */
- hsusb1_power: hsusb1_power_reg {
- compatible = "regulator-fixed";
- regulator-name = "hsusb1_vbus";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; /* gpio_1 */
- startup-delay-us = <70000>;
- enable-active-high;
- /*
- * boot-on is required along with always-on as the
- * regulator framework doesn't enable the regulator
- * if boot-on is not there.
- */
- regulator-always-on;
- regulator-boot-on;
- };
-
- /* HS USB Host PHY on PORT 1 */
- hsusb1_phy: hsusb1_phy {
- compatible = "usb-nop-xceiv";
- reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */
- #phy-cells = <0>;
- vcc-supply = <&hsusb1_power>;
- clocks = <&auxclk3_ck>;
- clock-names = "main_clk";
- clock-frequency = <19200000>;
- };
-
- /* regulator for wl12xx on sdio5 */
- wl12xx_vmmc: wl12xx_vmmc {
- pinctrl-names = "default";
- pinctrl-0 = <&wl12xx_gpio>;
- compatible = "regulator-fixed";
- regulator-name = "vwl1271";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
- startup-delay-us = <70000>;
- enable-active-high;
- };
-
- tfp410: encoder0 {
- compatible = "ti,tfp410";
- powerdown-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* gpio_0 */
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tfp410_in: endpoint {
- remote-endpoint = <&dpi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- tfp410_out: endpoint {
- remote-endpoint = <&dvi_connector_in>;
- };
- };
- };
- };
-
- dvi0: connector0 {
- compatible = "dvi-connector";
- label = "dvi";
-
- digital;
-
- ddc-i2c-bus = <&i2c3>;
-
- port {
- dvi_connector_in: endpoint {
- remote-endpoint = <&tfp410_out>;
- };
- };
- };
-
- tpd12s015: encoder1 {
- compatible = "ti,tpd12s015";
-
- gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
- <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
- <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- tpd12s015_in: endpoint {
- remote-endpoint = <&hdmi_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- tpd12s015_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
- };
- };
- };
-
- hdmi0: connector1 {
- compatible = "hdmi-connector";
- label = "hdmi";
-
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&tpd12s015_out>;
- };
- };
- };
-};
-
-&omap4_pmx_core {
- pinctrl-names = "default";
- pinctrl-0 = <
- &dss_dpi_pins
- &tfp410_pins
- &dss_hdmi_pins
- &tpd12s015_pins
- &hsusbb1_pins
- >;
-
- twl6040_pins: pinmux_twl6040_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */
- OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */
- >;
- };
-
- mcbsp1_pins: pinmux_mcbsp1_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
- OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */
- OMAP4_IOPAD(0x102, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */
- OMAP4_IOPAD(0x104, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */
- >;
- };
-
- dss_dpi_pins: pinmux_dss_dpi_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x162, PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */
- OMAP4_IOPAD(0x164, PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */
- OMAP4_IOPAD(0x166, PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */
- OMAP4_IOPAD(0x168, PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */
- OMAP4_IOPAD(0x16a, PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */
- OMAP4_IOPAD(0x16c, PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */
- OMAP4_IOPAD(0x16e, PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */
- OMAP4_IOPAD(0x170, PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */
- OMAP4_IOPAD(0x172, PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */
- OMAP4_IOPAD(0x174, PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */
- OMAP4_IOPAD(0x176, PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */
-
- OMAP4_IOPAD(0x1b4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */
- OMAP4_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */
- OMAP4_IOPAD(0x1b8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */
- OMAP4_IOPAD(0x1ba, PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */
- OMAP4_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */
- OMAP4_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */
- OMAP4_IOPAD(0x1c0, PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */
- OMAP4_IOPAD(0x1c2, PIN_OUTPUT | MUX_MODE5) /* dispc2_de */
- OMAP4_IOPAD(0x1c4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */
- OMAP4_IOPAD(0x1c6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */
- OMAP4_IOPAD(0x1c8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */
- OMAP4_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */
- OMAP4_IOPAD(0x1cc, PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */
- OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */
-
- OMAP4_IOPAD(0x1d0, PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */
- OMAP4_IOPAD(0x1d2, PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */
- OMAP4_IOPAD(0x1d4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */
- >;
- };
-
- tfp410_pins: pinmux_tfp410_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x184, PIN_OUTPUT | MUX_MODE3) /* gpio_0 */
- >;
- };
-
- dss_hdmi_pins: pinmux_dss_hdmi_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
- OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
- OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
- >;
- };
-
- tpd12s015_pins: pinmux_tpd12s015_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */
- OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */
- OMAP4_IOPAD(0x098, PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */
- >;
- };
-
- hsusbb1_pins: pinmux_hsusbb1_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x0c2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
- OMAP4_IOPAD(0x0c4, PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
- OMAP4_IOPAD(0x0c6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
- OMAP4_IOPAD(0x0c8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
- OMAP4_IOPAD(0x0ca, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
- OMAP4_IOPAD(0x0cc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
- OMAP4_IOPAD(0x0ce, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
- OMAP4_IOPAD(0x0d0, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
- OMAP4_IOPAD(0x0d2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
- OMAP4_IOPAD(0x0d4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
- OMAP4_IOPAD(0x0d6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
- OMAP4_IOPAD(0x0d8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
- >;
- };
-
- i2c1_pins: pinmux_i2c1_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
- OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
- >;
- };
-
- i2c2_pins: pinmux_i2c2_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
- OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
- >;
- };
-
- i2c3_pins: pinmux_i2c3_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
- OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
- >;
- };
-
- i2c4_pins: pinmux_i2c4_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
- OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
- >;
- };
-
- /*
- * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP
- * REVISIT: Are the pull-ups needed for GPIO 48 and 49?
- */
- wl12xx_gpio: pinmux_wl12xx_gpio {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 */
- OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 */
- OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */
- OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 */
- >;
- };
-
- /* wl12xx GPIO inputs and SDIO pins */
- wl12xx_pins: pinmux_wl12xx_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */
- OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */
- OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */
- OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */
- OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */
- OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */
- OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */
- OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */
- >;
- };
-
- button_pins: pinmux_button_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x114, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_121 */
- >;
- };
-};
-
-&omap4_pmx_wkup {
- led_wkgpio_pins: pinmux_leds_wkpins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */
- OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
- >;
- };
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
-
- clock-frequency = <400000>;
-
- twl: twl@48 {
- reg = <0x48>;
- /* IRQ# = 7 */
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
- };
-
- twl6040: twl@4b {
- compatible = "ti,twl6040";
- #clock-cells = <0>;
- reg = <0x4b>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&twl6040_pins>;
-
- /* IRQ# = 119 */
- interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
- ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */
-
- vio-supply = <&v1v8>;
- v2v1-supply = <&v2v1>;
- enable-active-high;
- };
-};
-
-#include "twl6030.dtsi"
-#include "twl6030_omap4.dtsi"
-
-&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
-
- clock-frequency = <400000>;
-};
-
-&i2c3 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins>;
-
- clock-frequency = <100000>;
-
- /*
- * Display monitor features are burnt in their EEPROM as EDID data.
- * The EEPROM is connected as I2C slave device.
- */
- eeprom@50 {
- compatible = "ti,eeprom";
- reg = <0x50>;
- };
-};
-
-&i2c4 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c4_pins>;
-
- clock-frequency = <400000>;
-};
-
-&mmc1 {
- vmmc-supply = <&vmmc>;
- bus-width = <8>;
-};
-
-&mmc2 {
- status = "disabled";
-};
-
-&mmc3 {
- status = "disabled";
-};
-
-&mmc4 {
- status = "disabled";
-};
-
-&mmc5 {
- pinctrl-names = "default";
- pinctrl-0 = <&wl12xx_pins>;
- vmmc-supply = <&wl12xx_vmmc>;
- interrupts-extended = <&wakeupgen GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH
- &omap4_pmx_core 0x10e>;
- non-removable;
- bus-width = <4>;
- cap-power-off-card;
-
- #address-cells = <1>;
- #size-cells = <0>;
- wlcore: wlcore@2 {
- compatible = "ti,wl1271";
- reg = <2>;
- /* gpio_53 with gpmc_ncs3 pad as wakeup */
- interrupts-extended = <&gpio2 21 IRQ_TYPE_LEVEL_HIGH>,
- <&omap4_pmx_core 0x3a>;
- interrupt-names = "irq", "wakeup";
- ref-clock-frequency = <38400000>;
- };
-};
-
-&emif1 {
- cs1-used;
- device-handle = <&elpida_ECB240ABACN>;
-};
-
-&emif2 {
- cs1-used;
- device-handle = <&elpida_ECB240ABACN>;
-};
-
-&mcbsp1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mcbsp1_pins>;
- status = "okay";
-};
-
-&twl_usb_comparator {
- usb-supply = <&vusb>;
-};
-
-&uart2 {
- interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
- &omap4_pmx_core OMAP4_UART2_RX>;
-};
-
-&uart3 {
- interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
- &omap4_pmx_core OMAP4_UART3_RX>;
-};
-
-&uart4 {
- interrupts-extended = <&wakeupgen GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH
- &omap4_pmx_core OMAP4_UART4_RX>;
-};
-
-&usb_otg_hs {
- interface-type = <1>;
- mode = <3>;
- power = <50>;
-};
-
-&usbhshost {
- port1-mode = "ehci-phy";
-};
-
-&usbhsehci {
- phys = <&hsusb1_phy>;
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- hub@1 {
- compatible = "usb424,9514";
- reg = <1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethernet: ethernet@1 {
- compatible = "usb424,ec00";
- reg = <1>;
- };
- };
-};
-
-&dss {
- status = "okay";
-
- port {
- dpi_out: endpoint {
- remote-endpoint = <&tfp410_in>;
- data-lines = <24>;
- };
- };
-};
-
-&dsi2 {
- status = "okay";
- vdd-supply = <&vcxio>;
-};
-
-&hdmi {
- status = "okay";
- vdda-supply = <&vdac>;
-
- port {
- hdmi_out: endpoint {
- remote-endpoint = <&tpd12s015_in>;
- };
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- */
-/dts-v1/;
-
-#include "omap4460.dtsi"
-#include "omap4-panda-common.dtsi"
-
-/ {
- model = "TI OMAP4 PandaBoard-ES";
- compatible = "ti,omap4-panda-es", "ti,omap4-panda", "ti,omap4460", "ti,omap4430", "ti,omap4";
-};
-
-/* Audio routing is differnet between PandaBoard4430 and PandaBoardES */
-&sound {
- ti,model = "PandaBoardES";
-
- /* Audio routing */
- ti,audio-routing =
- "Headset Stereophone", "HSOL",
- "Headset Stereophone", "HSOR",
- "Ext Spk", "HFL",
- "Ext Spk", "HFR",
- "Line Out", "AUXL",
- "Line Out", "AUXR",
- "AFML", "Line In",
- "AFMR", "Line In";
-};
-
-/* PandaboardES has external pullups on SCL & SDA */
-&dss_hdmi_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
- OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */
- OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */
- >;
-};
-
-&omap4_pmx_core {
- led_gpio_pins: gpio_led_pmx {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x0f6, PIN_OUTPUT | MUX_MODE3) /* gpio_110 */
- >;
- };
-
- button_pins: pinmux_button_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x11b, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_113 */
- >;
- };
-};
-
-&led_wkgpio_pins {
- pinctrl-single,pins = <
- OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
- >;
-};
-
-&leds {
- pinctrl-0 = <
- &led_gpio_pins
- &led_wkgpio_pins
- >;
-
- led-heartbeat {
- gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
- };
- led-mmc {
- gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
- };
-};
-
-&gpio_keys {
- buttonS2 {
- gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* gpio_113 */
- };
-};
-
-&gpio1_target {
- ti,no-reset-on-init;
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
- */
-/dts-v1/;
-
-#include "omap443x.dtsi"
-#include "omap4-panda-common.dtsi"
-
-/ {
- model = "TI OMAP4 PandaBoard";
- compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4";
-};
prompt "OMAP4 board select"
optional
-config TARGET_OMAP4_PANDA
- bool "TI OMAP4 PandaBoard"
-
config TARGET_OMAP4_SDP4430
bool "TI OMAP4 SDP4430"
config SYS_SOC
default "omap4"
-source "board/ti/panda/Kconfig"
source "board/ti/sdp4430/Kconfig"
endif
+++ /dev/null
-if TARGET_OMAP4_PANDA
-
-config SYS_BOARD
- default "panda"
-
-config SYS_VENDOR
- default "ti"
-
-config SYS_CONFIG_NAME
- default "omap4_panda"
-
-source "board/ti/common/Kconfig"
-
-endif
+++ /dev/null
-PANDA BOARD
-M: Tom Rini <trini@konsulko.com>
-S: Maintained
-F: board/ti/panda/
-F: include/configs/omap4_panda.h
-F: configs/omap4_panda_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y := panda.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2010
- * Texas Instruments Incorporated, <www.ti.com>
- * Steve Sakoman <steve@sakoman.com>
- */
-#include <init.h>
-#include <log.h>
-#include <net.h>
-#include <serial.h>
-#include <asm/global_data.h>
-#include <asm/mach-types.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/mmc_host_def.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/gpio.h>
-#include <asm/gpio.h>
-#include <env.h>
-#include <twl6030.h>
-
-#include "panda_mux_data.h"
-
-#define PANDA_ULPI_PHY_TYPE_GPIO 182
-#define PANDA_BOARD_ID_1_GPIO 101
-#define PANDA_ES_BOARD_ID_1_GPIO 48
-#define PANDA_BOARD_ID_2_GPIO 171
-#define PANDA_ES_BOARD_ID_3_GPIO 3
-#define PANDA_ES_BOARD_ID_4_GPIO 2
-
-DECLARE_GLOBAL_DATA_PTR;
-
-const struct omap_sysinfo sysinfo = {
- "Board: OMAP4 Panda\n"
-};
-
-struct omap4_scrm_regs *const scrm = (struct omap4_scrm_regs *)0x4a30a000;
-
-/**
- * @brief board_init
- *
- * Return: 0
- */
-int board_init(void)
-{
- gpmc_init();
-
- gd->bd->bi_arch_number = MACH_TYPE_OMAP4_PANDA;
- gd->bd->bi_boot_params = (0x80000000 + 0x100); /* boot param addr */
-
- return 0;
-}
-
-#if defined(CONFIG_SPL_OS_BOOT)
-int spl_start_uboot(void)
-{
- /* break into full u-boot on 'c' */
- if (serial_tstc() && serial_getc() == 'c')
- return 1;
-
- return 0;
-}
-#endif /* CONFIG_SPL_OS_BOOT */
-
-int board_eth_init(struct bd_info *bis)
-{
- return 0;
-}
-
-/*
-* Routine: get_board_revision
-* Description: Detect if we are running on a panda revision A1-A6,
-* or an ES panda board. This can be done by reading
-* the level of GPIOs and checking the processor revisions.
-* This should result in:
-* Panda 4430:
-* GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
-* GPIO171, GPIO101, GPIO182: 1 0 1 => A6
-* Panda ES:
-* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
-* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
-*/
-int get_board_revision(void)
-{
- int board_id0, board_id1, board_id2;
- int board_id3, board_id4;
- int board_id;
-
- int processor_rev = omap_revision();
-
- /* Setup the mux for the common board ID pins (gpio 171 and 182) */
- writew((IEN | M3), (*ctrl)->control_padconf_core_base + UNIPRO_TX0);
- writew((IEN | M3), (*ctrl)->control_padconf_core_base + FREF_CLK2_OUT);
-
- board_id0 = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
- board_id2 = gpio_get_value(PANDA_BOARD_ID_2_GPIO);
-
- if ((processor_rev >= OMAP4460_ES1_0 &&
- processor_rev <= OMAP4460_ES1_1)) {
- /*
- * Setup the mux for the ES specific board ID pins (gpio 101,
- * 2 and 3.
- */
- writew((IEN | M3), (*ctrl)->control_padconf_core_base +
- GPMC_A24);
- writew((IEN | M3), (*ctrl)->control_padconf_core_base +
- UNIPRO_RY0);
- writew((IEN | M3), (*ctrl)->control_padconf_core_base +
- UNIPRO_RX1);
-
- board_id1 = gpio_get_value(PANDA_ES_BOARD_ID_1_GPIO);
- board_id3 = gpio_get_value(PANDA_ES_BOARD_ID_3_GPIO);
- board_id4 = gpio_get_value(PANDA_ES_BOARD_ID_4_GPIO);
-
-#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- env_set("board_name", "panda-es");
-#endif
- board_id = ((board_id4 << 4) | (board_id3 << 3) |
- (board_id2 << 2) | (board_id1 << 1) | (board_id0));
- } else {
- /* Setup the mux for the Ax specific board ID pins (gpio 101) */
- writew((IEN | M3), (*ctrl)->control_padconf_core_base +
- FREF_CLK2_OUT);
-
- board_id1 = gpio_get_value(PANDA_BOARD_ID_1_GPIO);
- board_id = ((board_id2 << 2) | (board_id1 << 1) | (board_id0));
-
-#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- if ((board_id >= 0x3) && (processor_rev == OMAP4430_ES2_3))
- env_set("board_name", "panda-a4");
-#endif
- }
-
- return board_id;
-}
-
-/**
- * is_panda_es_rev_b3() - Detect if we are running on rev B3 of panda board ES
- *
- *
- * Detect if we are running on B3 version of ES panda board,
- * This can be done by reading the level of GPIO 171 and checking the
- * processor revisions.
- * GPIO171: 1 => Panda ES Rev B3
- *
- * Return : return 1 if Panda ES Rev B3 , else return 0
- */
-u8 is_panda_es_rev_b3(void)
-{
- int processor_rev = omap_revision();
- int ret = 0;
-
- if ((processor_rev >= OMAP4460_ES1_0 &&
- processor_rev <= OMAP4460_ES1_1)) {
-
- /* Setup the mux for the common board ID pins (gpio 171) */
- writew((IEN | M3),
- (*ctrl)->control_padconf_core_base + UNIPRO_TX0);
-
- /* if processor_rev is panda ES and GPIO171 is 1,it is rev b3 */
- ret = gpio_get_value(PANDA_BOARD_ID_2_GPIO);
- }
- return ret;
-}
-
-#ifdef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
-/*
- * emif_get_reg_dump() - emif_get_reg_dump strong function
- *
- * @emif_nr - emif base
- * @regs - reg dump of timing values
- *
- * Strong function to override emif_get_reg_dump weak function in sdram_elpida.c
- */
-void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs)
-{
- u32 omap4_rev = omap_revision();
-
- /* Same devices and geometry on both EMIFs */
- if (omap4_rev == OMAP4430_ES1_0)
- *regs = &emif_regs_elpida_380_mhz_1cs;
- else if (omap4_rev == OMAP4430_ES2_0)
- *regs = &emif_regs_elpida_200_mhz_2cs;
- else if (omap4_rev == OMAP4430_ES2_3)
- *regs = &emif_regs_elpida_400_mhz_1cs;
- else if (omap4_rev < OMAP4470_ES1_0) {
- if(is_panda_es_rev_b3())
- *regs = &emif_regs_elpida_400_mhz_1cs;
- else
- *regs = &emif_regs_elpida_400_mhz_2cs;
- }
- else
- *regs = &emif_regs_elpida_400_mhz_1cs;
-}
-
-void emif_get_dmm_regs(const struct dmm_lisa_map_regs
- **dmm_lisa_regs)
-{
- u32 omap_rev = omap_revision();
-
- if (omap_rev == OMAP4430_ES1_0)
- *dmm_lisa_regs = &lisa_map_2G_x_1_x_2;
- else if (omap_rev == OMAP4430_ES2_3)
- *dmm_lisa_regs = &lisa_map_2G_x_2_x_2;
- else if (omap_rev < OMAP4460_ES1_0)
- *dmm_lisa_regs = &lisa_map_2G_x_2_x_2;
- else
- *dmm_lisa_regs = &ma_lisa_map_2G_x_2_x_2;
-}
-
-#endif
-
-/**
- * @brief misc_init_r - Configure Panda board specific configurations
- * such as power configurations, ethernet initialization as phase2 of
- * boot sequence
- *
- * Return: 0
- */
-int misc_init_r(void)
-{
- int phy_type;
- u32 auxclk, altclksrc;
-
- /* EHCI is not supported on ES1.0 */
- if (omap_revision() == OMAP4430_ES1_0)
- return 0;
-
- get_board_revision();
-
- gpio_direction_input(PANDA_ULPI_PHY_TYPE_GPIO);
- phy_type = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
-
- if (phy_type == 1) {
- /* ULPI PHY supplied by auxclk3 derived from sys_clk */
- debug("ULPI PHY supplied by auxclk3\n");
-
- auxclk = readl(&scrm->auxclk3);
- /* Select sys_clk */
- auxclk &= ~AUXCLK_SRCSELECT_MASK;
- auxclk |= AUXCLK_SRCSELECT_SYS_CLK << AUXCLK_SRCSELECT_SHIFT;
- /* Set the divisor to 2 */
- auxclk &= ~AUXCLK_CLKDIV_MASK;
- auxclk |= AUXCLK_CLKDIV_2 << AUXCLK_CLKDIV_SHIFT;
- /* Request auxilary clock #3 */
- auxclk |= AUXCLK_ENABLE_MASK;
-
- writel(auxclk, &scrm->auxclk3);
- } else {
- /* ULPI PHY supplied by auxclk1 derived from PER dpll */
- debug("ULPI PHY supplied by auxclk1\n");
-
- auxclk = readl(&scrm->auxclk1);
- /* Select per DPLL */
- auxclk &= ~AUXCLK_SRCSELECT_MASK;
- auxclk |= AUXCLK_SRCSELECT_PER_DPLL << AUXCLK_SRCSELECT_SHIFT;
- /* Set the divisor to 16 */
- auxclk &= ~AUXCLK_CLKDIV_MASK;
- auxclk |= AUXCLK_CLKDIV_16 << AUXCLK_CLKDIV_SHIFT;
- /* Request auxilary clock #3 */
- auxclk |= AUXCLK_ENABLE_MASK;
-
- writel(auxclk, &scrm->auxclk1);
- }
-
- altclksrc = readl(&scrm->altclksrc);
-
- /* Activate alternate system clock supplier */
- altclksrc &= ~ALTCLKSRC_MODE_MASK;
- altclksrc |= ALTCLKSRC_MODE_ACTIVE;
-
- /* enable clocks */
- altclksrc |= ALTCLKSRC_ENABLE_INT_MASK | ALTCLKSRC_ENABLE_EXT_MASK;
-
- writel(altclksrc, &scrm->altclksrc);
-
- omap_die_id_usbethaddr();
-
- return 0;
-}
-
-void set_muxconf_regs(void)
-{
- do_set_mux((*ctrl)->control_padconf_core_base,
- core_padconf_array_essential,
- sizeof(core_padconf_array_essential) /
- sizeof(struct pad_conf_entry));
-
- do_set_mux((*ctrl)->control_padconf_wkup_base,
- wkup_padconf_array_essential,
- sizeof(wkup_padconf_array_essential) /
- sizeof(struct pad_conf_entry));
-
- if (omap_revision() >= OMAP4460_ES1_0)
- do_set_mux((*ctrl)->control_padconf_wkup_base,
- wkup_padconf_array_essential_4460,
- sizeof(wkup_padconf_array_essential_4460) /
- sizeof(struct pad_conf_entry));
-}
-
-#if defined(CONFIG_MMC)
-int board_mmc_init(struct bd_info *bis)
-{
- return omap_mmc_init(0, 0, 0, -1, -1);
-}
-
-#if !defined(CONFIG_SPL_BUILD)
-void board_mmc_power_init(void)
-{
- twl6030_power_mmc_init(0);
-}
-#endif
-#endif
-
-#ifdef CONFIG_REVISION_TAG
-/*
- * get_board_rev() - get board revision
- */
-u32 get_board_rev(void)
-{
- return 0x20;
-}
-#endif
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2010
- * Texas Instruments Incorporated, <www.ti.com>
- *
- * Balaji Krishnamoorthy <balajitk@ti.com>
- * Aneesh V <aneesh@ti.com>
- */
-#ifndef _PANDA_MUX_DATA_H_
-#define _PANDA_MUX_DATA_H_
-
-#include <asm/arch/mux_omap4.h>
-
-const struct pad_conf_entry core_padconf_array_essential[] = {
-
-{GPMC_AD0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat0 */
-{GPMC_AD1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat1 */
-{GPMC_AD2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat2 */
-{GPMC_AD3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat3 */
-{GPMC_AD4, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat4 */
-{GPMC_AD5, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat5 */
-{GPMC_AD6, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat6 */
-{GPMC_AD7, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat7 */
-{GPMC_NOE, (PTU | IEN | OFF_EN | OFF_OUT_PTD | M1)}, /* sdmmc2_clk */
-{GPMC_NWE, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_cmd */
-{SDMMC1_CLK, (PTU | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc1_clk */
-{SDMMC1_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_cmd */
-{SDMMC1_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat0 */
-{SDMMC1_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat1 */
-{SDMMC1_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat2 */
-{SDMMC1_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat3 */
-{SDMMC1_DAT4, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat4 */
-{SDMMC1_DAT5, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat5 */
-{SDMMC1_DAT6, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat6 */
-{SDMMC1_DAT7, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat7 */
-{I2C1_SCL, (PTU | IEN | M0)}, /* i2c1_scl */
-{I2C1_SDA, (PTU | IEN | M0)}, /* i2c1_sda */
-{I2C2_SCL, (PTU | IEN | M0)}, /* i2c2_scl */
-{I2C2_SDA, (PTU | IEN | M0)}, /* i2c2_sda */
-{I2C3_SCL, (PTU | IEN | M0)}, /* i2c3_scl */
-{I2C3_SDA, (PTU | IEN | M0)}, /* i2c3_sda */
-{I2C4_SCL, (PTU | IEN | M0)}, /* i2c4_scl */
-{I2C4_SDA, (PTU | IEN | M0)}, /* i2c4_sda */
-{UART3_CTS_RCTX, (PTU | IEN | M0)}, /* uart3_tx */
-{UART3_RTS_SD, (M0)}, /* uart3_rts_sd */
-{UART3_RX_IRRX, (IEN | M0)}, /* uart3_rx */
-{UART3_TX_IRTX, (M0)}, /* uart3_tx */
-{USBB1_ULPITLL_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M4)},/* usbb1_ulpiphy_clk */
-{USBB1_ULPITLL_STP, (OFF_EN | OFF_OUT_PTD | M4)}, /* usbb1_ulpiphy_stp */
-{USBB1_ULPITLL_DIR, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dir */
-{USBB1_ULPITLL_NXT, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_nxt */
-{USBB1_ULPITLL_DAT0, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat0 */
-{USBB1_ULPITLL_DAT1, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat1 */
-{USBB1_ULPITLL_DAT2, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat2 */
-{USBB1_ULPITLL_DAT3, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat3 */
-{USBB1_ULPITLL_DAT4, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat4 */
-{USBB1_ULPITLL_DAT5, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat5 */
-{USBB1_ULPITLL_DAT6, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat6 */
-{USBB1_ULPITLL_DAT7, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat7 */
-{USBB1_HSIC_DATA, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usbb1_hsic_data */
-{USBB1_HSIC_STROBE, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usbb1_hsic_strobe */
-{USBC1_ICUSB_DP, (IEN | M0)}, /* usbc1_icusb_dp */
-{USBC1_ICUSB_DM, (IEN | M0)}, /* usbc1_icusb_dm */
-{UNIPRO_TY2, (PTU | IEN | M3)}, /* gpio_1 */
-{GPMC_WAIT1, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_62 */
-{FREF_CLK2_OUT, (PTU | IEN | M3)}, /* gpio_182 */
-
-};
-
-const struct pad_conf_entry wkup_padconf_array_essential[] = {
-
-{PAD1_SR_SCL, (PTU | IEN | M0)}, /* sr_scl */
-{PAD0_SR_SDA, (PTU | IEN | M0)}, /* sr_sda */
-{PAD1_SYS_32K, (IEN | M0)}, /* sys_32k */
-{PAD0_FREF_CLK3_OUT, (M0)}, /* fref_clk3_out */
-
-};
-
-const struct pad_conf_entry wkup_padconf_array_essential_4460[] = {
-
-{PAD1_FREF_CLK4_REQ, (M3)}, /* gpio_wk7 for TPS: Mode 3 */
-
-};
-
-#endif /* _PANDA_MUX_DATA_H_ */
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_SYS_L2_PL310=y
-CONFIG_ARCH_OMAP2PLUS=y
-CONFIG_SYS_MALLOC_F_LEN=0x4000
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030df00
-CONFIG_DEFAULT_DEVICE_TREE="omap4-panda"
-CONFIG_SPL_TEXT_BASE=0x40300000
-CONFIG_OMAP44XX=y
-CONFIG_TARGET_OMAP4_PANDA=y
-CONFIG_SPL=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_BOOTCOMMAND="if test ${boot_fit} -eq 1; then run update_to_fit; fi; run findfdt; run init_console; run envboot; run distro_bootcmd"
-CONFIG_DEFAULT_FDT_FILE="omap4-panda.dtb"
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-CONFIG_SPL_MAX_SIZE=0xbc00
-CONFIG_SPL_SYS_MALLOC=y
-CONFIG_SPL_SYS_MALLOC_SIZE=0x800000
-# CONFIG_SPL_FS_EXT4 is not set
-# CONFIG_SPL_I2C is not set
-# CONFIG_SPL_NAND_SUPPORT is not set
-CONFIG_SPL_OS_BOOT=y
-CONFIG_SPL_FALCON_BOOT_MMCSD=y
-CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR=0x1700
-CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR=0x1500
-CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS=0x200
-CONFIG_CMD_SPL=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FAT=y
-CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_VERSION_VARIABLE=y
-CONFIG_SYS_I2C_LEGACY=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
-CONFIG_MMC_OMAP_HS=y
-CONFIG_TWL6030_POWER=y
-CONFIG_CONS_INDEX=3
-CONFIG_SYS_NS16550_SERIAL=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_OMAP3=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_USB_GADGET=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2010
- * Texas Instruments Incorporated.
- * Steve Sakoman <steve@sakoman.com>
- *
- * Configuration settings for the TI OMAP4 Panda board.
- * See ti_omap4_common.h for OMAP4 common part
- */
-
-#ifndef __CONFIG_PANDA_H
-#define __CONFIG_PANDA_H
-
-#include <configs/ti_omap4_common.h>
-
-#endif /* __CONFIG_PANDA_H */
projects / u-boot.git / commitdiff
