int board_revision(void)
{
unsigned long cntrl0Reg;
- volatile unsigned long value;
+ unsigned long value;
/*
* Get version of APC405 board from GPIO's
#include <common.h>
#include "ar405.h"
#include <asm/processor.h>
+#include <asm/io.h>
#include <command.h>
DECLARE_GLOBAL_DATA_PTR;
mtdcr (uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority */
mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
- *(ushort *) 0xf03000ec = 0x0fff; /* enable all interrupts in fpga */
+ out_be16((void *)0xf03000ec, 0x0fff); /* enable interrupts in fpga */
return 0;
}
-
-/* ------------------------------------------------------------------------- */
-
/*
* Check Board Identity:
*/
-
int checkboard (void)
{
int index;
#if 1 /* test-only: some internal test routines... */
+#define DIGEN ((void *)0xf03000b4) /* u8 */
+#define DIGOUT ((void *)0xf03000b0) /* u16 */
+#define DIGIN ((void *)0xf03000a0) /* u16 */
+
/*
* Some test routines
*/
int do_digtest(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
- volatile uchar *digen = (volatile uchar *)0xf03000b4;
- volatile ushort *digout = (volatile ushort *)0xf03000b0;
- volatile ushort *digin = (volatile ushort *)0xf03000a0;
int i;
int k;
int start;
/*
* Enable digital outputs
*/
- *digen = 0x08;
+ out_8(DIGEN, 0x08);
printf("\nStarting digital In-/Out Test from I/O %d to %d (Cntrl-C to abort)...\n",
start, end);
*/
for (;;) {
for (i=start; i<=end; i++) {
- *digout = 0x0001 << i;
+ out_be16(DIGOUT, 0x0001 << i);
for (k=0; k<200; k++)
udelay(1000);
- if (*digin != (0x0001 << i)) {
- printf("ERROR: OUT=0x%04X, IN=0x%04X\n", 0x0001 << i, *digin);
+ if (in_be16(DIGIN) != (0x0001 << i)) {
+ printf("ERROR: OUT=0x%04X, IN=0x%04X\n",
+ 0x0001 << i, in_be16(DIGIN));
return 0;
}
#define ERROR_DELTA 256
struct io {
- volatile short val;
+ short val;
short dummy;
};
int do_anatest(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
- volatile short val;
+ short val;
int i;
int volt;
struct io *out;
volt = 0;
printf("Setting Channel %d to %dV...\n", i, volt);
- out[i].val = (volt * 0x7fff) / 10;
+ out_be16((void *)&(out[i].val), (volt * 0x7fff) / 10);
udelay(10000);
- val = in[i*2].val;
+ val = in_be16((void *)&(in[i*2].val));
printf("-> InChannel %d: 0x%04x=%dV\n", i*2, val, (val * 4000) / 0x7fff);
if ((val < ((volt * 0x7fff) / 40) - ERROR_DELTA) ||
(val > ((volt * 0x7fff) / 40) + ERROR_DELTA)) {
((volt * 0x7fff) / 40) + ERROR_DELTA);
return -1;
}
- val = in[i*2+1].val;
+ val = in_be16((void *)&(in[i*2+1].val));
printf("-> InChannel %d: 0x%04x=%dV\n", i*2+1, val, (val * 4000) / 0x7fff);
if ((val < ((volt * 0x7fff) / 40) - ERROR_DELTA) ||
(val > ((volt * 0x7fff) / 40) + ERROR_DELTA)) {
volt = 5;
printf("Setting Channel %d to %dV...\n", i, volt);
- out[i].val = (volt * 0x7fff) / 10;
+ out_be16((void *)&(out[i].val), (volt * 0x7fff) / 10);
udelay(10000);
- val = in[i*2].val;
+ val = in_be16((void *)&(in[i*2].val));
printf("-> InChannel %d: 0x%04x=%dV\n", i*2, val, (val * 4000) / 0x7fff);
if ((val < ((volt * 0x7fff) / 40) - ERROR_DELTA) ||
(val > ((volt * 0x7fff) / 40) + ERROR_DELTA)) {
((volt * 0x7fff) / 40) + ERROR_DELTA);
return -1;
}
- val = in[i*2+1].val;
+ val = in_be16((void *)&(in[i*2+1].val));
printf("-> InChannel %d: 0x%04x=%dV\n", i*2+1, val, (val * 4000) / 0x7fff);
if ((val < ((volt * 0x7fff) / 40) - ERROR_DELTA) ||
(val > ((volt * 0x7fff) / 40) + ERROR_DELTA)) {
volt = 10;
printf("Setting Channel %d to %dV...\n", i, volt);
- out[i].val = (volt * 0x7fff) / 10;
+ out_be16((void *)&(out[i].val), (volt * 0x7fff) / 10);
udelay(10000);
- val = in[i*2].val;
+ val = in_be16((void *)&(in[i*2].val));
printf("-> InChannel %d: 0x%04x=%dV\n", i*2, val, (val * 4000) / 0x7fff);
if ((val < ((volt * 0x7fff) / 40) - ERROR_DELTA) ||
(val > ((volt * 0x7fff) / 40) + ERROR_DELTA)) {
((volt * 0x7fff) / 40) + ERROR_DELTA);
return -1;
}
- val = in[i*2+1].val;
+ val = in_be16((void *)&(in[i*2+1].val));
printf("-> InChannel %d: 0x%04x=%dV\n", i*2+1, val, (val * 4000) / 0x7fff);
if ((val < ((volt * 0x7fff) / 40) - ERROR_DELTA) ||
(val > ((volt * 0x7fff) / 40) + ERROR_DELTA)) {
void cyclicInt(void *ptr)
{
- *(ushort *)0xf03000e8 = 0x0800; /* ack int */
+ out_be16((void *)0xf03000e8, 0x0800); /* ack int */
counter++;
}
int do_inctest(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
- volatile uchar *digout = (volatile uchar *)0xf03000b4;
- volatile ulong *incin;
+ ulong *incin;
int i;
- incin = (volatile ulong *)0xf0300040;
+ incin = (ulong *)0xf0300040;
/*
* Clear inc counter
*/
- incin[0] = 0;
- incin[1] = 0;
- incin[2] = 0;
- incin[3] = 0;
+ out_be32((void *)&incin[0], 0);
+ out_be32((void *)&incin[1], 0);
+ out_be32((void *)&incin[2], 0);
+ out_be32((void *)&incin[3], 0);
- incin = (volatile ulong *)0xf0300050;
+ incin = (ulong *)0xf0300050;
/*
* Inc a little
for (i=0; i<10000; i++) {
switch (i & 0x03) {
case 0:
- *digout = 0x02;
+ out_8(DIGEN, 0x02);
break;
case 1:
- *digout = 0x03;
+ out_8(DIGEN, 0x03);
break;
case 2:
- *digout = 0x01;
+ out_8(DIGEN, 0x01);
break;
case 3:
- *digout = 0x00;
+ out_8(DIGEN, 0x00);
break;
}
udelay(10);
}
- printf("Inc 0 = %ld\n", incin[0]);
- printf("Inc 1 = %ld\n", incin[1]);
- printf("Inc 2 = %ld\n", incin[2]);
- printf("Inc 3 = %ld\n", incin[3]);
+ printf("Inc 0 = %d\n", in_be32((void *)&incin[0]));
+ printf("Inc 1 = %d\n", in_be32((void *)&incin[1]));
+ printf("Inc 2 = %d\n", in_be32((void *)&incin[2]));
+ printf("Inc 3 = %d\n", in_be32((void *)&incin[3]));
- *(ushort *)0xf03000e0 = 0x0c80-1; /* set counter */
- *(ushort *)0xf03000ec |= 0x0800; /* enable int */
+ out_be16((void *)0xf03000e0, 0x0c80-1); /* set counter */
+ out_be16((void *)0xf03000ec,
+ in_be16((void *)0xf03000ec) | 0x0800); /* enable int */
irq_install_handler (30, (interrupt_handler_t *) cyclicInt, NULL);
printf("counter=%d\n", counter);
int misc_init_r (void)
{
- volatile unsigned char *duart0_mcr = (unsigned char *)((ulong)DUART0_BA + 4);
- volatile unsigned char *duart1_mcr = (unsigned char *)((ulong)DUART1_BA + 4);
- volatile unsigned char *duart2_mcr = (unsigned char *)((ulong)DUART2_BA + 4);
- volatile unsigned char *duart3_mcr = (unsigned char *)((ulong)DUART3_BA + 4);
unsigned char *dst;
ulong len = sizeof(fpgadata);
int status;
/*
* Enable interrupts in exar duart mcr[3]
*/
- *duart0_mcr = 0x08;
- *duart1_mcr = 0x08;
- *duart2_mcr = 0x08;
- *duart3_mcr = 0x08;
+ out_8((void *)(DUART0_BA + 4), 0x08);
+ out_8((void *)(DUART1_BA + 4), 0x08);
+ out_8((void *)(DUART2_BA + 4), 0x08);
+ out_8((void *)(DUART3_BA + 4), 0x08);
return (0);
}
#include <common.h>
#include "canbt.h"
#include <asm/processor.h>
+#include <asm/io.h>
#include <command.h>
DECLARE_GLOBAL_DATA_PTR;
/*
* Setup port pins for normal operation
*/
- out32 (GPIO0_ODR, 0x00000000); /* no open drain pins */
- out32 (GPIO0_TCR, 0x07038100); /* setup for output */
- out32 (GPIO0_OR, 0x07030100); /* set output pins to high (default) */
+ out_be32 ((void *)GPIO0_ODR, 0x00000000); /* no open drain pins */
+ out_be32 ((void *)GPIO0_TCR, 0x07038100); /* setup for output */
+ out_be32 ((void *)GPIO0_OR, 0x07030100); /* set output pins to high (default) */
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
/*
* Check Board Identity:
*/
-
+#define LED_REG (CONFIG_SYS_PLD_BASE + 0x1000)
int checkboard (void)
{
char str[64];
int flashcnt;
int delay;
- volatile unsigned char *led_reg = (unsigned char *)((ulong)CONFIG_SYS_PLD_BASE + 0x1000);
- volatile unsigned char *ver_reg = (unsigned char *)((ulong)CONFIG_SYS_PLD_BASE + 0x1001);
puts ("Board: ");
puts(str);
}
- printf(" (PLD-Version=%02d)\n", *ver_reg);
+ printf(" (PLD-Version=%02d)\n",
+ in_8((void *)(CONFIG_SYS_PLD_BASE + 0x1001)));
/*
* Flash LEDs
*/
for (flashcnt = 0; flashcnt < 3; flashcnt++) {
- *led_reg = 0x00; /* LEDs off */
+ out_8((void *)LED_REG, 0x00); /* LEDs off */
for (delay = 0; delay < 100; delay++)
udelay(1000);
- *led_reg = 0x0f; /* LEDs on */
+ out_8((void *)LED_REG, 0x0f); /* LEDs on */
for (delay = 0; delay < 50; delay++)
udelay(1000);
}
- *led_reg = 0x70;
+ out_8((void *)LED_REG, 0x70);
return 0;
}
#include <common.h>
#include <asm/processor.h>
+#include <asm/io.h>
#include <command.h>
#include <malloc.h>
* Setup GPIO pins
*/
cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | ((CONFIG_SYS_EEPROM_WP | CONFIG_SYS_PB_LED | CONFIG_SYS_SELF_RST | CONFIG_SYS_INTA_FAKE) << 5));
+ mtdcr(cntrl0, cntrl0Reg |
+ ((CONFIG_SYS_EEPROM_WP | CONFIG_SYS_PB_LED |
+ CONFIG_SYS_SELF_RST | CONFIG_SYS_INTA_FAKE) << 5));
/* set output pins to high */
- out32(GPIO0_OR, CONFIG_SYS_EEPROM_WP);
+ out_be32((void *)GPIO0_OR, CONFIG_SYS_EEPROM_WP);
/* setup for output (LED=off) */
- out32(GPIO0_TCR, CONFIG_SYS_EEPROM_WP | CONFIG_SYS_PB_LED);
+ out_be32((void *)GPIO0_TCR, CONFIG_SYS_EEPROM_WP | CONFIG_SYS_PB_LED);
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
switch (state) {
case 1:
/* Enable write access, clear bit GPIO_SINT2. */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_EEPROM_WP);
+ out_be32((void *)GPIO0_OR,
+ in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_EEPROM_WP);
state = 0;
break;
case 0:
/* Disable write access, set bit GPIO_SINT2. */
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_EEPROM_WP);
+ out_be32((void *)GPIO0_OR,
+ in_be32((void *)GPIO0_OR) | CONFIG_SYS_EEPROM_WP);
state = 0;
break;
default:
/* Read current status back. */
- state = (0 == (in32(GPIO0_OR) & CONFIG_SYS_EEPROM_WP));
+ state = (0 == (in_be32((void *)GPIO0_OR) &
+ CONFIG_SYS_EEPROM_WP));
break;
}
}
* First pull fpga-prg pin low,
* to disable fpga logic (on version 2 board)
*/
- out32(GPIO0_ODR, 0x00000000); /* no open drain pins */
- out32(GPIO0_TCR, CONFIG_SYS_FPGA_PRG); /* setup for output */
- out32(GPIO0_OR, CONFIG_SYS_FPGA_PRG); /* set output pins to high */
- out32(GPIO0_OR, 0); /* pull prg low */
+ out_be32((void *)GPIO0_ODR, 0x00000000); /* no open drain pins */
+ out_be32((void *)GPIO0_TCR, CONFIG_SYS_FPGA_PRG); /* setup for output */
+ out_be32((void *)GPIO0_OR, CONFIG_SYS_FPGA_PRG); /* set output pins to high */
+ out_be32((void *)GPIO0_OR, 0); /* pull prg low */
/*
* Boot onboard FPGA
int board_early_init_f (void)
{
int index, len, i;
- volatile unsigned char dummy;
int status;
#ifdef FPGA_DEBUG
/*
* Init FPGA via RESET (read access on CS3)
*/
- dummy = *(unsigned char *) 0xf0200000;
+ in_8((void *)0xf0200000);
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
#include <common.h>
#include <command.h>
#include <pci.h>
+#include <asm/io.h>
#define OK 0
#define ERROR (-1)
/*
* Set EEPROM write-protect register to 0
*/
- out32 (pci9054_iobase + 0x0c,
- in32 (pci9054_iobase + 0x0c) & 0xffff00ff);
+ out_be32 ((void *)(pci9054_iobase + 0x0c),
+ in_be32 ((void *)(pci9054_iobase + 0x0c)) & 0xffff00ff);
/* Long Serial EEPROM Load Registers... */
val = PciEepromWriteLongVPD (0x00, 0x905410b5);
/*
* Set EEPROM write-protect register to 0
*/
- out32 (pci9054_iobase + 0x0c,
- in32 (pci9054_iobase + 0x0c) & 0xffff00ff);
+ out_be32 ((void *)(pci9054_iobase + 0x0c),
+ in_be32 ((void *)(pci9054_iobase + 0x0c)) & 0xffff00ff);
/* Long Serial EEPROM Load Registers... */
val = PciEepromWriteLongVPD (0x00, 0xffffffff);
#ifdef FPGA_DEBUG
printf ("%s\n",
- ((in32 (0x50000084) & 0x00010000) == 0) ? "NOT DONE" : "DONE");
+ ((in_be32 ((void *)0x50000084) & 0x00010000) == 0) ?
+ "NOT DONE" : "DONE");
#endif
/* init fpga by asserting and deasserting PROGRAM* (USER2)... */
#ifdef FPGA_DEBUG
printf ("%s\n",
- ((in32 (0x50000084) & 0x00010000) == 0) ? "NOT DONE" : "DONE");
+ ((in_be32 ((void *)0x50000084) & 0x00010000) == 0) ?
+ "NOT DONE" : "DONE");
#endif
/* cs1: disable burst, disable ready */
#ifdef FPGA_DEBUG
printf ("%s\n",
- ((in32 (0x50000084) & 0x00010000) == 0) ? "NOT DONE" : "DONE");
+ ((in_be32 ((void *)0x50000084) & 0x00010000) == 0) ?
+ "NOT DONE" : "DONE");
#endif
/* set cs1 to 32 bit data-width, disable burst, enable ready */
#ifdef FPGA_DEBUG
printf ("%s\n",
- ((in32 (0x50000084) & 0x00010000) == 0) ? "NOT DONE" : "DONE");
+ ((in_be32 ((void *)0x50000084) & 0x00010000) == 0) ?
+ "NOT DONE" : "DONE");
#endif
/* wait for 30 ms... */
#include <common.h>
#include <command.h>
-
+#include <asm/io.h>
#define EEPROM_CAP 0x50000358
#define EEPROM_DATA 0x5000035c
unsigned int eepromReadLong(int offs)
{
unsigned int value;
- volatile unsigned short ret;
+ unsigned short ret;
int count;
- *(unsigned short *)EEPROM_CAP = offs;
+ out_be16((void *)EEPROM_CAP, offs);
count = 0;
for (;;)
{
count++;
- ret = *(unsigned short *)EEPROM_CAP;
+ ret = in_be16((void *)EEPROM_CAP);
if ((ret & 0x8000) != 0)
break;
}
- value = *(unsigned long *)EEPROM_DATA;
+ value = in_be32((void *)EEPROM_DATA);
return value;
}
void eepromWriteLong(int offs, unsigned int value)
{
- volatile unsigned short ret;
+ unsigned short ret;
int count;
count = 0;
- *(unsigned long *)EEPROM_DATA = value;
- *(unsigned short *)EEPROM_CAP = 0x8000 + offs;
+ out_be32((void *)EEPROM_DATA, value);
+ out_be16((void *)EEPROM_CAP, 0x8000 + offs);
for (;;)
{
count++;
- ret = *(unsigned short *)EEPROM_CAP;
+ ret = in_be16((void *)EEPROM_CAP);
if ((ret & 0x8000) == 0)
break;
#include <common.h>
#include <asm/processor.h>
+#include <asm/io.h>
#include <command.h>
#include <malloc.h>
/*
* Reset CPLD via GPIO12 (CS3) pin
*/
- out32(GPIO0_OR, in32(GPIO0_OR) & ~(0x80000000 >> 12));
+ out_be32((void *)GPIO0_OR,
+ in_be32((void *)GPIO0_OR) & ~(0x80000000 >> 12));
udelay(1000); /* wait 1ms */
- out32(GPIO0_OR, in32(GPIO0_OR) | (0x80000000 >> 12));
+ out_be32((void *)GPIO0_OR,
+ in_be32((void *)GPIO0_OR) | (0x80000000 >> 12));
udelay(1000); /* wait 1ms */
return 0;
int i = getenv_r ("serial#", str, sizeof(str));
int flashcnt;
int delay;
- volatile unsigned char *led_reg = (unsigned char *)((ulong)CAN_BA + 0x1000);
+ u8 *led_reg = (u8 *)(CAN_BA + 0x1000);
puts ("Board: ");
puts(str);
}
- printf(" (PLD-Version=%02d)\n", *led_reg);
+ printf(" (PLD-Version=%02d)\n", in_8(led_reg));
/*
* Flash LEDs
*/
for (flashcnt = 0; flashcnt < 3; flashcnt++) {
- *led_reg = 0x40; /* LED_B..D off */
+ out_8(led_reg, 0x40); /* LED_B..D off */
for (delay = 0; delay < 100; delay++)
udelay(1000);
- *led_reg = 0x47; /* LED_B..D on */
+ out_8(led_reg, 0x47); /* LED_B..D on */
for (delay = 0; delay < 50; delay++)
udelay(1000);
}
- *led_reg = 0x40;
+ out_8(led_reg, 0x40);
return 0;
}
int misc_init_r (void)
{
- volatile unsigned char *duart0_mcr = (unsigned char *)((ulong)DUART0_BA + 4);
- volatile unsigned char *duart1_mcr = (unsigned char *)((ulong)DUART1_BA + 4);
- volatile unsigned char *duart2_mcr = (unsigned char *)((ulong)DUART2_BA + 4);
- volatile unsigned char *duart3_mcr = (unsigned char *)((ulong)DUART3_BA + 4);
unsigned char *dst;
ulong len = sizeof(fpgadata);
int status;
/*
* Reset external DUARTs
*/
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_DUART_RST); /* set reset to high */
+ out_be32((void *)GPIO0_OR,
+ in_be32((void *)GPIO0_OR) | CONFIG_SYS_DUART_RST);
udelay(10); /* wait 10us */
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_DUART_RST); /* set reset to low */
+ out_be32((void *)GPIO0_OR,
+ in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_DUART_RST);
udelay(1000); /* wait 1ms */
/*
* Enable interrupts in exar duart mcr[3]
*/
- *duart0_mcr = 0x08;
- *duart1_mcr = 0x08;
- *duart2_mcr = 0x08;
- *duart3_mcr = 0x08;
+ out_8((void *)(DUART0_BA + 4), 0x08);
+ out_8((void *)(DUART1_BA + 4), 0x08);
+ out_8((void *)(DUART2_BA + 4), 0x08);
+ out_8((void *)(DUART3_BA + 4), 0x08);
return (0);
}
projects / u-boot.git / commitdiff
