Quentin Schulz [Wed, 6 Nov 2024 11:29:43 +0000 (12:29 +0100)]
rockchip: tpl: allow to call board/SoC-specific code before DRAM init
This defines a weak tpl_board_init function that can be used for running
board/SoC-specific code before the DRAM init happens, similarly to
spl_board_init() for SPL.
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io> Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Quentin Schulz [Wed, 6 Nov 2024 11:29:42 +0000 (12:29 +0100)]
rockchip: rk3399: merge CRU check within rk3399_force_power_on_reset
To prepare to support forcing power on reset from TPL which would have
the exact same logic, just in an earlier stage, let's merge the CRU
check that triggers the power on reset with the rest of the logic.
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io> Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Fri, 1 Nov 2024 22:21:30 +0000 (22:21 +0000)]
board: rockchip: Add FriendlyElec NanoPi R2S Plus
The FriendlyElec NanoPi R2S Plus is a single-board computer based on
Rockchip RK3328 SoC. It features e.g. 1 GB DDR4 RAM, 32 GB eMMC,
SD-card, 2x GbE LAN, optional M.2 SDIO Wi-Fi and 2x USB 2.0 host.
Features tested on a NanoPi R2S Plus 2309:
- SD-card boot
- eMMC boot
- Ethernet
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
arm64: dts: rockchip: Add DTS for FriendlyARM NanoPi R2S Plus
The R2S Plus is basically an R2S with additional eMMC.
The eMMC configuration for the DTS has been extracted and copied from
rk3328-nanopi-r2.dts, v2017.09 branch from the friendlyarm/uboot-rockchip
repository.
(cherry picked from commit c9bf98827964441f4dd16faa45bd4046f472e693) Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Andy Yan [Mon, 4 Nov 2024 12:23:00 +0000 (20:23 +0800)]
board: rockchip: Add support for rk3588 GenBook
Add support for Cool Pi GenBook, it works as a carrier board
connect with CM5 SOM.
Specification:
- Rockchip RK3588
- LPDDR5X 8/32 GB
- eMMC 64 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for RTL8852BE Wireless connection
- PCIE M.2 M Key for NVME connection
- eDP panel with 1920x1080
Tested by Armbian boot on USB disk.
Change-Id: I4d9b8572dc7c400077dde666633f3fea1b47dd03 Signed-off-by: Andy Yan <andyshrk@163.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Andy Yan [Mon, 4 Nov 2024 12:22:59 +0000 (20:22 +0800)]
rockchip: Make it possible to define per board boot_targets
Some board may want to have a different boot priority(a laptop
may want to usb has the highest boot priority for third-part
os installation). So let the board can define it's own
boot_targets.
Signed-off-by: Andy Yan <andyshrk@163.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Andy Yan [Mon, 4 Nov 2024 12:22:58 +0000 (20:22 +0800)]
arm64: dts: rockchip: Add support for rk3588 based Cool Pi CM5 GenBook
Cool Pi CM5 GenBook works as a carrier board connect with CM5 [0].
Specification:
- Rockchip RK3588
- LPDDR5X 8/32 GB
- eMMC 64 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for RTL8852BE Wireless connection
- PCIE M.2 M Key for NVME connection
- eDP panel with 1920x1080
This patch add basic support to bringup eMMC/USB HOST/WiFi/TouchPad/
Battery/PCIE NVME, and can also drive a HDMI output with out of tree
hdmi patches.
Heiko Stuebner [Mon, 28 Oct 2024 19:00:34 +0000 (20:00 +0100)]
board: rockchip: add support for Qnap TS433 devices
The Qnap TS433 is a 4-bay NAS based around the RK3568.
Two SATA bays are connected to the RK3568's own SATA controllers while
the other two are connected to a JMicron SATA controller living on the
PCIe bus.
It provides one 2.5Gb and one 1Gb ethernet port as well as 3 usb ports.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Heiko Stuebner [Mon, 28 Oct 2024 19:00:33 +0000 (20:00 +0100)]
arm64: dts: rockchip: add product-data eeproms to QNAP TS433
The device contains two i2c-connected eeproms holding some product-
specific values. One sitting on the mainboard and one on the statically
connected backplane.
While the eeprom chips themself have a size of 512 byte, the eeprom data
only uses 256 byte each, probably to stay compatible with other models.
Heiko Stuebner [Mon, 28 Oct 2024 19:00:32 +0000 (20:00 +0100)]
arm64: dts: rockchip: actually enable pmu-io-domains on qnap-ts433
Contrary to the vendor-kernel the pmu-io-domains are not enabled by
default. This resulted in the value not being set according to the
regulator, which in turn made the gmac0 interface that is connected
to the vccio4 supply inoperable.
Uwe Kleine-König [Mon, 28 Oct 2024 19:00:31 +0000 (20:00 +0100)]
arm64: dts: rockchip: Simplify network PHY connection on qnap-ts433
While it requires to have the right phy driver loaded (i.e. motorcomm)
to make the phy asserting the right delays, this is generally the
preferred way to define the MAC <-> PHY connection.
Heiko Stuebner [Mon, 28 Oct 2024 19:00:28 +0000 (20:00 +0100)]
arm64: dts: rockchip: add missing pmic information on Qnap-TS433
Fill in the missing pieces for RK809 pmic used on the TS433.
The regulator setup comes from the vendor-devicetree, so without proper
schematics its accuracy is somewhat unclear, but it looks really similar
to all the other rk3568 boards, so follows the reference design it seems.
The one caveat is related to vcc3v3_sd. This regulator needs to stay on.
When turned off because of no users, access to both PCIe controllers
will stall. Maybe this rail does supply the 100MHz refclk generation
or so.
Heiko Stuebner [Mon, 28 Oct 2024 19:00:27 +0000 (20:00 +0100)]
arm64: dts: rockchip: define cpu-supply on the Qnap-TS433
The TS433 seems to use a silergy,syr827 regulator for the cpu supply.
At least that is the compatible used in the vendor devicetree, though
it could very well also be another fan53555 clone.
Define the needed regulator node and hook up the cpu-supply to the
cpu cores.
Heiko Stuebner [Mon, 28 Oct 2024 19:00:26 +0000 (20:00 +0100)]
arm64: dts: rockchip: add gpio-keys to Qnap-TS433
The TS433 has 3 buttons, power and copy in the front as well as a reset
pinhole button on the back. The power-button is connected to the embedded
controller while the other two buttons are just gpio connected.
Add the gpio-keys definition for the two buttons we can handle right now.
Heiko Stuebner [Mon, 28 Oct 2024 19:00:23 +0000 (20:00 +0100)]
arm64: dts: rockchip: add board-aliases for Qnap-TS433
Add the aliases for the internal network interface as well as the emmc
on the board and make sure the dedicated RTC is always the first one.
The TS433 actually has two rtc devices. One coming from the rk809 pmic
without added functionality and also a dedicated RTC from Mycrocrystal
that is battery backed to keep the time.
Heiko Stuebner [Mon, 28 Oct 2024 19:00:22 +0000 (20:00 +0100)]
arm64: dts: rockchip: enable sata1+2 on Qnap-TS433
The TS433 has 4 bays. The last two are accessed via a pci-connected
sata controller, while the first two are accessed via the rk3568's
sata controllers. Enable these two now.
Heiko Stuebner [Mon, 28 Oct 2024 19:00:18 +0000 (20:00 +0100)]
arm64: dts: rockchip: enable second PCIe controller on the Qnap-TS433
The TS433 uses both pcie controllers for sata and the 2nd network
interface. Set the needed data-lanes in the pcie3 phy and enable
the second pcie controller, as well as remove the bifurcation comment.
Yuri Zaporozhets [Wed, 30 Oct 2024 19:38:20 +0000 (20:38 +0100)]
bios_emulator: fix first argument of pci_{read,write}_config_* function calls
When compiling for riscv64, a bunch of warning is produced for the file
drivers/bios_emulator/besys.c. This patch fixes a portion of those warnings,
caused by incorrect first argument to pci_{read,write}_config_* functions.
Yuri Zaporozhets [Wed, 30 Oct 2024 13:00:51 +0000 (14:00 +0100)]
bios_emulator: define the comment symbol for RISC-V assembler too
The bios_emulator driver cannot be compiled for RISC-V because the x86emu.h
header file doesn't define the comment symbol ("#") for the assembler.
With this patch, use the same symbol as for e.g. x86.
Weijie Gao [Tue, 29 Oct 2024 09:47:16 +0000 (17:47 +0800)]
menu: add support to check if menu needs to be reprinted
This patch adds a new callback named need_reprint for menu.
The need_reprint will be called before printing the menu. If the
callback exists and returns FALSE, menu printing will be canceled.
This is very useful if the menu was not changed. It can save time
for serial-based menu to handle more input data.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Reviewed-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Daniel Golle <daniel@makrotopia.org>
Weijie Gao [Tue, 29 Oct 2024 09:47:10 +0000 (17:47 +0800)]
menu: fix the logic checking whether ESC key is pressed
It's observed that the bootmenu on a serial console sometimes
incorrectly quitted with superfluous characters filled to command
line input:
> *** U-Boot Boot Menu ***
>
> 1. Startup system (Default)
> 2. Upgrade firmware
> 3. Upgrade ATF BL2
> 4. Upgrade ATF FIP
> 5. Load image
> 0. U-Boot console
>
>
> Press UP/DOWN to move, ENTER to select, ESC to quit
>MT7988> [B
Analysis shows it was caused by the wrong logic of bootmenu_loop:
At first the bootmenu_loop received the first ESC char correctly.
However, during the second call to bootmenu_loop, there's no data
in the UART Rx FIFO. Due to the low baudrate, the second char of
the down array key sequence hasn't be fully received.
But bootmenu_loop just did a mdelay(10), and then treated it as a
single ESC key press event. It didn't even try tstc() again after
the 10ms timeout.
This patch fixes this issue by letting bootmenu_loop check tstc()
twice.
Tested-By: E Shattow <lucent@gmail.com> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com> Reviewed-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Daniel Golle <daniel@makrotopia.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 4 Nov 2024 21:40:54 +0000 (15:40 -0600)]
Merge patch series "U-boot: arm: Refine the booting on Total Compute"
Leo Yan <leo.yan@arm.com> says:
This patch series is to refine the booting on Arm Total Compuate
platform.
It changes to use the info passed in DTB for initialization DRAM info,
and dynamically initializes the booting envoironment variables.
Another big change is to use an envoironment file for boot commands,
based on it, the series extends to support multiple block devices
(MMC and virtio). And the env file is extended for booting Debian.
The last commit is to update memory mapping info based on the DRAM info
passed via DT binding.
Leo Yan [Fri, 25 Oct 2024 17:18:21 +0000 (18:18 +0100)]
arm: total_compute: Update memory mapping info
This commit introduces build_mem_map() function for updating the mem_map
structure with copying info from gd->bd->bi_dram, so that it can keep
the consistence for DRAM info passed via DT.
The page table size is calculated prior to mem_map is ready, introduce
the get_page_table_size() function for a predefined table size.
Initialize the environment variables 'fdt_addr_r' and 'kernel_addr_r'
during the misc init phase. The static configurations are not needed,
remove them.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com> Signed-off-by: Leo Yan <leo.yan@arm.com>
Boyan Karatotev [Fri, 25 Oct 2024 17:18:14 +0000 (18:18 +0100)]
arm: total_compute: depend on TF-A for hardware description
On Total Compute, TF-A passes the info via DT binding for the hardware
description - includes the serial, memory, and arm_ffa nodes.
This commit initializes the fdt base address based on the passed the
register x1.
The similar implementation has already been done for the raspberry pi,
so borrow a lot of it.
Co-developed-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com> Signed-off-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com> Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com> Signed-off-by: Leo Yan <leo.yan@arm.com>
Tom Rini [Mon, 4 Nov 2024 20:49:10 +0000 (14:49 -0600)]
Merge patch series "Fixes to allow 'ut bootm' to pass when run interactively"
Andrew Goodbody <andrew.goodbody@linaro.org> says:
Starting a sandbox session and running 'ut bootm' on the command
line instead of using pytest with --verbose will result in some
test failures. This series makes the tests more deterministic so
that they will better control their environment and hence will
work as expected whether or not they are invoked with '--verbose'.
The series starts with a small fix to the parameters of
bootm_process_cmdline that one commit incorrectly added using a bool
when it had been updated to take flags by the preceeding commit.
Andrew Goodbody [Fri, 1 Nov 2024 13:02:54 +0000 (13:02 +0000)]
test: bootm: Ensure GD_FLG_SILENT is reset
Some bootm tests expect that GD_FLG_SILENT is reset in order
to work as expected. This is the state if the test is run with
'pytest --verbose' but not if run from, say, the sandbox command
line.
So reset the flag for those tests that rely on it being reset. This
has to be done in each test as the test infrastructure will set it
again before every test when not invoked with 'pytest --verbose'.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
The function bootm_process_cmdline_env takes flags as its third
parameter, not a bool. Correct the usage by replacing 'true'
with BOOTM_CL_ALL so that the intent is clear.
A similar change was made throughtout this file in the previous
commit to the one mentioned below as being fixed.
Fixes: 4448fe8e4e7c ("bootm: Allow updating the bootargs in a buffer") Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Andrew Goodbody [Tue, 15 Oct 2024 14:17:37 +0000 (15:17 +0100)]
usb: Fix test dependency on ext4write command
The tests test_usb_ext4load_ext4write, test_usb_ext2load and
test_usb_load depend on the command ext4write being present not just
the feature of being able to write to an ext4 file system. So update
their dependencies to include the ext4write command itself. This will
prevent spurious test failures when running the USB tests against USB
storage with an ext2/ext4 partition but no ext4write command available.
Fixes: 1c5b6edad381 ("test/py: usb: Add tests for USB device") Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org> Reviewed-by: Love Kumar <love.kumar@amd.com>
Andrew Goodbody [Tue, 15 Oct 2024 12:19:16 +0000 (13:19 +0100)]
usb: Fix test failure with multiple partitions
When test_usb_load finds multiple partitions of the same type then
it will cause a test failure. The call to write the test file will
write a different test file to each partition but only return the
name and size of the last one written. So the test then fails to
load the test file from the first partition as it uses the name of
a file on a different partition.
Refactor the code so that only one test file is written at a time
and is written to only the partition being tested at that time. This
allows the correct file name to always be available to the code that
runs the load command. This reduces the number of files written and
also the number of calls to crc32 needed.
Fixes: 1c5b6edad381 ("test/py: usb: Add tests for USB device") Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org> Reviewed-by: Love Kumar <love.kumar@amd.com>
Simon Glass [Mon, 28 Oct 2024 12:47:53 +0000 (13:47 +0100)]
test: Allow saving and restoring the bloblist
Tests which create a new bloblist overwrite the existing one in sandbox.
Provide a flag for tests to declare this behaviour. Save and restore the
bloblist pointer so that other tests remain unaffected.
Note that when sandbox is running normally, the bloblist has been
relocated to high in memory. The existing bloblist tests create a new
bloblist low in memory, so they do not conflict.
Correct a build error on coreboot by using accessors for gd->bloblist: Signed-off-by: Simon Glass <sjg@chromium.org>
Jonas Karlman [Sat, 3 Aug 2024 12:41:45 +0000 (12:41 +0000)]
bootstage: Do not sort records
The timer counter on Rockchip SoCs may be reset in TF-A, this may cause
the bootstage records to be printed out of order and with an incorrect
elapsed time.
For the tested board external TPL and BROM take ~164 ms to initialize
DRAM and load SPL, SPL take ~210ms to load images from FIT and U-Boot
proper take ~477ms to reach cli prompt.
Simon Glass [Sat, 19 Oct 2024 15:21:56 +0000 (09:21 -0600)]
test: Expand implementation of ut_list_has_dm_tests()
This function assumes that all tests in a suite are being run. This
means that it can sometimes call dm_test_restore() when it should not.
The impact of this is that it is not possible, for example, to run
'ut bootstd bootflow_cros' and then check the state of bootstd
afterwards, since all devices are removed and recreated.
Update the function to take account of any selected test, to avoid this
problem.
Simon Glass [Sat, 19 Oct 2024 15:21:50 +0000 (09:21 -0600)]
test: boot: Use a consistent name for the script bootmeth
In the bootflow tests the script bootmeth is bound with the name
bootmeth_script whereas the others have a name without the bootmeth_
prefix. Adjust it to be the same.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Simon Glass [Sat, 19 Oct 2024 15:21:47 +0000 (09:21 -0600)]
alist: Add a way to efficiently filter an alist
Unlike linked lists, it is inefficient to remove items from an alist,
particularly if it is large. If most items need to be removed, then the
time-complexity approaches O(n2).
Provide a way to do this efficiently, by working through the alist once
and copying elements down.
Marek Vasut [Sun, 27 Oct 2024 02:20:07 +0000 (03:20 +0100)]
ARM: renesas: Deduplicate common Renesas defconfig
Deduplicate common Renesas defconfig by factoring out the common
parts into generic renesas_rcar_defconfig and including those using
the #include <configs/...> preprocessor macro in the current set of
board specific defconfigs. The preprocessor macro is applicable
to defconfigs as well.
This introduces no functional change, the resulting .config are
identical for all Renesas systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Deduplicate defconfigs for all Renesas R-Car 64bit systems by factoring
out the common parts into generic renesas_rcar64.config and including
those using the #include <configs/...> preprocessor macro in the current
set of board specific defconfigs. The preprocessor macro is applicable
to defconfigs as well.
This introduces no functional change, the resulting .config is identical
for all Renesas R-Car 64bit systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Deduplicate defconfigs for all Renesas R-Car Gen4 systems by factoring
out the common parts into generic renesas_rcar4.config and including
those using the #include <configs/...> preprocessor macro in the current
set of board specific defconfigs. The preprocessor macro is applicable
to defconfigs as well.
This introduces no functional change, the resulting .config is identical
for all Renesas R-Car Gen4 systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Deduplicate defconfigs for all Renesas R-Car Gen3 systems by factoring
out the common parts into generic renesas_rcar3.config and including
those using the #include <configs/...> preprocessor macro in the current
set of board specific defconfigs. The preprocessor macro is applicable
to defconfigs as well.
This introduces no functional change, the resulting .config is identical
for all Renesas R-Car Gen3 systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Deduplicate defconfigs for all Renesas R-Car Gen2 systems by factoring
out the common parts into generic renesas_rcar2.config and including
those using the #include <configs/...> preprocessor macro in the current
set of board specific defconfigs. The preprocessor macro is applicable
to defconfigs as well.
This introduces no functional change, the resulting .config is identical
for all Renesas R-Car Gen2 systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Wed, 4 Sep 2024 22:34:20 +0000 (00:34 +0200)]
clk: renesas: Fix missing unbind on driver look up failure
In case lists_driver_lookup_name("rst_gen3") fails, the clk_gen3 driver
has to be unbound before erroring out. Reorder the function such that
both clk_gen3 and rst_gen3 drivers are looked up first, if either look
up fails then the function errors out right away. Second, the clk_gen3
is bound, if binding fails, the function still errors out right away
because there is nothing to undo after either lists_driver_lookup_name()
call. Finally, rst_gen3 is bound and if this binding fails, then that
is the only place where clk_gen3 has to be unbound before erroring out.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tom Rini [Fri, 1 Nov 2024 19:38:05 +0000 (13:38 -0600)]
Merge patch series "fs: ext4: implement opendir, readdir, closedir"
Heinrich Schuchardt <heinrich.schuchardt@canonical.com> says:
With this series opendir, readdir, closedir are implemented for ext4.
These functions are needed for the UEFI sub-system to interact with
the ext4 file system.
To reduce code growth the functions are reused to implement the ls
command for ext4.
A memory leak in ext4fs_exists is resolved.
ext4fs_iterate_dir is simplified by removing a redundant pointer copy.
Now that opendir, readir, closedir are implemented for ext4 we can use
fs_ls_generic() for implementing the ls command.
Adjust the unit tests:
* fs_ls_generic() produces more spaces between file size and name.
* The ext4 specific message "** Can not find directory. **\n" is not
written anymore.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Some of our file system drivers cannot report a file size for
directories. Use a dummy value in this case.
* For SetInfo the UEFI spec requires to ignore the file size field.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 30 Oct 2024 00:36:49 +0000 (18:36 -0600)]
test/cmd/mem_copy.c: Use CONFIG_SYS_LOAD_ADDR for base
When reading/writing to memory we cannot assume that a base address of
0x0 is correct and functional. So use CONFIG_SYS_LOAD_ADDR as the base
from which we add a bit more padding and being our tests.
Patrick Rudolph [Wed, 30 Oct 2024 13:11:46 +0000 (14:11 +0100)]
acpi_table: Fix coverity defect in acpi_write_spcr
Fix "Integer handling issues (SIGN_EXTENSION)" in newly added code:
Cast serial_info.reg_offset to u64 to prevent an integer overflow when
shifted too many bits to the left. Currently this never happens as the
shift is supposed to be less than 4.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tom Rini [Thu, 31 Oct 2024 17:47:25 +0000 (11:47 -0600)]
mtd: spi-nor: Guard SPI_STACKED_PARALLEL with DM_SPI check
While we want to compile the SPI_STACKED_PARALLEL code everywhere we
can, it must first be guarded with an #if for DM_SPI as not all cases
where we have this code built, such as in SPL, will have the relevant
DM_SPI option enabled.
Fixes: 43423cdc5dc1 ("mtd: spi-nor: Always build SPI_STACKED_PARALLEL code") Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Tom Rini <trini@konsulko.com>
In the patch series "spi-nor: Add parallel and stacked memories support"
a number of issues have since been raised about problems that now exist
on a large number of previously working platforms. Marek Vasut has gone
and identified a number of issues and this series is the starting point
of attempting to address them and fix the problems with previously
existing platforms.
Prevent the code gated by SPI_STACKED_PARALLEL from bitrot
by using if (CONFIG_IS_ENABLED(SPI_STACKED_PARALLEL)) around
it. That way, it is always at least compiled.
Fixes: 5d40b3d384dc ("mtd: spi-nor: Add parallel and stacked memories support") Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Sat, 26 Oct 2024 20:16:25 +0000 (22:16 +0200)]
mtd: spi-nor: Rename SPI_ADVANCE to SPI_STACKED_PARALLEL
The SPI_ADVANCE description does not explain what the switch does.
It does not have anything to do with any advanced functionality, it
only gates off support for stacked and parallel SPI NORs. Rename the
Kconfig symbol, update description, and move it right next to Xilinx
hardware as it seems to be specific to this hardware. Make sure the
symbol is also protected by if DM_SPI in Kconfig.
Fixes: 5d40b3d384dc ("mtd: spi-nor: Add parallel and stacked memories support") Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Sat, 26 Oct 2024 20:16:24 +0000 (22:16 +0200)]
mtd: spi-nor: Rewrite rem_bank_len calculation
Rewrite the code to make it clear exactly where the
SNOR_F_HAS_PARALLEL flag leads to *2 and /2 operation
compared to regular code path. No functional change.
Fixes: 5d40b3d384dc ("mtd: spi-nor: Add parallel and stacked memories support") Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
projects / u-boot.git / log