From e25d5a95e7ff45b18e3d9dfac24efd35377abf53 Mon Sep 17 00:00:00 2001
From: Stefan Roese <sr@denx.de>
Date: Thu, 10 Dec 2015 10:32:36 +0100
Subject: [PATCH] arm: mvebu: Make serdes setup on Armada XP less noisy
Change some of the PEX configuration output lines from always output to
only ouput upon specific debug enabling.
This changes the SPL output from:
U-Boot SPL 2016.01-rc2-00037-g9353a7f (Dec 10 2015 - 10:27:42)
High speed PHY - Version: 2.1.5 (COM-PHY-V20)
Update Device ID PEX0782611ab
Update Device ID PEX1782611ab
Update Device ID PEX2782611ab
Update Device ID PEX3782611ab
Update Device ID PEX8782611ab
Update PEX Device ID 0x78260
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.4
DDR3 Training Sequence - Ended Successfully
to:
U-Boot SPL 2016.01-rc2-00037-g9353a7f-dirty (Dec 10 2015 - 10:32:04)
High speed PHY - Version: 2.1.5 (COM-PHY-V20)
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.4
DDR3 Training Sequence - Ended Successfully
Resulting in a little faster bootup time.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
.../arm/mach-mvebu/serdes/axp/high_speed_env_lib.c | 14 +++++++-------
1 file changed, 7 insertions(+), 7 deletions(-)
diff --git a/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c b/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c
index 976297119f..bfa7f136c3 100644
--- a/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c
+++ b/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c
@@ -1376,19 +1376,19 @@ int serdes_phy_config(void)
pex_if, PEX_DEVICE_AND_VENDOR_ID));
devId &= 0xFFFF;
devId |= ((ctrl_mode << 16) & 0xffff0000);
- DEBUG_INIT_S("Update Device ID PEX");
- DEBUG_INIT_D(pex_if, 1);
- DEBUG_INIT_D(devId, 8);
- DEBUG_INIT_S("\n");
+ DEBUG_INIT_FULL_S("Update Device ID PEX");
+ DEBUG_INIT_FULL_D(pex_if, 1);
+ DEBUG_INIT_FULL_D(devId, 8);
+ DEBUG_INIT_FULL_S("\n");
reg_write(PEX_CFG_DIRECT_ACCESS
(pex_if, PEX_DEVICE_AND_VENDOR_ID), devId);
if ((pex_if < 8) &&
(info->pex_mode[pex_unit] == PEX_BUS_MODE_X4))
pex_if += 3;
}
- DEBUG_INIT_S("Update PEX Device ID 0x");
- DEBUG_INIT_D(ctrl_mode, 4);
- DEBUG_INIT_S("0\n");
+ DEBUG_INIT_FULL_S("Update PEX Device ID 0x");
+ DEBUG_INIT_FULL_D(ctrl_mode, 4);
+ DEBUG_INIT_FULL_S("0\n");
}
tmp = reg_read(PEX_DBG_STATUS_REG(0));
DEBUG_RD_REG(PEX_DBG_STATUS_REG(0), tmp);
--
2.39.5