Mike Looijmans [Fri, 18 Jan 2019 08:02:48 +0000 (09:02 +0100)]
board: topic-miamiplus: Run IO PLL at 1000 MHz
The miamiplus can use GEM0 through MIO pins, which requires a 125 MHz TX
clock to be generated. With the IO PLL at 1200 MHz this isn't possible, so
change it to run at 1000 and adjust the divisors accordingly. Also set the
GEM0 clock source to MIO instead of EMIO.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mike Looijmans [Fri, 18 Jan 2019 08:02:47 +0000 (09:02 +0100)]
topic-miamiplus: Run CPU at 800MHz for speedgrade-2
The miamiplus contains a speedgrade-2 device, which may run the CPU at 800MHz.
Change the PLL setting to 800MHz, and adapt the setpoints in the devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 18 Jan 2019 09:43:39 +0000 (10:43 +0100)]
i2c: cdns: Convert to livetree function
Update cadence i2c driver to support livetree
Similar changes were done by:
"net: zynq_gem: convert to use livetree"
(sha1: 26026e695afa794ac018a09e79a48120d322b60d)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables CONFIG_REMAKE_ELF for Zynq platform
so that it generates u-boot.elf from binary which works
for all Zynq boards with OF_SEPARATE option enabled.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 16 Jan 2019 11:14:00 +0000 (12:14 +0100)]
arm64: zynqmp: Align u-boot-spl.bin for boot.bin creation
Bootrom is not capable to work with non align bootloader partition
that's why it is necessary to align it before boot.bin creation.
The patch is creating new spl/u-boot-spl-align.bin which is used only
for boot.bin.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bootrom is not capable to work with non aligned bootloader sizes.
SPL with OF_SEPARATE generates non-align images quite often that's
why this change is required before OF_SEPARATE enableding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 15 Jan 2019 09:45:41 +0000 (10:45 +0100)]
arm64: zynqmp: Enable ISSI flash for some platforms
Enable ISSI flash for platforms. Xilinx reference boards are also used
internally with different flash part to increase coverage that's why
enable also ISSI parts for all these boards even if that board is
released only with one part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: zynqmp: Fix mmc node names to be in sync with kernel
This patches renames sd nodes in dts to be in line with
kernel. This patch also modifies the references for the same
in code.
It checks mmc first to have no time penalty for new DT node names based
on left-to-right expression evaluation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Stefan Theil [Mon, 17 Dec 2018 08:12:30 +0000 (09:12 +0100)]
zynq-gem: Use appropriate cache flush/invalidate for RX and TX
The cache was only flushed before *transmitting* packets, but not
when receiving them, leading to an issue where new packets were
handed to the receive handler with old contents in cache. This
only happens when a lot of packets are received without sending
packages every now and then. Also flushing the receive buffers
in the transmit function makes no sense and can be removed.
Signed-off-by: Stefan Theil <stefan.theil@mixed-mode.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 20 Dec 2018 08:41:12 +0000 (09:41 +0100)]
arm64: zynqmp: Do not protect zynqmp_pmufw_version()
There is hard dependency for CLK_ZYNQMP to have zynqmp_pmufw_version()
but also FPGA code is calling this function which is possible to use
without actual CLK_ZYNQMP firmware driver to be enabled.
This patch enables the case where only fixed-clock CLK setup is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 5 Dec 2018 11:40:55 +0000 (12:40 +0100)]
mmc: zynq: Remove unused pwrseq variable
This variable was incorrectly added by:
"mmc: zynq_sdhci: Add support for SD3.0"
(sha1: d1f4e39d58db32a4fd1a1b4085e0ede498bd773f)
which had nothing to do with MMC power sequence provider.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michael Tretter [Mon, 3 Dec 2018 15:37:53 +0000 (16:37 +0100)]
tools: zynqmpimage: round up partition size
The FSBL copies "Total Partition Word Length" * 4 bytes from the boot.bin,
which implies that the partition size is 4 byte aligned. When writing the
partition, mkimage calculates "Total Partition Word Length" by dividing
the size by 4. This implicitly cuts unaligned bytes at the end of the
added binary.
Instead of rounding down, the size must be round up to 4 bytes and the
binary padded accordingly.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de> Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Wed, 23 Jan 2019 22:24:31 +0000 (17:24 -0500)]
Merge tag 'mips-pull-2019-01-23' of git://git.denx.de/u-boot-mips
- MIPS: mscc: ocelot: add ethernet switch and network support
- MIPS: mscc: add support for ServalT SoC family
- MIPS: mscc: add support for Serval SoC family
ftsdc010_mci's compatible has been modified as
"andestech,atfsdc010" for RISC-V synchronization.
But ae3xx.dts and ag101p.dts which are used for
nds32 adp-ae3xx and adp-ag101p platforms did not
be modified correctly at that time. It will cause
mmc detection failure. Fix it here.
Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com>
Tom Rini [Mon, 21 Jan 2019 16:59:21 +0000 (11:59 -0500)]
Merge git://git.denx.de/u-boot-marvell
- Sync Armada-38x dts with Linux 4.20 from Chris
- Misc changes and enhancements to Turris Mox (v4) from Marek
- Reserve PSCI area for Armada 8k from Heinrich
- New Allied Telesis x530 board (Armada-385) from Chris
- Misc minor changes (defconfig etc)
[Mailing List Thread]
https://lists.denx.de/pipermail/u-boot/2018-December/350666.html
Fixes: 5541543f ("configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignment")
[trini: Make the migration be size neutral and possibly not fix the
above in all cases] Reported-by: Daniel Evans <photonthunder@gmail.com> Cc: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Derald D. Woods <woods.technical@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Chris Packham [Thu, 10 Jan 2019 08:01:00 +0000 (21:01 +1300)]
ARM: mvebu: add support for Allied Telesis x530
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Baruch Siach [Wed, 2 Jan 2019 16:26:42 +0000 (18:26 +0200)]
board: mvebu: drop unused ETH_PHY macro definitions
These macros are not used anywhere in the boards code.
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Dennis Gilmore <dgilmore@redhat.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
An NVME drive may be installed on the MACCHIATObin board using the PCIe
slot or on the Clearfog Pro using mini a PCI-e slot. With the configuration
change it becomes usable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 17 Dec 2018 15:10:08 +0000 (16:10 +0100)]
arm: mvebu: turris_mox: Read info (and ethaddrs) from OTP
Add support for reading One-Time Programmable memory via mailbox, which
communicates with CZ.NIC's firmware on the Secure Processor (Cortex-M3)
of Armada 3720.
Display product serial number and additional info, and also set MAC
addresses.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 17 Dec 2018 15:10:06 +0000 (16:10 +0100)]
watchdog: armada_37xx: Fix compliance with kernel's driver
The Armada 37xx watchdog driver was recently accepted for mainline
kernel by watchdog subsystem maintainer, but the driver works a little
different than the one in U-Boot. This patch fixes this.
In the previous implementation there was a tiny period of time when the
watchdog was disabled and the system was vulnerables - this was during
pinging, which was done by disabling, setting, and enabling the counter.
Now pinging is done without disabling the watchdog. We use 2 counters:
Counter 1 is the watchdog counter - on expiry, the system is reset.
Counter 0 is used to reset Counter 1 to start counting from the set
timeout again. So Counter 1 is set to be reset on Counter 0 expiry event
event and pinging is done by forcing an immediate expiry event on
Counter 0.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 17 Dec 2018 15:10:05 +0000 (16:10 +0100)]
arm: mvebu: turris_mox: Update defconfig
Add gpio command to defconfig - this can be used to detect whether the
button is pressed or light LEDs.
Add DS1307 RTC driver and the date command.
Add CONFIG_WATCHDOG, so that U-Boot calls watchdog_reset.
Add CONFIG_MISC_INIT_R so that ethernet addresses are read from OTP
before network controller is initialized.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 17 Dec 2018 15:10:04 +0000 (16:10 +0100)]
arm: mvebu: dts: Fix Turris Mox device tree
DTC issues a warning because #address-cells and #size-cells properties
are not set in the mdio node.
Also add ethernet1 alias.
Also add RTC node.
Also fix USB3 regulator startup delay time.
Also fix PCI Express SERDES speed to 5 GHz (this is only cosmetic, the
speed value is not used byt the comphy driver for PCI Express, but
should be 5 GHz nonetheless).
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Mon, 10 Dec 2018 07:07:51 +0000 (20:07 +1300)]
ARM: mvebu: sync Armada-38x dts with Linux 4.20
Sync the Armada-38x device tree files with Linux 4.20-rc5. The changes
not taken are new compatible strings for the uart and nand flash
controller. The nand binding is best updated if/when the mtd/nand
infrastructure is updated.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Joakim Tjernlund [Wed, 28 Nov 2018 09:59:55 +0000 (10:59 +0100)]
mpc83xx: Add support for -msingle-pic-base
-msingle-pic-base is a new gcc(from 4.6) option for ppc and
it reduces the size of my u-boot with about 4 KB.
While at it, add -fno-jump-tables too to save a
few more bytes.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Reviewed-by: Mario Six <mario.six@gdsys.cc> Tested-by: Mario Six <mario.six@gdsys.cc> (on MPC8308)
Philipp Tomsich [Fri, 30 Nov 2018 21:13:25 +0000 (22:13 +0100)]
Kconfig: Migrate BOUNCE_BUFFER
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.
This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).
This commit includes a full migration using moveconfig.py to ensure
that each commit compiles. To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.
[trini: Squash all patches to ensure bisectability] Signed-off-by: Tom Rini <trini@konsulko.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion] Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion] Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
Tom Rini [Fri, 18 Jan 2019 18:40:41 +0000 (13:40 -0500)]
Merge branch '2019-01-18-master-imports'
- Bugfix for SPI environment optimization
- Spelling fixes
- Remove some defconfigs per various maintainers
- Minor db410, bananapi r2 fixes
- Bump QEMU to v3.1.0 for most platforms
breaks Environment functionality, as it reads only
until 2 \0 are found, but fills the buffer with 0x0
instead 0xff which leads in an incorrect crc sum.
Quentin Schulz [Thu, 17 Jan 2019 09:18:47 +0000 (10:18 +0100)]
cmd: mtd: fix compilation warning for help when SYS_LONGHELP=n
cmd/mtd.c:447:13: warning: ‘mtd_help_text’ defined but not used [-Wunused-variable]
static char mtd_help_text[] =
^~~~~~~~~~~~~
When SYS_LONGHELP is not defined. After looking at how other commands
work, we should surround the whole help text (even its declaration) with
an #ifdef CONFIG_SYS_LONGHELP, since it's compiled out when calling
_CMD_HELP[1] on the help text variable argument to U_BOOT_CMD.
Michal Simek [Wed, 16 Jan 2019 14:18:44 +0000 (15:18 +0100)]
travis: Switch QEMU to 3.1.0 version
Vexpress ca15_tc2 is failing with 3.1.0 because of QEMU issue.
When this patch is applied
https://patchwork.kernel.org/patch/10754401/
Vexpress can be also turn to newer QEMU version.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Michal Simek [Wed, 16 Jan 2019 14:18:43 +0000 (15:18 +0100)]
travis: Setup QEMU_VERSION as variable
This change enables setting up specific Qemu version or sha1 for new
targets which are added after (current) v3.0.0 version.
This changes is preparation step for adding new Xilinx Versal Virt
platform which was merge after v3.0.0.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 16 Jan 2019 12:19:26 +0000 (07:19 -0500)]
travis: Break up the NXP Layerscape jobs more
The single job for all Layerscape 10xx platforms is close to, and
sometimes exceeds the time limit for a single job configuration. Break
this down into jobs for LS101x, LS104x and LS108x instead. While in
here, in the name portion of these jobs, refer to them as NXP for ARM
and not Freescale as they've been NXP for quite some time.
Vignesh R [Wed, 16 Jan 2019 09:24:36 +0000 (14:54 +0530)]
configs: Remove am43xx_evm_ethboot_defconfig
am43xx_evm_ethboot_defconfig is not being actively used and has not been
moved to DM or DT. Also, ethboot cannot be tested on AM43xx EVM as such
due EVM limitations. Therefore delete it.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Patrick Wildt [Tue, 15 Jan 2019 15:34:19 +0000 (16:34 +0100)]
mkimage: fixup CONFIG_FIT_EXTERNAL_OFFSET
The last parameter is expected to be the imagefile. Since -E is a
flag having the output name before -p will make mkimage ignore the
external offset option.
projects / u-boot.git / log
