Pali Rohár [Sat, 21 Jan 2023 11:59:20 +0000 (12:59 +0100)]
tools: kwboot: Fix patching of SPI/NOR XIP images
Marvell BootROM interprets execaddr of SPI/NOR XIP images as relative byte
offset from the from the beginning of the flash device. So if data image
offset and execute offset are not same then it is needed to adjust them
also in DDR RAM.
Fixes: f2c644e0b8bc ("tools: kwboot: Patch destination address to DDR area for SPI image") Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 8 Jan 2023 12:46:14 +0000 (13:46 +0100)]
tools: kwboot: Add check that kwbimage contains DDR init code
Some NOR images may be execute-in-place and do not contain DDR init code in
its kwbimage header. Such images cannot be booted over UART as BootROM
loads them to RAM. Add check that kwbimage contains DDR init code in its
header (either as binary code header or as the simple register-value set).
In some cases it is possible to load very small image into L2SRAM and when
DDR init code is not required. So check for L2SRAM load address and skip
DDR init code check in this case.
Pali Rohár [Sun, 8 Jan 2023 12:38:27 +0000 (13:38 +0100)]
tools: kwboot: Fix parsing UART image without data checksum
The 32-bit data checksum in UART image is not checked by the BootROM and
also Marvell tools do not generate it.
So if data checksum stored in UART image does not match calculated checksum
from the image then treat those checksum bytes as part of the executable
image code (and not as the checksum) and for compatibility with the rest of
the code manually insert data checksum into the in-memory image after the
executable code, without overwriting it.
This should allow to boot UART images generated by Marvell tools.
Pali Rohár [Sat, 21 Jan 2023 18:57:28 +0000 (19:57 +0100)]
tools: kwboot: Add image type documentation
Add information of all available image types and where they should be
stored. Storage location offsets where documented from the disassembly of
the A385 BootROM image dump.
Pali Rohár [Sun, 8 Jan 2023 12:34:24 +0000 (13:34 +0100)]
tools: kwboot: Add more documentation references
Add reference to Avanta Boot Flow documentation, BobCat2, AlleyCat3 and
PONCat3 BootROM Firmware documentation and links to public Marvell tools:
hdrparser.c and doimage.c
Pali Rohár [Sun, 8 Jan 2023 23:52:09 +0000 (00:52 +0100)]
arm: mvebu: spl: Fix support for loading U-Boot proper from SD card
Marvell BootROM loads MMC image from sector 0 (HW boot or data partition)
and SD image from sector 1.
So for SD card booting it is needed to not use constant CONFIG MMC options
and instead of them it is needed to define functions spl_mmc_boot_mode()
spl_mmc_get_uboot_raw_sector() which determinate offsets at SPL runtime
based on MMC or SD card.
Calculation of SD card sector expects following values:
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET=0
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0
Fixes: 2226ca173486 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header") Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sat, 21 Jan 2023 14:13:08 +0000 (15:13 +0100)]
spl: mmc: Allow to disable SYS_MMCSD_FS_BOOT_PARTITION
On some platforms is SYS_MMCSD_FS_BOOT_PARTITION unsupported. So allow to
completely disable MMC FS Boot support via new option SYS_MMCSD_FS_BOOT.
By default MMC FS Boot support is enabled (like it was before) except for
ARCH_MVEBU where MMC FS Boot supported is unsupported due to Marvell
BootROM limitations.
When eMMC boot is selected then BootROM loads kwbimage header (U-Boot SPL)
from the selected eMMC boot partition. So for eMMC boot ensure that U-Boot
SPL loads U-Boot proper (from kwbimage) also from the same selected eMMC
boot partition.
Fixes: 2226ca173486 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header") Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 8 Jan 2023 12:27:07 +0000 (13:27 +0100)]
arm: mvebu: spl: Remove checks for BOOT_DEVICE_MMC2 and BOOT_DEVICE_MMC2_2
BOOT_DEVICE_MMC2 and BOOT_DEVICE_MMC2_2 are representing mmc dev 1 but all
Armada SoCs have only one mmc controller. So remove references to
non-existent second mmc controller.
Pali Rohár [Sat, 21 Jan 2023 12:59:20 +0000 (13:59 +0100)]
cmd: mvebu/bubt: Fix parsing SATA kwbimage
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
Reject invalid and accept valid SATA images.
Fixes: 5a0653493307 ("cmd: mvebu/bubt: Check for A38x image data checksum") Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sat, 21 Jan 2023 12:47:45 +0000 (13:47 +0100)]
arm: mvebu: spl: Fix parsing SATA kwbimage
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
To process SATA kwbimage and load U-Boot proper from it in the same way as
Marvell BootROM, it is needed to interpret srcaddr as relative offset to
the main header. This change fixes booting of U-Boot proper from SPL code
in SATA image.
Fixes: 2226ca173486 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header") Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sat, 21 Jan 2023 12:45:36 +0000 (13:45 +0100)]
tools: kwboot: Fix parsing SATA kwbimage
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
To parse SATA kwbimage in the same way as Marvell BootROM, it is needed to
interpret srcaddr as relative offset to the main header. This change fixes
loading of SATA images via kwboot over UART.
Pali Rohár [Sat, 21 Jan 2023 12:34:55 +0000 (13:34 +0100)]
tools: kwbimage: Fix generating, verifying and extracting SATA kwbimage
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
The main header is stored at absolute sector number 1. So do not add or
subtract it when calculating with relative offsets to the main header.
Fixes: 501a54a29cc2 ("tools: kwbimage: Fix generation of SATA, SDIO and PCIe images") Fixes: 5c61710c9880 ("tools: kwbimage: Properly set srcaddr in kwbimage v0") Fixes: e0c243c398a7 ("tools: kwbimage: Validate data checksum of v1 images") Fixes: aa6943ca3122 ("kwbimage: Add support for extracting images via dumpimage tool") Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 8 Jan 2023 12:18:39 +0000 (13:18 +0100)]
cmd: mvebu/bubt: Fix parsing SDIO kwbimage
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To ensure that we do not store invalid SDIO image to the boot location
(read by the Marvell BootROM), we need to check that image is valid
and srcaddr is intepreted in bytes, in the same way as it is done by
Marvell BootROM.
This fixes rejecting valid and accepting invalid SDIO images by bubt command.
Fixes: 5a0653493307 ("cmd: mvebu/bubt: Check for A38x image data checksum") Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 8 Jan 2023 12:16:38 +0000 (13:16 +0100)]
arm: mvebu: spl: Fix parsing SDIO kwbimage
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To process SDIO kwbimage and load U-Boot proper from it in the same way as
Marvell BootROM, it is needed to interpret srcaddr in bytes. This change
fixes booting of U-Boot proper from SPL code stored in SDIO image.
Fixes: 2226ca173486 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header") Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Sun, 8 Jan 2023 12:20:20 +0000 (13:20 +0100)]
tools: kwboot: Fix parsing SDIO kwbimage
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To parse SDIO kwbimage in the same way as Marvell BootROM, it is needed to
interpret srcaddr in bytes. This change fixes loading of SDIO images via
kwboot over UART.
Pali Rohár [Sun, 8 Jan 2023 12:22:03 +0000 (13:22 +0100)]
tools: kwbimage: Fix generating, verifying and extracting SDIO kwbimage
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To generate SDIO kwbimage compatible with Marvell BootROM, it is needed to
have srcaddr in bytes. This change fixes SDIO images for Armada 38x SoCs.
Fixes: 501a54a29cc2 ("tools: kwbimage: Fix generation of SATA, SDIO and PCIe images") Fixes: 5c61710c9880 ("tools: kwbimage: Properly set srcaddr in kwbimage v0") Fixes: e0c243c398a7 ("tools: kwbimage: Validate data checksum of v1 images") Fixes: aa6943ca3122 ("kwbimage: Add support for extracting images via dumpimage tool") Signed-off-by: Pali Rohár <pali@kernel.org>
Tom Rini [Tue, 28 Feb 2023 14:50:16 +0000 (09:50 -0500)]
Merge tag 'tpm-next-28022023' of https://source.denx.de/u-boot/custodians/u-boot-tpm into next
TPM auto startup and testing:
Due to U-Boot's lazy binding we always relied on command line tools to
initialize the TPM subsystem and devices. One exception is the EFI
subsystem. When compiled with TCG2 measured boot support the TPM was
automatically initialized.
However that init was not complete. The TCG specs [0] (and specifically
§12.3 Self-test modes) describe how self-tests on the device should be
performed. This PR is adding an extra API function, that can be used to
initialize the TPM2.0 properly.
Simon added the equivalent for TPM1.2 and refactored the DM tests to
include the new funtion.
- mark reserved blocks from Ashok Reddy Soma
- backport BRCMNAND changes from Linux from Linus Walleij
- fix display of unknown raw ID from Patrice Chotard
- show reserved block in chip.erase from Michael Trimarchi
Simon Glass [Tue, 21 Feb 2023 13:24:51 +0000 (06:24 -0700)]
tpm: Separate out the TPM tests for v1 and v2
Currently there is only one test and it only works on TPM v2. Update it
to work on v1.2 as well, using a new function to pick up the required
TPM.
Update sandbox to include both a v1.2 and v2 TPM so that this works.
Split out the existing test into two pieces, one for init and one for
the v2-only report_state feature.
Ilias Apalodimas [Sat, 18 Feb 2023 15:18:49 +0000 (17:18 +0200)]
tpm: sandbox: Change the return code when device is already open
All the TPM drivers as well as out TCG TIS API for a TPM2.0 device
return -EBUSY if the device has already been opened. Adjust
the sandbox TPM do return the same error code.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Ilias Apalodimas [Wed, 25 Jan 2023 11:06:03 +0000 (13:06 +0200)]
efi_loader: use tpm_auto_start for the tpm device
A previous commit is adding a new tpm startup functions which
initializes the TPMv2 and performs all the needed selftests.
Since the TPM selftests might be needed depending on the requested
algorithm or functional module use that instead.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Ilias Apalodimas [Wed, 25 Jan 2023 10:18:36 +0000 (12:18 +0200)]
tpm: add a function that performs selftest + startup
As described in [0] if a command requires use of an untested algorithm
or functional module, the TPM performs the test and then completes the
command actions.
Since we don't check for TPM_RC_NEEDS_TEST (which is the return code of
the TPM in that case) and even if we would, it would complicate our TPM
code for no apparent reason, add a wrapper function that performs both
the selftest and the startup sequence of the TPM.
It's worth noting that this is implemented on TPMv2.0. The code for
1.2 would look similar, but I don't have a device available to test.
The "nand chip.erase" command always printed as bad blocks even in the
case of reserved blocks. Reserved blocks are used for storing bad block
tables. The patch displays "bbt reserved" when printing reserved blocks in
"nand chip.erase" command.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Patrice Chotard [Mon, 13 Feb 2023 17:30:04 +0000 (18:30 +0100)]
mtd: spinand: Fix display of unknown raw ID
In case ID is not found in manufacturer table, the raw ID is
printed using %*phN format which is not supported by lib/vsprintf.c.
The information displayed doesn't reflect the raw ID return by the
unknown spi-nand.
Use %02x format instead, as done in spi-nor-core.c.
For example, before this patch:
ERROR: spi-nand: spi_nand flash@0: unknown raw ID f74ec040
after
ERROR: spi-nand: spi_nand flash@0: unknown raw ID 00 c2 26 03
Fixes: 0a6d6bae0386 ("mtd: nand: Add core infrastructure to support SPI NANDs") Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Acked-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
mtd: rawnand: brcmnand: fix OOB R/W with Hamming ECC
Hamming ECC doesn't cover the OOB data, so reading or writing OOB shall
always be done without ECC enabled.
This is a problem when adding JFFS2 cleanmarkers to erased blocks. If JFFS2
clenmarkers are added to the OOB with ECC enabled, OOB bytes will be changed
from ff ff ff to 00 00 00, reporting incorrect ECC errors.
Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210224080210.23686-1-noltari@gmail.com
[Ported to U-Boot from the Linux kernel] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: William Zhang <william.zhang@broadcom.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The current code checks that the whole OOB area is erased.
This is a problem when JFFS2 cleanmarkers are added to the OOB, since it will
fail due to the usable OOB bytes not being 0xff.
Correct this by only checking that data and ECC bytes aren't 0xff.
Fixes: 02b88eea9f9c ("mtd: brcmnand: Add check for erased page bitflips") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200512082451.771212-1-noltari@gmail.com
[Ported to U-Boot from the Linux kernel] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: William Zhang <william.zhang@broadcom.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Kamal Dasu [Sat, 11 Feb 2023 15:29:03 +0000 (16:29 +0100)]
mtd: nand: brcmnand: Add support for flash-dma v0
This change adds support for flash dma v0.0.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[Ported to U-Boot from the Linux kernel] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: William Zhang <william.zhang@broadcom.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
In brcmstb_nand_verify_erased_page(), the ECC chunk pointer calculation
while correcting erased page bitflips is wrong, fix it.
Fixes: 02b88eea9f9c ("mtd: brcmnand: Add check for erased page bitflips") Signed-off-by: Claire Lin <claire.lin@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[Ported to U-Boot from the Linux kernel] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: William Zhang <william.zhang@broadcom.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Kamal Dasu [Sat, 11 Feb 2023 15:29:01 +0000 (16:29 +0100)]
mtd: rawnand: brcmnand: Add support for v7.3 controller
This change adds support for brcm NAND v7.3 controller. This controller
uses a newer version of flash_dma engine and change mostly implements
these differences.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[Ported to U-Boot from the Linux kernel] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: William Zhang <william.zhang@broadcom.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Kamal Dasu [Sat, 11 Feb 2023 15:29:00 +0000 (16:29 +0100)]
mtd: rawnand: brcmnand: Refactored code to introduce helper functions
Refactored NAND ECC and CMD address configuration code to use helper
functions.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[Ported to U-Boot from the Linux kernel] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Acked-by: William Zhang <william.zhang@broadcom.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reserved blocks are used for storing bad block tables. With "nand bad"
command, these reserved blocks are shown as bad blocks. This is leading
to confusion when compared with Linux bad blocks. Hence, display
"bbt reserved" when printing reserved blocks with "nand bad" command.
To acheive this, return 2 which represents reserved from nand_isbad_bbt()
instead of 1 in case of reserved blocks and catch it in cmd/nand.c.
"nand bad" command display's hexadecimal numbers, so add "0x" prefix.
Tom Rini [Sat, 25 Feb 2023 17:44:30 +0000 (12:44 -0500)]
Merge branch '2023-02-24-include-nx51-components-in-docker-for-testing' into next
- Merge in changes to our Dockerfile so that we build and download ahead
of time all of the components required to run the nx51 test scripts.
This will both speed up the specific job and address failures in Azure
where the ipk files fail to download.
Pali Rohár [Tue, 21 Feb 2023 16:22:29 +0000 (11:22 -0500)]
CI: Update test/nokia_rx51_test.sh to use prebuilt images
Now that the Dockerfile creates images which have the binaries we
require included, have CI make symlinks for them and update the existing
script to support this.
Signed-off-by: Tom Rini <trini@konsulko.com> Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 23 Feb 2023 22:30:49 +0000 (17:30 -0500)]
Merge branch '2023-02-23-assorted-fixes'
- btrfs bugfix, silence a bunch of gcc-12.2 linker warnings finally,
relax one of the trace test time requirements (so CI doesn't fail due
to test being slightly slow, but still correct), and correct env on
MMC and checking for where GPT can be
Maxim Schwalm [Tue, 14 Feb 2023 17:35:30 +0000 (19:35 +0200)]
ARM: tegra: provide default USB gadget setup
All Nvidia boards use the same manufacturer, vendor ID and product ID
for the gadgets. Make them the defaults to remove some boilerplate from
the defconfigs.
Inspired by commit e02687bda96c ("sunxi: provide default USB gadget
setup") which did the same for Allwinner boards.
Tested-by: Thierry Reding <treding@nvidia.com> # T30 and T124 Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com> Signed-off-by: Tom <twarren@nvidia.com>
Svyatoslav Ryhel [Tue, 14 Feb 2023 17:35:29 +0000 (19:35 +0200)]
spi: tegra20_slink: accept any word length
Original t20 slink could work with commands only
fully divisible by 8. This patch removes such
restriction, so commands of any bitlength now
can be passed and processed.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF600T T30 Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30 Tested-by: Thierry Reding <treding@nvidia.com> # T30 and T124 Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> Signed-off-by: Tom <twarren@nvidia.com>
Svyatoslav Ryhel [Tue, 14 Feb 2023 17:35:26 +0000 (19:35 +0200)]
ARM: tegra: clock: add clock_decode_pair helper
Get periph clock id and its parent from device tree.
This works by looking up the peripheral's 'clocks' node and
reading out the second and fourth cells, which are the
peripheral and PLL clock numbers.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30 Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20 Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> Signed-off-by: Tom <twarren@nvidia.com>
Svyatoslav Ryhel [Tue, 14 Feb 2023 17:35:25 +0000 (19:35 +0200)]
ARM: tegra: clock: add clk_id_to_pll_id helper
This function allows to convert a device tree clock ID to PLL ID.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30 Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20 Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com> Signed-off-by: Tom <twarren@nvidia.com>
Marek Vasut [Thu, 9 Feb 2023 12:30:10 +0000 (13:30 +0100)]
env: mmc: Apply GPT only on eMMC user HW partition
Apply the GPT U-Boot environment GUID type look up only on eMMC user
HW partition, do not apply the look up on eMMC boot HW partitions as
mmc_offset_try_partition() assumes either SD partitions or eMMC user
HW partition.
This fixes environment operation on systems where CONFIG_SYS_MMC_ENV_PART
is non-zero and CONFIG_SYS_REDUNDAND_ENVIRONMENT is set.
Fixes: 80105d8fd52 ("env: mmc: select GPT env partition by type guid") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Fri, 17 Feb 2023 22:45:16 +0000 (15:45 -0700)]
trace: Relax test requirements
We expect the profile and bootstage to agree on timing, but when
running on slow machines there can be a larger descrepency. Increase the
tolerance to fix this.
Fixes: 9cea4797aeb ("trace: Add a test") Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 14 Feb 2023 20:09:31 +0000 (15:09 -0500)]
Makefile: Link with -z noexectack
When moving to gcc-12.2 we started trying to quiet some of the new
linker warnings, that are not relevant to us. However, a
misunderstanding of the mechanics at play meant that I intentionally
omitted passing -z noexecstack to the linker, when we do need to. Add
this flag and in turn remove warnings from the linker.
Fixes: 1e1c51f8ace8 ("Makefile: link with --no-warn-rwx-segments") Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Note the second and the last line, the @cur_len is 450+MiB, which is
almost a chunk size.
And inside __btrfs_map_block(), we limits the returned value to stripe
length, but that's depending on the chunk type:
if (map->type & (BTRFS_BLOCK_GROUP_RAID0 | BTRFS_BLOCK_GROUP_RAID1 |
BTRFS_BLOCK_GROUP_RAID1C3 | BTRFS_BLOCK_GROUP_RAID1C4 |
BTRFS_BLOCK_GROUP_RAID5 | BTRFS_BLOCK_GROUP_RAID6 |
BTRFS_BLOCK_GROUP_RAID10 |
BTRFS_BLOCK_GROUP_DUP)) {
/* we limit the length of each bio to what fits in a stripe */
*length = min_t(u64, ce->size - offset,
map->stripe_len - stripe_offset);
} else {
*length = ce->size - offset;
}
This means, if the chunk is SINGLE profile, then we don't limit the
returned length at all, and even for other profiles, we can still return
a length much larger than the requested one.
[FIX]
Properly clamp the returned length, preventing it from returning a much
larger range than expected.
Reported-by: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Qu Wenruo <wqu@suse.com>
Kunihiko Hayashi [Mon, 20 Feb 2023 05:50:32 +0000 (14:50 +0900)]
phy: socionext: Add UniPhier USB3 PHY driver
Add USB3 PHY driver support to control clocks and resets needed to enable
PHY. The phy_ops->init() and exit() control PHY clocks and resets only,
and clocks and resets for the controller and the parent logic are enabled
in advance.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
The controller needs to deassert "controller-reset" in USB glue before
the controller registers are accessed. The glue needs to deassert
"syscon-reset" before the glue registers are accessed.
The glue itself doesn't have "syscon-reset", so the controller-reset
controls "syscon-reset" instead.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
Kunihiko Hayashi [Mon, 20 Feb 2023 05:50:28 +0000 (14:50 +0900)]
usb: dwc3-generic: Export glue structures and functions
In order to allow external SoC-dependent glue drivers to use dwc3-generic
functions, push the glue structures and export the functions to a header
file.
The SoC-dependent glue drivers can only define their own wrapper driver
and specify these functions. The drivers can also add their own compatible
strings and configure functions.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Reviewed-by: Marek Vasut <marex@denx.de>
Kunihiko Hayashi [Mon, 20 Feb 2023 05:50:26 +0000 (14:50 +0900)]
usb: dwc3-generic: Allow different controller DT node pattern
The most of devicetree has the following USB node structure.
The controller node is placed as a child node of the glue node.
Current dwc3-generic driver works on this premise.
Marek Vasut [Mon, 20 Feb 2023 05:50:25 +0000 (14:50 +0900)]
usb: dwc3: Look up reference clock DT phandle in both controller DT nodes
There are currently four disparate placement possibilities of DWC3
reference clock phandle in SoC DTs:
- in top level glue node, with generic subnode without clock (ZynqMP)
- in top level generic node, with no subnode (i.MX8MQ)
- in generic subnode, with other clock in top level node (i.MX8MP)
- in both top level node and generic subnode (Rockchip)
Cover all the possibilities here by looking into both nodes, start
with the top level node as that seems to be used in majority of DTs
to reference the clock.
Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Etienne Carriere [Thu, 16 Feb 2023 17:21:41 +0000 (18:21 +0100)]
efi_loader: set CapsuleMax from CONFIG_EFI_CAPSULE_MAX
Adds CONFIG_EFI_CAPSULE_MAX to configure the max index value used in
EFI capsule reports. Prior to this change is the hard coded value was
65535 which would exceed available storage for variables. Now the
default value is 15 which should work fine with most systems.
Etienne Carriere [Thu, 16 Feb 2023 16:29:48 +0000 (17:29 +0100)]
efi_loader: Measure the loaded DTB
Measures the DTB passed to the EFI application upon new boolean config
switch CONFIG_EFI_TCG2_PROTOCOL_MEASURE_DTB. For platforms where the
content of the DTB passed to the OS can change across reboots, there is
not point measuring it hence the config switch to allow platform to not
embed this feature.
This patch adds a brief introduction to the RISC-V architecture and
the typical boot process used on a variety of RISC-V platforms.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
doc: board: bcm7xxx: Convert to reStructuredText format
Convert the documentation for the Broadcom BCM7445 and BCM7260 boards
to reStructuredText format and add the new filename to
doc/board/broadcom/index.rst.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
projects / u-boot.git / log
