Hanyuan Zhao [Fri, 9 Aug 2024 08:56:59 +0000 (16:56 +0800)]
net: dc2114x: allow users to decide whether to detect the tx No Carrier errors
Some IP cores of dc2114x or its variants do not comply so well with
the behaviors described by the official document. A packet could be
sent successfully but reported with No Carrier error. Latest drivers
of this IP core have not detect this error anymore.
Hanyuan Zhao [Fri, 9 Aug 2024 08:56:58 +0000 (16:56 +0800)]
net: dc2114x: remove unused lines and change the var and print types
This commit fixes a problem that even though the network card does not report
any issues in transmitting a setup frame, the driver prints the error status
every time. Let's set it for debug use.
Hanyuan Zhao [Fri, 9 Aug 2024 08:56:57 +0000 (16:56 +0800)]
net: dc2114x: add support for CPUs that have cache between the memory and the card
This commit adds support for the MIPS and LoongArch CPUs, which would use cache
after they jump into U-Boot. This commit requests the CPU to return the
addresses in uncached windows and flushes the cache in need, to make sure the
memory between the CPU and the network card is in consistency.
Hanyuan Zhao [Fri, 9 Aug 2024 08:56:54 +0000 (16:56 +0800)]
net: dc2114x: add support for platforms that don't have pci controllers
There're a few ethernet IP cores which have the same functions with dc2114x,
and can be connected to CPU by AXI or other buses. This commit adds support
for the platforms that do not have PCI controllers, using MMIO to communicate
with the dc2114x IP core.
- New boards:
rk3566: Hardkernel ODROID-M1S
rk3588s: Hardkernel ODROID-M2
rk3588: NanoPC-T6 LTS
- Migrate to use USB_DWC3_GENERIC for rk3328
- Other board level config and dts update
Jonas Karlman [Thu, 17 Oct 2024 20:00:27 +0000 (20:00 +0000)]
rockchip: rk3588-nanopc-t6: Add support for NanoPC-T6 LTS
Update defconfig to enable features included in pending upstream DT and
implement board_fit_config_name_match() to load correct DT for LTS and
non-LTS version of the NanoPC-T6.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(cherry picked from commit 7588da65fdf09c7de9f903780c212a8ae96f2866) Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the LTS (2310) version the miniPCIe slot got removed and USB 2.0
setup has changed. There are two external accessible ports and two ports
on the internal header.
There is an on-board USB hub which provides:
- one external connector (bottom one)
- two internal ports on pin header
- one port for m.2 E connector
The top USB 2.0 connector comes directly from the SoC.
(cherry picked from commit f4a834fbc8cdb40fddd63d083e8d1c6189ba62dc) Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(cherry picked from commit 697963b1c22336a44ac2e33536c652aae1671b3d) Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Alex Shumsky [Wed, 16 Oct 2024 10:02:03 +0000 (13:02 +0300)]
rockchip: board: Increase rng-seed size to make it sufficient for modern Linux
Increase rng-seed size to make Linux happy and initialize rng pool instantly.
Linux 5.19+ requires 32 bytes of entropy to initialize random pool, but u-boot
currently provides only 8 bytes.
Linux 5.18 and probably some versions before it used to require 64 bytes.
Bump min value to 64 bytes to be on a safe side.
Linux source references:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/char/random.c?h=v5.19#n551
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/char/random.c?h=v5.18#n236
Signed-off-by: Alex Shumsky <alexthreed@gmail.com> Fixes: d2048bafae40 ("rockchip: board: Add board_rng_seed() for all Rockchip devices") Reviewed-by: Dragan Simic <dsimic@manjaro.org> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Remove unneeded USB board code and fix reset on mx6ul_14x14_evk.
- Update fastboot buffer size/address for verdin-imx8m{m|p}.
- Fix imxrt1050-evk boot and convert it to standard boot.
- Fix imx8qxp-mek and imx8qm-mek boot.
- Add support for the i.MX93 9X9 QSB board.
- Make livetree API to work on i.MX.
- Set sane default value for i.MX8M SPL_LOAD_FIT_ADDRESS.
- Deduplicate DH i.MX8MP/i.MX6 DHSOM defconfigs.
- Select default TEXT_BASE for i.MX6/i.MX7.
- Several updates for DH i.MX8MP DRC02.
Marek Vasut [Sun, 20 Oct 2024 21:00:38 +0000 (23:00 +0200)]
ARM: imx: soc: Select default TEXT_BASE for i.MX6
Select default U-Boot and SPL text base for the i.MX6 SoC. The U-Boot
and SPL text base is picked as the one used by various i.MX6 boards.
Update all the boards.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Jesse Taube [Fri, 25 Oct 2024 02:02:26 +0000 (22:02 -0400)]
imx: imxrt1050-evk: Fix missing clocks for mmc
Two of the clocks required by the usdhc1 controller are missing from the
clock controller node. A recent change enables all the clocks in the
esdhc node, which fails as they are not defined in the clock controller.
Fixes: 76332fae769 ("mmc: fsl_esdhc_imx: Enable AHB/IPG clk with clk bulk API") Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com> Cc: Peng Fan <peng.fan@nxp.com>
Marek Vasut [Fri, 25 Oct 2024 22:55:06 +0000 (00:55 +0200)]
arm64: imx: Deduplicate DH i.MX6 DHSOM defconfig
Deduplicate defconfigs for all DH i.MX6 DHSOM by including common
configs/imx_dhsom_defconfig . This does introduce changes to the
board configuration, namely it enables commands used on all DHSOM
devices consistenty, the prompt is changed to u-boot=>, support for
booting non-Linux OS which was likely never used is disabled, GPT
partition table support is enabled, generic MTD support is enabled,
LED support is enabled, DM PHY, PMIC and regulator support is also
enabled, KASLR command is enabled.
Deduplicate defconfigs for all DH i.MX8MP DHSOM by factoring out the
common parts into generic _dhsom_defconfig and including those using
the #include <configs/...> preprocessor macro, which is applicable to
defconfigs as well. This enables CMD_EXPORTENV on all iMX8MP DHSOM
systems to be consistent with other DHSOM systems.
Marek Vasut [Fri, 25 Oct 2024 22:55:04 +0000 (00:55 +0200)]
arm64: imx: imx8mp: Disable PCA954x I2C mux on DH i.MX8MP DRC02 and PicoITX
Neither the DRC02 nor PicoITX carrier board contains the PCA954x I2C mux
chip, the chip is only present on PDK3 carrier board. Disable support for
the PCA954x mux chip and I2C mux altogether on both i.MX8MP DHCOM DRC02 and
PicoITX.
Tom Rini [Fri, 25 Oct 2024 20:22:36 +0000 (14:22 -0600)]
Merge patch series "Allow showing the memory map"
Simon Glass <sjg@chromium.org> says:
This little series adds a new 'memmap' command, intended to show the
layout of memory within U-Boot and how much memory is available for
loading images.
Simon Glass [Mon, 21 Oct 2024 08:19:29 +0000 (10:19 +0200)]
cmd: Move meminfo command into its own file
In preparation for expanding this command, move it into a separate file.
Rename the function to remove the extra underscore. Update the number of
arguments to 1, since 3 is incorrect.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Mon, 21 Oct 2024 08:19:28 +0000 (10:19 +0200)]
bootstage: Allow counting memory without strings
The bootstage array includes pointers to strings but not the strings
themselves. The strings are added when stashing, but including them in
the size calculation gives an inflated view of the amount of space used
by the array.
Update this function so it can return the amount of memory used by the
bootstage structures themselves, without the strings which they point
to.
Simon Glass [Mon, 21 Oct 2024 08:19:26 +0000 (10:19 +0200)]
common: Tidy up how malloc() is inited
The call to malloc() is a bit strange. The naming of the arguments
suggests that an address is passed, but in fact it is a pointer, at
least in the board_init_r() function and SPL equivalent.
Update it to work as described. Add a function comment as well.
Note that this does adjustment does not extend into the malloc()
implementation itself, apart from changing mem_malloc_init(), since
there are lots of casts and pointers and integers are used
interchangeably.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tom Rini [Fri, 25 Oct 2024 17:55:23 +0000 (11:55 -0600)]
Merge tag 'xilinx-for-v2025.01-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
AMD/Xilinx changes for v2025.01-rc1 v2
.mailmap:
- Switch Padmarao's email to AMD one
zynq_spi:
- Make update_stripe static
xilinx:
- Update DT description for EMMCs
zynqmp:
- Update logic around RPUs and tcm handling
- Update bootmenu selection for Kria
- Add description for SC vm-p-b1369
- Fix comment about file location in zynqmp-p-a2197-00-revA.dts
versal:
- Fix logic around USB boot
versal2:
- Disable useless features for Mini configurations
versal-net:
- Get rid of current-speed DT property from mini configuration
Dfu:
- Rely on device tree for spi speed/mode on spi flash
Android Image:
- Fix booting on platforms having > 4GiB of memory
- Decompress boot image to kernel_addr_r when compression is enabled
- Honor CONFIG_SYS_LOAD_ADDR when mkbootimg uses default address
Bcb:
- Rework bcb command to use U_BOOT_LONGHELP
- Move ab_select cmd to bcb cmd
- Implement ab_dump command in bcb
- bcb: Write '_<slot>' instead of '<slot>' to misc partition
Jonas Karlman [Tue, 8 Oct 2024 20:06:35 +0000 (20:06 +0000)]
board: rockchip: Add Hardkernel ODROID-M1S
The Hardkernel ODROID-M1S is a single-board computer based on Rockchip
RK3566 SoC. It features e.g. 4/8 GB LPDDR4 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0.
Features tested on a ODROID-M1S 8GB rev1.0 20230906:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Tue, 8 Oct 2024 20:06:34 +0000 (20:06 +0000)]
arm64: dts: rockchip: Add Hardkernel ODROID-M1S
The Hardkernel ODROID-M1S is a single-board computer based on Rockchip
RK3566 SoC. It features e.g. 4/8 GB LPDDR4 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0.
Add initial support for eMMC, SD-card, Ethernet, HDMI, PCIe and USB.
Jonas Karlman [Tue, 8 Oct 2024 20:06:33 +0000 (20:06 +0000)]
arm64: dts: rockchip: Correct vendor prefix for Hardkernel ODROID-M1
The vendor prefix for Hardkernel ODROID-M1 is incorrectly listed as
rockchip. Use the proper hardkernel vendor prefix for this board, while
at it also drop the redundant soc prefix.
Jonas Karlman [Tue, 8 Oct 2024 19:27:16 +0000 (19:27 +0000)]
rockchip: Migrate to use USB_DWC3_GENERIC on RK3328
After the full convertion of usb gadget interrupt handling to
usb_gadget_generic_ops, it is now possible to use DM_USB_GADGET,
DWC2_OTG and DWC3_GENERIC together without causing a build error.
Change to use USB_DWC3_GENERIC instead of USB_XHCI_DWC3 to complte the
migration initiated in commit 1bc4e8eb1d7f ("rockchip: Migrate to use
DM_USB_GADGET on RK3328"). No functional change is intended.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Thu, 3 Oct 2024 19:59:34 +0000 (19:59 +0000)]
board: rockchip: Add Hardkernel ODROID-M2
The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.
Features tested on a ODROID-M2 16GB rev1.0 20240611:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Thu, 3 Oct 2024 19:59:33 +0000 (19:59 +0000)]
arm64: dts: rockchip: Add Hardkernel ODROID-M2
The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.
Add initial support for eMMC, SD-card, Ethernet, PCIe and USB.
(cherry picked from commit 7ba62d8b4cb010c6fcb7077550b46d5f5fb5af6d) Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 19 Sep 2024 14:00:21 +0000 (09:00 -0500)]
board: rockchip: Remove ARM SCMI Support from RGxx3
Remove config options for ARM SCMI. It is not required to boot the
board and when using the most recent mainline A-TF it actually causes
the device to freeze during boot due to missing SCMI support.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Thu, 19 Sep 2024 14:00:20 +0000 (09:00 -0500)]
board: rockchip: Add vdd_cpu reg fixup for RGXX3 Series
Some of the Powkiddy devices switched to using a different vendor for
the vdd_cpu regulator. Unfortunately the device does not have a new
revision to denote this, so users have no way of knowing in advance.
Add code to detect if a device is present at addresses 0x1c or 0x40 on
the i2c0 bus and update the devicetree if needed.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dedicated getter and setter for SCLK_UART0_PMU.
This allows the driver to correctly handle UART0 clocks, and thus
it fixes the issues with UART0 not working in case DEBUG_UART is
disabled.
Unlike other Rockchip SoCs, i.e. rk3399, in the PX30 the default
clock source for UART is GPLL, instead of external oscillator.
If the DEBUG_UART is enabled, the clock source is changed in
board_debug_uart_init function to 24Mhz oscillator, which also
matches the fallback value obtained from DT node.
In case the DEBUG_UART is disabled, the UART clock source remains
default, and the DM serial driver wrongly configures the baud rate,
resulting in broken communication.
By implementing the UART clock getter/setter, the serial driver
can probe the actual configuration and corectly configure itself.
The DEBUG_UART settings now should not affect it.
The driver supports GPLL and 24M oscillator. NPLL and USBPHY480M
sources, that are managed by CRU, are not yet handled, as likely
they won't be used in real scenarios.
Padmarao Begari [Fri, 11 Oct 2024 11:34:35 +0000 (17:04 +0530)]
arm64: zynqmp: fix tcm initialization for mini u-boot
Fix the issue introduced by commit fed064477c2c
("arm64: zynqmp: Print an error for split to lock mode switch").
The mini u-boot is hanging, because of the tcm is not initialized.
The mini u-boot is using the tcm to reserve the mmu table and
currently it is not initialized, so allowing u-boot to initialize
the tcm.
Paul Alvin [Wed, 25 Sep 2024 07:03:13 +0000 (09:03 +0200)]
xilinx: Add cap-mmc-hw-reset and no-sd, no-sdio property to eMMC
Add "cap-mmc-hw-reset" property to the eMMC DT node to perform the
eMMC device hardware reset.
Also, add "no-sd", "no-sdio" properties to eMMC DT node to skip
unwanted sd, sdio related commands during initialization for eMMC
device as this may lead to unnecessary register dump.
xilinx: zynqmp: Remove conditional check for bootmenu_default variable
As per bootmenu support added default boot options to CC on AMD CCs and
default to SOM on others.
However, if no secondary boot device is enabled in the design,it should
be the default boot option for SOM when combined with AMD CCs because it
only contains SOM peripherals.
To address this issue, The conditional check for the bootmenu_default
variable was removed, and it has always been set to SOM as the default
boot option.
In this way, users can choose preferred boot options from the bootmenu
based on the boot devices configured in the design for AMD CCs.
Padmarao Begari [Tue, 1 Oct 2024 08:25:37 +0000 (13:55 +0530)]
xilinx: common: fix script address for Microblaze
Fix the issue introduced by commit 067e0294806e
("board: xilinx: Remove conditional check for Microblaze").
The scriptaddr should be physical location not really offset
from start of DDR. When U-Boot is not found boot.scr script
address in device tree, then it is assigned based on script
address and ram base address for Microblaze and i.e exceeding
DDR memory. To fix this, the script address is assigned
initially with offset instead of address. Later it is added
with ram base address and gets the physical address.
arm64: zynqmp: Fix tcminit mode value based on argv
The RPU pytest introduced by commit e894c10c040b
("test/py: zynqmp_rpu: Add test for loading RPU apps") expects
3rd parameter as string not a number that's why extend command
to actually handle both. The issue with existing code is that
when any non number string is passed hextoul returns 0. For
backward compatibility zynqmp tcminit 0/1 can be still used but
it is recommended to use strings instead.
arm64: zynqmp: Print an error for split to lock mode switch
The zynqmp tcminit crashes the U-Boot when switching from
r5-mode "split" to "lockstep" instead it should throw an error.
When cpu is enabled, the check_tcm_mode() function checks
if the previous mode is "split", switch mode is "lockstep" then
it returns the error code and the initialize_tcm() function is not
updating the global control register of the RPU instead it prints
the error message. When cpu is disabled, the check_tcm_mode()
function returns the success code for switch split to lockstep mode.
Rasmus Villemoes [Thu, 24 Oct 2024 10:01:45 +0000 (12:01 +0200)]
imx8m: set sane default value for SPL_LOAD_FIT_ADDRESS
I enabled IMX_HAB on an imx8mp board, but even though I knew about the
implementation, I forgot that I had to provide a sane value for
SPL_LOAD_FIT_ADDRESS. The help text for IMX_HAB doesn't mention this
implicit requirement, and there's no build-time warning; the default
0x0 value just ends up being returned from
board_spl_fit_buffer_addr(), obviously resulting in a non-booting
board.
The existing imx8m* board configs that set a non-zero value currently
all use 0x44000000. The actual value doesn't matter too much, but 0 is
always wrong for imx8m platforms. So just use 0x44000000 as default
for those platforms.
Tim Harvey [Wed, 23 Oct 2024 20:28:53 +0000 (13:28 -0700)]
imx: power-domain: Convert to use livetree API for fdt access
Convert to using livetree API functions.
Without this if livetree is enabled (OF_LIVE) the imx8m-power-domain
driver will (silently) fail to probe its children leaving you with
no power domain support causing issues with certain devices.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Remove FASTBOOT_BUF_SIZE from verdin-imx8mm_defconfig and
verdin-imx8mp_defconfig to use the default value of 0x7000000, aligning
with other Toradex boards.
Update FASTBOOT_BUF_ADDR to 0x44200000, consistent with the value in
previous downstream NXP U-Boot releases. This will make fastboot
applications continue working with upstream U-Boot by using the same
address.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Peng Fan [Sat, 19 Oct 2024 00:51:25 +0000 (08:51 +0800)]
arm: dts: imx8qm-mek: fix boot
serial_init runs into panic because no serial device found.
Update the device tree to include bootph-some-ram for some critial
devices needed in pre-reloc stage
Also update usdhc related properties to avoid card initialization
failure.
Fixes: 8c103c33fb1 ("dm: dts: Convert driver model tags to use new schema") Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Sat, 19 Oct 2024 00:51:24 +0000 (08:51 +0800)]
arm: dts: imx8qxp-mek: fix boot
serial_init runs into panic because no serial device found.
Update the device tree to include bootph-some-ram for some critial
devices needed in pre-reloc tage
Fixes: 8c103c33fb1 ("dm: dts: Convert driver model tags to use new schema") Signed-off-by: Peng Fan <peng.fan@nxp.com>
Andy Shevchenko [Mon, 21 Oct 2024 14:20:45 +0000 (17:20 +0300)]
Mark a few functions static inline
The function prototypes that are defined in the header most likely has
to be marked as static inline. This helps avoiding the compiler warnings:
include/mux.h:120:14: warning: no previous prototype for ‘mux_control_states’ [-Wmissing-prototypes]
include/mux.h:125:18: warning: no previous prototype for ‘mux_control_select’ [-Wmissing-prototypes]
include/mux.h:133:5: warning: no previous prototype for ‘mux_control_deselect’ [-Wmissing-prototypes]
include/mux.h:138:21: warning: no previous prototype for ‘mux_control_get’ [-Wmissing-prototypes]
include/mux.h:143:6: warning: no previous prototype for ‘mux_control_put’ [-Wmissing-prototypes]
include/mux.h:147:21: warning: no previous prototype for ‘devm_mux_control_get’ [-Wmissing-prototypes]
include/mux.h:153:5: warning: no previous prototype for ‘dm_mux_init’ [-Wmissing-prototype ]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Andy Shevchenko [Mon, 21 Oct 2024 13:56:33 +0000 (16:56 +0300)]
cmd: nvedit: Mark a few functions static
Some functions are not used anywhere except the same file
where they are defined. Mark them static. This helps avoiding
the compiler warnings:
cmd/nvedit.c:201:5: warning: no previous prototype for ‘do_env_ask’ [-Wmissing-prototypes]
cmd/nvedit.c:315:5: warning: no previous prototype for ‘do_env_callback’ [-Wmissing-prototypes]
cmd/nvedit.c:384:5: warning: no previous prototype for ‘do_env_flags’ [-Wmissing-prototype ]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
There are no users of the blk_create_device() function outside the uclass.
Let's make it static. This will ensure that new block drivers will use
blk_create_devicef().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Add the latest 4000 MT/s DDR config generated by
Jacinto7_DDRSS_RegConfigTool Rev 0.11 for J722S , make it the
default config and update A53 default clock to 1.4 GHz matching
the default speed grade (K).
Marek Vasut [Sun, 20 Oct 2024 15:43:12 +0000 (17:43 +0200)]
boot: Introduce BOOTSTD_MENU to control bootflow menu build
The bootflow_menu.c code depends on e.g. scene_txt_set_font(),
which is only built when CONFIG_EXPO is enabled. Introduce new
Kconfig symbol BOOTSTD_MENU which depends on EXPO to prevent
triggering errors like these in case e.g. CONFIG_VIDEO=n :
"
boot/bootflow_menu.c:158:(.text+0x8851): undefined reference to `scene_txt_set_font'
"
Make the symbol depend on BOOTSTD_FULL as well to get rid of
the Makefile dependency workaround. Since BOOTSTD_FULL is not
available in SPL, do not define SPL variant of BOOTSTD_MENU.
Fix up bootflow test accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Han Xu [Sat, 5 Oct 2024 23:46:20 +0000 (07:46 +0800)]
mtd: spi-nor: Add mt35xu01gbba octal mode SPI NOR flash
Add SPI NOR flash id for mt35xu01gbba which supports 4 bytes address with
octal mode read.
Signed-off-by: Han Xu <han.xu@nxp.com> Signed-off-by: Alice Guo <alice.guo@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Neil Armstrong [Thu, 17 Oct 2024 14:44:44 +0000 (16:44 +0200)]
image: android: handle ramdisk default address
The two tools that create android boot images, mkbootimg and the fastboot
client, set the kernel address by default to 0x11008000.
U-boot always honors this field, and will try to copy the ramdisk to
whatever value is set in the header, which won't be mapped to the actual
RAM on most platforms, resulting in the kernel obviously not booting.
All the targets in U-Boot right now will download the android boot image
to CONFIG_SYS_LOAD_ADDR, which means that it will already have been
downloaded to some location that is suitable to use the ramdisk in-place
for header version 0 to 2. For header version 3 and later, the ramdisk
can't be used in-place to use ramdisk_addr_r in this case.
Neil Armstrong [Thu, 17 Oct 2024 14:44:43 +0000 (16:44 +0200)]
image: android: do not boot XIP when kernel is compressed
When trying to boot an android boot image with a compressed
kernel, if the kernel is used in-place because it was created
with mkbootimg, the space will be too small to properly
uncompress.
Take in account the compressed state, and if compressed
use the kernel_addr_r which should be big enough.
Dmitry Rokosov [Thu, 17 Oct 2024 14:12:11 +0000 (17:12 +0300)]
common: android_ab: fix slot suffix for abc block
To align with the official Android BCB (Bootloader Control Block)
specifications, it's important to note that the slot_suffix should start
with an underscore symbol.
For a comprehensive understanding of the expected slot_suffix format in
userspace, please refer to the provided reference [1].
The ab_dump command allows you to display ABC data directly on the
U-Boot console. During an A/B test execution, this test verifies the
accuracy of each field within the ABC data.
Dmitry Rokosov [Thu, 17 Oct 2024 14:12:09 +0000 (17:12 +0300)]
cmd: bcb: change strcmp() usage style in the do_bcb_ab_select()
In the entire cmd/bcb.c file, the return value of strcmp() is not
directly compared to 0. Therefore, it would be better to maintain this
style in the new do_bcb_ab_select() function as well.
Dmitry Rokosov [Thu, 17 Oct 2024 14:12:08 +0000 (17:12 +0300)]
treewide: bcb: move ab_select command to bcb subcommands
To enhance code organization, it is beneficial to consolidate all A/B
BCB management routines into a single super-command.
The 'bcb' command is an excellent candidate for this purpose.
This patch integrates the separate 'ab_select' command into the 'bcb'
group as the 'ab_select' subcommand, maintaining the same parameter list
for consistency.
projects / u-boot.git / log
