From: Fabio Estevam Date: Tue, 15 Mar 2022 20:47:05 +0000 (-0300) Subject: tbs2910: Convert to DM_SERIAL X-Git-Url: http://git.dujemihanovic.xyz/html/static/git-favicon.png?a=commitdiff_plain;h=8fbca1a8b9b02fbc40147401d9af764e07dc96af;p=u-boot.git tbs2910: Convert to DM_SERIAL Conversion to DM_SERIAL is mandatory. Select DM_SERIAL and add a imx6q-tbs2910-u-boot.dtsi file that describes the nodes that require dm-pre-reloc, which allows the DM model to configure the UART pinctrl early. Remove the now unneeded board UART initialization. Signed-off-by: Fabio Estevam Tested-by: Soeren Moch --- diff --git a/arch/arm/dts/imx6q-tbs2910-u-boot.dtsi b/arch/arm/dts/imx6q-tbs2910-u-boot.dtsi new file mode 100644 index 0000000000..65ab052ac2 --- /dev/null +++ b/arch/arm/dts/imx6q-tbs2910-u-boot.dtsi @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0+ + +&aips1 { + u-boot,dm-pre-reloc; +}; + +&pinctrl_uart1 { + u-boot,dm-pre-reloc; +}; + +&soc { + u-boot,dm-pre-reloc; +}; + +&uart1 { + u-boot,dm-pre-reloc; +}; diff --git a/arch/arm/dts/imx6qdl.dtsi b/arch/arm/dts/imx6qdl.dtsi index efd89510d5..d89272039b 100644 --- a/arch/arm/dts/imx6qdl.dtsi +++ b/arch/arm/dts/imx6qdl.dtsi @@ -139,7 +139,7 @@ interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>; }; - soc { + soc: soc { #address-cells = <1>; #size-cells = <1>; compatible = "simple-bus"; @@ -283,7 +283,7 @@ status = "disabled"; }; - bus@2000000 { /* AIPS1 */ + aips1: bus@2000000 { /* AIPS1 */ compatible = "fsl,aips-bus", "simple-bus"; #address-cells = <1>; #size-cells = <1>; diff --git a/board/tbs/tbs2910/tbs2910.c b/board/tbs/tbs2910/tbs2910.c index faf73cc218..3a447ca8a9 100644 --- a/board/tbs/tbs2910/tbs2910.c +++ b/board/tbs/tbs2910/tbs2910.c @@ -22,32 +22,12 @@ #include DECLARE_GLOBAL_DATA_PTR; -#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ - PAD_CTL_SRE_FAST | PAD_CTL_HYS) - -static iomux_v3_cfg_t const uart1_pads[] = { - MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - -static iomux_v3_cfg_t const uart2_pads[] = { - MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - int dram_init(void) { gd->ram_size = 2048ul * 1024 * 1024; return 0; } -static void setup_iomux_uart(void) -{ - imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); - imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); -} - #ifdef CONFIG_FSL_ESDHC_IMX /* set environment device to boot device when booting from SD */ int board_mmc_get_env_dev(int devno) @@ -150,12 +130,6 @@ static void setup_display(void) } #endif /* CONFIG_VIDEO_IPUV3 */ -int board_early_init_f(void) -{ - setup_iomux_uart(); - return 0; -} - #ifdef CONFIG_CMD_BMODE static const struct boot_mode board_boot_modes[] = { /* 4 bit bus width */ diff --git a/configs/tbs2910_defconfig b/configs/tbs2910_defconfig index 993997ba7a..60a816059a 100644 --- a/configs/tbs2910_defconfig +++ b/configs/tbs2910_defconfig @@ -25,7 +25,6 @@ CONFIG_USE_PREBOOT=y CONFIG_PREBOOT="echo PCI:; pci enum; pci 1; usb start; if hdmidet; then run set_con_hdmi; else run set_con_serial; fi" CONFIG_DEFAULT_FDT_FILE="imx6q-tbs2910.dtb" CONFIG_PRE_CONSOLE_BUFFER=y -CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="Matrix U-Boot> " # CONFIG_CMD_BDI is not set @@ -83,6 +82,7 @@ CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y CONFIG_DM_RTC=y CONFIG_RTC_DS1307=y +CONFIG_DM_SERIAL=y CONFIG_MXC_UART=y CONFIG_DM_THERMAL=y CONFIG_IMX_THERMAL=y