From: Tom Rini Date: Sun, 21 Feb 2021 01:05:44 +0000 (-0500) Subject: arm: Remove mx25pdk board X-Git-Url: http://git.dujemihanovic.xyz/html/static/git-favicon.png?a=commitdiff_plain;h=2610bf14b5ca799a90e463666d52535c62beba9b;p=u-boot.git arm: Remove mx25pdk board This board has not been converted to CONFIG_DM_MMC by the deadline. Remove it. Cc: Fabio Estevam Signed-off-by: Tom Rini Reviewed-by: Fabio Estevam --- diff --git a/arch/arm/mach-imx/mx2/Kconfig b/arch/arm/mach-imx/mx2/Kconfig index 30a331ae43..fad5dcc940 100644 --- a/arch/arm/mach-imx/mx2/Kconfig +++ b/arch/arm/mach-imx/mx2/Kconfig @@ -8,12 +8,6 @@ choice prompt "MX25 board select" optional -config TARGET_MX25PDK - bool "Support mx25pdk" - select BOARD_LATE_INIT - select CPU_ARM926EJS - select BOARD_EARLY_INIT_F - config TARGET_ZMX25 bool "Support zmx25" select BOARD_LATE_INIT @@ -24,7 +18,6 @@ endchoice config SYS_SOC default "mx25" -source "board/freescale/mx25pdk/Kconfig" source "board/syteco/zmx25/Kconfig" endif diff --git a/board/freescale/mx25pdk/Kconfig b/board/freescale/mx25pdk/Kconfig deleted file mode 100644 index af06b4c827..0000000000 --- a/board/freescale/mx25pdk/Kconfig +++ /dev/null @@ -1,15 +0,0 @@ -if TARGET_MX25PDK - -config SYS_BOARD - default "mx25pdk" - -config SYS_VENDOR - default "freescale" - -config SYS_SOC - default "mx25" - -config SYS_CONFIG_NAME - default "mx25pdk" - -endif diff --git a/board/freescale/mx25pdk/MAINTAINERS b/board/freescale/mx25pdk/MAINTAINERS deleted file mode 100644 index fa4651e2df..0000000000 --- a/board/freescale/mx25pdk/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -MX25PDK BOARD -M: Fabio Estevam -S: Maintained -F: board/freescale/mx25pdk/ -F: include/configs/mx25pdk.h -F: configs/mx25pdk_defconfig diff --git a/board/freescale/mx25pdk/Makefile b/board/freescale/mx25pdk/Makefile deleted file mode 100644 index d3697d3f5f..0000000000 --- a/board/freescale/mx25pdk/Makefile +++ /dev/null @@ -1,7 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# Copyright (C) 2007, Guennadi Liakhovetski -# -# (C) Copyright 2011 Freescale Semiconductor, Inc. - -obj-y := mx25pdk.o diff --git a/board/freescale/mx25pdk/imximage.cfg b/board/freescale/mx25pdk/imximage.cfg deleted file mode 100644 index 762ccd0ab3..0000000000 --- a/board/freescale/mx25pdk/imximage.cfg +++ /dev/null @@ -1,64 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2009 - * Stefano Babic DENX Software Engineering sbabic@denx.de. - * - * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure - * and create imximage boot image - * - * The syntax is taken as close as possible with the kwbimage - */ - -/* - * Boot Device : one of - * spi, sd (the board has no nand neither onenand) - */ -BOOT_FROM sd - -/* - * Device Configuration Data (DCD) - * - * Each entry must have the format: - * Addr-type Address Value - * - * where: - * Addr-type register length (1,2 or 4 bytes) - * Address absolute address of the register - * value value to be stored in the register - */ -/* EIM config-CS5 init -- CPLD */ -DATA 4 0xB8002050 0x0000D843 -DATA 4 0xB8002054 0x22252521 -DATA 4 0xB8002058 0x22220A00 - -/* DDR2 init */ -DATA 4 0xB8001004 0x0076E83A -DATA 4 0xB8001010 0x00000204 -DATA 4 0xB8001000 0x92210000 -DATA 4 0x80000f00 0x12344321 -DATA 4 0xB8001000 0xB2210000 -DATA 1 0x82000000 0xda -DATA 1 0x83000000 0xda -DATA 1 0x81000400 0xda -DATA 1 0x80000333 0xda - -DATA 4 0xB8001000 0x92210000 -DATA 1 0x80000400 0x12345678 - -DATA 4 0xB8001000 0xA2210000 -DATA 4 0x80000000 0x87654321 -DATA 4 0x80000000 0x87654321 - -DATA 4 0xB8001000 0xB2210000 -DATA 1 0x80000233 0xda -DATA 1 0x81000780 0xda -DATA 1 0x81000400 0xda -DATA 4 0xB8001000 0x82216080 -DATA 4 0x43FAC454 0x00001000 - -DATA 4 0x53F80008 0x20034000 - -/* Enable the clocks */ -DATA 4 0x53f8000c 0x1fffffff -DATA 4 0x53f80010 0xffffffff -DATA 4 0x53f80014 0xfdfff diff --git a/board/freescale/mx25pdk/mx25pdk.c b/board/freescale/mx25pdk/mx25pdk.c deleted file mode 100644 index 3b445a46dd..0000000000 --- a/board/freescale/mx25pdk/mx25pdk.c +++ /dev/null @@ -1,199 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2011 Freescale Semiconductor, Inc. - * - * Author: Fabio Estevam - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#define FEC_RESET_B IMX_GPIO_NR(4, 8) -#define FEC_ENABLE_B IMX_GPIO_NR(2, 3) -#define CARD_DETECT IMX_GPIO_NR(2, 1) - -DECLARE_GLOBAL_DATA_PTR; - -#ifdef CONFIG_FSL_ESDHC_IMX -struct fsl_esdhc_cfg esdhc_cfg[1] = { - {IMX_MMC_SDHC1_BASE}, -}; -#endif - -/* - * FIXME: need to revisit this - * The original code enabled PUE and 100-k pull-down without PKE, so the right - * value here is likely: - * 0 for no pull - * or: - * PAD_CTL_PUS_100K_DOWN for 100-k pull-down - */ -#define FEC_OUT_PAD_CTRL 0 - -#define I2C_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | \ - PAD_CTL_ODE) - -static void mx25pdk_fec_init(void) -{ - static const iomux_v3_cfg_t fec_pads[] = { - MX25_PAD_FEC_TX_CLK__FEC_TX_CLK, - MX25_PAD_FEC_RX_DV__FEC_RX_DV, - MX25_PAD_FEC_RDATA0__FEC_RDATA0, - NEW_PAD_CTRL(MX25_PAD_FEC_TDATA0__FEC_TDATA0, FEC_OUT_PAD_CTRL), - NEW_PAD_CTRL(MX25_PAD_FEC_TX_EN__FEC_TX_EN, FEC_OUT_PAD_CTRL), - NEW_PAD_CTRL(MX25_PAD_FEC_MDC__FEC_MDC, FEC_OUT_PAD_CTRL), - MX25_PAD_FEC_MDIO__FEC_MDIO, - MX25_PAD_FEC_RDATA1__FEC_RDATA1, - NEW_PAD_CTRL(MX25_PAD_FEC_TDATA1__FEC_TDATA1, FEC_OUT_PAD_CTRL), - - NEW_PAD_CTRL(MX25_PAD_D12__GPIO_4_8, 0), /* FEC_RESET_B */ - NEW_PAD_CTRL(MX25_PAD_A17__GPIO_2_3, 0), /* FEC_ENABLE_B */ - }; - - static const iomux_v3_cfg_t i2c_pads[] = { - NEW_PAD_CTRL(MX25_PAD_I2C1_CLK__I2C1_CLK, I2C_PAD_CTRL), - NEW_PAD_CTRL(MX25_PAD_I2C1_DAT__I2C1_DAT, I2C_PAD_CTRL), - }; - - imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads)); - - /* Assert RESET and ENABLE low */ - gpio_direction_output(FEC_RESET_B, 0); - gpio_direction_output(FEC_ENABLE_B, 0); - - udelay(10); - - /* Deassert RESET and ENABLE */ - gpio_set_value(FEC_RESET_B, 1); - gpio_set_value(FEC_ENABLE_B, 1); - - /* Setup I2C pins so that PMIC can turn on PHY supply */ - imx_iomux_v3_setup_multiple_pads(i2c_pads, ARRAY_SIZE(i2c_pads)); -} - -int dram_init(void) -{ - /* dram_init must store complete ramsize in gd->ram_size */ - gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, - PHYS_SDRAM_1_SIZE); - return 0; -} - -/* - * Set up input pins with hysteresis and 100-k pull-ups - */ -#define UART1_IN_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP) -/* - * FIXME: need to revisit this - * The original code enabled PUE and 100-k pull-down without PKE, so the right - * value here is likely: - * 0 for no pull - * or: - * PAD_CTL_PUS_100K_DOWN for 100-k pull-down - */ -#define UART1_OUT_PAD_CTRL 0 - -static void mx25pdk_uart1_init(void) -{ - static const iomux_v3_cfg_t uart1_pads[] = { - NEW_PAD_CTRL(MX25_PAD_UART1_RXD__UART1_RXD, UART1_IN_PAD_CTRL), - NEW_PAD_CTRL(MX25_PAD_UART1_TXD__UART1_TXD, UART1_OUT_PAD_CTRL), - NEW_PAD_CTRL(MX25_PAD_UART1_RTS__UART1_RTS, UART1_OUT_PAD_CTRL), - NEW_PAD_CTRL(MX25_PAD_UART1_CTS__UART1_CTS, UART1_IN_PAD_CTRL), - }; - - imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); -} - -int board_early_init_f(void) -{ - mx25pdk_uart1_init(); - - return 0; -} - -int board_init(void) -{ - /* address of boot parameters */ - gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; - - return 0; -} - -int board_late_init(void) -{ - struct pmic *p; - int ret; - - mx25pdk_fec_init(); - - ret = pmic_init(I2C_0); - if (ret) - return ret; - - p = pmic_get("FSL_PMIC"); - if (!p) - return -ENODEV; - - /* Turn on Ethernet PHY and LCD supplies */ - pmic_reg_write(p, MC34704_GENERAL2_REG, ONOFFE | ONOFFA); - - return 0; -} - -#ifdef CONFIG_FSL_ESDHC_IMX -int board_mmc_getcd(struct mmc *mmc) -{ - /* Set up the Card Detect pin. */ - imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX25_PAD_A15__GPIO_2_1, 0)); - - gpio_direction_input(CARD_DETECT); - return !gpio_get_value(CARD_DETECT); -} - -int board_mmc_init(struct bd_info *bis) -{ - static const iomux_v3_cfg_t sdhc1_pads[] = { - NEW_PAD_CTRL(MX25_PAD_SD1_CMD__SD1_CMD, NO_PAD_CTRL), - NEW_PAD_CTRL(MX25_PAD_SD1_CLK__SD1_CLK, NO_PAD_CTRL), - NEW_PAD_CTRL(MX25_PAD_SD1_DATA0__SD1_DATA0, NO_PAD_CTRL), - NEW_PAD_CTRL(MX25_PAD_SD1_DATA1__SD1_DATA1, NO_PAD_CTRL), - NEW_PAD_CTRL(MX25_PAD_SD1_DATA2__SD1_DATA2, NO_PAD_CTRL), - NEW_PAD_CTRL(MX25_PAD_SD1_DATA3__SD1_DATA3, NO_PAD_CTRL), - }; - - imx_iomux_v3_setup_multiple_pads(sdhc1_pads, ARRAY_SIZE(sdhc1_pads)); - - /* - * Set the eSDHC1 PER clock to the maximum frequency lower than or equal - * to 50 MHz that can be obtained, which requires to use UPLL as the - * clock source. This actually gives 48 MHz. - */ - imx_set_perclk(MXC_ESDHC1_CLK, true, 50000000); - esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC1_CLK); - return fsl_esdhc_initialize(bis, &esdhc_cfg[0]); -} -#endif - -int checkboard(void) -{ - puts("Board: MX25PDK\n"); - - return 0; -} - -/* Lowlevel init isn't used on mx25pdk, so just provide a dummy one here */ -void lowlevel_init(void) {} diff --git a/configs/mx25pdk_defconfig b/configs/mx25pdk_defconfig deleted file mode 100644 index 58d42444b3..0000000000 --- a/configs/mx25pdk_defconfig +++ /dev/null @@ -1,31 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_MX25=y -CONFIG_SYS_TEXT_BASE=0x81200000 -CONFIG_NR_DRAM_BANKS=1 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x60000 -CONFIG_TARGET_MX25PDK=y -CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx25pdk/imximage.cfg" -CONFIG_DEFAULT_FDT_FILE="imx25-pdk.dtb" -CONFIG_HUSH_PARSER=y -CONFIG_CMD_BOOTZ=y -CONFIG_CMD_FUSE=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y -CONFIG_CMD_FS_GENERIC=y -CONFIG_DOS_PARTITION=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_MMC=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_FSL_ESDHC_IMX=y -CONFIG_MII=y -CONFIG_MXC_UART=y -CONFIG_FS_EXT4=y -CONFIG_FS_FAT=y -CONFIG_OF_LIBFDT=y diff --git a/include/configs/mx25pdk.h b/include/configs/mx25pdk.h deleted file mode 100644 index 27d0c25ac7..0000000000 --- a/include/configs/mx25pdk.h +++ /dev/null @@ -1,178 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2011 Freescale Semiconductor, Inc. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include - -/* High Level Configuration Options */ - -#define CONFIG_SYS_TEXT_BASE 0x81200000 -#define CONFIG_SYS_FSL_CLK - -#define CONFIG_SYS_TIMER_RATE 32768 -#define CONFIG_SYS_TIMER_COUNTER \ - (&((struct gpt_regs *)IMX_GPT1_BASE)->counter) - -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG - -#define CONFIG_MACH_TYPE MACH_TYPE_MX25_3DS - -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024) - -/* Physical Memory Map */ - -#define PHYS_SDRAM_1 0x80000000 -#define PHYS_SDRAM_1_SIZE (64 * 1024 * 1024) - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR IMX_RAM_BASE -#define CONFIG_SYS_INIT_RAM_SIZE IMX_RAM_SIZE - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -/* Memory Test */ - -/* Serial Info */ -#define CONFIG_MXC_UART_BASE UART1_BASE - -/* No NOR flash present */ - -/* U-Boot general configuration */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* Ethernet */ -#define CONFIG_FEC_MXC -#define CONFIG_FEC_MXC_PHYADDR 0x1f - -/* ESDHC driver */ -#define CONFIG_SYS_FSL_ESDHC_ADDR IMX_MMC_SDHC1_BASE -#define CONFIG_SYS_FSL_ESDHC_NUM 1 - -/* PMIC Configs */ -#define CONFIG_POWER -#define CONFIG_POWER_I2C -#define CONFIG_POWER_FSL -#define CONFIG_POWER_FSL_MC34704 -#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x54 - -/* I2C Configs */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ -#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ - -/* RTC */ -#define CONFIG_RTC_IMXDI - -/* Fuse API support */ -#define CONFIG_FSL_IIM - -/* Ethernet Configs */ - - -#define CONFIG_LOADADDR 0x81000000 /* loadaddr env var */ -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "script=boot.scr\0" \ - "image=zImage\0" \ - "console=ttymxc0\0" \ - "splashpos=m,m\0" \ - "fdt_high=0xffffffff\0" \ - "initrd_high=0xffffffff\0" \ - "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ - "fdt_addr=0x82000000\0" \ - "boot_fdt=try\0" \ - "ip_dyn=yes\0" \ - "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \ - "mmcpart=1\0" \ - "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \ - "update_sd_firmware_filename=u-boot.imx\0" \ - "update_sd_firmware=" \ - "if test ${ip_dyn} = yes; then " \ - "setenv get_cmd dhcp; " \ - "else " \ - "setenv get_cmd tftp; " \ - "fi; " \ - "if mmc dev ${mmcdev}; then " \ - "if ${get_cmd} ${update_sd_firmware_filename}; then " \ - "setexpr fw_sz ${filesize} / 0x200; " \ - "setexpr fw_sz ${fw_sz} + 1; " \ - "mmc write ${loadaddr} 0x2 ${fw_sz}; " \ - "fi; " \ - "fi\0" \ - "mmcargs=setenv bootargs console=${console},${baudrate} " \ - "root=${mmcroot}\0" \ - "loadbootscript=" \ - "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ - "bootscript=echo Running bootscript from mmc ...; " \ - "source\0" \ - "loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ - "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ - "mmcboot=echo Booting from mmc ...; " \ - "run mmcargs; " \ - "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ - "if run loadfdt; then " \ - "bootz ${loadaddr} - ${fdt_addr}; " \ - "else " \ - "if test ${boot_fdt} = try; then " \ - "bootz; " \ - "else " \ - "echo WARN: Cannot load the DT; " \ - "fi; " \ - "fi; " \ - "else " \ - "bootz; " \ - "fi;\0" \ - "netargs=setenv bootargs console=${console},${baudrate} " \ - "root=/dev/nfs " \ - "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ - "netboot=echo Booting from net ...; " \ - "run netargs; " \ - "if test ${ip_dyn} = yes; then " \ - "setenv get_cmd dhcp; " \ - "else " \ - "setenv get_cmd tftp; " \ - "fi; " \ - "${get_cmd} ${image}; " \ - "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ - "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootz ${loadaddr} - ${fdt_addr}; " \ - "else " \ - "if test ${boot_fdt} = try; then " \ - "bootz; " \ - "else " \ - "echo WARN: Cannot load the DT; " \ - "fi; " \ - "fi; " \ - "else " \ - "bootz; " \ - "fi;\0" - -#define CONFIG_BOOTCOMMAND \ - "mmc dev ${mmcdev}; if mmc rescan; then " \ - "if run loadbootscript; then " \ - "run bootscript; " \ - "else " \ - "if run loadimage; then " \ - "run mmcboot; " \ - "else run netboot; " \ - "fi; " \ - "fi; " \ - "else run netboot; fi" - -/* Miscellaneous configurable options */ - -#endif /* __CONFIG_H */