imx8mm-kontron-bl-osm-s.dtb \
imx8mm-mx8menlo.dtb \
imx8mm-phg.dtb \
- imx8mm-phyboard-polis-rdk.dtb \
- imx8mm-phygate-tauri-l.dtb \
imx8mn-bsh-smm-s2.dtb \
imx8mn-bsh-smm-s2pro.dtb \
imx8mq-cm.dtb \
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2022 PHYTEC Messtechnik GmbH
- * Author: Teresa Remmet <t.remmet@phytec.de>
- */
-
-/dts-v1/;
-
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/phy/phy-imx8-pcie.h>
-#include "imx8mm-phycore-som.dtsi"
-
-/ {
- model = "PHYTEC phyBOARD-Polis-i.MX8MM RDK";
- compatible = "phytec,imx8mm-phyboard-polis-rdk",
- "phytec,imx8mm-phycore-som", "fsl,imx8mm";
-
- chosen {
- stdout-path = &uart3;
- };
-
- bt_osc_32k: bt-lp-clock {
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "bt_osc_32k";
- #clock-cells = <0>;
- };
-
- can_osc_40m: can-clock {
- compatible = "fixed-clock";
- clock-frequency = <40000000>;
- clock-output-names = "can_osc_40m";
- #clock-cells = <0>;
- };
-
- fan {
- compatible = "gpio-fan";
- gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
- gpio-fan,speed-map = <0 0
- 13000 1>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_fan>;
- #cooling-cells = <2>;
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- led-0 {
- color = <LED_COLOR_ID_RED>;
- function = LED_FUNCTION_DISK;
- gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc2";
- };
-
- led-1 {
- color = <LED_COLOR_ID_BLUE>;
- function = LED_FUNCTION_DISK;
- gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- };
-
- led-2 {
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_CPU;
- gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
- };
-
- usdhc1_pwrseq: pwr-seq {
- compatible = "mmc-pwrseq-simple";
- post-power-on-delay-ms = <100>;
- power-off-delay-us = <60>;
- reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
- };
-
- reg_can_en: regulator-can-en {
- compatible = "regulator-fixed";
- gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can_en>;
- regulator-max-microvolt = <3300000>;
- regulator-min-microvolt = <3300000>;
- regulator-name = "CAN_EN";
- startup-delay-us = <20>;
- };
-
- reg_usb_otg1_vbus: regulator-usb-otg1 {
- compatible = "regulator-fixed";
- gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg1pwrgrp>;
- regulator-name = "usb_otg1_vbus";
- regulator-max-microvolt = <5000000>;
- regulator-min-microvolt = <5000000>;
- };
-
- reg_usdhc2_vmmc: regulator-usdhc2 {
- compatible = "regulator-fixed";
- gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- off-on-delay-us = <20000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
- regulator-max-microvolt = <3300000>;
- regulator-min-microvolt = <3300000>;
- regulator-name = "VSD_3V3";
- };
-
- reg_vcc_3v3: regulator-vcc-3v3 {
- compatible = "regulator-fixed";
- regulator-max-microvolt = <3300000>;
- regulator-min-microvolt = <3300000>;
- regulator-name = "VCC_3V3";
- };
-};
-
-/* SPI - CAN MCP251XFD */
-&ecspi1 {
- cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- can0: can@0 {
- compatible = "microchip,mcp251xfd";
- clocks = <&can_osc_40m>;
- interrupt-parent = <&gpio1>;
- interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can_int>;
- reg = <0>;
- spi-max-frequency = <20000000>;
- xceiver-supply = <®_can_en>;
- };
-};
-
-&gpio1 {
- gpio-line-names = "nINT_ETHPHY", "LED_RED", "WDOG_INT", "X_RTC_INT",
- "", "", "", "RESET_ETHPHY",
- "CAN_nINT", "CAN_EN", "nENABLE_FLATLINK", "",
- "USB_OTG_VBUS_EN", "", "LED_GREEN", "LED_BLUE";
-};
-
-&gpio2 {
- gpio-line-names = "", "", "", "",
- "", "", "BT_REG_ON", "WL_REG_ON",
- "BT_DEV_WAKE", "BT_HOST_WAKE", "", "",
- "X_SD2_CD_B", "", "", "",
- "", "", "", "SD2_RESET_B";
-};
-
-&gpio4 {
- gpio-line-names = "", "", "", "",
- "", "", "", "",
- "FAN", "miniPCIe_nPERST", "", "",
- "COEX1", "COEX2";
-};
-
-&gpio5 {
- gpio-line-names = "", "", "", "",
- "", "", "", "",
- "", "ECSPI1_SS0";
-};
-
-&i2c4 {
- clock-frequency = <400000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c4>;
-};
-
-/* PCIe */
-&pcie0 {
- assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
- <&clk IMX8MM_CLK_PCIE1_CTRL>;
- assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
- <&clk IMX8MM_SYS_PLL2_250M>;
- assigned-clock-rates = <10000000>, <250000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pcie>;
- reset-gpio = <&gpio4 9 GPIO_ACTIVE_LOW>;
- status = "okay";
-};
-
-&pcie_phy {
- clocks = <&clk IMX8MM_CLK_PCIE1_PHY>;
- fsl,clkreq-unsupported;
- fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>;
- fsl,tx-deemph-gen1 = <0x2d>;
- fsl,tx-deemph-gen2 = <0xf>;
- status = "okay";
-};
-
-&rv3028 {
- trickle-resistor-ohms = <3000>;
-};
-
-&snvs_pwrkey {
- status = "okay";
-};
-
-/* UART - RS232/RS485 */
-&uart1 {
- assigned-clocks = <&clk IMX8MM_CLK_UART1>;
- assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- uart-has-rtscts;
- status = "okay";
-};
-
-/* UART - Sterling-LWB Bluetooth */
-&uart2 {
- assigned-clocks = <&clk IMX8MM_CLK_UART2>;
- assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
- fsl,dte-mode;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2_bt>;
- uart-has-rtscts;
- status = "okay";
-
- bluetooth {
- compatible = "brcm,bcm43438-bt";
- clocks = <&bt_osc_32k>;
- clock-names = "lpo";
- device-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
- interrupt-names = "host-wakeup";
- interrupt-parent = <&gpio2>;
- interrupts = <9 IRQ_TYPE_EDGE_BOTH>;
- max-speed = <2000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_bt>;
- shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
- vddio-supply = <®_vcc_3v3>;
- };
-};
-
-/* UART - console */
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- status = "okay";
-};
-
-/* USB */
-&usbotg1 {
- adp-disable;
- dr_mode = "otg";
- over-current-active-low;
- samsung,picophy-pre-emp-curr-control = <3>;
- samsung,picophy-dc-vol-level-adjust = <7>;
- srp-disable;
- vbus-supply = <®_usb_otg1_vbus>;
- status = "okay";
-};
-
-&usbotg2 {
- disable-over-current;
- dr_mode = "host";
- samsung,picophy-pre-emp-curr-control = <3>;
- samsung,picophy-dc-vol-level-adjust = <7>;
- status = "okay";
-};
-
-/* SDIO - Sterling-LWB Wifi */
-&usdhc1 {
- assigned-clocks = <&clk IMX8MM_CLK_USDHC1>;
- assigned-clock-rates = <200000000>;
- bus-width = <4>;
- mmc-pwrseq = <&usdhc1_pwrseq>;
- non-removable;
- no-1-8-v;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_wlan>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- brcmf: wifi@1 {
- compatible = "brcm,bcm4329-fmac";
- reg = <1>;
- };
-};
-
-/* SD-Card */
-&usdhc2 {
- assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
- assigned-clock-rates = <200000000>;
- bus-width = <4>;
- cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
- disable-wp;
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
- pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
- pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
- vmmc-supply = <®_usdhc2_vmmc>;
- vqmmc-supply = <®_nvcc_sd2>;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl_bt: btgrp {
- fsl,pins = <
- MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6 0x00
- MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8 0x00
- MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9 0x00
- >;
- };
-
- pinctrl_can_en: can-engrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x00
- >;
- };
-
- pinctrl_can_int: can-intgrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x00
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x80
- MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x80
- MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x80
- MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00
- >;
- };
-
- pinctrl_fan: fan0grp {
- fsl,pins = <
- MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8 0x16
- >;
- };
-
- pinctrl_i2c4: i2c4grp {
- fsl,pins = <
- MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c2
- MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c2
- >;
- };
-
- pinctrl_leds: leds1grp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x16
- MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x16
- MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x16
- >;
- };
-
- pinctrl_pcie: pciegrp {
- fsl,pins = <
- MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9 0x00
- MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12 0x12
- MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19 0x12
- >;
- };
-
- pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
- fsl,pins = <
- MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x40
- >;
- };
-
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x00
- MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x00
- MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x00
- MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x00
- >;
- };
-
- pinctrl_uart2_bt: uart2btgrp {
- fsl,pins = <
- MX8MM_IOMUXC_SAI3_RXC_UART2_DTE_RTS_B 0x00
- MX8MM_IOMUXC_SAI3_RXD_UART2_DTE_CTS_B 0x00
- MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX 0x00
- MX8MM_IOMUXC_SAI3_TXFS_UART2_DTE_TX 0x00
- >;
- };
-
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x40
- MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x40
- >;
- };
-
- pinctrl_usbotg1pwrgrp: usbotg1pwrgrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x00
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x182
- MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0xc6
- MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc6
- MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc6
- MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc6
- MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc6
- >;
- };
-
- pinctrl_usdhc2_gpio: usdhc2gpiogrp {
- fsl,pins = <
- MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x40
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x192
- MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d2
- MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d2
- MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d2
- MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d2
- MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d2
- >;
- };
-
- pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
- MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
- MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
- MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
- MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
- MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
- >;
- };
-
- pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
- MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
- MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
- MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
- MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
- MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
- >;
- };
-
- pinctrl_wlan: wlangrp {
- fsl,pins = <
- MX8MM_IOMUXC_SD1_DATA5_GPIO2_IO7 0x00
- >;
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2022 PHYTEC Messtechnik GmbH
- * Author: Teresa Remmet <t.remmet@phytec.de>
- */
-
-#include "imx8mm.dtsi"
-#include <dt-bindings/net/ti-dp83867.h>
-
-/ {
- model = "PHYTEC phyCORE-i.MX8MM";
- compatible = "phytec,imx8mm-phycore-som", "fsl,imx8mm";
-
- aliases {
- rtc0 = &rv3028;
- rtc1 = &snvs_rtc;
- };
-
- memory@40000000 {
- device_type = "memory";
- reg = <0x0 0x40000000 0 0x80000000>;
- };
-
- reg_vdd_3v3_s: regulator-vdd-3v3-s {
- compatible = "regulator-fixed";
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <3300000>;
- regulator-min-microvolt = <3300000>;
- regulator-name = "VDD_3V3_S";
- };
-};
-
-&A53_0 {
- cpu-supply = <®_vdd_arm>;
-};
-
-&A53_1 {
- cpu-supply = <®_vdd_arm>;
-};
-
-&A53_2 {
- cpu-supply = <®_vdd_arm>;
-};
-
-&A53_3 {
- cpu-supply = <®_vdd_arm>;
-};
-
-&ddrc {
- operating-points-v2 = <&ddrc_opp_table>;
-
- ddrc_opp_table: opp-table {
- compatible = "operating-points-v2";
-
- opp-25000000 {
- opp-hz = /bits/ 64 <25000000>;
- };
-
- opp-100000000 {
- opp-hz = /bits/ 64 <100000000>;
- };
-
- opp-750000000 {
- opp-hz = /bits/ 64 <750000000>;
- };
- };
-};
-
-/* Ethernet */
-&fec1 {
- fsl,magic-packet;
- phy-mode = "rgmii-id";
- phy-handle = <ðphy0>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_fec1>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy0: ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c22";
- enet-phy-lane-no-swap;
- ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
- ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
- ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
- ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
- reg = <0>;
- reset-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
- reset-assert-us = <1000>;
- reset-deassert-us = <1000>;
- };
- };
-};
-
-/* SPI Flash */
-&flexspi {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_flexspi0>;
- status = "okay";
-
- som_flash: flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <80000000>;
- spi-rx-bus-width = <4>;
- spi-tx-bus-width = <1>;
- };
-};
-
-&gpio1 {
- gpio-line-names = "nINT_ETHPHY", "", "WDOG_INT", "X_RTC_INT",
- "", "", "", "RESET_ETHPHY",
- "", "", "nENABLE_FLATLINK";
-};
-
-/* I2C1 */
-&i2c1 {
- clock-frequency = <400000>;
- pinctrl-names = "default","gpio";
- pinctrl-0 = <&pinctrl_i2c1>;
- pinctrl-1 = <&pinctrl_i2c1_gpio>;
- scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- status = "okay";
-
- pmic@8 {
- compatible = "nxp,pf8121a";
- reg = <0x08>;
-
- regulators {
- reg_nvcc_sd1: ldo1 {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <3300000>;
- regulator-min-microvolt = <3300000>;
- regulator-name = "NVCC_SD1 (LDO1)";
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- reg_nvcc_sd2: ldo2 {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <3300000>;
- regulator-min-microvolt = <1800000>;
- regulator-name = "NVCC_SD2 (LDO2)";
- vselect-en;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- reg_vcc_enet: ldo3 {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <2500000>;
- regulator-min-microvolt = <1500000>;
- regulator-name = "VCC_ENET_2V5 (LDO3)";
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- reg_vdda_1v8: ldo4 {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <1800000>;
- regulator-min-microvolt = <1500000>;
- regulator-name = "VDDA_1V8 (LDO4)";
-
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-min-microvolt = <1500000>;
- regulator-suspend-max-microvolt = <1500000>;
- };
- };
-
- reg_soc_vdda_phy: buck1 {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <900000>;
- regulator-min-microvolt = <400000>;
- regulator-name = "VDD_SOC_VDDA_PHY_0P8 (BUCK1)";
-
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-min-microvolt = <400000>;
- regulator-suspend-max-microvolt = <400000>;
- };
- };
-
- reg_vdd_gpu_dram: buck2 {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <1000000>;
- regulator-min-microvolt = <1000000>;
- regulator-name = "VDD_GPU_DRAM (BUCK2)";
-
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-max-microvolt = <1000000>;
- regulator-suspend-min-microvolt = <1000000>;
- };
- };
-
- reg_vdd_gpu: buck3 {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <1000000>;
- regulator-min-microvolt = <400000>;
- regulator-name = "VDD_VPU (BUCK3)";
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- reg_vdd_mipi: buck4 {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <1050000>;
- regulator-min-microvolt = <900000>;
- regulator-name = "VDD_MIPI_0P9 (BUCK4)";
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- reg_vdd_arm: buck5 {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <1050000>;
- regulator-min-microvolt = <400000>;
- regulator-name = "VDD_ARM (BUCK5)";
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- reg_vdd_1v8: buck6 {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <1800000>;
- regulator-min-microvolt = <1800000>;
- regulator-name = "VDD_1V8 (BUCK6)";
-
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-max-microvolt = <1800000>;
- regulator-suspend-min-microvolt = <1800000>;
- };
- };
-
- reg_nvcc_dram: buck7 {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <1100000>;
- regulator-min-microvolt = <1100000>;
- regulator-name = "NVCC_DRAM_1P1V (BUCK7)";
- };
-
- reg_vsnvs: vsnvs {
- regulator-always-on;
- regulator-boot-on;
- regulator-max-microvolt = <1800000>;
- regulator-min-microvolt = <1800000>;
- regulator-name = "NVCC_SNVS_1P8 (VSNVS)";
- };
- };
- };
-
- sn65dsi83: bridge@2d {
- compatible = "ti,sn65dsi83";
- enable-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_sn65dsi83>;
- reg = <0x2d>;
- status = "disabled";
- };
-
- eeprom@51 {
- compatible = "atmel,24c32";
- pagesize = <32>;
- reg = <0x51>;
- vcc-supply = <®_vdd_3v3_s>;
- };
-
- rv3028: rtc@52 {
- compatible = "microcrystal,rv3028";
- interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
- interrupt-parent = <&gpio1>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_rtc>;
- reg = <0x52>;
- };
-};
-
-/* EMMC */
-&usdhc3 {
- assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
- assigned-clock-rates = <400000000>;
- bus-width = <8>;
- keep-power-in-suspend;
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc3>;
- pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
- pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
- non-removable;
- status = "okay";
-};
-
-/* Watchdog */
-&wdog1 {
- fsl,ext-reset-output;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wdog>;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl_fec1: fec1grp {
- fsl,pins = <
- MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x2
- MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x2
- MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90
- MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90
- MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90
- MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90
- MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90
- MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90
- MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x16
- MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x16
- MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x16
- MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x16
- MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x16
- MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x16
- MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x10
- >;
- };
-
- pinctrl_flexspi0: flexspi0grp {
- fsl,pins = <
- MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2
- MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
- MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
- MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
- MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
- MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c0
- MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c0
- >;
- };
-
- pinctrl_i2c1_gpio: i2c1gpiogrp {
- fsl,pins = <
- MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x1e0
- MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x1e0
- >;
- };
-
- pinctrl_rtc: rtcgrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x1c0
- >;
- };
-
- pinctrl_sn65dsi83: sn65dsi83grp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x0
- >;
- };
-
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
- MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
- MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
- MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
- MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
- MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
- MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
- MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
- MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
- MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
- MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
- >;
- };
-
- pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
- fsl,pins = <
- MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
- MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
- MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
- MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
- MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
- MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
- MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
- MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
- MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
- MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
- MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
- >;
- };
-
- pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
- fsl,pins = <
- MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
- MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
- MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
- MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
- MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
- MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
- MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
- MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
- MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
- MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
- MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
- >;
- };
-
- pinctrl_wdog: wdoggrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x26
- >;
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (C) 2023 PHYTEC Messtechnik GmbH
- */
-
-/dts-v1/;
-
-#include <dt-bindings/input/linux-event-codes.h>
-#include <dt-bindings/leds/common.h>
-#include "imx8mm-phycore-som.dtsi"
-
-/ {
- model = "PHYTEC phyGATE-Tauri-L-iMX8MM";
- compatible = "phytec,imx8mm-phygate-tauri-l",
- "phytec,imx8mm-phycore-som", "fsl,imx8mm";
-
- chosen {
- stdout-path = &uart3;
- };
-
- can_osc_40m: clock-can {
- compatible = "fixed-clock";
- clock-frequency = <40000000>;
- clock-output-names = "can_osc_40m";
- #clock-cells = <0>;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpiokeys>;
-
- key {
- gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
- label = "KEY-A";
- linux,code = <KEY_A>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- led-1 {
- color = <LED_COLOR_ID_RED>;
- gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- };
-
- led-2 {
- color = <LED_COLOR_ID_YELLOW>;
- gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- };
- };
-
- usdhc1_pwrseq: pwr-seq {
- compatible = "mmc-pwrseq-simple";
- post-power-on-delay-ms = <100>;
- power-off-delay-us = <60>;
- reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
- };
-
- reg_usb_hub_vbus: regulator-hub-otg1 {
- compatible = "regulator-fixed";
- gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbhubpwr>;
- regulator-name = "usb_hub_vbus";
- regulator-max-microvolt = <5000000>;
- regulator-min-microvolt = <5000000>;
- };
-
- reg_usb_otg1_vbus: regulator-usb-otg1 {
- compatible = "regulator-fixed";
- gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg1pwr>;
- regulator-name = "usb_otg1_vbus";
- regulator-max-microvolt = <5000000>;
- regulator-min-microvolt = <5000000>;
- };
-
- reg_usdhc2_vmmc: regulator-usdhc2 {
- compatible = "regulator-fixed";
- gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- off-on-delay-us = <20000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
- regulator-max-microvolt = <3300000>;
- regulator-min-microvolt = <3300000>;
- regulator-name = "VSD_3V3";
- };
-};
-
-&ecspi1 {
- cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>,
- <&gpio5 13 GPIO_ACTIVE_LOW>,
- <&gpio5 2 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- /* CAN MCP251XFD */
- can0: can@0 {
- compatible = "microchip,mcp251xfd";
- reg = <0>;
- clocks = <&can_osc_40m>;
- interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
- interrupt-parent = <&gpio1>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can_int>;
- spi-max-frequency = <10000000>;
- };
-
- tpm: tpm@1 {
- compatible = "tcg,tpm_tis-spi";
- interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
- interrupt-parent = <&gpio2>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_tpm>;
- reg = <1>;
- spi-max-frequency = <38000000>;
- };
-};
-
-&i2c2 {
- clock-frequency = <400000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c2>;
- pinctrl-1 = <&pinctrl_i2c2_gpio>;
- scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- status = "okay";
-
- temp_sense0: temperature-sensor@49 {
- compatible = "ti,tmp102";
- reg = <0x49>;
- interrupt-parent = <&gpio4>;
- interrupts = <31 IRQ_TYPE_LEVEL_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_tempsense>;
- #thermal-sensor-cells = <1>;
- };
-};
-
-&i2c3 {
- clock-frequency = <400000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c3>;
- pinctrl-1 = <&pinctrl_i2c3_gpio>;
- scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- status = "okay";
-};
-
-&i2c4 {
- clock-frequency = <400000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c4>;
- pinctrl-1 = <&pinctrl_i2c4_gpio>;
- scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
- status = "okay";
-};
-
-/* PCIe */
-&pcie0 {
- assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
- <&clk IMX8MM_CLK_PCIE1_PHY>,
- <&clk IMX8MM_CLK_PCIE1_CTRL>;
- assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
- <&clk IMX8MM_SYS_PLL2_100M>,
- <&clk IMX8MM_SYS_PLL2_250M>;
- assigned-clock-rates = <10000000>, <100000000>, <250000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pcie>;
- reset-gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
- status = "okay";
-};
-
-&pwm1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm1>;
- status = "okay";
-};
-
-&pwm3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm3>;
- status = "okay";
-};
-
-&pwm4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm4>;
- status = "okay";
-};
-
-/* RTC */
-&rv3028 {
- trickle-resistor-ohms = <3000>;
-};
-
-&uart1 {
- assigned-clocks = <&clk IMX8MM_CLK_UART1>;
- assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-/* UART2 - RS232 */
-&uart2 {
- assigned-clocks = <&clk IMX8MM_CLK_UART2>;
- assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
-/* UART - console */
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- status = "okay";
-};
-
-/* USB */
-&usbotg1 {
- adp-disable;
- dr_mode = "otg";
- over-current-active-low;
- samsung,picophy-pre-emp-curr-control = <3>;
- samsung,picophy-dc-vol-level-adjust = <7>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg1>;
- srp-disable;
- vbus-supply = <®_usb_otg1_vbus>;
- status = "okay";
-};
-
-&usbotg2 {
- disable-over-current;
- dr_mode = "host";
- samsung,picophy-pre-emp-curr-control = <3>;
- samsung,picophy-dc-vol-level-adjust = <7>;
- vbus-supply = <®_usb_hub_vbus>;
- status = "okay";
-};
-
-/* SD-Card */
-&usdhc2 {
- assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
- assigned-clock-rates = <200000000>;
- bus-width = <4>;
- cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
- disable-wp;
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
- pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
- pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
- vmmc-supply = <®_usdhc2_vmmc>;
- vqmmc-supply = <®_nvcc_sd2>;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl_can_int: can-intgrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x00
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82
- MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x82
- MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x82
- >;
- };
-
- pinctrl_ecspi1_cs: ecspi1csgrp {
- fsl,pins = <
- MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00
- MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00
- MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x00
- >;
- };
-
- pinctrl_gpiokeys: keygrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x00
- >;
- };
-
- pinctrl_i2c2: i2c2grp {
- fsl,pins = <
- MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c2
- MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c2
- >;
- };
-
- pinctrl_i2c2_gpio: i2c2gpiogrp {
- fsl,pins = <
- MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x1e0
- MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x1e0
- >;
- };
-
-
- pinctrl_i2c3: i2c3grp {
- fsl,pins = <
- MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c2
- MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c2
- >;
- };
-
- pinctrl_i2c3_gpio: i2c3gpiogrp {
- fsl,pins = <
- MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x1e0
- MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x1e0
- >;
- };
-
- pinctrl_i2c4: i2c4grp {
- fsl,pins = <
- MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c2
- MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c2
- >;
- };
-
- pinctrl_i2c4_gpio: i2c4gpiogrp {
- fsl,pins = <
- MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21 0x1e0
- MX8MM_IOMUXC_I2C4_SCL_GPIO5_IO20 0x1e0
- >;
- };
-
- pinctrl_leds: leds1grp {
- fsl,pins = <
- MX8MM_IOMUXC_SAI3_RXD_GPIO4_IO30 0x00
- MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x00
- >;
- };
-
- pinctrl_pcie: pciegrp {
- fsl,pins = <
- /* COEX2 */
- MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x00
- /* COEX1 */
- MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12 0x12
- >;
- };
-
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT 0x40
- >;
- };
-
- pinctrl_pwm3: pwm3grp {
- fsl,pins = <
- MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT 0x40
- >;
- };
-
- pinctrl_pwm4: pwm4grp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO15_PWM4_OUT 0x40
- >;
- };
-
- pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
- fsl,pins = <
- MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x40
- >;
- };
-
- pinctrl_tempsense: tempsensegrp {
- fsl,pins = <
- MX8MM_IOMUXC_SAI3_TXFS_GPIO4_IO31 0x00
- >;
- };
-
- pinctrl_tpm: tpmgrp {
- fsl,pins = <
- MX8MM_IOMUXC_SD1_STROBE_GPIO2_IO11 0x140
- >;
- };
-
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x00
- MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x00
- >;
- };
-
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x00
- MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x00
- >;
- };
-
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140
- MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140
- >;
- };
-
- pinctrl_usbhubpwr: usbhubpwrgrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x00
- >;
- };
-
- pinctrl_usbotg1pwr: usbotg1pwrgrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x00
- >;
- };
-
- pinctrl_usbotg1: usbotg1grp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x80
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x182
- MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0xc6
- MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc6
- MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc6
- MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc6
- MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc6
- >;
- };
-
- pinctrl_usdhc2_gpio: usdhc2gpiogrp {
- fsl,pins = <
- MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x40
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x192
- MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d2
- MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d2
- MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d2
- MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d2
- MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d2
- >;
- };
-
- pinctrl_usdhc2_100mhz: usdhc2100mhzgrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
- MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
- MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
- MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
- MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
- MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
- >;
- };
-
- pinctrl_usdhc2_200mhz: usdhc2200mhzgrp {
- fsl,pins = <
- MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
- MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
- MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
- MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
- MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
- MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
- MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
- >;
- };
-};
select IMX8MM
select SUPPORT_SPL
select IMX8M_LPDDR4
+ imply OF_UPSTREAM
config TARGET_PHYCORE_IMX8MP
bool "PHYTEC PHYCORE i.MX8MP"
M: Teresa Remmet <t.remmet@phytec.de>
W: https://www.phytec.eu/product-eu/system-on-modules/phycore-imx-8m-mini-nano/
S: Maintained
-F: arch/arm/dts/imx8mm-phyboard-polis-rdk.dts
-F: arch/arm/dts/imx8mm-phycore-som.dtsi
F: arch/arm/dts/imx8mm-phyboard-polis-rdk-u-boot.dtsi
-F: arch/arm/dts/imx8mm-phygate-tauri-l.dts
F: arch/arm/dts/imx8mm-phygate-tauri-l-u-boot.dtsi
F: board/phytec/phycore_imx8mm/
F: configs/imx8mm-phygate-tauri-l_defconfig
CONFIG_ENV_SIZE=0x10000
CONFIG_ENV_OFFSET=0x3C0000
CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="imx8mm-phygate-tauri-l"
+CONFIG_DEFAULT_DEVICE_TREE="freescale/imx8mm-phygate-tauri-l"
CONFIG_SPL_TEXT_BASE=0x7E1000
CONFIG_TARGET_PHYCORE_IMX8MM=y
CONFIG_SYS_MONITOR_LEN=524288
CONFIG_ENV_SIZE=0x10000
CONFIG_ENV_OFFSET=0x3C0000
CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="imx8mm-phyboard-polis-rdk"
+CONFIG_DEFAULT_DEVICE_TREE="freescale/imx8mm-phyboard-polis-rdk"
CONFIG_SPL_TEXT_BASE=0x7E1000
CONFIG_TARGET_PHYCORE_IMX8MM=y
CONFIG_SYS_MONITOR_LEN=524288
projects / u-boot.git / commitdiff
