Jacky Bai [Fri, 28 Apr 2023 04:08:44 +0000 (12:08 +0800)]
ddr: imx9: update the rank setting for multi fsp support
The rank setting flow should be updated to support multi
fsp config.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Jacky Bai [Fri, 28 Apr 2023 04:08:43 +0000 (12:08 +0800)]
ddr: imx93: update the ddr init to support mult setpoints
Update the DDR init flow for multi-setpoint support on i.MX93. A new
fsp_cfg struct need to be added in the timing file to store the diff
part of the DDRC and DRAM MR register for each setpoint.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Jacky Bai [Fri, 28 Apr 2023 04:08:42 +0000 (12:08 +0800)]
ddr: imx93: Add 625M bypass clock support
Add 625M bypass clock that may be used DRAM 625M
bypass mode support.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Jacky Bai [Fri, 28 Apr 2023 04:08:41 +0000 (12:08 +0800)]
ddr: imx9: Change the saved ddr data base to 0x2051c000
change the ddr saved info to the last 16KB of the OCRAM.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:40 +0000 (12:08 +0800)]
imx9: imx93_evk: Update spl stack & bss base address
As the ddr timing info will be saved at the last 16KB of
the OCRAM, spl stack & bss base should be updated to avoid
conflict.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Fri, 28 Apr 2023 04:08:39 +0000 (12:08 +0800)]
ddr: imx9: Add workaround for DDRPHY rank-to-rank errata
According to DDRPHY errata, the Rank-to-Rank Spacing and tphy_rdcsgap
specification does not include the Critical Delay Difference (CDD) to
properly define the required rank-to-rank read command spacing after
executing PHY training firmware.
Following the errata workaround, at the end of data training, we get
all CDD values through the MessageBlock, then re-configure the DDRC
timing of WWT/WRT/RRT/RWT with comparing MAX CDD values.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:38 +0000 (12:08 +0800)]
arm: dts: imx93: add tmu
Add tmu nodes and thermal zone
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:37 +0000 (12:08 +0800)]
arm: dts: imx93: sync device tree with Linux
Sync device tree with next-
20230426
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Fri, 28 Apr 2023 04:08:36 +0000 (12:08 +0800)]
imx9: allow to bootaux Mcore with input address
Currently bootaux only supports to boot M33 core from TCM. Since ATF
has changed to use x2 parameter for M33 image address, update the
bootaux command to use input address, so we can support boot from
any possilbe address like TCM, DDR, Flexspi NOR.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:35 +0000 (12:08 +0800)]
imx9: imx93_evk: add low drive mode support on 11x11 EVK
Add a static u-boot config for i.MX93 low drive mode support. When
low drive mode is enabled, VDD_SOC is set to 0.75V. Bus clocks,
A55 core clock (900Mhz), DDR clock (1866MTS), and some peripherals
clocks (USDHC/FLEXSPI/PDM/DISP_PIX/CAM_PIX) must decrease to meet
max frequencies in low drive mode.
Also set standby voltage for buck1
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:34 +0000 (12:08 +0800)]
imx9: use i.MX generic rom api function
There is no need to save gd with using the generic rom api function, so
simplify code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:33 +0000 (12:08 +0800)]
imx9: correct coding style
The end brace should be in a new line
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:32 +0000 (12:08 +0800)]
imx9: add i.MX93 variants support
According to datasheet, iMX93 has fused parts with CORE1 or NPU or
both disabled. So update code to support it, the kernel device tree
runtime update will be added in future patches.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:31 +0000 (12:08 +0800)]
imx9: clock: config arm alt root to 500mhz
Config the A55 alt root clock to 500MHz(LD mode frequency)
by default. Normally, this clock root is only used as an
intermediate clock soure for A55 core/dsu when change the
ARM PLL frequency.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:30 +0000 (12:08 +0800)]
imx9: clock: add CONFIG_IMX9_LOW_DRIVE_MODE support
Add CONFIG_IMX9_LOW_DRIVE_MODE in imx9 clk, later we will
add board support
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:29 +0000 (12:08 +0800)]
imx9: clock: clear HW_CTRL_SEL
The HW_CTRL_SEL should be cleared when configuring PLL to avoid
potential glitch
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:28 +0000 (12:08 +0800)]
imx9: Get market segment and speed grading
Get the chip's market segment and speed grading from fuse and print
them in boot log as other i.MX series.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:27 +0000 (12:08 +0800)]
imx9: soc: support reset cause
Support print reset cause. Since SRSR is not accessible from non-secure
world, so first save it to grp0, then read it in non-secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:26 +0000 (12:08 +0800)]
watchdog: ulp_wdog: guard reset_cpu with condition check
There will be build error if CONFIG_SYSRESET is enabled, so guard
the reset_cpu with condition check here
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Peng Fan [Fri, 28 Apr 2023 04:08:25 +0000 (12:08 +0800)]
imx9: imx93_evk: enable CONFIG_WDT
Without this config, there is boot error: Error binding ulp_wdt driver
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:24 +0000 (12:08 +0800)]
imx9: imx93_evk: select IMX_TMU
Select thermal config to print current temperature
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:23 +0000 (12:08 +0800)]
imx9: imx93_evk: drop unused macro
Drop unused macro
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:22 +0000 (12:08 +0800)]
imx9: imx93_evk: enable CPU_IMX
select CONFIG_CPU_IMX to display cpu info
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Fri, 28 Apr 2023 04:08:21 +0000 (12:08 +0800)]
imx9: Change hard coded MAC to read from fuse
The MAC addresses are hard coded for bring up. Change it to support
reading from fuse.
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:20 +0000 (12:08 +0800)]
imx9: cut off OPTEE memory region from U-Boot
OPTEE memory region is set secure access only in ATF with configuration
to TRDC, and need to remove it from U-Boot, otherwise U-Boot and Kernel
may crash when accessing the memory
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:19 +0000 (12:08 +0800)]
imx9: simplify clk settings
Simplify the clk root settings with an array
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:18 +0000 (12:08 +0800)]
imx9: correct getting LPI2C clk
LPI2C_CLK_ROOT should be used instead of LPUART_CLK_ROOT for i2c
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:17 +0000 (12:08 +0800)]
imx9: use parameter freq when set_arm_clk
The freq parameter was ignored, should use it when configuring ARM PLL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:16 +0000 (12:08 +0800)]
imx9: add more PLL settings
Add more PLL settings for A55 and Display
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:15 +0000 (12:08 +0800)]
imx9: configure M33 systick to 24M
The M33 systick should be 24M per reference mannual, so correct it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:14 +0000 (12:08 +0800)]
imx: imx8_cpu: print cpu grade temperature
Support print out cpu grade temperature
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:13 +0000 (12:08 +0800)]
imx: imx8_cpu: support get temperature for i.MX9
Use CONFIG_DM_THERMAL to make the temperature function could be reused
by i.MX8 and i.MX9
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:12 +0000 (12:08 +0800)]
imx: imx8_cpu: support i.MX9
Add CPU_IMX Kconfig
Support imx8_cpu driver for i.MX9
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:11 +0000 (12:08 +0800)]
imx: imx8_cpu: use static for local functions
For local functions, use static for function.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:10 +0000 (12:08 +0800)]
imx: firmware: sci: add inline functions when IMX8 not enabled
Since we might reuse some drivers for other platforms, while the drivers
have sci firmware api, so to avoid build failure add inline functions
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:09 +0000 (12:08 +0800)]
imx: move imx8 sci header file to include/firmware/imx
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Fri, 28 Apr 2023 04:08:08 +0000 (12:08 +0800)]
imx: spl_imx_romapi: typo fix
Unknow->Unknown
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Fri, 28 Apr 2023 04:08:07 +0000 (12:08 +0800)]
thermal: imx_tmu: Update TMU driver to support iMX93
The TMU used on iMX93 is IP revision 2.1 which is different with previous
revision used on iMX8MQ. So add a new FLAG V4 for this revision to
distinguish the operations.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 28 Apr 2023 04:08:06 +0000 (12:08 +0800)]
imx8ulp: build ahab
The ahab was missed to be compiled, so add it back.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Wed, 12 Apr 2023 12:41:04 +0000 (09:41 -0300)]
ARM: dts: imx7d-sdb-u-boot: Fix usdhc1 UHS operation
Commit
1a7904fdfa7d ("mmc: fsl_esdhc_imx: Use esdhc_soc_data
flags to set host caps") exposed the following SD card error:
U-Boot
2023.04-00652-g487e42f7bc5e (Apr 05 2023 - 22:14:21 -0300)
CPU: Freescale i.MX7D rev1.0 1000 MHz (running at 792 MHz)
CPU: Commercial temperature grade (0C to 95C) at 35C
Reset cause: POR
Model: Freescale i.MX7 SabreSD Board
Board: i.MX7D SABRESD in non-secure mode
DRAM: 1 GiB
Core: 100 devices, 19 uclasses, devicetree: separate
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... Card did not respond to voltage
select! : -110
*** Warning - No block device, using default environment
The reason of the problem, as explained by Ye Li:
"When UHS is enabled in defconfig, the usdhc1 node in imx7d-sdb.dts does
not configure pad for VSELECT, also the data pad should be set to
100Mhz/200Mhz pin states."
Apply these changes into u-boot.dtsi for now. When these changes
reach the Linux mainline imx7d-sdb, they can be dropped from u-boot.dtsi.
This fixes UHS mode on the imx7d-sdb board.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Marek Vasut [Tue, 4 Apr 2023 19:25:10 +0000 (21:25 +0200)]
thermal: imx_tmu: Move architecture code into driver
Stop polluting the architecture directory with driver specific code,
move it into driver where it should be. Split the code slightly so
the MX8MM/MX8MN fuse readout and programming and MX8MP fuse readout
and programming are in their separate functions, and called in case
of matching SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Marek Vasut [Tue, 4 Apr 2023 19:25:09 +0000 (21:25 +0200)]
thermal: imx_tmu: Clean up all prints
Use dev_(dev, ...) for all printing and debug logging, since this
already includes the device name. Drop device name where duplicate.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Fedor Ross [Thu, 14 Apr 2022 16:36:23 +0000 (18:36 +0200)]
ARM: imx: Fix parsing of ROM log event IDs on iMX8M
It seems like the ROM log events for the iMX8M are not fully covered by
AN12853 i.MX ROMs Log Events, Rev. 0, May 2020. On iMX8M the ROM event
ID 0x82 seems to use parameter0 which stops the parsing because the end
of list is detected too early.
This patch adds ROM event ID 0x82 and skips the next word if ID 0x82 is
parsed.
Fixes: a5ee05cf71 ("ARM: imx: Pick correct eMMC boot partition from ROM log")
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tom Rini [Tue, 16 May 2023 15:23:30 +0000 (11:23 -0400)]
Merge tag 'efi-2023-07-rc3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2023-07-rc3
Documentation:
* update the description of signature algorithms
UEFI:
* fix unaligned access to GUID in HII database protocol
* fix launching EFI binaries loaded via semihosting
* fix filling of file path in loaded image protocol for non-block devices
Tom Rini [Tue, 16 May 2023 15:16:42 +0000 (11:16 -0400)]
Merge branch '2023-05-15-assorted-bugfixes'
- Merge in a long-standing fix for some exynos platforms, correct a
Kconfig description, fix some env issues, fix an issue in
devfdt_get_addr_size_index_ptr and look for "panel-timings" not
"panel-timing" per upstream binding.
Tom Rini [Tue, 16 May 2023 13:10:57 +0000 (09:10 -0400)]
Merge tag 'xilinx-for-v2023.07-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2023.07-rc3
.mailmap
- Fix Xilinx IDs
ZynqMP:
- Fix R5 split boot mode
- DT fixes - sync with Linux
Xilinx:
- Enable virtio and RNG support
- Enable ADI ethernet phy
SPI/Zynq:
- Fix dummy byte calculation
Manorit Chawdhry [Mon, 15 May 2023 06:52:42 +0000 (12:22 +0530)]
environment: ti: rproc: fix remoteproc environment variables
During refactor this seemed to have been missed.
Fixes: 65dbb128fb45 ("include: environment: ti: Use .env for environment variables")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Johan Jonker [Wed, 10 May 2023 21:48:44 +0000 (23:48 +0200)]
core: fdtaddr: use map_sysmem() as cast for the return (part 2)
For the devfdt_get_addr_size_index_ptr() function use
map_sysmem() function as cast for the return for use in
sandbox.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Raphael Gallais-Pou [Thu, 11 May 2023 14:36:52 +0000 (16:36 +0200)]
drivers: core: ofnode: fix typo in panel timing decode
In case where a single timing resolution is implemented in the
device-tree, the property is named "panel-timing", as specify
in Linux kernel binding file:
Documentation/devicetree/bindings/display/panel/panel-common.yaml
# Display Timings
panel-timing:
description:
Most display panels are restricted to a single resolution and
require specific display timings. The panel-timing subnode expresses those
timings.
$ref: panel-timing.yaml#
display-timings:
description:
Some display panels support several resolutions with different timings.
The display-timings bindings supports specifying several timings and
optionally specifying which is the native mode.
$ref: display-timings.yaml#
Fixes: 0347cc773270 ("drivers: core: ofnode: Add panel timing decode.")
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Christophe Leroy [Thu, 11 May 2023 06:16:49 +0000 (08:16 +0200)]
envtools lack extra settings since commit
86b9c3e4e4 ("env: Allow U-Boot scripts to be placed in
After converting my targets from CFG_EXTRA_ENV_SETTINGS to
CONFIG_EXTRA_ENV_TEXT as suggested by Tom, I discovered that
fw_setenv doesn't set the entire defaut environment anymore.
I tried to fix it with the below patch, but it fails qemu-x86 CI test,
see https://source.denx.de/u-boot/custodians/u-boot-mpc8xx/-/pipelines/16326
That's the only CI test that fails AFAICS.
Could you help with a solution ? This needs to be fixed.
Thanks
Christophe
---- >8 ----
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Subject: [RFC PATCH] envtools: Fix default environment
After converting some targets from CFG_EXTRA_ENV_SETTINGS to
CONFIG_EXTRA_ENV_TEXT, default environment embedded in
fw_env tool missed all extra settings.
Commit
86b9c3e4e4 ("env: Allow U-Boot scripts to be placed in
a .env file") restricted the inclusion of the content of that
file to builds without USE_HOSTCC.
But as mentionned in commit
79fc0c5f49 ("tools/env: cross-compile
fw_printenv without setting HOSTCC"), HOSTCC and USE_HOSTCC are
kept for code re-use.
Remove the restricting so that settings included in a .env
file are also added to fw_env tool.
Fixes: 86b9c3e4e4 ("env: Allow U-Boot scripts to be placed in a .env file")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Henrik Grimler [Tue, 9 May 2023 19:05:47 +0000 (21:05 +0200)]
samsung: common: do not reset if cros-ec uclass is missing
Otherwise non-ChromeOS samsung devices, like the odroid boards, are
stuck in a bootloop if CONFIG_CROS_EC is not enabled:
<...>
MMC: SAMSUNG SDHCI: 2, EXYNOS DWMMC: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment
cros-ec communications failure -96
Please reset with Power+Refresh
Cannot init cros-ec device
resetting ...
Issue started after commit
e44d7e73fe0d ("dm: core: Switch
uclass_*_device_err to use uclass_*_device_check").
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Henrik Grimler [Tue, 9 May 2023 19:05:46 +0000 (21:05 +0200)]
Revert "mmc: s5p_sdhci: unset the SDHCI_QUIRK_BROKEN_R1B"
This reverts commit
a034ec06ff1d558bbe11d5ee05edbb4de3ee2215.
Commit
4a3ea75de4c5 ("Revert "mmc: sdhci: set to INT_DATA_END when
there are data"") reverted the alternative fix that was added for
Exynos 4 devices, causing an error when trying to boot from an sdcard:
<...>
Loading Environment from MMC... sdhci_send_command: Timeout for status update!
mmc fail to send stop cmd
<...>
Re-add the quirk to allow booting from sdcards again.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
John Keeping [Tue, 9 May 2023 11:02:50 +0000 (12:02 +0100)]
video: tweak CONFIG_SPL_VIDEO description
Make it clear that this is the SPL option to avoid potential confusion
when the description for CONFIG_SPL_VIDEO is the same as that for
CONFIG_VIDEO.
Signed-off-by: John Keeping <john@metanate.com>
Tom Rini [Mon, 15 May 2023 12:33:16 +0000 (08:33 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-cfi-flash
- cfi: respect reg address length (Nuno)
Nuno Sá [Thu, 11 May 2023 11:19:50 +0000 (13:19 +0200)]
mtd: cfi: respect reg address length
flash_get_size() will get the flash size from the device itself and go
through all erase regions to read protection status. However, the device
mappable region (eg: devicetree reg property) might be lower than the
device full size which means that the above cycle will result in a data
bus exception. This change fixes it by reading the 'addr_size' during
probe() and also use that as one possible upper limit.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Algapally Santosh Sagar [Wed, 26 Apr 2023 06:01:04 +0000 (00:01 -0600)]
.mailmap: Map all Xilinx users mail ids to AMD
The mail ids of all the current Xilinx users are to be mapped to AMD
following the merger with AMD. The mailmap file is updated accordingly.
The ids of Marek Behún and Michal Simek are taken as reference.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230426060104.10412-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Algapally Santosh Sagar [Wed, 26 Apr 2023 06:01:03 +0000 (00:01 -0600)]
.mailmap: Sort the mailmap ids in dictionary order
The mailmap ids are not arranged in the dictionary order. So, sort the
mailmap ids in the dictionary order.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230426060104.10412-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Stefan Herbrechtsmeier [Thu, 27 Apr 2023 06:53:54 +0000 (08:53 +0200)]
Revert "spi: zynq_qspi: Use dummy buswidth in dummy byte calculation"
This reverts commit
e09784728689de7949d4cdd559a9590e0bfcc702. The
commit wrongly divides the dummy bytes by dummy bus width to calculate
the dummy bytes. The framework already converts the dummy cycles to the
number of bytes and the controller use the SPI flash command to
determine the dummy cycles via the address width.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230427065355.7413-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ashok Reddy Soma [Thu, 20 Apr 2023 08:56:45 +0000 (02:56 -0600)]
arm64: versal: Enable ADIN ethernet phy
Versal VEK280 board has Analog Devices ethernet phy. So, enable
CONFIG_PHY_ADIN config in Versal defconfig.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230420085645.21260-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ashok Reddy Soma [Thu, 20 Apr 2023 08:56:44 +0000 (02:56 -0600)]
arm64: zynqmp: Enable ADIN ethernet phy
Some of the Kria SOM and ZynqMP boards are using Analog Devices ethernet
phy. So, enable CONFIG_PHY_ADIN for all ZynqMP platforms.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230420085645.21260-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Michal Simek [Wed, 12 Apr 2023 14:30:27 +0000 (16:30 +0200)]
arm64: zynqmp: Fix User MTD partition size
The commit
c8630167e0dc ("arm64: zynqmp: Add mtd partition for secure OS
storage area") didn't update User partition size that's why size was beyond
actual device size.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/0a56405553b87a75e066cd71697cafe7c1c97eef.1681309812.git.michal.simek@amd.com
Ashok Reddy Soma [Wed, 5 Apr 2023 13:06:45 +0000 (15:06 +0200)]
arm64: zynqmp: Fix issue of apps executing from R5 core 1
In current implementation, applications can execute only on R5 core 0.
The boot address for R5 core 1 is not supplied. Pass TCM address for
R5 core 1 based on the argument to fix the issue.
Remove incomplete comment.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/da865717d26648ab7a84345ca8749712efdddee5.1680699999.git.michal.simek@amd.com
Michal Simek [Tue, 28 Mar 2023 07:21:33 +0000 (09:21 +0200)]
ARM: zynq: Sync Microzed board with Linux kernel
Fix model name, node locations and also add pinctrl description for usb.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/3295fde73db13a712b65f4967eb5f39ced895ad4.1679988091.git.michal.simek@amd.com
Michal Simek [Tue, 28 Mar 2023 07:17:31 +0000 (09:17 +0200)]
ARM: zynq: Switch from earlyprintk to earlycon
Switch to earlycon which is preffered over earlyprintk.
It is also sync with Linux kernel (zynq-microzed).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d280fa18068f80412cf12c235c5245651e7062e2.1679987839.git.michal.simek@amd.com
Michal Simek [Thu, 23 Mar 2023 14:52:11 +0000 (15:52 +0100)]
xilinx: Enable virtio mmio transport and devices
Qemu can create virtio mmio transports and passing devices through it
that's why enable virtio by default on all arm64 based SoCs.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a2ee18e7e8c1881ce72c5cd13127794a02410696.1679583129.git.michal.simek@amd.com
Neal Frager [Thu, 23 Mar 2023 08:25:06 +0000 (08:25 +0000)]
arch: arm: zynqmp: mp.c: tcminit halt both cores in split mode
The "zynqmp tcminit split" command should halt both cores and not just RPU1
when configuring the TCM memory for split mode.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Link: https://lore.kernel.org/r/20230323082506.31576-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Tom Rini [Sun, 14 May 2023 15:29:45 +0000 (11:29 -0400)]
Merge branch 'master_rzn1/rzn1' of https://source.denx.de/u-boot/custodians/u-boot-sh
- R-Car RZN1 support
Tom Rini [Sun, 14 May 2023 15:27:18 +0000 (11:27 -0400)]
Merge branch '2023-05-13-bootstd-updates-and-improvements'
- Assorted bootstd fixes and cleanups. This should fix problems with
Debian, and make script-based distributions work when BOOTMETH_DISTRO
is enabled now (as BOOTMETH_DISTRO was renamed and then reintroduced).
Simon Glass [Wed, 10 May 2023 22:34:47 +0000 (16:34 -0600)]
bootstd: Create a new BOOTMETH_DISTRO
We cannot be sure what bootmeth a distro will need to use. Add a new
BOOTMETH_DISTRO option which collects these together. Select this from
BOOTSTD_DEFAULTS so that it is clear what is needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make BOOTMETH_EFILOADER depend on EFI_LOADER, select if EFI_LOADER]
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 10 May 2023 22:34:46 +0000 (16:34 -0600)]
bootstd: Rename distro and syslinux to extlinux
We use the terms 'distro' to mean extlinux but they are not really the
same. 'Distro' could refer to any method of booting a distribution,
whereas extlinux is a particular method.
Also we sometimes use syslinux, but it is better to use the same term in
all cases.
Rename distro to syslinux and also update bootstd uses of syslinux to use
extlinux instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 10 May 2023 22:34:26 +0000 (16:34 -0600)]
bootstd: Tidy up reporting of errors
In a few cases the error handling is not quite right. Make sure we
return the actual error in distro_efi_read_bootflow_file() rather than
-EINVAL. Return -IO when a file cannot be read. Also show the error name
if available.
This does not change operation, but does make it easier to diagnose
problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 6 May 2023 14:27:09 +0000 (08:27 -0600)]
bootstd: Correct default boot command
The patch to relax flag requirements was not accepted[1], so we still have
to have separate bootcommands depending on CMD_BOOTFLOW_FULL.
The previous attempt at this did not work, since it used the wrong name
for the options.
Fix this and change the message to mention BOOTSTD_FULL since this affects
not just the flags, but all functionality, so is more likely what the user
wants.
Drop the useless condition on CMD_BOOTFLOW_FULL while we are here.
[1] https://patchwork.ozlabs.org/project/uboot/patch/
20230329071655.
1959513-2-sjg@chromium.org/
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: a91492b6e9c ("bootstd: Provide a default command")
Simon Glass [Sat, 6 May 2023 02:03:05 +0000 (20:03 -0600)]
bootstd: Require HUSH_PARSER for script booting
Armbian uses a script which needs the HUSH parser. It is likely that
other distros will do the same. Enable it by default, just in case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Simon Glass [Sat, 6 May 2023 02:03:04 +0000 (20:03 -0600)]
bootstd: usb: Avoid initing USB twice
This causes crashes on some boards, e.g. rockpro64. In any case, we
should not do it.
Check the usb_started flag to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sat, 6 May 2023 02:03:03 +0000 (20:03 -0600)]
usb: Tidy up the usb_start flag
This should be declared in a header file so that type-checking works
correctly.
Add a single declaration to usb.h and remove the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Simon Glass [Fri, 28 Apr 2023 19:18:09 +0000 (13:18 -0600)]
bootstd: Work around missing partition 1
If there is no partition numbered 1, we decide that there are no
partitions at all. That may not be correct, since at least one Debian
installed has just a single partition numbered 2.
Continue searching up to partition 3, just in case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Sat, 13 May 2023 08:36:21 +0000 (10:36 +0200)]
efi_loader: fix efi_dp_from_file()
* When called from efi_dp_from_name() we miss to append the filename
for non-block devices.
* expand_media_path() could be simplified by using efi_dp_from_file to
prepend the device path of the boot device.
This can be avoided by passing a device path to efi_dp_from_file() instead
of a block device descriptor and a partition number.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sat, 13 May 2023 08:30:43 +0000 (10:30 +0200)]
efi_loader: simplify efi_dp_from_name()
Don't do the same check and assignment in multiple places.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sat, 13 May 2023 08:22:21 +0000 (10:22 +0200)]
efi_loader: error code efi_dp_from_name()
Use EFI_OUT_OF_RESOURCES if the device path cannot be constructed.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sat, 13 May 2023 08:18:24 +0000 (10:18 +0200)]
efi_loader: clean up efi_dp_from_file
* Improve variable name usage: Use pos instead of buf to indicate the
current position in a buffer.
* Avoid double assignment in a single code line.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sat, 13 May 2023 08:00:55 +0000 (10:00 +0200)]
efi_loader: duplicate code in efi_dp_from_name
efi_dp_from_name() has duplicate code to replace slash by backslash.
path_to_uefi() called by efi_dp_from_file() already does this.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sat, 13 May 2023 07:55:26 +0000 (09:55 +0200)]
efi_loader: avoid #ifdef in efi_dp_from_name()
According to our coding style guide #ifdef should be avoided.
Use IS_ENABLED() instead.
Sort string comparisons alphabetically.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Fri, 12 May 2023 18:18:10 +0000 (20:18 +0200)]
efi_loader: support booting semihosting file
Executing an EFI binary fails for files loaded via semihosting.
Construct a dummy device path for EFI binaries loaded via semihosting.
A future complete solution may include the creation of a handle with a
simple file system protocol.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Fri, 12 May 2023 19:23:15 +0000 (21:23 +0200)]
efi_loader: print file path w/o boot device
Helloworld.efi should print the file path even if the boot device is
not set.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Ilias Apalodimas [Thu, 11 May 2023 16:40:35 +0000 (19:40 +0300)]
efi_loader: Fix warnings for unaligned accesses
Tom reports that when building with clang we see this warning:
field guid within 'struct efi_hii_keyboard_layout' is less aligned than 'efi_guid_t' and is usually due to 'struct efi_hii_keyboard_layout' being packed, which can lead to unaligned accesses [-Wunaligned-access]
This happens because 'struct efi_hii_keyboard_layout' is defined as
packed and thus has 1-byte alignment but efi_guid_t is a type that
requires greater alignment than that.
However the EFI spec describes the EFI_GUID as
"128-bit buffer containing a unique identifier value.
Unless otherwise specified"
So convert the efi_guid_t -> u8 b[16] here and skip the alignment
requirements. Since the struct is packed to begin with, it makes no
difference on the final memory layout.
Suggested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sun, 7 May 2023 06:39:34 +0000 (08:39 +0200)]
fwu: fix config FWU_MULTI_BANK_UPDATE
Symbol CONFIG_EFI_SETUP_EARLY does not exist anymore.
CONFIG_FWU_MULTI_BANK_UPDATE without CONFIG_FWU_MDATA results in
lib/fwu_updates/fwu.c:49: undefined reference to `fwu_get_mdata'
Fixes: 86794052418b ("FWU: Add support for the FWU Multi Bank Update feature")
Fixes: 023d9c93932c ("efi_loader: remove CONFIG_EFI_SETUP_EARLY")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Baruch Siach [Tue, 2 May 2023 10:21:46 +0000 (13:21 +0300)]
doc: devicetree: fix u-boot.bin filename typo
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Baruch Siach [Tue, 2 May 2023 04:47:31 +0000 (07:47 +0300)]
doc: signature: trim the future work list
Since U-Boot supports more RSA/SHA variants, as well as ECDSA, remove
these items from the TODO list.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Baruch Siach [Tue, 2 May 2023 04:47:30 +0000 (07:47 +0300)]
doc: signature: describe how to enable ECDSA
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Baruch Siach [Tue, 2 May 2023 04:47:29 +0000 (07:47 +0300)]
doc: signature: update algorithm addition description
U-Boot now uses the U_BOOT_CRYPTO_ALGO() macro.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Baruch Siach [Tue, 2 May 2023 04:47:28 +0000 (07:47 +0300)]
doc: signature: update algorithms support description
U-Boot supports more hash and verification algorithms these days.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Ralph Siemsen [Sat, 13 May 2023 01:36:58 +0000 (21:36 -0400)]
doc: renesas: add Renesas board docs
As a starting point, list all currently supported Renesas boards.
For the RZ/N1 board, add details about booting and flashing.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Ralph Siemsen [Sat, 13 May 2023 01:36:57 +0000 (21:36 -0400)]
tools: spkgimage: add Renesas SPKG format
Renesas RZ/N1 devices contain BootROM code that loads a custom SPKG
image from QSPI, NAND or USB DFU. Support this format in mkimage tool.
SPKGs can optionally be signed, however creation of signed SPKG is not
currently supported.
Example of how to use it:
tools/mkimage -n board/schneider/rzn1-snarc/spkgimage.cfg \
-T spkgimage -a 0x20040000 -e 0x20040000 \
-d u-boot.bin u-boot.bin.spkg
The config file (spkgimage.cfg in this example) contains additional
parameters such as NAND ECC settings.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Ralph Siemsen [Sat, 13 May 2023 01:36:56 +0000 (21:36 -0400)]
board: schneider: add RZN1 board support
Add support for Schneider Electric RZ/N1D and RZ/N1S boards, which
are based on the Reneasas RZ/N1 SoC devices.
The intention is to support both boards using a single defconfig, and to
handle the differences at runtime.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Ralph Siemsen [Sat, 13 May 2023 01:36:55 +0000 (21:36 -0400)]
ARM: rmobile: Add support for Renesas RZ/N1 SoC
The RZ/N1 is a family of SoC devices from Renesas, featuring:
* ARM Cortex-A7 CPU (single/dual core) and/or Cortex-M3
* Integrated SRAM up to 6MB
* Integrated gigabit ethernet switch
* Optional DDR2/3 controller
* I2C, SPI, UART, NAND, QSPI, SDIO, USB, CAN, RTC, LCD
Add basic support for this family, modeled on the existing RZA1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Ralph Siemsen [Sat, 13 May 2023 01:36:54 +0000 (21:36 -0400)]
ARM: dts: add devicetree for Renesas RZ/N1 SoC
This is taken directly from Linux kernel 6.3
(commit
457391b0380335d5e9a5babdec90ac53928b23b4)
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Ralph Siemsen [Sat, 13 May 2023 01:36:53 +0000 (21:36 -0400)]
ram: cadence: add driver for Cadence EDAC
Driver for Cadence EDAC DDR controller, as found in the Renesas RZ/N1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Ralph Siemsen [Sat, 13 May 2023 01:36:52 +0000 (21:36 -0400)]
pinctrl: renesas: add R906G032 driver
Pinctrl/pinconf driver for Renesas RZ/N1 (R906G032) SoC.
This is quite rudimentary right now, and only supports applying a
default pin configuration as specified by the device tree.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Ralph Siemsen [Sat, 13 May 2023 01:36:51 +0000 (21:36 -0400)]
clk: renesas: add R906G032 driver
Clock driver for the Renesas RZ/N1 SoC family. This is based on
Linux kernel 6.2.y drivers/clk/renesas/r9a06g032-clocks.c as found in
commit
02693e11611e ("clk: renesas: r9a06g032: Repair grave increment error"),
with the following additional patch series applied:
https://lore.kernel.org/linux-renesas-soc/
20230301215520.828455-1-ralph.siemsen@linaro.org/
Notable difference: this version avoids allocating a 'struct clk'
for each clock source, as this is problematic before relocation.
Instead, it uses the same approach as existing Renesas R-Car Gen2/3
clock drivers, using a temporary structure filled on-the-fly.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Ralph Siemsen [Sat, 13 May 2023 01:36:50 +0000 (21:36 -0400)]
clk: renesas: prepare for non R-Car clock drivers
Add new CONFIG_CLK_RCAR to control compilation of shared code for R-Car
clock drivers (renesas-cpg-mssr.c). Enable this for R-Car Gen2 and 3.
This is necessary so that CONFIG_CLK_RENESAS can be enabled, allowing
recursion into the drivers/clk/reneasas directory, without bringing in
the R-Car support code. The support code contains platform specific
access (TMU_BASE) which is not needed on other Renesas devices such as
RZ/N1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>