Chris Morgan [Tue, 2 Jan 2024 15:46:54 +0000 (09:46 -0600)]
doc: board: anbernic: Update rgxx3 to add new boards
Update the RGxx3 documentation to note that it now supports the
RG-ARC-D, RG-ARC-S, Powkiddy RK2023, and Powkiddy RGB30. Also update
verbiage around panel detection to note that it is no longer hard coded
to the RG503.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Tue, 2 Jan 2024 15:46:53 +0000 (09:46 -0600)]
board: rockchip: Add support for new boards to RGxx3
Add support for the Anbernic RG-ARC-D, Anbernic RG-ARC-S, Powkiddy
RK2023, and Powkiddy RGB30 to the Anbernic RGxx3. While the Powkiddy
devices are manufactured by Powkiddy instead of Anbernic,
the hardware is so similar they can all use the same bootloader.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Tue, 2 Jan 2024 15:46:52 +0000 (09:46 -0600)]
rockchip: board: Add board_rng_seed() for all Rockchip devices
Allow all rockchip devices to use the hardware RNG to seed Linux
RNG.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chris Morgan [Tue, 2 Jan 2024 15:46:48 +0000 (09:46 -0600)]
board: rockchip: Refactor panel auto-detect code
Make the inability to detect a panel using the auto detection code not
fail the entire boot process. This means that if the panel ID cannot
be read we don't set an environment variable for the panel, and if an
environment variable for the panel is not set we don't attempt to
update the compatible string. Changes to the code also ensure that
when there are multiple compatible strings required for the panel
we use them both, which solves some issues that will pop up soon
for the Linux driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Sun, 7 Jan 2024 18:18:33 +0000 (18:18 +0000)]
rockchip: rk3328: Set efuse auto mode and timing control
Reading from efuse return zero when mainline TF-A is used.
=> dump_efuse
00000000: 00 00 00 00 ....
00000004: 00 00 00 00 ....
00000008: 00 00 00 00 ....
0000000c: 00 00 00 00 ....
00000010: 00 00 00 00 ....
00000014: 00 00 00 00 ....
00000018: 00 00 00 00 ....
0000001c: 00 00 00 00 ....
However, when vendor TF-A blobs is used reading from efuse works.
Change to use auto mode, enable finish and auto access err interrupts
and set timing control using same values that vendor TF-A blob use to
fix this.
With this efuse can be read when either of mainline TF-A or vendor blob
is used.
=> dump_efuse
00000000: 52 4b 33 82 RK3.
00000004: 00 fe 21 55 ..!U
00000008: 52 4b 57 34 RKW4
0000000c: 35 30 32 39 5029
00000010: 00 00 00 00 ....
00000014: 08 25 0c 0f .%..
00000018: 02 0d 08 00 ....
0000001c: 00 00 f0 00 ....
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Quentin Schulz [Wed, 17 Jan 2024 17:59:13 +0000 (18:59 +0100)]
rockchip: theobroma-systems: fix modified boot_targets detection
U-Boot proper automatically modifies boot_targets to swap the order in
which MMC storage media are used for standard boot based on which MMC
storage medium was used to load U-Boot proper. This is however only done
if the user has not changed it manually, therefore a check between the
default and current value is done.
This used to work fine until the migration to standard boot where
boot_targets value size in the default environment went above the 32
characters that env_get_default function can return, thus resulting in a
truncated variable.
Therefore the check between default and current value would always fail.
By using the newly added env_get_default_into function, a buffer of
the appropriate size can be allocated on the stack to get the whole
value of boot_targets in the default environment and thus fixing the
check.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Quentin Schulz [Wed, 17 Jan 2024 17:59:12 +0000 (18:59 +0100)]
env: migrate env_get_default to call env_get_default_into
Since both functions share a similar goal and env_get_default_into can
do what env_get_default wants to do with specific arguments, let's make
env_get_default call env_get_default_into so as to avoid code
duplication.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Quentin Schulz [Wed, 17 Jan 2024 17:59:11 +0000 (18:59 +0100)]
env: allow to copy value from default environment into a buffer
env_get_default suffers from a particular issue int that it can only
return a value truncated to gd->env_buf (32) characters. This may be
enough for most variables but it isn't for others, so let's allow users
to provide a preallocated buffer to copy the value into instead,
allowing for more control, though it'll still be truncated if the value
size is bigger than the preallocated buffer.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Quentin Schulz [Wed, 17 Jan 2024 17:59:10 +0000 (18:59 +0100)]
rockchip: ringneck-px30/puma-rk3399: factor out storage medium selection
Ringneck PX30 and Puma RK3399 both have the same expectation with regard
to bootstd device order and U-Boot environment storage device, except
that Puma RK3399 also supports SPI Flash.
Let's move all of this into a common file where common logic can be put.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Quentin Schulz [Wed, 17 Jan 2024 17:59:09 +0000 (18:59 +0100)]
rockchip: puma-rk3399: do not hardcode MMC controller paths
To prepare to put the similar logic around storage medium selection for
Ringneck PX30 and Puma RK3399 in common, let's not use hardcoded paths
but use uclass functions instead to find udevice based on their DT node
full path.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Quentin Schulz [Wed, 17 Jan 2024 17:59:08 +0000 (18:59 +0100)]
rockchip: ringneck-px30: do not hardcode MMC controller paths
To prepare to put the similar logic around storage medium selection for
Ringneck PX30 and Puma RK3399 in common, let's not use hardcoded paths
but use uclass functions instead to find udevice based on their DT node
full path.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Joshua Riek [Wed, 10 Jan 2024 01:30:24 +0000 (20:30 -0500)]
board: rockchip: Add the Turing RK1 SoM
The Turing RK1 is a Rockchip RK3588 based SoM from Turing Machines.
Specifications:
Rockchip RK3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16/32GB memory LPDDR4x
Mali G610MC4 GPU
32GB eMMC HS400
2x USB 2.0, 2x USB 3.0
2x MIPI CSI 4x lanes
1x MIPI-DSI DPHY 2x lanes
PCIe 2.0 x1, PCIe 3.0 x4
1x HDMI 2.1 output, 1x DP 1.4 output
Gigabit Ethernet
Size: 69.6mm x 45mm (260-pin SO-DIMM connector)
Kernel commit:
2806a69f3fef ("arm64: dts: rockchip: Add Turing RK1 SoM support")
Signed-off-by: Joshua Riek <jjriek@verizon.net>
Tested-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Fri, 17 Nov 2023 23:24:37 +0000 (23:24 +0000)]
rockchip: rk3588s-orangepi-5: Build SPI image
Enable building of the SPI image, u-boot-rockchip-spi.bin, now that we
know what bootsource id values BootRom use for SPI flash on RK3588.
Fixes: 28c5f941edf7 ("board: rockchip: Add Xunlong Orange Pi 5")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Slawomir Stepien [Fri, 17 Nov 2023 23:24:36 +0000 (23:24 +0000)]
rockchip: rk3588-orangepi-5-plus: Build SPI image
Enable building of the SPI image, u-boot-rockchip-spi.bin, now that we
know what bootsource id values BootRom use for SPI flash on RK3588.
Fixes: b51cf8bb09b6 ("board: rockchip: Add Xunlong Orange Pi 5 Plus")
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
John Clark [Fri, 17 Nov 2023 23:24:35 +0000 (23:24 +0000)]
rockchip: rk3588-nanopc-t6: Build SPI image
Enable building of the SPI image, u-boot-rockchip-spi.bin, now that we
know what bootsource id values BootRom use for SPI flash on RK3588.
Fixes: b0b8086898f8 ("board: rockchip: add FriendlyElec NanoPC-T6 rk3588 board")
Signed-off-by: John Clark <inindev@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Fri, 17 Nov 2023 23:24:34 +0000 (23:24 +0000)]
rockchip: rk3588: Fix boot from SPI flash
The commit
fd6e425be243 ("rockchip: rk3588-rock-5b: Enable boot from SPI
NOR flash") added a new BROM_BOOTSOURCE_SPINOR_RK3588 with value 6.
At the time the reason for this new bootsource id value 6 was unknown.
We now know that the BootRom on RK3588 use different bootsource id
values depending on the iomux used by the flash spi controller, and not
by the type of spi nor or spi nand flash used.
Add the following enum values and use them for RK3588 boot_devices.
- BROM_BOOTSOURCE_FSPI_M0 = 3
- BROM_BOOTSOURCE_FSPI_M1 = 4
- BROM_BOOTSOURCE_FSPI_M2 = 6
Fixes: fd6e425be243 ("rockchip: rk3588-rock-5b: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Slawomir Stepien <sst@poczta.fm>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tianling Shen [Sat, 23 Dec 2023 04:00:07 +0000 (12:00 +0800)]
board: rockchip: Add support for FriendlyARM NanoPi R2C Plus
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
The device tree is taken from the kernel v6.5.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Wed, 27 Dec 2023 12:06:47 +0000 (13:06 +0100)]
arm: dts: rockchip: rk3288: move to 64 bit reg size
To make automatic Rockchip DT syncing possible from Linux to U-boot prepare
rk3288.dtsi by moving to 64 bit reg size.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Hugh Cole-Baker [Tue, 26 Dec 2023 16:43:30 +0000 (16:43 +0000)]
rockchip: rk35xx: expand space for decompressed kernel
An uncompressed 6.7.0-rc1 Linux kernel Image built with the arm64
defconfig is about 40MB. This does not fit in to the space between
kernel_comp_addr_r and fdt_addr_r, so when uncompressing an Image.gz
to this size, the FDT will be overwritten. Rearrange addresses to have
128MiB for the kernel and its decompression buffer, then devicetree,
overlay and ramdisk at the end.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Sun, 12 Nov 2023 17:48:58 +0000 (17:48 +0000)]
rockchip: board: Remove dwc3 usb init and gadget handler functions
Remove board_usb_init() and dm_usb_gadget_handle_interrupts() functions
related to dwc3, they use e.g. a hard-coded reg address for RK3399 and
are obsolete with use of DM_USB_GADGET.
Use of DM_USB_GADGET, USB_DWC3_GENERIC and USB_DWC3_GADGET have replaced
same feature provided by the removed functions on RK3399 boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Sun, 12 Nov 2023 17:48:57 +0000 (17:48 +0000)]
configs: rockchip: Use dwc3-generic driver on RK3328 and RK3399
Complete the transition away from xhci-dwc3 and dwc3-of-simple drivers
and change to use the dwc3-generic driver on remaining RK3328 and RK3399
boards.
MISC, USB_DWC3 and USB_DWC3_GENERIC is enabled on boards that used to
enable USB_XHCI_DWC3. USB_XHCI_DWC3 is dropped from updated boards along
with the default y of USB_XHCI_DWC3_OF_SIMPLE.
There is no intended change in functionality with this changes, USB 3.0
is expected to continue same as before this change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini [Thu, 18 Jan 2024 16:38:25 +0000 (11:38 -0500)]
Revert "test: hush: dollar: fix bugous behavior"
What we were doing here amounts to simplifying the code for the new hush
parser, and the workarounds are required when using the old one. As we
have returned to having the old parser be default for now, we must undo
this so that the test passes again.
This reverts commit
6c2f753f4ad3dcee60190949d1286736a6d51d17.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 18 Jan 2024 14:07:25 +0000 (09:07 -0500)]
Revert "cmd: Set modern hush as default shell"
Currently at least two SoC families are able to cause a crash using
their regular boot scripts, with the new parser. For now, revert to the
old parser as default.
This reverts commit
78912cfde281146d28254b230ecaa9b06722e6ff.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 18 Jan 2024 14:05:38 +0000 (09:05 -0500)]
Revert "test/py: net: Add dhcp abort test"
In practice, as this test defaults to enabled rather than disabled, too
many platforms now fail.
This reverts commit
d8364738623ff47dd2321dd68da310abb58fe861.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 17 Jan 2024 20:04:50 +0000 (15:04 -0500)]
CI: Move to latest Ubuntu "Jammy" tag
Move to the latest "Jammy" tag from Ubuntu.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 17 Jan 2024 22:12:36 +0000 (17:12 -0500)]
test: test_trace.py: Have trace-cmd report always use -l
With newer versions of trace-cmd the report subcommand will have
different output from before if we do or do not pass -l. However, with
the -l flag passed our put is consistent here. This updates our regular
expressions and comments for this as well now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 17 Jan 2024 20:06:54 +0000 (15:06 -0500)]
test/py/requirements.txt: Update packaging requirement
Update packaging to be version 23.2 to match our Sphinx requirements.
This will let us build a pip cache out of both of our requirements.txt
files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Heinrich Schuchardt [Fri, 12 Jan 2024 02:17:57 +0000 (03:17 +0100)]
docker: build QEMU v8.2.0
ACPI support for RISC-V requires a recent QEMU.
Upgrade the used QEMU to v8.2.0.
QEMU commit
0c7ffc977195 ("hw/net: cadence_gem: Fix MDIO_OP_xxx values")
is needed to fix the Ethernet PHY driver used by the emulated SiFive
Unleashed Board emulation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tom Rini [Wed, 17 Jan 2024 14:27:43 +0000 (09:27 -0500)]
Merge tag 'xilinx-for-v2024.04-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.04-rc1-v2
xilinx:
- Enable NFS, WGET, DNS and BLKMAP by default
zynqmp:
- Support new power-management node
- Remove multiple blank lines from DTSes
- Wire multiboot with DFU infrastructure
- Fix i2c-gpio pinctrl group name
- SOM DT changes (phy on kd240, kv260 cleanups
- Cleanup i2c bus on zcu1285
- DT cleanup (fix node names not to use _)
- Fix USB interrupts
- Cleanup zcu100 DT
- Add support for kaslr-seed
zynqmp_r5:
- Fix W=1 issue with missing dir
tools:
- Improve zynqmpimage mkimage support
Tom Rini [Wed, 17 Jan 2024 14:27:23 +0000 (09:27 -0500)]
Merge tag 'efi-2024-04-rc1-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Documentation:
* add generated index to table of contents
* create index entries for commands
* update Python packages used to build the documentation
* fix typos in dfu documentation
UEFI:
* split unrelated code from efi_bootmgr.c
* rename CONFIG_BOOTEFI_BOOTMGR to CONFIG_EFI_BOOTMGR
* net: tftp: remove explicit EFI configuration dependency
* fs: remove explicit EFI configuration dependency
Other:
* Add Goldfish RTC driver and make it available on RISC-V QEMU
Tom Rini [Wed, 17 Jan 2024 14:12:27 +0000 (09:12 -0500)]
Merge branch '2024-01-16-assorted-updates-and-improvements'
- Add more pytests to exercise functionality on real hardware, cleanup
and add tests around "cp"/memmove, add phyCORE-AM62x and Phytium
Pe2201 platforms, Nuvoton NPCM BMC reset driver and improve QEMU
SMBIOS support
Tom Rini [Fri, 5 Jan 2024 19:43:43 +0000 (14:43 -0500)]
test.py: Update pycryptodomex to address CVE-2023-52323
The version of pycryptodomex that we use is vulnerable to this CVE.
While not likely an issue for us, let us upgrade to be on the safe side.
Reported-by: GitHub dependabot
Signed-off-by: Tom Rini <trini@konsulko.com>
Rasmus Villemoes [Wed, 3 Jan 2024 10:47:10 +0000 (11:47 +0100)]
doc: drop references to non-existing CONFIG_MEM_SUPPORT_64BIT_DATA
Such a config option does not exist. Rephrase, and avoid mentioning
MEM_SUPPORT_64BIT_DATA, which is an implementation detail.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Wed, 3 Jan 2024 10:47:09 +0000 (11:47 +0100)]
README: drop mention of MEM_SUPPORT_64BIT_DATA
The first sentence is half-way true; the macro is always defined, but
has the value 0 or 1.
The second is outright false. A lot of code guarded by
MEM_SUPPORT_64BIT_DATA uses a "ulong" to store values, so if
sizeof(long) is not 8, that code would probably compile, but not work
at all as expected.
It would probably be possible to make all such code explicitly use u64
and thus make it work on 32 bit targets, but until that is done, do
not pretend that it's ok to override the automatic value of
MEM_SUPPORT_64BIT_DATA.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Wed, 3 Jan 2024 10:47:08 +0000 (11:47 +0100)]
cmd/mem.c: fix wrong use of ifdef, drop pointless SUPPORT_64BIT_DATA macro
The macro MEM_SUPPORT_64BIT_DATA is always defined, as either 1 or 0,
so using "#ifdef MEM_SUPPORT_64BIT_DATA" doesn't do what one
expects.
This means that currently all 32 bit targets get compiled with the .q
suffix mentioned in the help text, while it doesn't actually work.
Use the proper "#if" instead.
There's really no point defining another similarly-named macro with
exactly the same value, so just use MEM_SUPPORT_64BIT_DATA throughout.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Wed, 3 Jan 2024 10:47:07 +0000 (11:47 +0100)]
test: add test of "cp" shell command
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Heinrich Schuchardt [Sat, 30 Dec 2023 23:53:01 +0000 (00:53 +0100)]
riscv: qemu: imply GOLDFISH_RTC
QEMU's virt board provides an emulated Goldfish RTC. Enable the driver by
default.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sat, 30 Dec 2023 23:53:00 +0000 (00:53 +0100)]
rtc: driver for Goldfish RTC
The Goldfish RTC is a virtual device which may be supplied by QEMU.
It is enabled by default on QEMU's RISC-V virt machine.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
AKASHI Takahiro [Wed, 17 Jan 2024 04:39:44 +0000 (13:39 +0900)]
fs: remove explicit efi configuration dependency
Now it is clear that the feature actually depends on efi interfaces,
not "bootefi" command. efi_set_bootdev() will automatically be nullified
if necessary efi component is disabled.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Wed, 17 Jan 2024 04:39:43 +0000 (13:39 +0900)]
net: tftp: remove explicit efi configuration dependency
Now it is clear that the feature actually depends on efi interfaces,
not "bootefi" command. efi_set_bootdev() will automatically be nullified
if necessary efi component is disabled.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AKASHI Takahiro [Wed, 17 Jan 2024 04:39:42 +0000 (13:39 +0900)]
efi_loader: rename BOOTEFI_BOOTMGR to EFI_BOOTMGR
At this point, EFI boot manager interfaces is fully independent from
bootefi command. So just rename the configuration parameter.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Wed, 17 Jan 2024 04:39:41 +0000 (13:39 +0900)]
efi_loader: split unrelated code from efi_bootmgr.c
Some code moved from cmd/bootefi.c is actually necessary only for "bootefi
<addr>" command (starting an image manually loaded by a user using U-Boot
load commands or other methods (like JTAG debugger).
The code will never been opted out as unused code by a compiler which
doesn't know how EFI boot manager is implemented. So introduce a new
configuration, CONFIG_EFI_BINARY_EXEC, to enforce them opted out
explicitly.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Heinrich Schuchardt [Sun, 14 Jan 2024 13:18:23 +0000 (14:18 +0100)]
doc: update requirements.txt
Update requirements.txt to most current packages as produced by
python3 -m pip install six sphinx-rtd-theme sphinx-prompt
python3 -m pip freeze
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Heinrich Schuchardt [Sun, 14 Jan 2024 13:18:22 +0000 (14:18 +0100)]
doc: import Sphinx theme.css and pygments.css
We want to override the Sphinx theme only partially. So we need to
import the Sphinx theme.css. Cf.
https://docs.readthedocs.io/en/stable/guides/adding-custom-css.html
We also need to import the pygments.css for syntax highlighing.
Use sans-serif for body.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sun, 14 Jan 2024 13:18:21 +0000 (14:18 +0100)]
doc: update theme_overrides.css
Update theme_overrides.css from Linux v6.7.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sun, 14 Jan 2024 13:18:20 +0000 (14:18 +0100)]
doc: add sphinx_rtd_theme extension
Newer versions of sphinx_rtd_theme require to add sphinx_rtd_theme to the
list of extensions. Cf.
https://github.com/readthedocs/readthedocs.org/pull/9654
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Oliver Faso [Sun, 14 Jan 2024 13:18:19 +0000 (14:18 +0100)]
docs/sphinx: Explicitly convert Sphinx paths to str
Sphinx 7.2+ is switching to using pathlib.Path
instead of str to represent paths. This fixes the
current deprecation warnings and eventual breakage.
This conversion will be a no-op when using older
Sphinx versions.
Signed-off-by: Oliver Faso <erer1243@gmail.com>
Tested-by: Akira Yokosawa <akiyks@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20230910040811.53046-1-erer1243@gmail.com
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sun, 14 Jan 2024 13:53:13 +0000 (14:53 +0100)]
doc: create index entries for commands
Add the description of CLI commands to the generated index.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sun, 14 Jan 2024 13:54:03 +0000 (14:54 +0100)]
doc: add generated index to table of contents
Show the index in the navigation sidebar.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Mattijs Korpershoek [Wed, 3 Jan 2024 08:00:04 +0000 (09:00 +0100)]
doc: dfu: fix a handful of typos
Reword some sentences, add missing periods and fix various typos in the
dfu documentation.
This was originally contributed on [1]
[1] https://github.com/Maalobs/u-boot/commit/
9a21ed8ba722d904b68945f40ca6697b4b1cc4d4
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Venkatesh Yadav Abbarapu [Wed, 17 Jan 2024 03:20:14 +0000 (08:50 +0530)]
configs: zynqmp_kria: Enable CONFIG_OF_BOARD_SETUP
Enable CONFIG_OF_BOARD_SETUP, so we could use ft_board_setup()
to enable the kaslr-seed and pass to kernel.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240117032014.1014084-3-venkatesh.abbarapu@amd.com
Venkatesh Yadav Abbarapu [Wed, 17 Jan 2024 03:20:13 +0000 (08:50 +0530)]
xilinx: board: Update the kaslr-seed property
Create a ft_board_setup() api that gets called as part
of bootm/booti before jumping to kernel. In this
ft_board_setup() callback that will inspect the DTB
and insert the device tree blob with the "kaslr-seed" property.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240117032014.1014084-2-venkatesh.abbarapu@amd.com
Rasmus Villemoes [Wed, 3 Jan 2024 10:47:06 +0000 (11:47 +0100)]
cmd/command.c: relax length check in cmd_get_data_size()
Just check that the length is at least 2. This allows passing strings
like ".b", which can be convenient when constructing
tests (i.e. parametrizing the suffix used).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Wed, 3 Jan 2024 10:47:05 +0000 (11:47 +0100)]
cmd/command.c: constify "arg" argument of cmd_get_data_size()
This function obviously does not and must not modify "arg". Change the
prototype to allow passing an argument of type "const char*" without
requiring a cast.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Wed, 3 Jan 2024 10:47:04 +0000 (11:47 +0100)]
doc/usage/cmd/cp.rst: document that overlapping regions are supported
Now that the cp command is changed to use memmove() internally, update
the documentation to explicitly state that overlapping regions are
allowed.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Rasmus Villemoes [Wed, 3 Jan 2024 10:47:03 +0000 (11:47 +0100)]
cmd/mem.c: use memmove in do_mem_cp()
There's no 'mv' shell command for handling overlapping src and dst
regions, and there's no point introducing one, when we can just make
the existing 'cp' command DTRT in all cases. memmove() should at most
be a few instructions more then memcpy() (to detect the appropriate
direction to do the copy), which is of course completely in the noise
with all the string processing that a shell command does.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Love Kumar [Wed, 3 Jan 2024 10:29:42 +0000 (15:59 +0530)]
test/py: memtest: Add tests for mtest command
Add the following memory tests:
memtest_negative - To test mtest command by providing incorrect inputs
memtest_ddr - To test memory write-read-comparision for DDR memory
Signed-off-by: Love Kumar <love.kumar@amd.com>
Jim Liu [Wed, 3 Jan 2024 07:29:33 +0000 (15:29 +0800)]
reset: npcm: Add support for Nuvoton NPCM BMC family
Add reset controller driver for Nuvoton BMCs.
The npcm reset driver not only supports reset each module reset
but setting initial value of reset Control Registers.
And The driver support each module reset.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Love Kumar [Tue, 2 Jan 2024 06:47:07 +0000 (12:17 +0530)]
test/py: i2c: Add tests for i2c command
Add below test cases for i2c commands:
i2c_bus - To show i2c bus info,
i2c_dev - To set or show the current bus,
i2c_probe - To probe the i2c device,
i2c_eeprom - To test i2c eeprom device,
i2c_probe_all_buses - To list down all the buses and probes it
Signed-off-by: Love Kumar <love.kumar@amd.com>
Love Kumar [Tue, 2 Jan 2024 06:44:35 +0000 (12:14 +0530)]
test/py: mii: Add tests for mii command
Add below test cases for mii commands:
mii_info -To display MII PHY info
mii_list - To list MII devices
mii_set_device - To set MII device
mii_read - To reads register from MII PHY address
mii_dump - To display data from MII PHY address
Signed-off-by: Love Kumar <love.kumar@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
TracyMg_Li [Mon, 25 Dec 2023 03:21:34 +0000 (11:21 +0800)]
ARM add initial support for the Phytium Pe2201 Board.
Add pe2201 platform code and the device tree of pe2201 platform board.
The initial support comprises the UART and PCIe.
Signed-off-by: TracyMg_Li <TracyMg_Li@outlook.com>
Changes since v1:
fix space corrupt.
Changes since v2:
switch to bootstd and text environment.
Changes since v3:
add environment variables.
Heinrich Schuchardt [Sat, 23 Dec 2023 01:17:33 +0000 (02:17 +0100)]
lib: smbios: remove redundant next_header()
next_header() and get_next_header() only differ in how the const attribute
is used. One function taking a const parameter and returning a non-const is
good enough.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Heinrich Schuchardt [Sat, 23 Dec 2023 01:03:34 +0000 (02:03 +0100)]
smbios: copy QEMU tables
QEMU provides SMBIOS tables with detailed information. We should not try to
replicate them in U-Boot.
If we want to inform about U-Boot, we can add a Firmware Inventory
Information (type 45) table in future.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Neha Malcom Francis [Wed, 20 Dec 2023 11:34:33 +0000 (17:04 +0530)]
arm: dts: k3-j721e-binman: Add support for HS-SE 2.0
Add support for J721E HS-SE 2.0 device. Make use of the existing
templates and override the phandles for sysfw.itb so that builds do not
fail.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Wadim Egorov [Wed, 20 Dec 2023 09:18:11 +0000 (10:18 +0100)]
doc: board: phytec: Add phyCORE-AM62x
Add documentation for PHYTEC phyCORE-AM62x SoM.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Wadim Egorov [Wed, 20 Dec 2023 09:18:10 +0000 (10:18 +0100)]
board: phytec: am62x: Add PHYTEC phyCORE-AM62x SoM
Add basic support for PHYTEC phyCORE-AM62x SoM.
Supported features:
- 2GB DDR4 RAM
- eMMC Flash
- OSPI NOR Flash
- external uSD
- Ethernet
- debug UART
Product page SoM: https://www.phytec.com/product/phycore-am62x
Device trees were taken from Linux v6.7-rc3.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Love Kumar [Tue, 19 Dec 2023 12:20:51 +0000 (17:50 +0530)]
test/py: mdio: Add tests for mdio command
Add below test cases for mdio commands:
mdio_list - To list MDIO buses
mdio_read - To read PHY's register at <devad>.<reg>
mdio_write - To write PHY's register at <devad>.<reg>
Signed-off-by: Love Kumar <love.kumar@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Love Kumar [Tue, 21 Nov 2023 13:02:47 +0000 (18:32 +0530)]
test/py: net: Add dhcp abort test
Abort the dhcp request in the middle by pressing ctrl + c on u-boot
prompt and validate the abort status.
Signed-off-by: Love Kumar <love.kumar@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 16 Jan 2024 14:51:16 +0000 (09:51 -0500)]
Merge tag 'qcom-2024.04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-snapdragon
Qualcomm architecture changes:
* Move clock and pinctrl drivers out of mach-snapdragon
* Various clock driver improvements
* Convert PMIC power/reset key driver to use the button API
* Preparetory work for migrating to upstream DT
Tom Rini [Tue, 16 Jan 2024 14:49:48 +0000 (09:49 -0500)]
Merge tag 'u-boot-imx-
20240115' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Caleb Connolly [Mon, 15 Jan 2024 18:03:17 +0000 (18:03 +0000)]
sandbox_flattree: enable button support
sandbox_flattree enables QCOM_PMIC_GPIO which now depends on BUTTON. As
a result the button tests now get run, but fail because the ADC and GPIO
button drivers aren't enabled.
Enable them to run the tests for sandbox_flattree.
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Mon, 8 Jan 2024 15:30:51 +0000 (15:30 +0000)]
test: spmi: fix tests
With the recent changes to the Qualcomm PMIC GPIO driver the sandbox
tests for it no longer pass, update the DTS and tests to work with the
changes.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 5 Dec 2023 13:46:54 +0000 (13:46 +0000)]
pmic: qcom: dont use dev_read_addr to get USID
Linux DTs stuff a value indicating if the USID is a USID or a GSID in the
reg property, the Linux SPMI driver then reads the two address cells
separately. U-boot's dev_read_addr() doesn't know how to handle this, so
use ofnode_read_u32_index() to get just the USID.
The Qcom pmic driver doesn't have support for GSID handling, so just
ignore the second value for now.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 5 Dec 2023 13:46:53 +0000 (13:46 +0000)]
spmi: msm: fix register range names
The core and chnl register ranges were swapped on SDM845. Fix it, and
fetch the register ranges by name instead of by index.
Drop the cosmetic "version" variable and clean up the debug logging.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 5 Dec 2023 13:46:52 +0000 (13:46 +0000)]
gpio: qcom_pmic: drop gpio-count property
This property is not part of the dt bindings and all boards use the new
gpio-ranges property instead. Drop support for this.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 5 Dec 2023 13:46:51 +0000 (13:46 +0000)]
dts: qcom: adjust pmic gpio to use upstream bindings
Use the upstream gpio-ranges property instead of gpio-count, and drop
the bank-name property for Qualcomm boards.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 5 Dec 2023 13:46:50 +0000 (13:46 +0000)]
gpio: qcom_pmic: support upstream DT
Upstream uses the gpio-ranges property to define the number of GPIOs,
support for parsing this when gpio-count is unspecified
Additionally, drop the bank-name property as it isn't used in upstream,
and we can just hardcode the bank name instead.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 5 Dec 2023 13:46:49 +0000 (13:46 +0000)]
gpio: qcom_pmic: drop pon GPIO driver
Remove the (now unused) GPIO driver for the power and resin buttons on
the PMIC.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 5 Dec 2023 13:46:48 +0000 (13:46 +0000)]
mach-snapdragon: switch to PMIC button driver
The PMIC button driver is a much better representation of the hardware
here, adjust the boards to use upstream DT and the PMIC button driver
instead of exposing the buttons as GPIOs and relying on the GPIO-button
driver.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 5 Dec 2023 13:46:47 +0000 (13:46 +0000)]
button: qcom-pmic: introduce Qualcomm PMIC button driver
Qualcomm PMICs include a "pon" function which handles two buttons, the
power button and "resin" button (usually volume down). Introduce a new
driver following upstream Linux DT to enable these and map them to Enter
and Down respectively to enable use in boot menus.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 5 Dec 2023 13:46:46 +0000 (13:46 +0000)]
gpio: qcom_pmic: fix silent dev_read_addr downcast
priv->pid is uint32_t, but dev_read_addr() returns a uint64_t on arm64,
with the upper bits being used for error codes. Do error checking before
downcasting to u32 to prevent errors being silently ignored.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 14 Nov 2023 12:51:12 +0000 (12:51 +0000)]
serial: msm-geni: handle devm_clk_get() errors
devm_clk_get() returns an ERR_PTR on failure, not null. Fix the check to
avoid the board crashing when the clock isn't available.
Additionally, add the missing error handling for this function.
Fixes: 324df15a292e ("serial: qcom: add support for GENI serial driver")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 14 Nov 2023 12:51:11 +0000 (12:51 +0000)]
serial: msm-geni: don't rely on parent misc device
commit
1b15483deb3f ("misc: add Qualcomm GENI SE QUP device driver")
introduced support for platform-specific oversampling values, necessary
to configure the UART clocks on all platforms at runtime. However it
relies in probing a parent device. Despite the DM_FLAG_PRE_RELOC flag,
this is not done consistently during boot.
Instead, take another approach by relying on ofnode_ helpers to read the
serial engine base address and do the read directly. This fixes early
UART on boards with a non-default oversampling rate.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 14 Nov 2023 12:55:43 +0000 (12:55 +0000)]
msm_gpio: use unsigned int
Replaces the uses of "unsigned" with "unsigned int".
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 14 Nov 2023 12:55:42 +0000 (12:55 +0000)]
pinctrl: qcom: make compatible with linux DTs
The pinctrl and GPIO drivers are currently heavily incompatible with
upstream. Most Qualcomm pinctrl blocks feature "tiles" of pins, each at
it's own address. Introduce support for these by allowing the soc driver
to specify per-pin register offsets similarly to the Linux driver.
Adjust the GPIO driver to handle these too, and finally enable support
for all pins with the same numbering as used in Linux.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 14 Nov 2023 12:55:41 +0000 (12:55 +0000)]
pinctrl: qcom: move ipq4019 driver from mach-ipq40xx
Drop the duplicated pinctrl-snapdragon driver from mach-ipq40xx and add
it to drivers/pinctrl/qcom.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 14 Nov 2023 12:55:40 +0000 (12:55 +0000)]
pinctrl: qcom: move out of mach-snapdragon
Move the Qualcomm pinctrl drivers out of mach-snapdragon and over to the
rest of the pinctrl drivers, adjust the drivers so that support for each
platform can be enabled/disabled individually and introduce platform
specific configuration options.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 7 Nov 2023 12:41:05 +0000 (12:41 +0000)]
clk/qcom: fix rcg divider value
The RCG divider field takes a value of (2*h - 1) where h is the divisor.
This allows fractional dividers to be supported by calculating them at
compile time using a macro.
However, the clk_rcg_set_rate_mnd() function was also performing the
calculation. Clean this all up and consistently use the F() macro to
calculate these at compile time and properly support fractional divisors.
Additionally, improve clk_bcr_update() to timeout with a warning rather
than hanging the board, and make the freq_tbl struct and helpers common
so that they can be reused by future platforms.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 7 Nov 2023 12:41:04 +0000 (12:41 +0000)]
clk/qcom: add mnd_width to clk_rcg_set_rate_mnd()
This property is needed on some platforms to ensure that only the
relevant bits are set in the M/N/D registers.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 7 Nov 2023 12:41:03 +0000 (12:41 +0000)]
clk/qcom: use function pointers for enable and set_rate
Currently, it isn't possible to build clock drivers for more than one
platform due to how the msm_enable() and msm_set_rate() callbacks are
implemented.
Extend qcom_clk_data to include function pointers for these and convert
all platforms to use them.
Previously, clock drivers relied on include/configs/<board.h> to include the
board specific sysmap header, however as most of the header contents are clock
driver related, import the contents directly into each clock driver and
remove the header. The only exception here is the dragonboard820c board file
which includes some pinctrl macros, those are also inlined.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
[caleb: remove additional sysmap-sdm845.h mention]
Caleb Connolly [Tue, 7 Nov 2023 12:41:02 +0000 (12:41 +0000)]
clk/qcom: sdm845: add register map for simple gate clocks
Many gate clocks can be enabled with a single register write, add support
for defining these simple gate clocks and add the ones found on SDM845.
While we're here, inline clk_init_uart() into msm_set_rate().
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Konrad Dybcio [Tue, 7 Nov 2023 12:41:01 +0000 (12:41 +0000)]
clk/qcom: handle resets and clocks in one device
Qualcomm's clock controller blocks actually do much more than it
says on the tin.. They provide clocks, resets and power domains.
Currently, U-Boot requires one to spawn 2 separate devices for
controlling clocks and resets, both spanning the same register space.
Refactor the code to make it work with just a single DT node, making
it compatible with upstream Linux bindings and dropping the dedicated
reset driver in favour of including it in the clock driver.
Heavily inspired by Renesas code for a similar hw block.
[caleb: moved drivers to clk/qcom, added reset driver and adjusted bind
logic. Imported qcom,gcc-ipq4019.h from Linux]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 7 Nov 2023 12:41:00 +0000 (12:41 +0000)]
clk/qcom: move ipq4019 driver from mach-ipq40xx
This driver is just a stub, but it's necessary to support the upcoming
reset driver changes.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Caleb Connolly [Tue, 7 Nov 2023 12:40:59 +0000 (12:40 +0000)]
clk/qcom: move from mach-snapdragon
Clock drivers don't belong here, move them to the right place and
declutter mach-snapdragon a bit.
To de-couple these drivers from specific "target" platforms, add
additional config options to enable each clock driver gated behind a
common CLK_QCOM option and enable them by default for the respective
targets. This will make future work easier as we move towards a generic
Qualcomm target.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Tom Rini [Mon, 15 Jan 2024 14:29:57 +0000 (09:29 -0500)]
Merge tag 'u-boot-nand-
20240115' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
Pull request for u-boot-nand-
20240115
The first patch is by Heinrich Schuchardt and fixes an integer overflow
The following two patches are by Dario Binacchi and add arguments check
to the nand_mtd_to_devnum() and nand_register() functions.
The remaining patches are by Roger Quadros and include various fixes for
the OMAP platform.
Anatolij Gustschin [Mon, 15 Jan 2024 13:51:30 +0000 (14:51 +0100)]
arm: xea: Add support for boot image source descriptor in SPL
We load two boot image source descriptor structures from last
two sectors in the SPI NOR flash and determine the boot source
for loading the kernel/DTB images, then adjust the boot order for
loading image from eMMC boot0 or boot1 partition.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Mon, 15 Jan 2024 13:51:29 +0000 (14:51 +0100)]
arm: config: Enable CRC8 support in SPL on imx287 XEA board
The boot0/1 feature uses simple CRC8 to check (in SPL) if
SPI-NOR content is not corrupted, hence the need to enable
it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Mon, 15 Jan 2024 13:51:28 +0000 (14:51 +0100)]
arm: xea: Move XEA's environment variables from xea.h to xea.env
The default set of environment variables from CFG_EXTRA_ENV_SETTINGS
has been moved to a separate file - board/liebherr/xea/xea.env
Adjustments done:
- fitImage support
- SPI-NOR layout re-organization
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Yannic Moog [Mon, 15 Jan 2024 09:31:41 +0000 (10:31 +0100)]
board: phytec: fix link error when disabling PHYTEC_SOM_DETECTION
Commit
aa7858fe5e2e ("board: phytec: som_detection: move definitions to
source file") moved function definitions from header to source file.
Makefile however was not updated to unconditionally (from
[..]_SOM_DETECTION) build the imx8 and phytec som detection units.
Also remove unused includes that cause build failures on arm 32bit
boards. SoM detection shall support 32bit boards as well, but arch
specific code should not be included in the generic module.
Fixes: aa7858fe5e2e ("board: phytec: som_detection: move definitions to source file")
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Roger Quadros [Thu, 11 Jan 2024 13:19:20 +0000 (15:19 +0200)]
arm: mach-k3: am642: Define NAND boot device
AM642 SoC supports booting from GPMC NAND device.
Define boot device for it.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://www.mail-archive.com/u-boot@lists.denx.de/msg499180.html
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>