From 198fee844b0147feeb016aedc44b58069eb5d77e Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Fri, 17 May 2019 16:58:51 +0200 Subject: [PATCH] ARM: imx: dh-imx6: Convert SD/MMC support to DM Enable DM block and DM MMC support on DHCOM iMX6 PDK2. Convert board code to match the DM support. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: Ludwig Zenz Cc: Stefano Babic --- board/dhelectronics/dh_imx6/dh_imx6.c | 59 +-------------------------- configs/dh_imx6_defconfig | 1 + 2 files changed, 3 insertions(+), 57 deletions(-) diff --git a/board/dhelectronics/dh_imx6/dh_imx6.c b/board/dhelectronics/dh_imx6/dh_imx6.c index 44f4ef8130..193bb0eade 100644 --- a/board/dhelectronics/dh_imx6/dh_imx6.c +++ b/board/dhelectronics/dh_imx6/dh_imx6.c @@ -6,6 +6,8 @@ */ #include +#include +#include #include #include #include @@ -189,63 +191,6 @@ int board_eth_init(bd_t *bis) } #endif -#ifdef CONFIG_FSL_ESDHC - -#define USDHC2_CD_GPIO IMX_GPIO_NR(6, 16) -#define USDHC3_CD_GPIO IMX_GPIO_NR(7, 8) - -static struct fsl_esdhc_cfg usdhc_cfg[3] = { - { USDHC2_BASE_ADDR }, - { USDHC3_BASE_ADDR }, - { USDHC4_BASE_ADDR }, -}; - -int board_mmc_getcd(struct mmc *mmc) -{ - struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; - - switch (cfg->esdhc_base) { - case USDHC2_BASE_ADDR: - return gpio_get_value(USDHC2_CD_GPIO); - case USDHC3_BASE_ADDR: - return !gpio_get_value(USDHC3_CD_GPIO); - case USDHC4_BASE_ADDR: - return 1; /* eMMC/uSDHC4 is always present */ - } - - return 0; -} - -int board_mmc_init(bd_t *bis) -{ - int i, ret; - - /* - * According to the board_mmc_init() the following map is done: - * (U-Boot device node) (Physical Port) - * mmc0 SD interface - * mmc1 micro SD - * mmc2 eMMC - */ - gpio_request(USDHC2_CD_GPIO, "SD2-CD"); - gpio_request(USDHC3_CD_GPIO, "SD3-CD"); - gpio_direction_input(USDHC2_CD_GPIO); - gpio_direction_input(USDHC3_CD_GPIO); - - usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); - usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); - usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); - - for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { - ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); - if (ret) - return ret; - } - - return 0; -} -#endif - #ifdef CONFIG_USB_EHCI_MX6 static void setup_usb(void) { diff --git a/configs/dh_imx6_defconfig b/configs/dh_imx6_defconfig index 2443156b87..37c2f01485 100644 --- a/configs/dh_imx6_defconfig +++ b/configs/dh_imx6_defconfig @@ -11,6 +11,7 @@ CONFIG_NR_DRAM_BANKS=1 CONFIG_SPL=y CONFIG_SYS_BOOTCOUNT_ADDR=0x00900000 CONFIG_DM_GPIO=y +CONFIG_DM_MMC=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y CONFIG_DISTRO_DEFAULTS=y -- 2.39.5