Harald Seiler [Thu, 23 Apr 2020 11:07:53 +0000 (13:07 +0200)]
imx: spl: Fix use of removed SPL_FAT_SUPPORT config
CONFIG_SPL_FAT_SUPPORT was removed in commit 0c3a9ed409a5
("spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT").
Fixup a leftover use of the symbol.
Fixes: 9d86dbd9cf9d ("imx: spl: implement spl_boot_mode for i.MX7/8/8M") Signed-off-by: Harald Seiler <hws@denx.de>
Harald Seiler [Thu, 23 Apr 2020 11:07:52 +0000 (13:07 +0200)]
imx: spl: Remove ifdefs in spl_mmc_boot_mode()
It is hard to read code which contains nested ifdef blocks. Replace
them with normal if-blocks and the IS_ENABLED() macro. This is not only
more readable but also helps as both arms are validated by the compiler
in all cases.
Harald Seiler [Thu, 23 Apr 2020 11:07:50 +0000 (13:07 +0200)]
Revert "imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon mode"
The CONFIG_SPL_FORCE_MMC_BOOT config flag is not needed as its behavior
is the correct one in all cases; using spl_boot_device() instead of the
boot_device parameter will lead to inconsistency issues, for example,
when a board_boot_order() is defined. In fact, this is the reason the
parameter was introduced in the first place, in commit 2b1cdafa9fdd
("common: Pass the boot device into spl_boot_mode()").
imx: spl: return boot mode for asked MMC device in spl_mmc_boot_mode()
Boards may extend or re-define the boot list in their board_boot_order()
function by modifying spl_boot_list. E.g. a board might boot SPL from a
slow SPI NOR flash and then load the U-Boot from an eMMC or SD-card.
Or it might use additional MMC boot device in spl_boot_list for cases
when the image in SPI NOR flash is not found, so it could fall back to
eMMC, SD-card or another boot device.
Getting the MMC boot mode in spl_mmc will fail when we are trying to
boot from an MMC device in the spl_boot_list and the original board
boot mode (as returned by spl_boot_device()) is not an MMC boot mode.
Fix it by checking the asked MMC boot device from the spl_mmc_boot_mode()
argument.
Marek Vasut [Wed, 29 Apr 2020 13:04:27 +0000 (15:04 +0200)]
ARM: imx8m: Fix reset in SPL on Toradex iMX8MM Verdin
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Flavio Suligoi <f.suligoi@asem.it> Cc: Harald Seiler <hws@denx.de> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marek Vasut [Wed, 29 Apr 2020 13:04:26 +0000 (15:04 +0200)]
ARM: imx8m: Fix reset in SPL on NXP iMX8MP EVK
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Flavio Suligoi <f.suligoi@asem.it> Cc: Harald Seiler <hws@denx.de> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Wed, 29 Apr 2020 13:04:25 +0000 (15:04 +0200)]
ARM: imx8m: Fix reset in SPL on NXP iMX8MN EVK
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Flavio Suligoi <f.suligoi@asem.it> Cc: Harald Seiler <hws@denx.de> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Wed, 29 Apr 2020 13:04:24 +0000 (15:04 +0200)]
ARM: imx8m: Fix reset in SPL on NXP iMX8MM EVK
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Flavio Suligoi <f.suligoi@asem.it> Cc: Harald Seiler <hws@denx.de> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
Claudius Heine [Wed, 29 Apr 2020 13:04:23 +0000 (15:04 +0200)]
ARM: imx8m: Don't use the addr parameter of reset_cpu()
imx8m has the only implementation of reset_cpu() which does not ignore
the addr parameter and instead gives it some meaning as the base address
of watchdog registers. This breaks convention with the rest of U-Boot
where the parameter is ignored and callers are passing in 0.
Fixes: d2041725e84b ("imx8m: restrict reset_cpu") Co-developed-by: Harald Seiler <hws@denx.de> Signed-off-by: Harald Seiler <hws@denx.de> Signed-off-by: Claudius Heine <ch@denx.de>
Marek Vasut [Fri, 24 Apr 2020 19:37:33 +0000 (21:37 +0200)]
ARM: imx: imx8m: Do not warn about cpu-idle-states if missing
If the cpu-idle-states is missing from the DT in the first place, do
not fail on removing in. Just move on and do not even print an error,
since not being able to remove something which is not there in the
first place is not an error and surely does not justify failing to
boot.
Turn the surrounding prints into debugs to reduce the useless noise.
Adam Ford [Mon, 27 Apr 2020 12:11:19 +0000 (07:11 -0500)]
arm: dts: imx8mm: sync dts from Linux Kernel 5.6.7
This patch synchronizes the device tree with that from 5.6.7.
This also adds nodes for crypto and ddrc, which makes keeping
the device tree files from individual boards in sync with the
Linux kernel. This is helpful when boads reference those nodes.
Kuldeep Singh [Thu, 20 Feb 2020 17:27:54 +0000 (22:57 +0530)]
treewide: Remove unused FSL QSPI config options for IMX platforms
Some of these options are not used by the driver anymore and some of them
are obsolete as the information is gathered from the dt.
So, remove the unused config options now.
There is no watchdog driver for i.MX8 at the moment, nor code for
configuring the watchdog in SPL, so remove the CONFIG_SPL_WATCHDOG_SUPPORT
option for now.
define FEC_ENET_ENABLE_TXC_DELAY to enable the delay on TXC line on
the MAC. This has to be done in order to meet RGMII specs.
According to RGMII specs the clock should get delayed so the edges of
the clock are preferrably in the middle of the edges of data-lines so
they can be sampled properly.
Our PHY expects the MAC to delay TXC line, as it is also written
in the spec. This patch makes sure the TXC delay on the FEC is enabled
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch enables the possibility to set FEC_ENET_ENABLE_TXC_DELAY or
FEC_ENET_ENABLE_RXC_DELAY so one can via a define enable the RXC or TXC
delay in the MAC.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch adds skew register settings for KSZ9131. It checks first
which phy is on the board and then applies the correct skew settings.
Skew settings calculation for the KSZ9131:
The i.MX6 SoC has an output skew tolerance of -100ps to 900ps. All
PCB traces where routed exactly the same length so we can calculate
the skew settings without taking the length into consideration. The
traces are all length matched.
RXC skew (PHY to MAC):
- We use the 2ns DLL controlled delay on the PHY
- We do not use the skew registers
This results in the following values:
RXC
PHY fixed Delay 2000ps
PHY Added Delay 0ps
T_setup_R min 2.00ns
T_setup_R typ 2.00ns
T_setup_R max 2.00ns
T_hold_R min 1.60ns
T_hold_R typ 2.00ns
T_hold_R max 2.40ns
That means we are well within RGMII specs.
TXC skew (MAC to PHY):
- We use the 2ns DLL controlled delay on the PHY
- We then subtract ~0.6ns with TXD[0:3] and TXC clock pad skew
register in a resulting ~1.4ns delay.
This results in the following values under consideration of the
tolerances:
TXC min TXC typ TXC max
MAC min -100ps -100ps -100ps
MAC max 900ps 900ps 900ps
PHY fixed Delay 2000ps 2000ps 2000ps
PHY added Delay -340ps -600ps -859ps
T_setup_T min 1.56ns 1.30ns 1.04ns
T_setup_T typ 2.06ns 1.80ns 1.54ns
T_setup_T max 2.56ns 2.30ns 2.04ns
T_hold_T min 1.04ns 1.30ns 1.56ns
T_hold_T typ 1.94ns 2.20ns 2.46ns
T_hold_T max 2.84ns 3.10ns 3.36ns
This shows that T_hold_T min and T_setup_T min times are out of spec
for RGMII timing. However the KSZ9131 has a minimal value for this time
of 0.8ns which is met under all circumstances.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
This patch determines which phy is placed on the board with the PHY ID
then it sets the same settings for KSZ9031 as before but for KSZ9131
it enables both RXC and TXC delay lines in the PHY.
This will compensate the missing delay from the MAC. Other skew
settings are not needed as the traces on board are routed exactly the
same length
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
verdin-imx8mm: Change board phy skew values for our ksz9031
This patches uses the existing functions for interacting with the
KSZ9031 and uses the values appropriate for our board.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Claudius Heine [Wed, 4 Mar 2020 14:23:12 +0000 (15:23 +0100)]
imx: imx8m: Don't use the addr parameter of reset_cpu
imx8m has the only implementation of `reset_cpu` which does not ignore
the addr parameter and instead gives it some meaning as the base address
of watchdog registers. This breaks convention with the rest of U-Boot
where the parameter is ignored and callers are passing in 0.
Fixes: d2041725e84b ("imx8m: restrict reset_cpu") Co-Authored-by: Harald Seiler <hws@denx.de> Signed-off-by: Claudius Heine <ch@denx.de> Signed-off-by: Harald Seiler <hws@denx.de> Reviewed-by: Marek Vasut <marex@denx.de>
Claudius Heine [Wed, 4 Mar 2020 14:23:11 +0000 (15:23 +0100)]
imx: imx8m*: Remove do_reset from board files
Use the `do_reset` implementation of `arch/arm/lib/reset.c` in SPL
instead. It is very close to what is done here, anyway, and plays
more nicely with the rest of U-Boot than adding a custom `do_reset`
implementation into board files.
`do_reset` from `arch/arm/lib/reset.c` calls `reset_cpu` with 0 as the
addr parameter while the boards are passing WDOG1_BASE_ADDR. This is
ok because the `reset_cpu` implementation uses WDOG1_BASE_ADDR by
default if 0 is passed in.
Co-Authored-by: Harald Seiler <hws@denx.de> Signed-off-by: Claudius Heine <ch@denx.de> Signed-off-by: Harald Seiler <hws@denx.de> Reviewed-by: Marek Vasut <marex@denx.de>
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.
The module also adds some commands:
- snvs_cfg: Configure the SNVS HP and LP registers
- snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
- tamper_pin_cfg: Change the configuration of the tamper pins
- snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
status bits
Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Thu, 14 Nov 2019 05:20:43 +0000 (21:20 -0800)]
imx8: Update SCFW API to version 1.5
Sync the latest SCFW API with below commit 6dcd0242ae7a53ac ("SCF-105: Revert accidental change") to add
interfaces for PM resource reset and read/write SNVS security
violation and tamper DGO registers.
Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Mon, 9 Dec 2019 08:47:18 +0000 (00:47 -0800)]
imx8m: Enable WDOG_B for timeout
When doing reset_cpu, in normal case the WDOG_B outputs immediately
after we clean WDA bit. But on mscale, the WDOG_B may be later than
internal reset, and cause PMIC not reset. As we enabled the SD3.0
support, the PMIC must be reset to reset SD card.
Change the reset_cpu to enable the WDOG_B for timeout as well, and set
WDOG timeout to 1s.
Reviewed-by: Fabio Estevam <festevam@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 24 Mar 2020 02:54:29 +0000 (19:54 -0700)]
imx8mm: clock: fix fracpll decode issue
The fracpll decoding is using the bit definitions for int pll. Most of
them are same, but the CLKE bit is different. Fix the wrong CLKE_MASK
for fracpll and correct all bit definitions in fracpll decoding.
Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Fri, 25 Oct 2019 08:28:48 +0000 (01:28 -0700)]
imx8mq: Enable eMMC HS400 and SD UHS mode on EVK
iMX8MQ EVK board has a eMMC5.0 chip and supports SD3.0, so enable the UHS
and HS400 configs to enhance the eMMC/SD access.
The change also needs to set usdhc clock to 400Mhz, and add the
off-on-delay-us to SD reset pin, otherwise some SD cards will
fail to select UHS mode in re-initialization.
Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 12 Dec 2018 10:47:58 +0000 (02:47 -0800)]
imx8mn: Update speed grade
imx8mn speed grade fuse uses new definitions as below. So have
to update get_cpu_speed_grade_hz function to match it.
SPEED_GRADE[5:4] SPEED_GRADE[3:0] MHz
xx 0000 2300
xx 0001 2200
xx 0010 2100
xx 0011 2000
xx 0100 1900
xx 0101 1800
xx 0110 1700
xx 0111 1600
xx 1000 1500
xx 1001 1400
xx 1010 1300
xx 1011 1200
xx 1100 1100
xx 1101 1000
xx 1110 900
xx 1111 800
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Ye Li [Wed, 17 Oct 2018 06:12:37 +0000 (23:12 -0700)]
imx8mm: Update CPU speed grading
According to iMX8MM datasheet (IMX8MMIEC_Rev_D and IMX8MMCEC_Rev_D),
the speed grading for imx8mm is 800Mhz, 1.2Ghz, 1.6Ghz and 1.8Ghz.
Update them to get_cpu_speed_grade_hz function.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Marek Vasut [Fri, 24 Apr 2020 19:37:26 +0000 (21:37 +0200)]
ARM: imx: imx8mm: Add missing clock entries for FEC clock
All the FEC ethernet clock entries for iMX8MM are missing, while they
are already present on iMX8MQ. Fill in the nodes on iMX8MM, as the FEC
ethernet gets bogus clock information otherwise which makes ethernet
inoperable.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
Simon Glass [Sun, 26 Apr 2020 15:12:58 +0000 (09:12 -0600)]
x86: Move coreboot-table detection into common code
To support detecting booting from coreboot, move the code which locates
the coreboot tables into a common place. Adjust the algorithm slightly to
use a word comparison instead of string, since it is faster.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the comments to 960KB] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 26 Apr 2020 15:12:56 +0000 (09:12 -0600)]
pci: Avoid auto-config when chain loading
When U-Boot is not the first-stage bootloader we don't want to
re-configure the PCI devices, since this has already been done. Add a
check to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 26 Apr 2020 15:12:55 +0000 (09:12 -0600)]
x86: cpu: Skip init code when chain loading
When U-Boot is not the first-stage bootloader the interrupt and cache init
must be skipped, as well as init for various peripherals. Update the code
to add checks for this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 26 Apr 2020 15:12:53 +0000 (09:12 -0600)]
x86: fsp: Allow skipping init code when chain loading
It is useful to be able to boot the same x86 image on a device with or
without a first-stage bootloader. For example, with chromebook_coral, it
is helpful for testing to be able to boot the same U-Boot (complete with
FSP) on bare metal and from coreboot. It allows checking of things like
CPU speed, comparing registers, ACPI tables and the like.
When U-Boot is not the first-stage bootloader much of this code is not
needed and can break booting. Add checks for this to the FSP code.
Rather than checking for the amount of available SDRAM, just use 1GB in
this situation, which should be safe. Using 2GB may run into a memory
hole on some SoCs.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 26 Apr 2020 15:19:51 +0000 (09:19 -0600)]
acpi: Put table-setup code in its own function
We always write three basic tables to ACPI at the start. Move this into
its own function, along with acpi_fill_header(), so we can write a test
for this code.
Simon Glass [Sun, 26 Apr 2020 15:19:50 +0000 (09:19 -0600)]
acpi: Move acpi_add_table() to generic code
Move this code to a generic location so that we can test it with sandbox.
This requires adding a few new fields to acpi_ctx, so drop the local
variables used in the original code.
Also use mapmem to avoid pointer-to-address casts which don't work on
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Sun, 26 Apr 2020 15:19:47 +0000 (09:19 -0600)]
acpi: Convert part of acpi_table to use acpi_ctx
The current code uses an address but a pointer would result in fewer
casts. Also it repeats the alignment code in a lot of places so this would
be better done in a helper function.
Update write_acpi_tables() to make use of the new acpi_ctx structure,
adding a few helpers to clean things up.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Simon Glass [Sun, 26 Apr 2020 15:19:45 +0000 (09:19 -0600)]
acpi: Add a binding for ACPI settings in the device tree
Devices need to report various identifiers in the ACPI tables. Rather than
hard-coding these in drivers it is typically better to put them in the
device tree.
* don't copy GUIDs for no reason
* shorten print format strings by using variable names
* don't use the run-time table to access exported functions
* check the result of malloc() (fixes Coverity CID 300331)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* Do not recreate a variable name that we already have as u16 string.
* Check the return value of malloc()
* EFI_NOT_FOUND cannot occur for a variable name returned by
GetNextVariableName(). Remove a print statement.
* Don't copy a GUID for no reason.
* Don't use the run-time service table to call exported functions.
* Don't pass NULL to show_efi_boot_opt_data() (fixes Coverity CID 300338).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now for MBR and GPT partitions the info field 'bootable' was set to 1
if either the partition was an EFI system partition or the bootable flag
was set.
Turn info field 'bootable' into a bit mask with separate bits for bootable
and EFI system partition.
This will allow us to identify the EFI system partition in the UEFI
sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If udisksctl is present
test/py/tests/test_efi_secboot/conftest.py
fails because the disk image is never mounted.
Normal users can only mount fuse file systems. Unfortunately fusefat is
still in an experimental state and seems not to work here correctly.
So as we have to be root or use the sudo command anyway delete all coding
referring to udisksctl.
--
We should not use mount point /mnt as this directory or one of its
sub-directories might already be in use as active mount points. Instead
create a new directory in the build root as mount point.
--
Remove debug print statements that have been commented out. print without
parentheses is anyway invalid in Python 3. And pytest anyway filters out
the output if there is no exception reported.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Probe the FMan MACs based on the device tree while
retaining the legacy code/functionality.
One notable change introduced here is that, for DM_ETH,
the name of the interfaces is corrected to the fmX-macY
format, that avoids the referral to the MAC block names
which were incorrect for FMan v3 devices (i.e. DTSEC,
TGEC) and had weird formatting (i.e. FM1@DTSEC6, FM1@TGEC1).
The legacy code is left unchanged in this respect.
projects / u-boot.git / log