Tejas Bhumkar [Thu, 4 Jan 2024 04:52:17 +0000 (10:22 +0530)]
xilinx: Enable the NFS command by default
Enabled the default utilization of the NFS command across all Xilinx
platforms to facilitate the booting of images through the network
using the NFS protocol.
Michal Simek [Tue, 19 Dec 2023 16:16:50 +0000 (17:16 +0100)]
arm64: zynqmp: Rename i2c?-gpio to i2c?-gpio-grp
Anything ending with gpio/gpios is taken as gpio phande/description which
is reported as the issue coming from gpio-consumer.yaml schema.
That's why rename the gpio suffix to gpio-grp to avoid name collision.
Michal Simek [Tue, 19 Dec 2023 16:16:47 +0000 (17:16 +0100)]
arm64: zynqmp: Move fixed clock to / for kv260
fixed clock nodes can't be on the bus because they are missing reg
property. That's why move them to root.
And because it is root it is good to have it as the first node in a file.
Michal Simek [Mon, 18 Dec 2023 13:41:39 +0000 (14:41 +0100)]
arm64: zynqmp: Generate dfu_alt_info based on multiboot register
Commit 2c8a09219cdb ("arm64: zynqmp: Add multiboot support for SPL/SPI
offset calculation") enabled u-boot.itb offset calculation based on
multiboot register. It is also good to reflect location of u-boot.itb image
for dfu_alt generation.
Michal Simek [Mon, 18 Dec 2023 13:08:36 +0000 (14:08 +0100)]
arm64: zynqmp: Fix i2c bus for kd240
i2c1 is having all chips on it that's why use it instead of 0.
You can see this error when you boot system.
eth0: ethernet@ff0c0000
Setting bus to 0
Failure changing bus number (-19)
Enable permission for node ID 33
Enable permission for node ID 47
Hit any key to stop autoboot: 0
Tom Rini [Mon, 8 Jan 2024 18:39:00 +0000 (13:39 -0500)]
Merge tag 'u-boot-imx-master-20240108' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
- Removed fdt_addr from verdin-imx8mm to fix booting via bootefi.
- Support Ethernet PHY autodection on Data Modul i.MX8M Mini/Plus eDM
SBC
- Add i.MX93 binman support
- Add support for imx93-var-som
Mathieu Othacehe [Fri, 29 Dec 2023 10:55:23 +0000 (11:55 +0100)]
Add imx93-var-som support
Add support for the Variscite VAR-SOM-IMX93 evaluation kit. The SoM
consists of an NXP iMX93 dual A55 CPU. The SoM is mounted on a Variscite
Symphony SBC.
fdt_addr variable is the location in flash of the device tree blob [1], it
does not exist for verdin-imx8mm.
Because of this the bootefi command fails unless the optional
`[fdt address]` parameter is passed on the command line,
bootefi.c:efi_install_fdt() assumes that `fdt_addr` is valid when
present.
Fix this removing fdt_addr from the U-Boot environment.
[1] doc/usage/environment.rst
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Marek Vasut [Mon, 1 Jan 2024 21:05:54 +0000 (22:05 +0100)]
ARM: imx: Auto-detect PHY on Data Modul i.MX8M Mini/Plus eDM SBC
Implement fdtdec_board_setup() auto-detection of ethernet PHY.
This uses properties of the hardware and pull resistor placement.
If GPIO1_16 RGMII_MDC is HIGH, then R530 (MX8MM eDM SBC) or
R390 (MX8MP eDM SBC) is populated. R530 or R390 is populated
only on boards with AR8031 PHY.
If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down is the
dominant pull resistor. This is the case on boards with BCM54213PE
PHY.
In case AR8031 PHY is populated, the PHY MDIO address is 0, in
case BCM54213PE PHY is populated, the PHY MDIO address is 1, the
fdtdec_board_setup() is used to patch the correct address into
the U-Boot control DT.
Enable broadcom PHY support to support both PHYs.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add fields for the location of ACPI tables to the global data.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We have two implementations of write_acpi_tables(). One for writing ACPI
tables based on ACPI_WRITER() entries another based on copying tables from
QEMU.
Create a symbol CONFIG_QFW_ACPI that signifies copying ACPI tables from
QEMU and use it consistently.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
acpi: support 64bit in acpi_find_table for DSDT and FACS
Use X_DSDT and X_FIRMWARE_CTRL if available.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Rebased on -next to use nomap: Signed-off-by: Simon Glass <sjg@chromium.org>
On non x86 platforms the hardware reduce flag must be set in the FADT
table. Write an error message if the flag is missing.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Rebased on -next to use nomap, add hyphens: Signed-off-by: Simon Glass <sjg@chromium.org>
If field X_FIRMWARE_CTRL is filled, field FIRMWARE must be ignored. If
field X_DSDT is filled, field DSDT must be ignored.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Rebased on -next to use nomap: Signed-off-by: Simon Glass <sjg@chromium.org>
Fields X_FIRMWAE_CTRL and X_DSDT must be 64bit wide. Convert pointers to
to uintptr_t to fill these.
If field X_FIRMWARE_CTRL is filled, field FIRMWARE must be ignored. If
field X_DSDT is filled, field DSDT must be ignored. We should not fill
unused fields.
See the field definitions in chapter "5.2.9 Fixed ACPI Description Table
(FADT)" of the ACPI Specification 6.5.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 4 Jan 2024 01:49:19 +0000 (18:49 -0700)]
fdt: Allow the devicetree to come from a bloblist
Standard passage provides for a bloblist to be passed from one firmware
phase to the next. That can be used to pass the devicetree along as well.
Add an option to support this.
Tests for this will be added as part of the Universal Payload work.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Sun, 31 Dec 2023 15:25:55 +0000 (08:25 -0700)]
efi: Correct smbios-table installation
At present this code allocates memory when writing the tables and
then unnecessarily adds another memory map when installing it.
Adjust the code to allocate the tables using the normal U-Boot
mechanism. This avoids doing an EFI memory allocation early in
U-Boot, which may use memory that would be overwritten by a
'load' command, for example.
Simon Glass [Sun, 31 Dec 2023 15:25:54 +0000 (08:25 -0700)]
acpi: Write pointers to tables instead of addresses
Sandbox uses an API to map between addresses and pointers. This allows
it to have (emulated) memory at zero and avoid arch-specific addressing
details. It also allows memory-mapped peripherals to work.
As an example, on many machines sandbox maps address 100 to pointer
value 10000000.
However this is not correct for ACPI, if sandbox starts another program
(e.g EFI app) and passes it the tables. That app has no knowledge of
sandbox's address mapping. So to make this work we want to store 10000000 as the value in the table.
Add two new 'nomap' functions which clearly make this exeption to how
sandbox works.
This should allow EFI apps to access ACPI tables with sandbox, e.g. for
testing purposes.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Glass [Sun, 31 Dec 2023 15:25:49 +0000 (08:25 -0700)]
efi: Use the correct GUID for the SMBIOS table
EFI does not use the 'anchor string' to determine the SMBIOS table
version, instead preferring to have two separate GUIDs. Use the correct
one, depending on the table version.
Call unmap_system() to balance to the use of map_sysmem()
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Sun, 31 Dec 2023 15:25:47 +0000 (08:25 -0700)]
smbios: Use SMBIOS 3.0 to support an address above 4GB
When the SMBIOS table is written to an address above 4GB a 32-bit table
address is not large enough.
Use an SMBIOS3 table in that case.
Note that we cannot use efi_allocate_pages() since this function has
nothing to do with EFI. There is no equivalent function to allocate
memory below 4GB in U-Boot. One solution would be to create a separate
malloc() pool, or just always put the malloc() pool below 4GB.
- Use log_debug() for warning
- Rebase on Heinrich's smbios.h patch
- Set the checksum for SMBIOS3
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Sat, 6 Jan 2024 14:57:56 +0000 (09:57 -0500)]
Merge branch 'staging' of https://source.denx.de/u-boot/custodians/u-boot-tegra into next
Documentation updates for endeavoru, lg_x3, grouper and transformers,
addition of MIPI calibration clock name for T114 (inline with T124+),
conversion of TEGRA_SUPPORT_NON_SECURE into Kconfig and endeavoru
stability improvements.
Jan Kiszka [Sat, 6 Jan 2024 12:39:07 +0000 (13:39 +0100)]
arm: dts: iot2050: Fix by syncing from Linux
This restores support for IOT2050 by widely synchronizing its DT files
with the Linux kernel. We additionally need to add the alias restoration
that is still waiting for its upstream merge and the not-yet-upstreamed
bits needed for watchdog reboot detection.
Fixes: 4dbdc84754ea ("arm: dts: k3-am654: pull in dtb update from Linux") Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Rafał Miłecki [Wed, 13 Dec 2023 12:13:54 +0000 (13:13 +0100)]
fw_env: keep calling read() until whole flash block is read
It's totally valid for read() to provide less bytes than requested
maximum. It may happen if there is no more data available yet or source
pushes data in small chunks.
This actually happens when trying to read env data from NVMEM device.
Kernel may provide NVMEM content in page size parts (like 4096 B).
This fixes warnings like:
Warning on /sys/bus/nvmem/devices/u-boot-env0/nvmem: Attempted to read 16384 bytes but got 4096
Warning on /sys/bus/nvmem/devices/u-boot-env0/nvmem: Attempted to read 12288 bytes but got 4096
Warning on /sys/bus/nvmem/devices/u-boot-env0/nvmem: Attempted to read 8192 bytes but got 4096
Since the main loop in flash_read_buf() is used to read blocks this
patch adds a new nested one.
Rafał Miłecki [Wed, 13 Dec 2023 09:23:44 +0000 (10:23 +0100)]
fw_env: rename variables holding env data content
Rename "addr0" and "addr1" to "buf0" and "buf1" accordingly. Name "addr"
suggests that variable contains a numeric value being some kind of
address. Name "buf" is de facto a standard name for pointer to allocated
memory for reading data to.
While at it drop redundant checks for NULL before calling free().
Rafał Miłecki [Tue, 12 Dec 2023 17:33:27 +0000 (18:33 +0100)]
fw_env: fix reading NVMEM device's "compatible" value
Call to fread() was changed to check for return value. The problem is it
can't be checked for returning 1 (as it is) to determine success.
We call fread() with buffer size as "size" argument. Reading any
"compatible" value shorter than buffer size will result in returning 0
even on success.
Modify code to use fstat() to determine expected read length.
This fixes regression that broke using fw_env with NVMEM devices.
Unlike all other supported Tegra devices and most known Tegra devices, the
HTC One X has no hardware way to enter APX/RCM mode, which may lead to a
dangerous situation when, if BCT is set correctly and the bootloader is
faulty, the device will hang in a permanent brick state. Exiting from this
state can be done only by disassembling the device and shortening the
testpad to the ground.
To prevent this or to minimize the probability of such an accident, it was
proposed to add the RCM rebooting hook as early into SPL as possible since
SPL is much more robust and has minimal changes that can break bootflow.
gpio_early_init_uart() function was chosen as it is the earliest function
exposed for setup by the device. Hook performs a check for volume up button
state and triggers RCM if it is pressed.
Tom Rini [Thu, 4 Jan 2024 21:53:49 +0000 (16:53 -0500)]
Merge patch series "ATF and OP-TEE Firewalling for K3 devices."
Manorit Chawdhry <m-chawdhry@ti.com> says:
K3 devices have firewalls that are used to prevent illegal accesses to
memory regions that are deemed secure. The series prevents the illegal
accesses to ATF and OP-TEE regions that are present in different K3
devices.
AM62X, AM62AX and AM64X are currently in hold due to some firewall
configurations that our System Controller (TIFS) needs to handle.
The devices that are not configured with the firewalling nodes will not
be affected and can continue to work fine until the firewall nodes are
added so will be a non-blocking merge.
Test Logs: https://gist.github.com/manorit2001/4cead2fb3a19eb5d19005b3f54682627
CICD Run: https://github.com/u-boot/u-boot/pull/442
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com> Tested-by: Thomas Richard <thomas.richard@bootlin.com>
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Manorit Chawdhry [Fri, 29 Dec 2023 10:46:26 +0000 (16:16 +0530)]
binman: ti-secure: Add support for firewalling entities
We can now firewall entities while loading them through our secure
entity TIFS, the required information should be present in the
certificate that is being parsed by TIFS.
The following commit adds the support to enable the certificates to be
generated if the firewall configurations are present in the binman dtsi
nodes.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Manorit Chawdhry [Fri, 29 Dec 2023 10:46:25 +0000 (16:16 +0530)]
dtoc: Change dst to self in debug message
Fix the error message to not use dst and use self as it is copying the
properties to self.
While using templating if there are no subnodes defined, we end up in
this situation where "dst" isn't defined and it tries to print the error
message and fails.
'UnboundLocalError: local variable 'dst' referenced before assignment'
Fixes: 55e1278d5eca ("dtoc: Allow inserting a list of nodes into another") Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Nishanth Menon [Sat, 4 Nov 2023 07:21:48 +0000 (02:21 -0500)]
configs: j7200: Remove HBMC_AM654 config
Kernel commit 1b77265626a4 ("arm64: dts: ti: k3-j7200-mcu-wakeup: Add
HyperBus node") was merged to kernel without its dependent patch [1].
Similar fix is needed in U-Boot, and hbmc currently breaks boot. Till
this gets fixed in U-Boot, disable the config by default so that the
hbmc probe that happens in board/ti/j721e/evm.c will not take place
and lead to boot failure.
This is similar to the approach in commit 5b2671594b80 ("configs:
j721e: Remove HBMC_AM654 config"), introduced to j7200 evm platform.
Commit 19a91f2464a8 ("Create a new boot/ directory") moved the
android_ab.c code under boot/android_ab but did not update
the MAINTAINERS entry.
Update it so that the maintainer will get cc'ed again.
Fixes: 19a91f2464a8 ("Create a new boot/ directory") Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tom Rini [Wed, 3 Jan 2024 13:38:40 +0000 (08:38 -0500)]
Merge patch series "sync am65x device tree with Linux v6.7-rc1"
Bryan Brattlof <bb@ti.com> says:
Hello Again Everyone!
This series gets the am65x booting again along with syncing the device
tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64
files to make future syncs from Linux much easier. In the end the DTBs
should look a lot like what the DTBs look like for the am64x which
is fairly similar to the am65x.
Bryan Brattlof [Fri, 29 Dec 2023 17:47:23 +0000 (11:47 -0600)]
arm: dts: k3-am654: convert bootph-pre-ram to bootph-all
Many nodes are reused between WKUP SPL, MAIN SPL, and U-Boot. Using
bootph-pre-ram is causing these nodes to be present in SPL builds but
pruned away during the U-Boot build. Convert these nodes to bootph-all
so they will remain no matter which dtb build is happening.
Bryan Brattlof [Fri, 29 Dec 2023 17:47:09 +0000 (11:47 -0600)]
arm: dts: k3-am654: add needed regs to udmap nodes
Ethernet is one of a few IPs in U-Boot that depend on DMA to operate.
However there are a few missing registers ranges in the udmap nodes
need to properly setup DMA for the am65x.
A fix has been added to the Linux kernel[0] to add these ranges however
they have not made it to a Linux tag. To keep DMA operational until the
next DT sync from Linux, add these ranges to the *-u-boot.dtsi with a
note for our future selves.
Bryan Brattlof [Fri, 29 Dec 2023 17:47:06 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate timer
timer1 is really just the mcu_timer0 node redefined for the WKUP SPL.
Remove the timer1 and replace it with the mcu_timer0 from the Linux
device tree we imported into U-Boot.
projects / u-boot.git / log