Marek Vasut [Fri, 22 Apr 2022 08:57:53 +0000 (10:57 +0200)]
ARM: dts: imx: Use 100 kHz I2C2 on Data Modul i.MX8M Mini eDM SBC
The I2C2 has SMBus device SMSC USB2514Bi connected to it, the device is
capable of up to 100 kHz operation. Reduce the bus frequency to 100 kHz
to guarantee this I2C device can work correctly.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
RNG Hardware error is reported due to incorrect entropy delay
rng self test are run to determine the correct ent_dly.
test is executed with different voltage and temperature to identify the
worst case value for ent_dly. after adding a margin value(1000),
ent_dly should be at least 12000.
Robert Marko [Fri, 6 May 2022 18:01:39 +0000 (20:01 +0200)]
pinctrl: probe pinctrl drivers during post-bind
Currently, pinctrl drivers only get probed if pinconf is actually being
used, however on SoC-s like Armada 3720 pinctrl driver is a also the GPIO
driver.
So, if the pinctrl driver doesn't get probed GPIO-s won't get registered
and thus they cannot be used.
This is a problem on the Methode eDPU as it just uses SB pins as GPIO-s
and without them being registered networking won't work as it only has
one SFP slot and the TX disable GPIO is on the SB controller.
So, probe the pinctrl drivers using DM_FLAG_PROBE_AFTER_BIND like LED
uclass does.
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Robert Marko [Fri, 6 May 2022 11:54:43 +0000 (13:54 +0200)]
mvebu: uDPU: include fixed-phy support
uDPU relies on using fixed-phy for the SFP support, and since the
fixed-phy parsing was moved to the generic driver instead of mvneta
networking stopped working on uDPU with:
uDPU>> dhcp
dm_eth_phy_connect failed
This is due to the conversion commit not enabling fixed-phy support
in defconfig like it did for other boards.
Fixes: 77fcf3cf1251 ("net: mvneta: Convert to use PHY_FIXED for fixed-link") Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 6 May 2022 09:05:16 +0000 (11:05 +0200)]
serial: ns16550: Add support for SPL_DEBUG_UART_BASE
Use CONFIG_VAL(DEBUG_UART_BASE) instead of CONFIG_DEBUG_UART_BASE, so
proper config value (CONFIG_DEBUG_UART_BASE or CONFIG_SPL_DEBUG_UART_BASE)
is used based on building target.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 6 May 2022 09:05:14 +0000 (11:05 +0200)]
arm: mvebu: Move internal registers in arch_very_early_init() function
Moving of internal registers from INTREG_BASE_ADDR_REG to SOC_REGS_PHY_BASE
needs to be done very early, prior calling any function which may touch
internal registers, like debug_uart_init().
So do it earlier in arch_very_early_init() instead of arch_cpu_init().
Movement is done in proper U-Boot, not in SPL. SPL may return to bootrom
and bootrom requires internal registers at (old) expected location.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 6 May 2022 09:05:13 +0000 (11:05 +0200)]
arm: Add new config option ARCH_VERY_EARLY_INIT
When this option is set then ARM _main() function would call
arch_very_early_init() function at the beginning. It would be before
calling any other functions like debug_uart_init() and also before
initializing C runtime environment.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 3 May 2022 09:13:24 +0000 (11:13 +0200)]
cmd: mvebu: Hide bubt specific options when bubt is disabled
CONFIG_MVEBU_NAND_BOOT, CONFIG_MVEBU_SPI_BOOT, CONFIG_MVEBU_MMC_BOOT and
CONFIG_MVEBU_UBOOT_DFLT_NAME are unused when CONFIG_CMD_MVEBU_BUBT is not
enabled. So hide them.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Wed, 11 May 2022 17:27:44 +0000 (13:27 -0400)]
Merge branch '2022-05-11-Kconfig-cleanups-etc'
- Migrate CONFIG_MTD_CONCAT to Kconfig, use CONFIG_VAL/IS_ENABLED in
more places, rename SPL_LEGACY_IMAGE_SUPPORT to
SPL_LEGACY_IMAGE_FORMAT and update some related dependencies for TI
platforms.
Ovidiu Panait [Mon, 2 May 2022 15:34:56 +0000 (18:34 +0300)]
board_r: use IS_ENABLED(CONFIG_NEEDS_MANUAL_RELOC) in board_init_r()
Drop CONFIG_NEEDS_MANUAL_RELOC ifdefs in board_init_r() and use
IS_ENABLED() instead. Also, use the MANUAL_RELOC() macro to update the
initcall pointers.
common/console.c: use CONFIG_VAL() with PRE_CON_BUF_* variables
There is currently no support for PRE_CONSOLE_BUFFER in SPL, but if
and when that gets implemented, one would almost certainly want to use
a different address and/or size for the buffer (e.g., U-Boot proper
might specify an address in DRAM and a generous buffer, while SPL
would be much more constrained).
So a prerequisite for adding SPL_PRE_CONSOLE_BUFFER is to make the
code use SPL_-specific values. No functional change.
Andrew Davis [Wed, 4 May 2022 20:52:28 +0000 (15:52 -0500)]
boot: Kconfig: Enable FIT processing by default on TI secure devices
TI secure devices chain-of-trust depends on FIT image processing,
enable it by default on these devices. This also reduces the delta
between the secure and non-secure defconfig files.
Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Andrew Davis [Wed, 4 May 2022 20:52:27 +0000 (15:52 -0500)]
boot: Kconfig: Disable non-FIT loading for TI secure devices
Non-FIT image loading support should be disabled for TI secure
devices as the image handlers for those image types do not follow
our secure boot checks.
Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Andrew Davis [Wed, 4 May 2022 20:52:25 +0000 (15:52 -0500)]
spl: Rename Kconfig SPL_LEGACY_IMAGE_SUPPORT to SPL_LEGACY_IMAGE_FORMAT
This matches what this support is called in the non-SPL case. The postfix
_SUPPORT is redundant as enabling Kconfig options implies support.
With this we can use CONFIG_IS_ENABLED() as needed.
Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 10 May 2022 19:28:02 +0000 (15:28 -0400)]
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
Sean Anderson [Fri, 22 Apr 2022 20:11:37 +0000 (16:11 -0400)]
misc: Fix always compiling MISC even for SPL/TPL
We should only build support for misc if the appropriate SPL/TPL symbol
is defined. To ease the transition, make SPL/TPL_MISC default to MISC.
This is necessary because many drivers don't specify their dependencies
properly. These defaults can be removed once all drivers depend on the
appropriate config.
Fixes: aaba703fd0 ("spl: misc: Allow misc drivers in SPL and TPL") Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add VPL_MISC symbol, handle like SPL/TPL_MISC] Signed-off-by: Tom Rini <trini@konsulko.com>
configs: stm32f746-disco: use CONFIG_DEFAULT_DEVICE_TREE as fdtfile
As stm32f46-disco, stm32f769-disco and stm32746g-eval are very similar
except their respective device tree file. These 3 boards uses the same
TARGET_STM32F746_DISCO flag (so same include/configs/stm32f746-disco.h
and same board file board/st/stm32f746-disco/stm32f746-disco.c)
To be able to compile these 3 boards, replace the hard-coded device-tree
name in include/configs/stm32f746-disco.h by CONFIG_DEFAULT_DEVICE_TREE
which is set in each board defconfig file with the correct value.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
configs: stm32f746-disco: Concatenate spl and u-boot binaries
This allows to concatenate spl and u-boot binaries together.
Previously, both binaries has to be flashed separately at the correct
offset (spl at offset 0 and u-boot at offset 0x8000).
With this patch, only one binary is generated (u-boot-with-spl.bin)
and has to be copied in flash at offset 0 using openocd for example
or simply copied in exported mass storage.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On some STM32 SoC's package, GPIO bank may have hole in their GPIO bank
Example:
If GPIO bank have 16 GPIO pins [0-15].
In particular SoC's package case, some GPIO bank can have less GPIO pins:
- [0-10] => 11 pins;
- [2-7] => 6 pins.
Commit dbf928dd2634 ("gpio: stm32f7: Add gpio bank holes management")
proposed a first implementation by not counting GPIO "inside" hole. GPIO
are not displaying correctly using gpio or pinmux command when GPIO holes
are located at the beginning of GPIO bank.
To simplify, consider that all GPIO have 16 GPIO and use the gpio_ranges
struct to indicate if a GPIO is mapped or not. GPIO uclass offers several
GPIO functions ("input", "output", "unused", "unknown" and "func"), use
"unknown" GPIO function to indicate that a GPIO is not mapped.
stm32_offset_to_index() is no more needed and removed.
This must be reflected using the "gpio" command to indicate to user
that a particular GPIO is not mapped (marked as "unknown") as shown below:
Example for a 16 pins GPIO bank with the [2-7] mapping (only 6 pins
mapped):
GPIOI0 : unknown
GPIOI1 : unknown
GPIOI2 : analog
GPIOI3 : analog
GPIOI4 : alt function 0 push-pull pull-down
GPIOI5 : alt function 0 push-pull pull-down
GPIOI6 : alt function 0 push-pull pull-down
GPIOI7 : analog
GPIOI8 : unknown
GPIOI9 : unknown
GPIOI10 : unknown
GPIOI11 : unknown
GPIOI12 : unknown
GPIOI13 : unknown
GPIOI14 : unknown
GPIOI15 : unknown
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
ARM: stm32: Use CONFIG_TFTP_TSIZE on STMicroelectronics boards
Long TFTP transfers lead to a wall of # characters on UART, which in
the end may slow down the transfer itself. Use CONFIG_TFTP_TSIZE to
print progress in fewer # characters.
The Buck3 on DHCOR is used to supply IO voltage. It can output either 3V3
in the default DHCOR configuration, or 2V9 in case of AV96 DHCOR variant
which has extra Empirion DCDC converter in front of the 1V8 IO supply, or
outright 1V8 in case of 1V8 IO DHCOR without the Empirion DCDC converter.
The 2V9 mode in case of AV96 DHCOR variant is used to reduce unnecessarily
high input voltage to the Empirion DCDC converter, so move it into matching
DTSI to stop confusing users.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Sun, 1 May 2022 16:43:29 +0000 (18:43 +0200)]
ARM: stm32: Use CONFIG_TFTP_TSIZE on DHSOM
Long TFTP transfers lead to a wall of # characters on UART, which in
the end may slow down the transfer itself. Use CONFIG_TFTP_TSIZE to
print progress in fewer # characters.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Sun, 1 May 2022 16:43:28 +0000 (18:43 +0200)]
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
The DHCOM does ship with KS8851 with 1.5 kiB packet buffer. The DHSOM
may be extended with other MAC options connected to FMC2 bus, like the
DM9000, wih similar limitations. Use default CONFIG_TFTP_BLOCKSIZE of
1468 Bytes instead of 1536 Bytes, which always avoids overflowing the
packet buffers of such limited MACs, which leads to e.g. TFTP timeouts.
This also avoids receiving a short packet fragment at the end of each
TFTP block, which led to reduced performance.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Tue, 26 Apr 2022 14:38:05 +0000 (16:38 +0200)]
stm32mp: psci: Retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
The SoC seems to lose the values of MCUDIVR, PLL3CR, PLL4CR, RCC_MSSCKSELR
during suspend/resume cycle, cache them and reinstate their values on resume.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Tue, 26 Apr 2022 14:37:41 +0000 (16:37 +0200)]
ram: stm32mp1: Conditionally enable ASR
Enable DRAM ASR, auto self-refresh, conditionally, based on DT PWRCTL
register bits. While ASR does save considerable amount of power at
runtime automatically, it also causes LTDC underruns on large panels.
Let user select whether or not ASR is required or not, generally ASR
should be enabled on portable and battery operated devices.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Tue, 26 Apr 2022 13:38:05 +0000 (15:38 +0200)]
arm: dts: stm32mp15: alignment with v5.18
Device tree alignment with Linux kernel v5.18-rc2:
- ARM: dts: stm32: Add support for the emtrion emSBC-Argon
(only the pincontrol part)
- ARM: dts: stm32: Drop duplicate status okay from DHCOM gpioc node
- ARM: dts: stm32: add st,stm32-sdmmc2 compatible on stm32mp151
- ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
- ARM: dts: stm32: use exti 19 as main interrupt to support RTC wakeup on
stm32mp157
- ARM: dts: stm32: add DMA configuration to UART nodes on stm32mp151
- ARM: dts: stm32: keep uart4 behavior on *
- ARM: dts: stm32: Correct masks for GIC PPI interrupts on stm32mp15
Patrick Delaunay [Mon, 28 Mar 2022 17:25:32 +0000 (19:25 +0200)]
stm32mp: stm32prog: handle U-Boot script in flashlayout alternate
Update the stm32prog command to allow the reception of U-Boot script in
the FlashLayout alternate during the first USB enumeration.
This patch is aligned with the last TF-A behavior: the Flashlayout
is now loaded by U-Boot; it is no more present at STM32_DDR_BASE when
the stm32prog is launched after a serial boot, on UART or on USB.
The received script must be a U-Boot legacy image, no more need to add
a stm32image header.
Patrick Delaunay [Mon, 28 Mar 2022 17:25:31 +0000 (19:25 +0200)]
stm32mp: stm32prog: handle interruption during the first enumeration
When an interruption is received during the first USB enumeration
used to received the FlashLayout, with handle ctrl-c, the second
enumeration is not needed and the result for stm32prog_usb_loop
is false (reset is not needed).
This patch avoids the need of a second ctrl to interrupt the command
stm32prog.
Patrick Delaunay [Mon, 28 Mar 2022 17:25:30 +0000 (19:25 +0200)]
stm32mp: stm32prog: add support of UUID for FIP partition
Add support of UUID for FIP parttion, required by Firmware update
support in TF-A:
- UUID TYPE for FIP partition: 19d5df83-11b0-457b-be2c-7559c13142a5
- "fip-a" partition UUID: 4fd84c93-54ef-463f-a7ef-ae25ff887087
- "fip-b" partition UUID: 09c54952-d5bf-45af-acee-335303766fb3
This check is done with a new partition type "FIP" associated
at the FIP UUID.
The A/B partition UUID is detected by the partition name:
"fip-a", "fip-b".
Patrick Delaunay [Mon, 28 Mar 2022 17:25:27 +0000 (19:25 +0200)]
stm32mp: stm32prog: add CONFIG_CMD_STM32PROG_OTP
Add a configuration flag CONFIG_CMD_STM32PROG_OTP to enable the support of
OTP update in stm32prog command.
This new configuration allows to deactivate this feature for security reason
and it is a preliminary step for support of OPT update with the OP-TEE
provisioning TA.
atsha204 chip is predecessor of atsha204a chip. Current U-Boot driver
atsha204a-i2c.c can use both atsha204 and atsha204a chips because it does
not call specific functions to just one of these chips.
Pali Rohár [Mon, 9 May 2022 13:00:47 +0000 (15:00 +0200)]
Nokia RX-51: Enable CONFIG_SUPPORT_RAW_INITRD
This enable booting of Debian systems which use raw initrd image (instead
of uInitrd created by mkimage). This change increase size of u-boot.bin
binary by just 64 bytes.
Tom Rini [Sun, 8 May 2022 15:31:48 +0000 (11:31 -0400)]
Merge tag 'efi-2022-07-rc3-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc3-2
UEFI:
* Fix build errors due to
- using sed with non-standard extension for regular expression
- target architecture not recognized for CROSS_COMPILE=armv7a-*
- CONFIG_EVENT not selected
* add sha384/512 on certificate revocation
Others:
* factor out the user input handling in bootmenu command
efi_loader: add sha384/512 on certificate revocation
Currently we don't support sha384/512 for the X.509 certificate
in dbx. Moreover if we come across such a hash we skip the check
and approve the image, although the image might needs to be rejected.
Rework the code a bit and fix it by adding an array of structs with the
supported GUIDs, len and literal used in the U-Boot crypto APIs instead
of hardcoding the GUID types.
It's worth noting here that efi_hash_regions() can now be reused from
efi_signature_lookup_digest() and add sha348/512 support there as well
Mark Kettenis [Thu, 5 May 2022 14:42:23 +0000 (16:42 +0200)]
Makefile: Avoid non-portable GNU sed extension
Use [:space:] instead of \s and \S in regular expression that
determines the sandbox target architecture. Fixes the build
failure on OpenBSD introduced with commit 4e65ca00f3a3
("efi_loader: bootmgr: add booting from removable media").
Fixes: f7691a6d736b ("sandbox: allow cross-compiling sandbox") Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
John Keeping [Wed, 20 Apr 2022 10:31:11 +0000 (11:31 +0100)]
fdt: don't set linux,phandle
This has been deprecated for over 10 years and everything now uses the
plain "phandle" property in preference. There's no need to set
linux,phandle when creating phandles for nodes that do not have one.
dtc changed the default to creating just phandle in version 1.4.5
released in September 2017 with the justification that the new style had
already been supported for 7 years by that point (see dtc commit 0016f8c
("dtc: change default phandles to ePAPR style instead of both")).
Philippe Reynes [Fri, 22 Apr 2022 15:46:49 +0000 (17:46 +0200)]
cmd: gpt: add subcommand repair
Adds a sub-command repair to the command gpt
that allow to repair a corrupted gpt table. If
the both gpt table (primary and backup) are
valid, then the command does nothing.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
projects / u-boot.git / log