pinctrl: imx: Define imx6_pinctrl_soc_info in .data section
This commit is necessary to be able to re-use the pinctrl code in early
SPL to properly configure pins.
The problem is that those "static" structures (without explicit
initialization) are placed in the SDRAM area, which corresponds to
u-boot proper (not even SPL).
Hence, when one wants to configure pins before relocation via DTS/DM,
the board hangs (imx6q SoC powered one) as only OCRAM area is available
(0x009xxxxx).
This commit prevents from this issue by moving the imx6_pinctrl_soc_info
structure to data section (from BSS).
Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Marek Vasut [Fri, 17 May 2019 20:25:24 +0000 (22:25 +0200)]
ARM: imx: vining2000: Convert MMC and block to DM
Enable DM block and DM MMC support on iMX6SX VINING|2000 .
Convert board code to match the DM support. This disables
USB mass storage support due to missing DM USB, however
that will be re-enabled in subsequent patch.
Marek Vasut [Sun, 9 Jun 2019 01:50:55 +0000 (03:50 +0200)]
pci: imx: Add DM and DT support
Add DM support and support for probing the iMX PCI driver from DT.
The legacy non-DM support is retained, however shall be removed once
DM PCI is the only option remaining.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Marek Vasut [Sun, 9 Jun 2019 01:50:54 +0000 (03:50 +0200)]
pci: imx: Pass driver private data around
Pass the driver private data around the driver as much as possible, instead
of having it as a static global variable. This is done in preparation for
the DM conversion, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The driver limits the config space base to 32bit, however it can be
64bit on 64bit iMX hardware too. Remove that limitation. This patch
has no impact on the iMX6, which is the only SoC currently supported
by this driver.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Marek Vasut [Sun, 9 Jun 2019 01:50:51 +0000 (03:50 +0200)]
ARM: imx: Call imx_pcie_remove() only for non-DM PCI driver
The DM iMX PCI driver has DM_FLAG_OS_PREPARE set and will call
imx_pcie_remove() from the .remove callback. Do not call it from
the architecture code again.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fabio Estevam [Tue, 21 May 2019 13:37:52 +0000 (10:37 -0300)]
mx6sabresd: Remove CONFIG_SPL_DM to decrease the SPL size
Currently the mx6qsabresd board does not boot:
U-Boot SPL 2019.07-rc2 (May 16 2019 - 14:28:55 -0300)
Trying to boot from MMC1
spl: could not find mmc device 0. error: -19
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The reason for the boot failure is that that the SPL
size got greater than the 68KB limit (4KB header + 64KB max
size) as explained in include/configs/imx6_spl.h.
Remove the CONFIG_SPL_DM option, so that the SPL binary could
fit into the allowed size and the board can boot again.
Igor Opaniuk [Wed, 29 May 2019 10:00:43 +0000 (13:00 +0300)]
apalis-tk1: use UUID for rootfs
1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Wed, 29 May 2019 10:00:42 +0000 (13:00 +0300)]
apalis_imx6: use UUID for rootfs
1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Wed, 29 May 2019 10:00:41 +0000 (13:00 +0300)]
colibri_vf: use UUID for rootfs
Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Wed, 29 May 2019 10:00:40 +0000 (13:00 +0300)]
colibri-imx6ull: use UUID for rootfs
Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Wed, 29 May 2019 10:00:39 +0000 (13:00 +0300)]
colibri_imx7: use UUID for rootfs
Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Fri, 31 May 2019 16:00:20 +0000 (19:00 +0300)]
board: toradex: add apalis imx8qm 4gb wb it v1.0b module support
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT
V1.0B module. Unlike the V1.0A early access samples exclusively booting
from SD card, they are now strapped to boot from eFuses which are
factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Gigabit Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QM as of yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Jun Nie [Wed, 8 May 2019 06:38:33 +0000 (14:38 +0800)]
pico-imx7d: Add boot option for verified boot
Add boot option to boot from fitimage to support verified boot.
The boot script plain text file should be packed into fit blob as
image with name of bootscr.
Jun Nie [Wed, 8 May 2019 06:38:32 +0000 (14:38 +0800)]
pico-imx7d: Reserve region of memory to OPTEE
Subtracts CONFIG_OPTEE_TZDRAM_SIZE from the available DRAM size so that
the OPTEE memory is not override during u-boot relocation.
Note the OPTEE live in the end part of DRAM and OPTEE boot process will
itself subtract the DRAM region it lives in from the memory map passed
to Linux.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Jun Nie [Wed, 8 May 2019 06:38:30 +0000 (14:38 +0800)]
imx: mx7: Skip secure init in arch_cpu_init
Skip secure related initialization in arch_cpu_init if low level
init is skipped. Because these should be done in early stage
firmware, such as ARM trusted firmware.
Jun Nie [Wed, 8 May 2019 06:38:29 +0000 (14:38 +0800)]
mx7_common: Share configs to skip low level init
Share configs in mx7 to skip low level init if we are in the case where
OPTEE is loaded already (maybe by ARM Trusted Firmware) and that most of
the low level initialization is already done and that we may/should skip
it doing them here.
Fix the definition detection with size detection to decide whether to skip
it.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Heiko Schocher [Tue, 28 May 2019 11:44:31 +0000 (13:44 +0200)]
arm, imx, Makefile: fix u-boot-dtb.imx build in CONFIG_MULTI_DTB_FIT case
in case CONFIG_MULTI_DTB_FIT is set and u-boot-dtb.imx
image is build, currently u-boot-dtb.bin is used for
generating the u-boot-dtb.imx binary, which is wrong, as
it contains only a dtb blob not the fit.blob
Use instead the u-boot-fit-dtb.bin for generating
u-boot-dtb.imx which contains the fit.blob.
Ezequiel Garcia [Sat, 25 May 2019 22:19:41 +0000 (19:19 -0300)]
wandboard: Rework Makefile to prevent spl.o from being built
The spl.c source was entirely conditioned by CONFIG_SPL_BUILD.
Change this moving CONFIG_SPL_BUILD to be used in the Makefile,
which is slightly cleaner and more readable.
Revert "drivers/crypto/fsl: assign job-rings to non-TrustZone"
Commit 22191ac35344 ("drivers/crypto/fsl: assign job-rings to
non-TrustZone") breaks HABv4 encrypted boot support in the
following i.MX devices:
- i.MX6UL
- i.MX7S
- i.MX7D
- i.MX7ULP
For preparing a HABv4 encrypted boot image it's necessary to
encapsulate the generated DEK in a blob. In devices listed
above the blob generation function takes into consideration
the Job Ring TrustZone ownership configuration (JROWN_NS)
and can be only decapsulated by the same configuration.
The ROM code expects DEK blobs encapsulated by the Secure World
environments which commonly have JROWN_NS = 0.
As U-Boot is running in Secure World we must have JROWN_NS = 0
so the blobs generated by dek_blob tool can be decapsulated
by the ROM code.
Job-rings assignment is now handled in OP-TEE OS, this commit can
be safely reverted.
https://github.com/OP-TEE/optee_os/pull/2986
Fabio Estevam [Fri, 3 May 2019 17:05:04 +0000 (14:05 -0300)]
imx: Use a convenient default value for SYS_MALLOC_F_LEN
Commit 3a7c45f6a772 ("simple-bus: add DM_FLAG_PRE_RELOC flag to
simple-bus driver") causes some i.MX boards that were converted
to DM, such as warp7, to fail to boot.
As explained by Lukas Auer:
"With the patch, U-Boot probes the drivers for devices under simple-bus
device tree nodes in the pre-relocation device model. The default value
of CONFIG_SYS_MALLOC_F_LEN (0x400) leaves U-Boot with not enough memory to
do this, causing it to hang."
Fix this problem by providing a convenient default value for
CONFIG_SYS_MALLOC_F_LEN.
imx: hab: Increase CSF_SIZE for i.MX6 and i.MX7 devices
In certain i.MX devices the encrypted boot image is failing to boot.
According to AN12056 "Encrypted Boot on HABv4 and CAAM Enabled Devices"
it's necessary to pad CSF to 0x2000 and append DEK blob.
In this case the total image size in boot data structure must cover the
entire binary otherwise the dek_blob won't be copied to memory and image
won't be decrypted.
Increase CSF_SIZE to 0x4000 to avoid such issue when booting encrypted
boot images.
Extend size of the malloc() pool for use before relocation, from 0x400
(default one) to 0x2000 (CONFIG_SYS_MALLOC_F_LEN=0x2000),
as adding of DM_FLAG_PRE_RELOC flag to simple-bus driver introduced a
regression on multiple boards, because of more intensive usage of malloc()
pool and therefore a broken boot as the size of pool isn't sufficient.
Fixes: 3a7c45f6a7 ("simple-bus: add DM_FLAG_PRE_RELOC flag to simple-bus") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
power: pfuze100: Fix off by one error in voltage table handling
The code that sets a regulator by looking up the voltage in a table had
an off by one error. vsel_mask is a bitmask, not the number of table
entries, so a vsel_mask value of 0x7 indicates there are 8, not 7,
entries in the table.
Marcel Ziswiler [Fri, 31 May 2019 15:56:39 +0000 (18:56 +0300)]
board: toradex: add colibri imx8qxp 2gb wb it v1.0b module support
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Fri, 31 May 2019 15:56:38 +0000 (18:56 +0300)]
imx: fix building for i.mx8 without spl
Building with Travis CI complained and stopped with the following error:
+cc1: fatal error: opening output file spl/u-boot-spl.cfgout: No such
file or directory
+compilation terminated.
This fixes commit caceb739ea07 ("imx: build flash.bin for i.MX8") which
took SPL being enabled on i.MX8 for granted.
Adam Ford [Wed, 13 Mar 2019 15:49:22 +0000 (10:49 -0500)]
ARM: imx6logic: Stop overwriting fdt_file if manually set
The board file uses the processor type to determine what dtb file
is set. Unfortunately, if the user wants to manually set this,
it get gets overwritten upon boot. This patch adds a check to
see if the value is already set and only changes it if the value
is empty.
Tom Rini [Sat, 8 Jun 2019 00:39:32 +0000 (20:39 -0400)]
spl: Correct SPL_SIZE_LIMIT Kconfig option
When introduced this limit was an int but was then changed to hex
without noting as much in the prompt nor changing existing users. Put
this back to an int.
Tom Rini [Fri, 7 Jun 2019 22:03:18 +0000 (18:03 -0400)]
Merge branch '2019-06-07-master-imports'
- Include Heinrich's series to move the i.MX board size check function
to be more widely available.
- Include Simon Goldschmidt's patch to make it possible to have a more
accurate SPL size check applied.
This adds a size check for SPL that can dynamically check generated
SPL binaries (including devicetree) for a size limit that ensures
this image plus global data, heap and stack fit in initial SRAM.
Since some of these sizes are not available to make, a new host tool
'spl_size_limit' is added that dumps the resulting maximum size for
an SPL binary to stdout. This tool is used in toplevel Makefile to
implement the size check on SPL binaries.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Up to this point only a diagnostic message in mount_ubifs() using '%pUB' is
concerned by the change. Further patches are needed to adjust the UEFI
subsystem.
A unit test is provided inside the ut_print command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
projects / u-boot.git / log