--- /dev/null
+/*
+ * (C) Copyright 2013
+ * Gumstix Inc. <www.gumstix.com>
+ * Maintainer: Ash Charles <ash@gumstix.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <netdev.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mmc_host_def.h>
+#include <twl6030.h>
+#include <asm/emif.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/gpio.h>
+
+#include "duovero_mux_data.h"
+
+#define WIFI_EN 43
+
+#if defined(CONFIG_CMD_NET)
+#define SMSC_NRESET 45
+static void setup_net_chip(void);
+#endif
+
+#ifdef CONFIG_USB_EHCI
+#include <usb.h>
+#include <asm/arch/ehci.h>
+#include <asm/ehci-omap.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+const struct omap_sysinfo sysinfo = {
+ "Board: duovero\n"
+};
+
+struct omap4_scrm_regs *const scrm = (struct omap4_scrm_regs *)0x4a30a000;
+
+/**
+ * @brief board_init
+ *
+ * @return 0
+ */
+int board_init(void)
+{
+ gpmc_init();
+
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP4_DUOVERO;
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+ return 0;
+}
+
+/**
+ * @brief misc_init_r - Configure board specific configurations
+ * such as power configurations, ethernet initialization as phase2 of
+ * boot sequence
+ *
+ * @return 0
+ */
+int misc_init_r(void)
+{
+ int ret = 0;
+ u8 val;
+
+ /* wifi setup: first enable 32Khz clock from 6030 pmic */
+ val = 0xe1;
+ ret = i2c_write(TWL6030_CHIP_PM, 0xbe, 1, &val, 1);
+ if (ret)
+ printf("Failed to enable 32Khz clock to wifi module\n");
+
+ /* then setup WIFI_EN as an output pin and send reset pulse */
+ if (!gpio_request(WIFI_EN, "")) {
+ gpio_direction_output(WIFI_EN, 0);
+ gpio_set_value(WIFI_EN, 1);
+ udelay(1);
+ gpio_set_value(WIFI_EN, 0);
+ udelay(1);
+ gpio_set_value(WIFI_EN, 1);
+ }
+
+#if defined(CONFIG_CMD_NET)
+ setup_net_chip();
+#endif
+ return 0;
+}
+
+void set_muxconf_regs_essential(void)
+{
+ do_set_mux((*ctrl)->control_padconf_core_base,
+ core_padconf_array_essential,
+ sizeof(core_padconf_array_essential) /
+ sizeof(struct pad_conf_entry));
+
+ do_set_mux((*ctrl)->control_padconf_wkup_base,
+ wkup_padconf_array_essential,
+ sizeof(wkup_padconf_array_essential) /
+ sizeof(struct pad_conf_entry));
+
+ do_set_mux((*ctrl)->control_padconf_core_base,
+ core_padconf_array_non_essential,
+ sizeof(core_padconf_array_non_essential) /
+ sizeof(struct pad_conf_entry));
+
+ do_set_mux((*ctrl)->control_padconf_wkup_base,
+ wkup_padconf_array_non_essential,
+ sizeof(wkup_padconf_array_non_essential) /
+ sizeof(struct pad_conf_entry));
+}
+
+#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC)
+int board_mmc_init(bd_t *bis)
+{
+ return omap_mmc_init(0, 0, 0, -1, -1);
+}
+#endif
+
+
+#if defined(CONFIG_CMD_NET)
+
+#define GPMC_SIZE_16M 0xF
+#define GPMC_BASEADDR_MASK 0x3F
+#define GPMC_CS_ENABLE 0x1
+
+static void enable_gpmc_net_config(const u32 *gpmc_config, struct gpmc_cs *cs,
+ u32 base, u32 size)
+{
+ writel(0, &cs->config7);
+ sdelay(1000);
+ /* Delay for settling */
+ writel(gpmc_config[0], &cs->config1);
+ writel(gpmc_config[1], &cs->config2);
+ writel(gpmc_config[2], &cs->config3);
+ writel(gpmc_config[3], &cs->config4);
+ writel(gpmc_config[4], &cs->config5);
+ writel(gpmc_config[5], &cs->config6);
+
+ /*
+ * Enable the config. size is the CS size and goes in
+ * bits 11:8. We set bit 6 to enable this CS and the base
+ * address goes into bits 5:0.
+ */
+ writel((size << 8) | (GPMC_CS_ENABLE << 6) |
+ ((base >> 24) & GPMC_BASEADDR_MASK),
+ &cs->config7);
+
+ sdelay(2000);
+}
+
+/* GPMC CS configuration for an SMSC LAN9221 ethernet controller */
+#define NET_LAN9221_GPMC_CONFIG1 0x2a001203
+#define NET_LAN9221_GPMC_CONFIG2 0x000a0a02
+#define NET_LAN9221_GPMC_CONFIG3 0x00020200
+#define NET_LAN9221_GPMC_CONFIG4 0x0a030a03
+#define NET_LAN9221_GPMC_CONFIG5 0x000a0a0a
+#define NET_LAN9221_GPMC_CONFIG6 0x8a070707
+#define NET_LAN9221_GPMC_CONFIG7 0x00000f6c
+
+/* GPMC definitions for LAN9221 chips on expansion boards */
+static const u32 gpmc_lan_config[] = {
+ NET_LAN9221_GPMC_CONFIG1,
+ NET_LAN9221_GPMC_CONFIG2,
+ NET_LAN9221_GPMC_CONFIG3,
+ NET_LAN9221_GPMC_CONFIG4,
+ NET_LAN9221_GPMC_CONFIG5,
+ NET_LAN9221_GPMC_CONFIG6,
+ /*CONFIG7- computed as params */
+};
+
+/*
+ * Routine: setup_net_chip
+ * Description: Setting up the configuration GPMC registers specific to the
+ * Ethernet hardware.
+ */
+static void setup_net_chip(void)
+{
+ enable_gpmc_net_config(gpmc_lan_config, &gpmc_cfg->cs[5], 0x2C000000,
+ GPMC_SIZE_16M);
+
+ /* Make GPIO SMSC_NRESET as output pin and send reset pulse */
+ if (!gpio_request(SMSC_NRESET, "")) {
+ gpio_direction_output(SMSC_NRESET, 0);
+ gpio_set_value(SMSC_NRESET, 1);
+ udelay(1);
+ gpio_set_value(SMSC_NRESET, 0);
+ udelay(1);
+ gpio_set_value(SMSC_NRESET, 1);
+ }
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_SMC911X
+ rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+#endif
+ return rc;
+}
+
+#ifdef CONFIG_USB_EHCI
+
+static struct omap_usbhs_board_data usbhs_bdata = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+ struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+ int ret;
+ unsigned int utmi_clk;
+ u32 auxclk, altclksrc;
+
+ /* Now we can enable our port clocks */
+ utmi_clk = readl((void *)CM_L3INIT_HSUSBHOST_CLKCTRL);
+ utmi_clk |= HSUSBHOST_CLKCTRL_CLKSEL_UTMI_P1_MASK;
+ setbits_le32((void *)CM_L3INIT_HSUSBHOST_CLKCTRL, utmi_clk);
+
+ auxclk = readl(&scrm->auxclk3);
+ /* Select sys_clk */
+ auxclk &= ~AUXCLK_SRCSELECT_MASK;
+ auxclk |= AUXCLK_SRCSELECT_SYS_CLK << AUXCLK_SRCSELECT_SHIFT;
+ /* Set the divisor to 2 */
+ auxclk &= ~AUXCLK_CLKDIV_MASK;
+ auxclk |= AUXCLK_CLKDIV_2 << AUXCLK_CLKDIV_SHIFT;
+ /* Request auxilary clock #3 */
+ auxclk |= AUXCLK_ENABLE_MASK;
+ writel(auxclk, &scrm->auxclk3);
+
+ altclksrc = readl(&scrm->altclksrc);
+
+ /* Activate alternate system clock supplier */
+ altclksrc &= ~ALTCLKSRC_MODE_MASK;
+ altclksrc |= ALTCLKSRC_MODE_ACTIVE;
+
+ /* enable clocks */
+ altclksrc |= ALTCLKSRC_ENABLE_INT_MASK | ALTCLKSRC_ENABLE_EXT_MASK;
+
+ writel(altclksrc, &scrm->altclksrc);
+
+ ret = omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+int ehci_hcd_stop(int index)
+{
+ return omap_ehci_hcd_stop();
+}
+#endif
+
+/*
+ * get_board_rev() - get board revision
+ */
+u32 get_board_rev(void)
+{
+ return 0x20;
+}
--- /dev/null
+/*
+ * (C) Copyright 2012
+ * Gumstix Incorporated, <www.gumstix.com>
+ * Maintainer: Ash Charles <ash@gumstix.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef _DUOVERO_MUX_DATA_H_
+#define _DUOVERO_MUX_DATA_H_
+
+#include <asm/arch/mux_omap4.h>
+
+const struct pad_conf_entry core_padconf_array_essential[] = {
+ {SDMMC1_CLK, (PTU | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc1_clk */
+ {SDMMC1_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_cmd */
+ {SDMMC1_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat0 */
+ {SDMMC1_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat1 */
+ {SDMMC1_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat2 */
+ {SDMMC1_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat3 */
+ {I2C1_SCL, (PTU | IEN | M0)}, /* i2c1_scl */
+ {I2C1_SDA, (PTU | IEN | M0)}, /* i2c1_sda */
+ {I2C2_SCL, (PTU | IEN | M0)}, /* i2c2_scl */
+ {I2C2_SDA, (PTU | IEN | M0)}, /* i2c2_sda */
+ {I2C3_SCL, (PTU | IEN | M0)}, /* i2c3_scl */
+ {I2C3_SDA, (PTU | IEN | M0)}, /* i2c3_sda */
+ {I2C4_SCL, (PTU | IEN | M0)}, /* i2c4_scl */
+ {I2C4_SDA, (PTU | IEN | M0)}, /* i2c4_sda */
+ {UART3_CTS_RCTX, (PTU | IEN | M0)}, /* uart3_tx */
+ {UART3_RTS_SD, (M0)}, /* uart3_rts_sd */
+ {UART3_RX_IRRX, (PTU | IEN | M0)}, /* uart3_rx */
+ {UART3_TX_IRTX, (M0)} /* uart3_tx */
+};
+
+const struct pad_conf_entry wkup_padconf_array_essential[] = {
+ {PAD1_SR_SCL, (PTU | IEN | M0)}, /* sr_scl */
+ {PAD0_SR_SDA, (PTU | IEN | M0)}, /* sr_sda */
+ {PAD1_SYS_32K, (IEN | M0)} /* sys_32k */
+};
+
+const struct pad_conf_entry core_padconf_array_non_essential[] = {
+ {GPMC_AD0, (PTU | IEN | M0)}, /* gpmc_ad0 */
+ {GPMC_AD1, (PTU | IEN | M0)}, /* gpmc_ad1 */
+ {GPMC_AD2, (PTU | IEN | M0)}, /* gpmc_ad2 */
+ {GPMC_AD3, (PTU | IEN | M0)}, /* gpmc_ad3 */
+ {GPMC_AD4, (PTU | IEN | M0)}, /* gpmc_ad4 */
+ {GPMC_AD5, (PTU | IEN | M0)}, /* gpmc_ad5 */
+ {GPMC_AD6, (PTU | IEN | M0)}, /* gpmc_ad6 */
+ {GPMC_AD7, (PTU | IEN | M0)}, /* gpmc_ad7 */
+ {GPMC_AD8, (PTU | IEN | M0)}, /* gpmc_ad8 */
+ {GPMC_AD9, (PTU | IEN | M0)}, /* gpmc_ad9 */
+ {GPMC_AD10, (PTU | IEN | M0)}, /* gpmc_ad10 */
+ {GPMC_AD11, (PTU | IEN | M0)}, /* gpmc_ad11 */
+ {GPMC_AD12, (PTU | IEN | M0)}, /* gpmc_ad12 */
+ {GPMC_AD13, (PTU | IEN | M0)}, /* gpmc_ad13 */
+ {GPMC_AD14, (PTU | IEN | M0)}, /* gpmc_ad14 */
+ {GPMC_AD15, (PTU | IEN | M0)}, /* gpmc_ad15 */
+ {GPMC_A16, (PTU | IEN | M3)}, /* gpio_40 */
+ {GPMC_A17, (PTU | IEN | M3)}, /* gpio_41 - hdmi_ls_oe */
+ {GPMC_A18, (PTU | IEN | M3)}, /* gpio_42 */
+ {GPMC_A19, (PTU | IEN | M3)}, /* gpio_43 - wifi_en */
+ {GPMC_A20, (PTU | IEN | M3)}, /* gpio_44 - eth_irq */
+ {GPMC_A21, (PTU | IEN | M3)}, /* gpio_45 - eth_nreset */
+ {GPMC_A22, (PTU | IEN | M3)}, /* gpio_46 - eth_pme */
+ {GPMC_A23, (PTU | IEN | M3)}, /* gpio_47 */
+ {GPMC_A24, (PTU | IEN | M3)}, /* gpio_48 - eth_mdix */
+ {GPMC_A25, (PTU | IEN | M3)}, /* gpio_49 - bt_wakeup */
+ {GPMC_NCS0, (PTU | M0)}, /* gpmc_ncs0 */
+ {GPMC_NCS1, (PTU | M0)}, /* gpmc_ncs1 */
+ {GPMC_NCS2, (PTU | M0)}, /* gpmc_ncs2 */
+ {GPMC_NCS3, (PTU | IEN | M3)}, /* gpio_53 */
+ {C2C_DATA12, (PTU | M0)}, /* gpmc_ncs4 */
+ {C2C_DATA13, (PTU | M0)}, /* gpmc_ncs5 - eth_cs */
+ {GPMC_NWP, (PTU | IEN | M0)}, /* gpmc_nwp */
+ {GPMC_CLK, (PTU | IEN | M0)}, /* gpmc_clk */
+ {GPMC_NADV_ALE, (PTU | M0)}, /* gpmc_nadv_ale */
+ {GPMC_NBE0_CLE, (PTU | M0)}, /* gpmc_nbe0_cle */
+ {GPMC_NBE1, (PTU | M0)}, /* gpmc_nbe1 */
+ {GPMC_WAIT0, (PTU | IEN | M0)}, /* gpmc_wait0 */
+ {GPMC_WAIT1, (PTU | IEN | M0)}, /* gpio_62 - usbh_nreset */
+ {GPMC_NOE, (PTU | M0)}, /* gpmc_noe */
+ {GPMC_NWE, (PTU | M0)}, /* gpmc_nwe */
+ {HDMI_HPD, (PTD | IEN | M3)}, /* gpio_63 - hdmi_hpd */
+ {HDMI_CEC, (PTU | IEN | M0)}, /* hdmi_cec */
+ {HDMI_DDC_SCL, (M0)}, /* hdmi_ddc_scl */
+ {HDMI_DDC_SDA, (IEN | M0)}, /* hdmi_ddc_sda */
+ {CSI21_DX0, (IEN | M0)}, /* csi21_dx0 */
+ {CSI21_DY0, (IEN | M0)}, /* csi21_dy0 */
+ {CSI21_DX1, (IEN | M0)}, /* csi21_dx1 */
+ {CSI21_DY1, (IEN | M0)}, /* csi21_dy1 */
+ {CSI21_DX2, (IEN | M0)}, /* csi21_dx2 */
+ {CSI21_DY2, (IEN | M0)}, /* csi21_dy2 */
+ {CSI21_DX3, (IEN | M0)}, /* csi21_dx3 */
+ {CSI21_DY3, (IEN | M0)}, /* csi21_dy3 */
+ {CSI21_DX4, (IEN | M0)}, /* csi21_dx4 */
+ {CSI21_DY4, (IEN | M0)}, /* csi21_dy4 */
+ {CSI22_DX0, (IEN | M0)}, /* csi22_dx0 */
+ {CSI22_DY0, (IEN | M0)}, /* csi22_dy0 */
+ {CSI22_DX1, (IEN | M0)}, /* csi22_dx1 */
+ {CSI22_DY1, (IEN | M0)}, /* csi22_dy1 */
+ {USBB1_ULPITLL_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M4)},/* usbb1_ulpiphy_clk */
+ {USBB1_ULPITLL_STP, (OFF_EN | OFF_OUT_PTD | M4)}, /* usbb1_ulpiphy_stp */
+ {USBB1_ULPITLL_DIR, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dir */
+ {USBB1_ULPITLL_NXT, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_nxt */
+ {USBB1_ULPITLL_DAT0, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat0 */
+ {USBB1_ULPITLL_DAT1, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat1 */
+ {USBB1_ULPITLL_DAT2, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat2 */
+ {USBB1_ULPITLL_DAT3, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat3 */
+ {USBB1_ULPITLL_DAT4, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat4 */
+ {USBB1_ULPITLL_DAT5, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat5 */
+ {USBB1_ULPITLL_DAT6, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat6 */
+ {USBB1_ULPITLL_DAT7, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat7 */
+ {USBB1_HSIC_DATA, (PTU | IEN | M3)}, /* gpio_96 - usbh_cpen */
+ {USBB1_HSIC_STROBE, (PTU | IEN | M3)}, /* gpio_97 - usbh_reset */
+ {ABE_MCBSP2_CLKX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_clkx */
+ {ABE_MCBSP2_DR, (IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dr */
+ {ABE_MCBSP2_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dx */
+ {ABE_MCBSP2_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_fsx */
+ {ABE_PDM_UL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_ul_data */
+ {ABE_PDM_DL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_dl_data */
+ {ABE_PDM_FRAME, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_frame */
+ {ABE_PDM_LB_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_lb_clk */
+ {ABE_CLKS, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_clks */
+ {ABE_DMIC_CLK1, (M0)}, /* abe_dmic_clk1 */
+ {ABE_DMIC_DIN1, (IEN | M0)}, /* abe_dmic_din1 */
+ {ABE_DMIC_DIN2, (IEN | M0)}, /* abe_dmic_din2 */
+ {ABE_DMIC_DIN3, (IEN | M0)}, /* abe_dmic_din3 */
+ {UART2_CTS, (PTU | IEN | M0)}, /* uart2_cts */
+ {UART2_RTS, (M0)}, /* uart2_rts */
+ {UART2_RX, (PTU | IEN | M0)}, /* uart2_rx */
+ {UART2_TX, (M0)}, /* uart2_tx */
+ {HDQ_SIO, (M0)}, /* hdq-sio */
+ {MCSPI1_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_clk */
+ {MCSPI1_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_somi */
+ {MCSPI1_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_simo */
+ {MCSPI1_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_cs0 */
+ {MCSPI1_CS1, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_cs1 */
+ {SDMMC5_CLK, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_clk */
+ {SDMMC5_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_cmd */
+ {SDMMC5_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat0 */
+ {SDMMC5_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat1 */
+ {SDMMC5_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat2 */
+ {SDMMC5_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat3 */
+ {MCSPI4_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_clk */
+ {MCSPI4_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_simo */
+ {MCSPI4_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_somi */
+ {MCSPI4_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_cs0 */
+ {UART4_RX, (IEN | PTU | M0)}, /* uart4_rx */
+ {UART4_TX, (M0)}, /* uart4_tx */
+ {USBB2_ULPITLL_CLK, (PTU | IEN | M3)}, /* gpio_157 - start_adc */
+ {USBB2_ULPITLL_STP, (PTU | IEN | M3)}, /* gpio_158 - spi_nirq */
+ {USBB2_ULPITLL_DIR, (PTU | IEN | M3)}, /* gpio_159 - bt_nreset */
+ {USBB2_ULPITLL_NXT, (PTU | IEN | M3)}, /* gpio_160 - audio_pwron*/
+ {USBB2_ULPITLL_DAT0, (PTU | IEN | M3)}, /* gpio_161 - bid_0 */
+ {USBB2_ULPITLL_DAT1, (PTU | IEN | M3)}, /* gpio_162 - bid_1 */
+ {USBB2_ULPITLL_DAT2, (PTU | IEN | M3)}, /* gpio_163 - bid_2 */
+ {USBB2_ULPITLL_DAT3, (PTU | IEN | M3)}, /* gpio_164 - bid_3 */
+ {USBB2_ULPITLL_DAT4, (PTU | IEN | M3)}, /* gpio_165 - bid_4 */
+ {USBB2_ULPITLL_DAT5, (PTU | IEN | M3)}, /* gpio_166 - ts_irq*/
+ {USBB2_ULPITLL_DAT6, (PTU | IEN | M3)}, /* gpio_167 - gps_pps */
+ {USBB2_ULPITLL_DAT7, (PTU | IEN | M3)}, /* gpio_168 */
+ {USBB2_HSIC_DATA, (PTU | IEN | M3)}, /* gpio_169 */
+ {USBB2_HSIC_STROBE, (PTU | IEN | M3)}, /* gpio_170 */
+ {UNIPRO_TX1, (PTU | IEN | M3)}, /* gpio_173 */
+ {USBA0_OTG_CE, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* usba0_otg_ce */
+ {USBA0_OTG_DP, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dp */
+ {USBA0_OTG_DM, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dm */
+ {SYS_NIRQ1, (PTU | IEN | M0)}, /* sys_nirq1 */
+ {SYS_NIRQ2, (PTU | IEN | M0)}, /* sys_nirq2 */
+ {SYS_BOOT0, (M0)}, /* sys_boot0 */
+ {SYS_BOOT1, (M0)}, /* sys_boot1 */
+ {SYS_BOOT2, (M0)}, /* sys_boot2 */
+ {SYS_BOOT3, (M0)}, /* sys_boot3 */
+ {SYS_BOOT4, (M0)}, /* sys_boot4 */
+ {SYS_BOOT5, (M0)}, /* sys_boot5 */
+ {DPM_EMU0, (IEN | M0)}, /* dpm_emu0 */
+ {DPM_EMU1, (IEN | M0)}, /* dpm_emu1 */
+ {DPM_EMU16, (PTU | IEN | M3)}, /* gpio_27 */
+ {DPM_EMU17, (PTU | IEN | M3)}, /* gpio_28 */
+ {DPM_EMU18, (PTU | IEN | M3)}, /* gpio_29 */
+ {DPM_EMU19, (PTU | IEN | M3)}, /* gpio_30 */
+};
+
+const struct pad_conf_entry wkup_padconf_array_non_essential[] = {
+ {PAD1_FREF_XTAL_IN, (M0)}, /* fref_xtal_in */
+ {PAD0_FREF_SLICER_IN, (M0)}, /* fref_slicer_in */
+ {PAD1_FREF_CLK_IOREQ, (M0)}, /* fref_clk_ioreq */
+ {PAD0_FREF_CLK0_OUT, (M7)}, /* safe mode */
+ {PAD1_FREF_CLK3_REQ, M7}, /* safe mode */
+ {PAD0_FREF_CLK3_OUT, (M0)}, /* fref_clk3_out */
+ {PAD0_SYS_NRESPWRON, (M0)}, /* sys_nrespwron */
+ {PAD1_SYS_NRESWARM, (M0)}, /* sys_nreswarm */
+ {PAD0_SYS_PWR_REQ, (PTU | M0)}, /* sys_pwr_req */
+ {PAD1_SYS_PWRON_RESET, (M3)}, /* gpio_wk29 */
+ {PAD0_SYS_BOOT6, (M0)}, /* sys_boot6 */
+ {PAD1_SYS_BOOT7, (M0)}, /* sys_boot7 */
+};
+
+
+#endif /* _DUOVERO_MUX_DATA_H_ */
projects / u-boot.git / commitdiff