--- /dev/null
+/*
+ * ICP DAS LP-8x4x Support
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ * adapted from Voipac PXA270 Support by
+ * Copyright (C) 2013 Sergey Yanovich <ynvich@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/regs-mmc.h>
+#include <asm/arch/pxa.h>
+#include <netdev.h>
+#include <serial.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+int board_init(void)
+{
+ /* We have RAM, disable cache */
+ dcache_disable();
+ icache_disable();
+
+ /* memory and cpu-speed are setup before relocation */
+ /* so we do _nothing_ here */
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = 0xa0000100;
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ pxa2xx_dram_init();
+ gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
+ return 0;
+}
+
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+}
+
+#ifdef CONFIG_CMD_MMC
+int board_mmc_init(bd_t *bis)
+{
+ pxa_mmc_register(0);
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_CMD_USB
+int usb_board_init(void)
+{
+ writel((UHCHR | UHCHR_PCPL | UHCHR_PSPL) &
+ ~(UHCHR_SSEP0 | UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSE),
+ UHCHR);
+
+ writel(readl(UHCHR) | UHCHR_FSBIR, UHCHR);
+
+ while (readl(UHCHR) & UHCHR_FSBIR)
+ continue; /* required by checkpath.pl */
+
+ writel(readl(UHCHR) & ~UHCHR_SSE, UHCHR);
+ writel((UHCHIE_UPRIE | UHCHIE_RWIE), UHCHIE);
+
+ /* Clear any OTG Pin Hold */
+ if (readl(PSSR) & PSSR_OTGPH)
+ writel(readl(PSSR) | PSSR_OTGPH, PSSR);
+
+ writel(readl(UHCRHDA) & ~(0x200), UHCRHDA);
+ writel(readl(UHCRHDA) | 0x100, UHCRHDA);
+
+ /* Set port power control mask bits, only 3 ports. */
+ writel(readl(UHCRHDB) | (0x7<<17), UHCRHDB);
+
+ /* enable port 2 */
+ writel(readl(UP2OCR) | UP2OCR_HXOE | UP2OCR_HXS |
+ UP2OCR_DMPDE | UP2OCR_DPPDE, UP2OCR);
+
+ return 0;
+}
+
+void usb_board_init_fail(void)
+{
+ return;
+}
+
+void usb_board_stop(void)
+{
+ writel(readl(UHCHR) | UHCHR_FHR, UHCHR);
+ udelay(11);
+ writel(readl(UHCHR) & ~UHCHR_FHR, UHCHR);
+
+ writel(readl(UHCCOMS) | 1, UHCCOMS);
+ udelay(10);
+
+ writel(readl(CKEN) & ~CKEN10_USBHOST, CKEN);
+
+ return;
+}
+#endif
+
+#ifdef CONFIG_DRIVER_DM9000
+void lp8x4x_eth1_mac_init(void)
+{
+ u8 eth1addr[8];
+ int i;
+ u8 reg;
+
+ eth_getenv_enetaddr_by_index("eth", 1, eth1addr);
+ if (!is_valid_ether_addr(eth1addr))
+ return;
+
+ for (i = 0, reg = 0x10; i < 6; i++, reg++) {
+ writeb(reg, (u8 *)(DM9000_IO_2));
+ writeb(eth1addr[i], (u8 *)(DM9000_DATA_2));
+ }
+}
+
+int board_eth_init(bd_t *bis)
+{
+ lp8x4x_eth1_mac_init();
+ return dm9000_initialize(bis);
+}
+#endif
--- /dev/null
+/*
+ * ICP DAS LP-8x4x configuration file
+ *
+ * Copyright (C) 2013 Sergey Yanovich <ynvich@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Board Configuration Options
+ */
+#define CONFIG_CPU_PXA27X /* Marvell PXA270 CPU */
+#define MACH_TYPE_LP8X4X 4539 /* ICP DAS LP-8x4x */
+#define CONFIG_MACH_TYPE MACH_TYPE_LP8X4X
+#define CONFIG_SYS_TEXT_BASE 0x00000000
+
+#define CONFIG_SYS_MALLOC_LEN (128*1024)
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_BOOTCOMMAND \
+ "bootm 80000;"
+
+#define CONFIG_BOOTARGS \
+ "console=ttySA0,115200 mem=128M root=/dev/mmcblk0p1 rw" \
+ "init=/sbin/init rootfstype=ext3"
+
+#define CONFIG_TIMESTAMP
+#define CONFIG_BOOTDELAY 2 /* Autoboot delay */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_LZMA /* LZMA compression support */
+#undef CONFIG_OF_LIBFDT
+
+/*
+ * Serial Console Configuration
+ */
+#define CONFIG_PXA_SERIAL
+#define CONFIG_FFUART 1
+#define CONFIG_CONS_INDEX 3
+#define CONFIG_BAUDRATE 115200
+
+/*
+ * Bootloader Components Configuration
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_ENV
+#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_USB
+#undef CONFIG_LCD
+#undef CONFIG_CMD_IDE
+
+/*
+ * Networking Configuration
+ * chip on the ICPDAS LINPAC board
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+
+#define CONFIG_DRIVER_DM9000 1
+#define CONFIG_DM9000_BASE 0x0C000000
+#define DM9000_IO 0x0C000000
+#define DM9000_DATA 0x0C004000
+#define DM9000_IO_2 0x0D000000
+#define DM9000_DATA_2 0x0D004000
+#define CONFIG_NET_RETRY_COUNT 10
+
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#endif
+
+/*
+ * MMC Card Configuration
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_PXA_MMC_GENERIC
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * KGDB
+ */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* kgdb serial port speed */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * HUSH Shell Configuration
+ */
+#define CONFIG_SYS_HUSH_PARSER 1
+
+#undef CONFIG_SYS_LONGHELP
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "$ "
+#else
+#define CONFIG_SYS_PROMPT "=> "
+#endif
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_PBSIZE \
+ (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_DEVICE_NULLDEV 1
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_AUTO_COMPLETE 1
+
+/*
+ * Clock Configuration
+ */
+#define CONFIG_SYS_HZ 1000 /* Timer @ 3250000 Hz */
+
+/*
+ * DRAM Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
+#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
+
+#define CONFIG_SYS_DRAM_BASE 0xa0000000 /* CS0 */
+#define CONFIG_SYS_DRAM_SIZE 0x08000000 /* 128 MB DRAM */
+
+#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
+
+#define CONFIG_SYS_LOAD_ADDR 0xa0008000
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+/* Use first 64kb bank of the internal SRAM */
+#define CONFIG_SYS_INIT_SP_ADDR 0x5c010000
+
+/*
+ * NOR FLASH
+ */
+#define CONFIG_SYS_MONITOR_BASE 0x0
+#define CONFIG_SYS_MONITOR_LEN 0x40000
+#define CONFIG_ENV_ADDR \
+ (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SIZE 0x40000
+#define CONFIG_ENV_SECT_SIZE 0x40000
+
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_2 0x02000000 /* Flash Bank #2 */
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER 1
+
+#define CONFIG_SYS_MAX_FLASH_SECT (4 + 255)
+#define CONFIG_SYS_MAX_FLASH_BANKS 2
+#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 }
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT (25*CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (25*CONFIG_SYS_HZ)
+
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
+#define CONFIG_SYS_FLASH_PROTECTION 1
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+
+/*
+ * GPIO settings
+ */
+#define CONFIG_SYS_GPSR0_VAL 0x0808c014
+#define CONFIG_SYS_GPSR1_VAL 0x00cf0002
+#define CONFIG_SYS_GPSR2_VAL 0x0221c000
+#define CONFIG_SYS_GPSR3_VAL 0x00020000
+
+#define CONFIG_SYS_GPCR0_VAL 0x00000000
+#define CONFIG_SYS_GPCR1_VAL 0x0000ab80
+#define CONFIG_SYS_GPCR2_VAL 0x00100000
+#define CONFIG_SYS_GPCR3_VAL 0x0
+
+#define CONFIG_SYS_GPDR0_VAL 0xc0e9ddf4
+#define CONFIG_SYS_GPDR1_VAL 0xfcffab83
+#define CONFIG_SYS_GPDR2_VAL 0x02f1ffff
+#define CONFIG_SYS_GPDR3_VAL 0x00021b81
+
+#define CONFIG_SYS_GAFR0_L_VAL 0x80000000
+#define CONFIG_SYS_GAFR0_U_VAL 0xa5e54018
+#define CONFIG_SYS_GAFR1_L_VAL 0x999a955a
+#define CONFIG_SYS_GAFR1_U_VAL 0xaaa5a00a
+#define CONFIG_SYS_GAFR2_L_VAL 0xaaaaaaaa
+#define CONFIG_SYS_GAFR2_U_VAL 0x55f0a402
+#define CONFIG_SYS_GAFR3_L_VAL 0x540a950c
+#define CONFIG_SYS_GAFR3_U_VAL 0x00001599
+
+#define CONFIG_SYS_PSSR_VAL 0x32
+
+/*
+ * Clock settings
+ */
+#define CONFIG_SYS_CKEN 0x005002c0
+#define CONFIG_SYS_CCCR 0x02000290
+#define CONFIG_SYS_CLKCFG 0x0000000b
+
+/*
+ * Memory settings
+ */
+#define CONFIG_SYS_MSC0_VAL 0x2bd8aad2
+#define CONFIG_SYS_MSC1_VAL 0xb8c9b8dc
+#define CONFIG_SYS_MSC2_VAL 0xfff9b8c9
+#define CONFIG_SYS_FLYCNFG_VAL 0x00010001
+#define CONFIG_SYS_MDREFR_VAL 0x2093e018
+#define CONFIG_SYS_MDCNFG_VAL 0x890009d1
+#define CONFIG_SYS_MDMRS_VAL 0x00220022
+#define CONFIG_SYS_SXCNFG_VAL 0x40044004
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define CONFIG_SYS_MECR_VAL 0x00000001
+#define CONFIG_SYS_MCMEM0_VAL 0x0000c497
+#define CONFIG_SYS_MCMEM1_VAL 0x0000c497
+#define CONFIG_SYS_MCATT0_VAL 0x0000c497
+#define CONFIG_SYS_MCATT1_VAL 0x0000c497
+#define CONFIG_SYS_MCIO0_VAL 0x00008407
+#define CONFIG_SYS_MCIO1_VAL 0x00008407
+
+/*
+ * LCD
+ */
+#ifdef CONFIG_LCD
+#define CONFIG_VOIPAC_LCD
+#endif
+
+/*
+ * USB
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
+#define CONFIG_SYS_USB_OHCI_BOARD_INIT
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
+#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x4C000000
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "lp8x4x"
+#define CONFIG_USB_STORAGE
+#endif
+
+#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff