board: mx6sabreauto: Remove the non-DM code

Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabreauto board file.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

diff --git a/board/freescale/mx6sabreauto/mx6sabreauto.c b/board/freescale/mx6sabreauto/mx6sabreauto.c
index c7e3e6712daf3006fa38b980b36b853ebd3f62f4..dd72de9fc6439bc618a489f6b8f8f5e54a367ab6 100644 (file)
--- a/board/freescale/mx6sabreauto/mx6sabreauto.c
+++ b/board/freescale/mx6sabreauto/mx6sabreauto.c
@@ -159,44 +159,6 @@ static iomux_v3_cfg_t const port_exp[] = {
        IOMUX_PADS(PAD_SD2_DAT0__GPIO1_IO15     | MUX_PAD_CTRL(NO_PAD_CTRL)),
 };
 
-/*Define for building port exp gpio, pin starts from 0*/
-#define PORTEXP_IO_NR(chip, pin) \
-       ((chip << 5) + pin)
-
-/*Get the chip addr from a ioexp gpio*/
-#define PORTEXP_IO_TO_CHIP(gpio_nr) \
-       (gpio_nr >> 5)
-
-/*Get the pin number from a ioexp gpio*/
-#define PORTEXP_IO_TO_PIN(gpio_nr) \
-       (gpio_nr & 0x1f)
-
-static int port_exp_direction_output(unsigned gpio, int value)
-{
-       int ret;
-
-       i2c_set_bus_num(2);
-       ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio));
-       if (ret)
-               return ret;
-
-       ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio),
-               (1 << PORTEXP_IO_TO_PIN(gpio)),
-               (PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio)));
-
-       if (ret)
-               return ret;
-
-       ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio),
-               (1 << PORTEXP_IO_TO_PIN(gpio)),
-               (value << PORTEXP_IO_TO_PIN(gpio)));
-
-       if (ret)
-               return ret;
-
-       return 0;
-}
-
 #ifdef CONFIG_MTD_NOR_FLASH
 static iomux_v3_cfg_t const eimnor_pads[] = {
        IOMUX_PADS(PAD_EIM_D16__EIM_DATA16      | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
@@ -681,19 +643,10 @@ int checkboard(void)
 }
 
 #ifdef CONFIG_USB_EHCI_MX6
-#define USB_HOST1_PWR     PORTEXP_IO_NR(0x32, 7)
-#define USB_OTG_PWR       PORTEXP_IO_NR(0x34, 1)
-
-iomux_v3_cfg_t const usb_otg_pads[] = {
-       IOMUX_PADS(PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
 int board_ehci_hcd_init(int port)
 {
        switch (port) {
        case 0:
-               SETUP_IOMUX_PADS(usb_otg_pads);
-
                /*
                  * Set daisy chain for otg_pin_id on 6q.
                 *  For 6dl, this bit is reserved.
@@ -708,29 +661,6 @@ int board_ehci_hcd_init(int port)
        }
        return 0;
 }
-
-int board_ehci_power(int port, int on)
-{
-       switch (port) {
-       case 0:
-               if (on)
-                       port_exp_direction_output(USB_OTG_PWR, 1);
-               else
-                       port_exp_direction_output(USB_OTG_PWR, 0);
-               break;
-       case 1:
-               if (on)
-                       port_exp_direction_output(USB_HOST1_PWR, 1);
-               else
-                       port_exp_direction_output(USB_HOST1_PWR, 0);
-               break;
-       default:
-               printf("MXC USB port %d not yet supported\n", port);
-               return -EINVAL;
-       }
-
-       return 0;
-}
 #endif
 
 #ifdef CONFIG_SPL_BUILD