]> git.dujemihanovic.xyz Git - u-boot.git/commitdiff
i2c: mxc: refactor i2c driver and support dm
authorPeng Fan <Peng.Fan@freescale.com>
Thu, 14 May 2015 23:29:12 +0000 (07:29 +0800)
committerSimon Glass <sjg@chromium.org>
Fri, 15 May 2015 00:49:36 +0000 (18:49 -0600)
1. Introduce a new structure `struct mxc_i2c_bus`, this structure will
   used for non-DM and DM.
2. Remove `struct mxc_i2c_regs` structure, but use register offset to access
   registers based on `base` entry of `struct mxc_i2c_bus`.
3. Remove most `#ifdef I2C_QUIRK_REG`. Using driver_data to contain platform
   flags. A new flag is introduced, I2C_QUIRK_FLAG.
4. Most functions use `struct mxc_i2c_bus` as one of the parameters.
   Make most functions common to DM and non-DM, try to avoid duplicated code.
5. Support DM, but pinctrl is not included. Pinmux setting is still set
   by setup_i2c, but we do not need bus_i2c_init for DM.
6. struct i2c_parms and struct sram_data are removed.
7. Remove bus_i2c_read bus_i2c_write prototype in header file. The frist
   paramter of bus_i2c_init is modified to i2c index. Add new prototype
   i2c_idle_bus and force_bus_idle. Since bus_i2c_init is not good for
   DM I2C and pinctrl is missed, we use a weak function for i2c_idle_bus.
   Board file take the responsibility to implement this function, like this:
   "
   int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus)
   {
   if (i2c_bus->index == 0)
   force_bus_idle(i2c_pads_info0);
   else if (i2c_bus->index == 1)
   force_bus_idle(i2c_pads_info1);
   else
   xxxxxx
   }
   "
8. Introduce a weak function, enable_i2c_clk
9. Tested on an i.MX7 platform. Log info:
 => dm tree
 Class       Probed   Name
 ----------------------------------------
 root        [ + ]    root_driver
 simple_bus  [   ]    |-- soc
 simple_bus  [   ]    |   |-- aips-bus@30000000
 simple_bus  [   ]    |   |   |-- anatop@30360000
 simple_bus  [   ]    |   |   `-- snvs@30370000
 simple_bus  [   ]    |   |-- aips-bus@30400000
 simple_bus  [   ]    |   `-- aips-bus@30800000
 i2c         [   ]    |       |-- i2c@30a20000
 i2c         [   ]    |       `-- i2c@30a40000
 simple_bus  [   ]    `-- regulators
 => i2c dev 0
 Setting bus to 0
 => i2c probe
 Valid chip addresses: 08 50
 => i2c md 8 31
 0031: 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
arch/arm/imx-common/i2c-mxv7.c
arch/arm/include/asm/imx-common/mxc_i2c.h
drivers/i2c/mxc_i2c.c

index 1a632e7203269726744c7cccb53f0e29e351672f..f3a5c3f3262d56dbf9f7e749aa1d757d9d9bbd9b 100644 (file)
@@ -12,7 +12,7 @@
 #include <asm/imx-common/mxc_i2c.h>
 #include <watchdog.h>
 
-static int force_idle_bus(void *priv)
+int force_idle_bus(void *priv)
 {
        int i;
        int sda, scl;
@@ -99,8 +99,9 @@ int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
        if (ret)
                goto err_idle;
 
-       bus_i2c_init(i2c_bases[i2c_index], speed, slave_addr,
-                       force_idle_bus, p);
+#ifndef CONFIG_DM_I2C
+       bus_i2c_init(i2c_index, speed, slave_addr, force_idle_bus, p);
+#endif
 
        return 0;
 
index af861635350d00209405435084ef767bec5b77e6..355b25e8855dbc443ad02411c7fc2afa1d9a9541 100644 (file)
@@ -19,6 +19,36 @@ struct i2c_pads_info {
        struct i2c_pin_ctrl sda;
 };
 
+/*
+ * Information about i2c controller
+ * struct mxc_i2c_bus - information about the i2c[x] bus
+ * @index: i2c bus index
+ * @base: Address of I2C bus controller
+ * @driver_data: Flags for different platforms, such as I2C_QUIRK_FLAG.
+ * @speed: Speed of I2C bus
+ * @pads_info: pinctrl info for this i2c bus, will be used when pinctrl is ok.
+ * The following two is only to be compatible with non-DM part.
+ * @idle_bus_fn: function to force bus idle
+ * @idle_bus_data: parameter for idle_bus_fun
+ */
+struct mxc_i2c_bus {
+       /*
+        * board file can use this index to locate which i2c_pads_info is for
+        * i2c_idle_bus. When pinmux is implement, this entry can be
+        * discarded. Here we do not use dev->seq, because we do not want to
+        * export device to board file.
+        */
+       int index;
+       ulong base;
+       ulong driver_data;
+       int speed;
+       struct i2c_pads_info *pads_info;
+#ifndef CONFIG_DM_I2C
+       int (*idle_bus_fn)(void *p);
+       void *idle_bus_data;
+#endif
+};
+
 #if defined(CONFIG_MX6QDL)
 #define I2C_PADS(name, scl_i2c, scl_gpio, scl_gp, sda_i2c, sda_gpio, sda_gp) \
        struct i2c_pads_info mx6q_##name = {            \
@@ -54,10 +84,8 @@ struct i2c_pads_info {
 
 int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
              struct i2c_pads_info *p);
-void bus_i2c_init(void *base, int speed, int slave_addr,
+void bus_i2c_init(int index, int speed, int slave_addr,
                int (*idle_bus_fn)(void *p), void *p);
-int bus_i2c_read(void *base, uchar chip, uint addr, int alen, uchar *buf,
-               int len);
-int bus_i2c_write(void *base, uchar chip, uint addr, int alen,
-               const uchar *buf, int len);
+int force_idle_bus(void *priv);
+int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus);
 #endif
index 42782cb1ace611779cd745ee3077af0165ed1d09..81adf6f450329d38ed6179f71d2dc92460accec3 100644 (file)
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
 #include <asm/errno.h>
+#include <asm/imx-common/mxc_i2c.h>
 #include <asm/io.h>
 #include <i2c.h>
 #include <watchdog.h>
+#include <dm.h>
+#include <fdtdec.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#ifdef I2C_QUIRK_REG
-struct mxc_i2c_regs {
-       uint8_t         iadr;
-       uint8_t         ifdr;
-       uint8_t         i2cr;
-       uint8_t         i2sr;
-       uint8_t         i2dr;
-};
-#else
-struct mxc_i2c_regs {
-       uint32_t        iadr;
-       uint32_t        ifdr;
-       uint32_t        i2cr;
-       uint32_t        i2sr;
-       uint32_t        i2dr;
-};
-#endif
+#define I2C_QUIRK_FLAG         (1 << 0)
+
+#define IMX_I2C_REGSHIFT       2
+#define VF610_I2C_REGSHIFT     0
+/* Register index */
+#define IADR   0
+#define IFDR   1
+#define I2CR   2
+#define I2SR   3
+#define I2DR   4
 
 #define I2CR_IIEN      (1 << 6)
 #define I2CR_MSTA      (1 << 5)
@@ -104,7 +100,6 @@ static u16 i2c_clk_div[50][2] = {
 };
 #endif
 
-
 #ifndef CONFIG_SYS_MXC_I2C1_SPEED
 #define CONFIG_SYS_MXC_I2C1_SPEED 100000
 #endif
@@ -131,11 +126,10 @@ static u16 i2c_clk_div[50][2] = {
 #define CONFIG_SYS_MXC_I2C4_SLAVE 0
 #endif
 
-
 /*
  * Calculate and set proper clock divider
  */
-static uint8_t i2c_imx_get_clk(unsigned int rate)
+static uint8_t i2c_imx_get_clk(struct mxc_i2c_bus *i2c_bus, unsigned int rate)
 {
        unsigned int i2c_clk_rate;
        unsigned int div;
@@ -168,18 +162,20 @@ static uint8_t i2c_imx_get_clk(unsigned int rate)
 /*
  * Set I2C Bus speed
  */
-static int bus_i2c_set_bus_speed(void *base, int speed)
+static int bus_i2c_set_bus_speed(struct mxc_i2c_bus *i2c_bus, int speed)
 {
-       struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base;
-       u8 clk_idx = i2c_imx_get_clk(speed);
+       ulong base = i2c_bus->base;
+       bool quirk = i2c_bus->driver_data & I2C_QUIRK_FLAG ? true : false;
+       u8 clk_idx = i2c_imx_get_clk(i2c_bus, speed);
        u8 idx = i2c_clk_div[clk_idx][1];
+       int reg_shift = quirk ? VF610_I2C_REGSHIFT : IMX_I2C_REGSHIFT;
 
        /* Store divider value */
-       writeb(idx, &i2c_regs->ifdr);
+       writeb(idx, base + (IFDR << reg_shift));
 
        /* Reset module */
-       writeb(I2CR_IDIS, &i2c_regs->i2cr);
-       writeb(0, &i2c_regs->i2sr);
+       writeb(I2CR_IDIS, base + (I2CR << reg_shift));
+       writeb(0, base + (I2SR << reg_shift));
        return 0;
 }
 
@@ -187,21 +183,26 @@ static int bus_i2c_set_bus_speed(void *base, int speed)
 #define ST_BUS_BUSY (I2SR_IBB | (I2SR_IBB << 8))
 #define ST_IIF (I2SR_IIF | (I2SR_IIF << 8))
 
-static int wait_for_sr_state(struct mxc_i2c_regs *i2c_regs, unsigned state)
+static int wait_for_sr_state(struct mxc_i2c_bus *i2c_bus, unsigned state)
 {
        unsigned sr;
        ulong elapsed;
+       bool quirk = i2c_bus->driver_data & I2C_QUIRK_FLAG ? true : false;
+       int reg_shift = quirk ? VF610_I2C_REGSHIFT : IMX_I2C_REGSHIFT;
+       ulong base = i2c_bus->base;
        ulong start_time = get_timer(0);
        for (;;) {
-               sr = readb(&i2c_regs->i2sr);
+               sr = readb(base + (I2SR << reg_shift));
                if (sr & I2SR_IAL) {
-#ifdef I2C_QUIRK_REG
-                       writeb(sr | I2SR_IAL, &i2c_regs->i2sr);
-#else
-                       writeb(sr & ~I2SR_IAL, &i2c_regs->i2sr);
-#endif
+                       if (quirk)
+                               writeb(sr | I2SR_IAL, base +
+                                      (I2SR << reg_shift));
+                       else
+                               writeb(sr & ~I2SR_IAL, base +
+                                      (I2SR << reg_shift));
                        printf("%s: Arbitration lost sr=%x cr=%x state=%x\n",
-                               __func__, sr, readb(&i2c_regs->i2cr), state);
+                               __func__, sr, readb(base + (I2CR << reg_shift)),
+                               state);
                        return -ERESTART;
                }
                if ((sr & (state >> 8)) == (unsigned char)state)
@@ -212,17 +213,21 @@ static int wait_for_sr_state(struct mxc_i2c_regs *i2c_regs, unsigned state)
                        break;
        }
        printf("%s: failed sr=%x cr=%x state=%x\n", __func__,
-                       sr, readb(&i2c_regs->i2cr), state);
+              sr, readb(base + (I2CR << reg_shift)), state);
        return -ETIMEDOUT;
 }
 
-static int tx_byte(struct mxc_i2c_regs *i2c_regs, u8 byte)
+static int tx_byte(struct mxc_i2c_bus *i2c_bus, u8 byte)
 {
        int ret;
+       int reg_shift = i2c_bus->driver_data & I2C_QUIRK_FLAG ?
+                       VF610_I2C_REGSHIFT : IMX_I2C_REGSHIFT;
+       ulong base = i2c_bus->base;
 
-       writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr);
-       writeb(byte, &i2c_regs->i2dr);
-       ret = wait_for_sr_state(i2c_regs, ST_IIF);
+       writeb(I2SR_IIF_CLEAR, base + (I2SR << reg_shift));
+       writeb(byte, base + (I2DR << reg_shift));
+
+       ret = wait_for_sr_state(i2c_bus, ST_IIF);
        if (ret < 0)
                return ret;
        if (ret & I2SR_RX_NO_AK)
@@ -230,17 +235,29 @@ static int tx_byte(struct mxc_i2c_regs *i2c_regs, u8 byte)
        return 0;
 }
 
+/*
+ * Stub implementations for outer i2c slave operations.
+ */
+void __i2c_force_reset_slave(void)
+{
+}
+void i2c_force_reset_slave(void)
+       __attribute__((weak, alias("__i2c_force_reset_slave")));
+
 /*
  * Stop I2C transaction
  */
-static void i2c_imx_stop(struct mxc_i2c_regs *i2c_regs)
+static void i2c_imx_stop(struct mxc_i2c_bus *i2c_bus)
 {
        int ret;
-       unsigned int temp = readb(&i2c_regs->i2cr);
+       int reg_shift = i2c_bus->driver_data & I2C_QUIRK_FLAG ?
+                       VF610_I2C_REGSHIFT : IMX_I2C_REGSHIFT;
+       ulong base = i2c_bus->base;
+       unsigned int temp = readb(base + (I2CR << reg_shift));
 
        temp &= ~(I2CR_MSTA | I2CR_MTX);
-       writeb(temp, &i2c_regs->i2cr);
-       ret = wait_for_sr_state(i2c_regs, ST_BUS_IDLE);
+       writeb(temp, base + (I2CR << reg_shift));
+       ret = wait_for_sr_state(i2c_bus, ST_BUS_IDLE);
        if (ret < 0)
                printf("%s:trigger stop failed\n", __func__);
 }
@@ -249,66 +266,96 @@ static void i2c_imx_stop(struct mxc_i2c_regs *i2c_regs)
  * Send start signal, chip address and
  * write register address
  */
-static int i2c_init_transfer_(struct mxc_i2c_regs *i2c_regs,
-               uchar chip, uint addr, int alen)
+static int i2c_init_transfer_(struct mxc_i2c_bus *i2c_bus, u8 chip,
+                             u32 addr, int alen)
 {
        unsigned int temp;
        int ret;
+       bool quirk = i2c_bus->driver_data & I2C_QUIRK_FLAG ? true : false;
+       ulong base = i2c_bus->base;
+       int reg_shift = quirk ? VF610_I2C_REGSHIFT : IMX_I2C_REGSHIFT;
+
+       /* Reset i2c slave */
+       i2c_force_reset_slave();
 
        /* Enable I2C controller */
-#ifdef I2C_QUIRK_REG
-       if (readb(&i2c_regs->i2cr) & I2CR_IDIS) {
-#else
-       if (!(readb(&i2c_regs->i2cr) & I2CR_IEN)) {
-#endif
-               writeb(I2CR_IEN, &i2c_regs->i2cr);
+       if (quirk)
+               ret = readb(base + (I2CR << reg_shift)) & I2CR_IDIS;
+       else
+               ret = !(readb(base + (I2CR << reg_shift)) & I2CR_IEN);
+
+       if (ret) {
+               writeb(I2CR_IEN, base + (I2CR << reg_shift));
                /* Wait for controller to be stable */
                udelay(50);
        }
-       if (readb(&i2c_regs->iadr) == (chip << 1))
-               writeb((chip << 1) ^ 2, &i2c_regs->iadr);
-       writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr);
-       ret = wait_for_sr_state(i2c_regs, ST_BUS_IDLE);
+
+       if (readb(base + (IADR << reg_shift)) == (chip << 1))
+               writeb((chip << 1) ^ 2, base + (IADR << reg_shift));
+       writeb(I2SR_IIF_CLEAR, base + (I2SR << reg_shift));
+       ret = wait_for_sr_state(i2c_bus, ST_BUS_IDLE);
        if (ret < 0)
                return ret;
 
        /* Start I2C transaction */
-       temp = readb(&i2c_regs->i2cr);
+       temp = readb(base + (I2CR << reg_shift));
        temp |= I2CR_MSTA;
-       writeb(temp, &i2c_regs->i2cr);
+       writeb(temp, base + (I2CR << reg_shift));
 
-       ret = wait_for_sr_state(i2c_regs, ST_BUS_BUSY);
+       ret = wait_for_sr_state(i2c_bus, ST_BUS_BUSY);
        if (ret < 0)
                return ret;
 
        temp |= I2CR_MTX | I2CR_TX_NO_AK;
-       writeb(temp, &i2c_regs->i2cr);
+       writeb(temp, base + (I2CR << reg_shift));
 
        /* write slave address */
-       ret = tx_byte(i2c_regs, chip << 1);
+       ret = tx_byte(i2c_bus, chip << 1);
        if (ret < 0)
                return ret;
 
        while (alen--) {
-               ret = tx_byte(i2c_regs, (addr >> (alen * 8)) & 0xff);
+               ret = tx_byte(i2c_bus, (addr >> (alen * 8)) & 0xff);
                if (ret < 0)
                        return ret;
        }
        return 0;
 }
 
-static int i2c_idle_bus(void *base);
+#ifndef CONFIG_DM_I2C
+int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus)
+{
+       if (i2c_bus && i2c_bus->idle_bus_fn)
+               return i2c_bus->idle_bus_fn(i2c_bus->idle_bus_data);
+       return 0;
+}
+#else
+/*
+ * Since pinmux is not supported, implement a weak function here.
+ * You can implement your i2c_bus_idle in board file. When pinctrl
+ * is supported, this can be removed.
+ */
+int __i2c_idle_bus(struct mxc_i2c_bus *i2c_bus)
+{
+       return 0;
+}
 
-static int i2c_init_transfer(struct mxc_i2c_regs *i2c_regs,
-               uchar chip, uint addr, int alen)
+int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus)
+       __attribute__((weak, alias("__i2c_idle_bus")));
+#endif
+
+static int i2c_init_transfer(struct mxc_i2c_bus *i2c_bus, u8 chip,
+                            u32 addr, int alen)
 {
        int retry;
        int ret;
+       int reg_shift = i2c_bus->driver_data & I2C_QUIRK_FLAG ?
+                       VF610_I2C_REGSHIFT : IMX_I2C_REGSHIFT;
        for (retry = 0; retry < 3; retry++) {
-               ret = i2c_init_transfer_(i2c_regs, chip, addr, alen);
+               ret = i2c_init_transfer_(i2c_bus, chip, addr, alen);
                if (ret >= 0)
                        return 0;
-               i2c_imx_stop(i2c_regs);
+               i2c_imx_stop(i2c_bus);
                if (ret == -ENODEV)
                        return ret;
 
@@ -316,54 +363,67 @@ static int i2c_init_transfer(struct mxc_i2c_regs *i2c_regs,
                                retry);
                if (ret != -ERESTART)
                        /* Disable controller */
-                       writeb(I2CR_IDIS, &i2c_regs->i2cr);
+                       writeb(I2CR_IDIS, i2c_bus->base + (I2CR << reg_shift));
                udelay(100);
-               if (i2c_idle_bus(i2c_regs) < 0)
+               if (i2c_idle_bus(i2c_bus) < 0)
                        break;
        }
-       printf("%s: give up i2c_regs=%p\n", __func__, i2c_regs);
+       printf("%s: give up i2c_regs=0x%lx\n", __func__, i2c_bus->base);
        return ret;
 }
 
-/*
- * Read data from I2C device
- */
-int bus_i2c_read(void *base, uchar chip, uint addr, int alen, uchar *buf,
-               int len)
+
+static int i2c_write_data(struct mxc_i2c_bus *i2c_bus, u8 chip, const u8 *buf,
+                         int len)
+{
+       int i, ret = 0;
+
+       debug("i2c_write_data: chip=0x%x, len=0x%x\n", chip, len);
+       debug("write_data: ");
+       /* use rc for counter */
+       for (i = 0; i < len; ++i)
+               debug(" 0x%02x", buf[i]);
+       debug("\n");
+
+       for (i = 0; i < len; i++) {
+               ret = tx_byte(i2c_bus, buf[i]);
+               if (ret < 0) {
+                       debug("i2c_write_data(): rc=%d\n", ret);
+                       break;
+               }
+       }
+
+       return ret;
+}
+
+static int i2c_read_data(struct mxc_i2c_bus *i2c_bus, uchar chip, uchar *buf,
+                        int len)
 {
        int ret;
        unsigned int temp;
        int i;
-       struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base;
-
-       ret = i2c_init_transfer(i2c_regs, chip, addr, alen);
-       if (ret < 0)
-               return ret;
+       int reg_shift = i2c_bus->driver_data & I2C_QUIRK_FLAG ?
+                       VF610_I2C_REGSHIFT : IMX_I2C_REGSHIFT;
+       ulong base = i2c_bus->base;
 
-       temp = readb(&i2c_regs->i2cr);
-       temp |= I2CR_RSTA;
-       writeb(temp, &i2c_regs->i2cr);
-
-       ret = tx_byte(i2c_regs, (chip << 1) | 1);
-       if (ret < 0) {
-               i2c_imx_stop(i2c_regs);
-               return ret;
-       }
+       debug("i2c_read_data: chip=0x%x, len=0x%x\n", chip, len);
 
        /* setup bus to read data */
-       temp = readb(&i2c_regs->i2cr);
+       temp = readb(base + (I2CR << reg_shift));
        temp &= ~(I2CR_MTX | I2CR_TX_NO_AK);
        if (len == 1)
                temp |= I2CR_TX_NO_AK;
-       writeb(temp, &i2c_regs->i2cr);
-       writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr);
-       readb(&i2c_regs->i2dr);         /* dummy read to clear ICF */
+       writeb(temp, base + (I2CR << reg_shift));
+       writeb(I2SR_IIF_CLEAR, base + (I2SR << reg_shift));
+       /* dummy read to clear ICF */
+       readb(base + (I2DR << reg_shift));
 
        /* read data */
        for (i = 0; i < len; i++) {
-               ret = wait_for_sr_state(i2c_regs, ST_IIF);
+               ret = wait_for_sr_state(i2c_bus, ST_IIF);
                if (ret < 0) {
-                       i2c_imx_stop(i2c_regs);
+                       debug("i2c_read_data(): ret=%d\n", ret);
+                       i2c_imx_stop(i2c_bus);
                        return ret;
                }
 
@@ -372,105 +432,111 @@ int bus_i2c_read(void *base, uchar chip, uint addr, int alen, uchar *buf,
                 * controller from generating another clock cycle
                 */
                if (i == (len - 1)) {
-                       i2c_imx_stop(i2c_regs);
+                       i2c_imx_stop(i2c_bus);
                } else if (i == (len - 2)) {
-                       temp = readb(&i2c_regs->i2cr);
+                       temp = readb(base + (I2CR << reg_shift));
                        temp |= I2CR_TX_NO_AK;
-                       writeb(temp, &i2c_regs->i2cr);
+                       writeb(temp, base + (I2CR << reg_shift));
                }
-               writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr);
-               buf[i] = readb(&i2c_regs->i2dr);
+               writeb(I2SR_IIF_CLEAR, base + (I2SR << reg_shift));
+               buf[i] = readb(base + (I2DR << reg_shift));
        }
-       i2c_imx_stop(i2c_regs);
+
+       /* reuse ret for counter*/
+       for (ret = 0; ret < len; ++ret)
+               debug(" 0x%02x", buf[ret]);
+       debug("\n");
+
+       i2c_imx_stop(i2c_bus);
        return 0;
 }
 
+#ifndef CONFIG_DM_I2C
 /*
- * Write data to I2C device
+ * Read data from I2C device
  */
-int bus_i2c_write(void *base, uchar chip, uint addr, int alen,
-               const uchar *buf, int len)
+static int bus_i2c_read(struct mxc_i2c_bus *i2c_bus, u8 chip, u32 addr,
+                       int alen, u8 *buf, int len)
 {
-       int ret;
-       int i;
-       struct mxc_i2c_regs *i2c_regs = (struct mxc_i2c_regs *)base;
+       int ret = 0;
+       u32 temp;
+       int reg_shift = i2c_bus->driver_data & I2C_QUIRK_FLAG ?
+               VF610_I2C_REGSHIFT : IMX_I2C_REGSHIFT;
+       ulong base = i2c_bus->base;
 
-       ret = i2c_init_transfer(i2c_regs, chip, addr, alen);
+       ret = i2c_init_transfer(i2c_bus, chip, addr, alen);
        if (ret < 0)
                return ret;
 
-       for (i = 0; i < len; i++) {
-               ret = tx_byte(i2c_regs, buf[i]);
-               if (ret < 0)
-                       break;
+       temp = readb(base + (I2CR << reg_shift));
+       temp |= I2CR_RSTA;
+       writeb(temp, base + (I2CR << reg_shift));
+
+       ret = tx_byte(i2c_bus, (chip << 1) | 1);
+       if (ret < 0) {
+               i2c_imx_stop(i2c_bus);
+               return ret;
        }
-       i2c_imx_stop(i2c_regs);
+
+       ret = i2c_read_data(i2c_bus, chip, buf, len);
+
+       i2c_imx_stop(i2c_bus);
+       return ret;
+}
+
+/*
+ * Write data to I2C device
+ */
+static int bus_i2c_write(struct mxc_i2c_bus *i2c_bus, u8 chip, u32 addr,
+                        int alen, const u8 *buf, int len)
+{
+       int ret = 0;
+
+       ret = i2c_init_transfer(i2c_bus, chip, addr, alen);
+       if (ret < 0)
+               return ret;
+
+       ret = i2c_write_data(i2c_bus, chip, buf, len);
+
+       i2c_imx_stop(i2c_bus);
+
        return ret;
 }
 
-static void * const i2c_bases[] = {
+static struct mxc_i2c_bus mxc_i2c_buses[] = {
 #if defined(CONFIG_MX25)
-       (void *)IMX_I2C_BASE,
-       (void *)IMX_I2C2_BASE,
-       (void *)IMX_I2C3_BASE
+       { 0, IMX_I2C_BASE },
+       { 1, IMX_I2C2_BASE },
+       { 2, IMX_I2C3_BASE },
 #elif defined(CONFIG_MX27)
-       (void *)IMX_I2C1_BASE,
-       (void *)IMX_I2C2_BASE
+       { 0, IMX_I2C1_BASE },
+       { 1, IMX_I2C2_BASE },
 #elif defined(CONFIG_MX31) || defined(CONFIG_MX35) || \
        defined(CONFIG_MX51) || defined(CONFIG_MX53) || \
-       defined(CONFIG_MX6) || defined(CONFIG_LS102XA)
-       (void *)I2C1_BASE_ADDR,
-       (void *)I2C2_BASE_ADDR,
-       (void *)I2C3_BASE_ADDR
+       defined(CONFIG_MX6)
+       { 0, I2C1_BASE_ADDR },
+       { 1, I2C2_BASE_ADDR },
+       { 2, I2C3_BASE_ADDR },
+#elif defined(CONFIG_LS102XA)
+       { 0, I2C1_BASE_ADDR, I2C_QUIRK_FLAG },
+       { 1, I2C2_BASE_ADDR, I2C_QUIRK_FLAG },
+       { 2, I2C3_BASE_ADDR, I2C_QUIRK_FLAG },
 #elif defined(CONFIG_VF610)
-       (void *)I2C0_BASE_ADDR
+       { 0, I2C0_BASE_ADDR, I2C_QUIRK_FLAG },
 #elif defined(CONFIG_FSL_LSCH3)
-       (void *)I2C1_BASE_ADDR,
-       (void *)I2C2_BASE_ADDR,
-       (void *)I2C3_BASE_ADDR,
-       (void *)I2C4_BASE_ADDR
+       { 0, I2C1_BASE_ADDR, I2C_QUIRK_FLAG },
+       { 1, I2C2_BASE_ADDR, I2C_QUIRK_FLAG },
+       { 2, I2C3_BASE_ADDR, I2C_QUIRK_FLAG },
+       { 3, I2C4_BASE_ADDR, I2C_QUIRK_FLAG },
 #else
 #error "architecture not supported"
 #endif
+       { }
 };
 
-struct i2c_parms {
-       void *base;
-       void *idle_bus_data;
-       int (*idle_bus_fn)(void *p);
-};
-
-struct sram_data {
-       unsigned curr_i2c_bus;
-       struct i2c_parms i2c_data[ARRAY_SIZE(i2c_bases)];
-};
-
-void *i2c_get_base(struct i2c_adapter *adap)
-{
-       return i2c_bases[adap->hwadapnr];
-}
-
-static struct i2c_parms *i2c_get_parms(void *base)
-{
-       struct sram_data *srdata = (void *)gd->srdata;
-       int i = 0;
-       struct i2c_parms *p = srdata->i2c_data;
-       while (i < ARRAY_SIZE(srdata->i2c_data)) {
-               if (p->base == base)
-                       return p;
-               p++;
-               i++;
-       }
-       printf("Invalid I2C base: %p\n", base);
-       return NULL;
-}
-
-static int i2c_idle_bus(void *base)
+struct mxc_i2c_bus *i2c_get_base(struct i2c_adapter *adap)
 {
-       struct i2c_parms *p = i2c_get_parms(base);
-       if (p && p->idle_bus_fn)
-               return p->idle_bus_fn(p->idle_bus_data);
-       return 0;
+       return &mxc_i2c_buses[adap->hwadapnr];
 }
 
 static int mxc_i2c_read(struct i2c_adapter *adap, uint8_t chip,
@@ -495,29 +561,33 @@ static int mxc_i2c_probe(struct i2c_adapter *adap, uint8_t chip)
        return bus_i2c_write(i2c_get_base(adap), chip, 0, 0, NULL, 0);
 }
 
-void bus_i2c_init(void *base, int speed, int unused,
-               int (*idle_bus_fn)(void *p), void *idle_bus_data)
+int __enable_i2c_clk(unsigned char enable, unsigned i2c_num)
+{
+       return 1;
+}
+int enable_i2c_clk(unsigned char enable, unsigned i2c_num)
+       __attribute__((weak, alias("__enable_i2c_clk")));
+
+void bus_i2c_init(int index, int speed, int unused,
+                 int (*idle_bus_fn)(void *p), void *idle_bus_data)
 {
-       struct sram_data *srdata = (void *)gd->srdata;
-       int i = 0;
-       struct i2c_parms *p = srdata->i2c_data;
-       if (!base)
+       int ret;
+
+       if (index >= ARRAY_SIZE(mxc_i2c_buses)) {
+               debug("Error i2c index\n");
                return;
-       for (;;) {
-               if (!p->base || (p->base == base)) {
-                       p->base = base;
-                       if (idle_bus_fn) {
-                               p->idle_bus_fn = idle_bus_fn;
-                               p->idle_bus_data = idle_bus_data;
-                       }
-                       break;
-               }
-               p++;
-               i++;
-               if (i >= ARRAY_SIZE(srdata->i2c_data))
-                       return;
        }
-       bus_i2c_set_bus_speed(base, speed);
+
+       mxc_i2c_buses[index].idle_bus_fn = idle_bus_fn;
+       mxc_i2c_buses[index].idle_bus_data = idle_bus_data;
+
+       ret = enable_i2c_clk(1, index);
+       if (ret < 0) {
+               debug("I2C-%d clk fail to enable.\n", index);
+               return;
+       }
+
+       bus_i2c_set_bus_speed(&mxc_i2c_buses[index], speed);
 }
 
 /*
@@ -525,13 +595,13 @@ void bus_i2c_init(void *base, int speed, int unused,
  */
 static void mxc_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
 {
-       bus_i2c_init(i2c_get_base(adap), speed, slaveaddr, NULL, NULL);
+       bus_i2c_init(adap->hwadapnr, speed, slaveaddr, NULL, NULL);
 }
 
 /*
  * Set I2C Speed
  */
-static uint mxc_i2c_set_bus_speed(struct i2c_adapter *adap, uint speed)
+static u32 mxc_i2c_set_bus_speed(struct i2c_adapter *adap, uint speed)
 {
        return bus_i2c_set_bus_speed(i2c_get_base(adap), speed);
 }
@@ -556,6 +626,7 @@ U_BOOT_I2C_ADAP_COMPLETE(mxc2, mxc_i2c_init, mxc_i2c_probe,
                         CONFIG_SYS_MXC_I2C3_SPEED,
                         CONFIG_SYS_MXC_I2C3_SLAVE, 2)
 #endif
+
 #ifdef CONFIG_SYS_I2C_MXC_I2C4
 U_BOOT_I2C_ADAP_COMPLETE(mxc3, mxc_i2c_init, mxc_i2c_probe,
                         mxc_i2c_read, mxc_i2c_write,
@@ -563,3 +634,143 @@ U_BOOT_I2C_ADAP_COMPLETE(mxc3, mxc_i2c_init, mxc_i2c_probe,
                         CONFIG_SYS_MXC_I2C4_SPEED,
                         CONFIG_SYS_MXC_I2C4_SLAVE, 3)
 #endif
+
+#else
+
+static int mxc_i2c_set_bus_speed(struct udevice *bus, unsigned int speed)
+{
+       struct mxc_i2c_bus *i2c_bus = dev_get_priv(bus);
+
+       return bus_i2c_set_bus_speed(i2c_bus, speed);
+}
+
+static int mxc_i2c_probe(struct udevice *bus)
+{
+       struct mxc_i2c_bus *i2c_bus = dev_get_priv(bus);
+       fdt_addr_t addr;
+       int ret;
+
+       i2c_bus->driver_data = dev_get_driver_data(bus);
+
+       addr = dev_get_addr(bus);
+       if (addr == FDT_ADDR_T_NONE)
+               return -ENODEV;
+
+       i2c_bus->base = addr;
+       i2c_bus->index = bus->seq;
+
+       /* Enable clk */
+       ret = enable_i2c_clk(1, bus->seq);
+       if (ret < 0)
+               return ret;
+
+       ret = i2c_idle_bus(i2c_bus);
+       if (ret < 0) {
+               /* Disable clk */
+               enable_i2c_clk(0, bus->seq);
+               return ret;
+       }
+
+       /*
+        * Pinmux settings are in board file now, until pinmux is supported,
+        * we can set pinmux here in probe function.
+        */
+
+       debug("i2c : controller bus %d at %lu , speed %d: ",
+             bus->seq, i2c_bus->base,
+             i2c_bus->speed);
+
+       return 0;
+}
+
+static int mxc_i2c_probe_chip(struct udevice *bus, u32 chip_addr,
+                             u32 chip_flags)
+{
+       int ret;
+       struct mxc_i2c_bus *i2c_bus = dev_get_priv(bus);
+
+       ret = i2c_init_transfer(i2c_bus, chip_addr, 0, 0);
+       if (ret < 0) {
+               debug("%s failed, ret = %d\n", __func__, ret);
+               return ret;
+       }
+
+       i2c_imx_stop(i2c_bus);
+
+       return 0;
+}
+
+static int mxc_i2c_xfer(struct udevice *bus, struct i2c_msg *msg, int nmsgs)
+{
+       struct mxc_i2c_bus *i2c_bus = dev_get_priv(bus);
+       int ret = 0;
+       ulong base = i2c_bus->base;
+       int reg_shift = i2c_bus->driver_data & I2C_QUIRK_FLAG ?
+               VF610_I2C_REGSHIFT : IMX_I2C_REGSHIFT;
+
+       /*
+        * Here the 3rd parameter addr and the 4th one alen are set to 0,
+        * because here we only want to send out chip address. The register
+        * address is wrapped in msg.
+        */
+       ret = i2c_init_transfer(i2c_bus, msg->addr, 0, 0);
+       if (ret < 0) {
+               debug("i2c_init_transfer error: %d\n", ret);
+               return ret;
+       }
+
+       for (; nmsgs > 0; nmsgs--, msg++) {
+               bool next_is_read = nmsgs > 1 && (msg[1].flags & I2C_M_RD);
+               debug("i2c_xfer: chip=0x%x, len=0x%x\n", msg->addr, msg->len);
+               if (msg->flags & I2C_M_RD)
+                       ret = i2c_read_data(i2c_bus, msg->addr, msg->buf,
+                                           msg->len);
+               else {
+                       ret = i2c_write_data(i2c_bus, msg->addr, msg->buf,
+                                            msg->len);
+                       if (ret)
+                               break;
+                       if (next_is_read) {
+                               /* Reuse ret */
+                               ret = readb(base + (I2CR << reg_shift));
+                               ret |= I2CR_RSTA;
+                               writeb(ret, base + (I2CR << reg_shift));
+
+                               ret = tx_byte(i2c_bus, (msg->addr << 1) | 1);
+                               if (ret < 0) {
+                                       i2c_imx_stop(i2c_bus);
+                                       break;
+                               }
+                       }
+               }
+       }
+
+       if (ret)
+               debug("i2c_write: error sending\n");
+
+       i2c_imx_stop(i2c_bus);
+
+       return ret;
+}
+
+static const struct dm_i2c_ops mxc_i2c_ops = {
+       .xfer           = mxc_i2c_xfer,
+       .probe_chip     = mxc_i2c_probe_chip,
+       .set_bus_speed  = mxc_i2c_set_bus_speed,
+};
+
+static const struct udevice_id mxc_i2c_ids[] = {
+       { .compatible = "fsl,imx21-i2c", },
+       { .compatible = "fsl,vf610-i2c", .data = I2C_QUIRK_FLAG, },
+       {}
+};
+
+U_BOOT_DRIVER(i2c_mxc) = {
+       .name = "i2c_mxc",
+       .id = UCLASS_I2C,
+       .of_match = mxc_i2c_ids,
+       .probe = mxc_i2c_probe,
+       .priv_auto_alloc_size = sizeof(struct mxc_i2c_bus),
+       .ops = &mxc_i2c_ops,
+};
+#endif