From: Marek Vasut Date: Mon, 21 Oct 2024 19:34:57 +0000 (+0200) Subject: ARM: dts: stm32: Drop remnants of upstream DT switch on DH STM32 DHSOM X-Git-Url: http://git.dujemihanovic.xyz/html/%7B%7B%20.Permalink%20%7D%7D?a=commitdiff_plain;h=635e9483c823c50bbf71500088313f68568f3324;p=u-boot.git ARM: dts: stm32: Drop remnants of upstream DT switch on DH STM32 DHSOM Remove unused local DT copies after the OF_UPSTREAM conversion. Fixes: cccb29fc1270 ("ARM: dts: stm32: Switch to using upstream DT on DH STM32 DHSOM") Reported-by: Patrick Delaunay Signed-off-by: Marek Vasut Reviewed-by: Patrick Delaunay --- diff --git a/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi b/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi deleted file mode 100644 index ddad649777..0000000000 --- a/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi +++ /dev/null @@ -1,308 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) -/* - * Copyright (C) 2024 Marek Vasut - */ - -#include -#include -#include -#include -#include -#include "stm32mp13-pinctrl.dtsi" - -/ { - model = "DH electronics STM32MP13xx DHCOR SoM"; - compatible = "dh,stm32mp131a-dhcor-som", - "st,stm32mp131"; - - aliases { - mmc0 = &sdmmc2; - mmc1 = &sdmmc1; - serial0 = &uart4; - serial1 = &uart7; - rtc0 = &rv3032; - spi0 = &qspi; - }; - - memory@c0000000 { - device_type = "memory"; - reg = <0xc0000000 0x20000000>; - }; - - reserved-memory { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - optee@dd000000 { - reg = <0xdd000000 0x3000000>; - no-map; - }; - }; - - sdio_pwrseq: sdio-pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&gpiof 12 GPIO_ACTIVE_LOW>; - }; - - vin: vin { - compatible = "regulator-fixed"; - regulator-name = "vin"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - }; -}; - -&i2c3 { - i2c-scl-rising-time-ns = <96>; - i2c-scl-falling-time-ns = <3>; - clock-frequency = <400000>; - status = "okay"; - /* spare dmas for other usage */ - /delete-property/dmas; - /delete-property/dma-names; - - pmic: stpmic@33 { - compatible = "st,stpmic1"; - reg = <0x33>; - interrupts-extended = <&gpioi 3 IRQ_TYPE_EDGE_FALLING>; - interrupt-controller; - #interrupt-cells = <2>; - status = "okay"; - - regulators { - compatible = "st,stpmic1-regulators"; - - ldo1-supply = <&vin>; - ldo2-supply = <&vin>; - ldo3-supply = <&vin>; - ldo4-supply = <&vin>; - ldo5-supply = <&vin>; - ldo6-supply = <&vin>; - pwr_sw1-supply = <&bst_out>; - pwr_sw2-supply = <&bst_out>; - - vddcpu: buck1 { /* VDD_CPU_1V2 */ - regulator-name = "vddcpu"; - regulator-min-microvolt = <1250000>; - regulator-max-microvolt = <1250000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vdd_ddr: buck2 { /* VDD_DDR_1V35 */ - regulator-name = "vdd_ddr"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vdd: buck3 { /* VDD_3V3_1V8 */ - regulator-name = "vdd"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vddcore: buck4 { /* VDD_CORE_1V2 */ - regulator-name = "vddcore"; - regulator-min-microvolt = <1250000>; - regulator-max-microvolt = <1250000>; - regulator-always-on; - regulator-initial-mode = <0>; - regulator-over-current-protection; - }; - - vdd_adc: ldo1 { /* VDD_ADC_1V8 */ - regulator-name = "vdd_adc"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - interrupts = ; - }; - - vdd_ldo2: ldo2 { /* LDO2_OUT_1V8 */ - regulator-name = "vdd_ldo2"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - interrupts = ; - }; - - vdd_ldo3: ldo3 { /* LDO3_OUT */ - regulator-name = "vdd_ldo3"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - interrupts = ; - }; - - vdd_usb: ldo4 { /* VDD_USB_3V3 */ - regulator-name = "vdd_usb"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - interrupts = ; - }; - - vdd_sd: ldo5 { /* VDD_SD_3V3_1V8 */ - regulator-name = "vdd_sd"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - interrupts = ; - }; - - vdd_sd2: ldo6 { /* VDD_SD2_3V3_1V8 */ - regulator-name = "vdd_sd2"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - interrupts = ; - }; - - vref_ddr: vref_ddr { /* VREF_DDR_0V675 */ - regulator-name = "vref_ddr"; - regulator-always-on; - }; - - bst_out: boost { /* BST_OUT_5V2 */ - regulator-name = "bst_out"; - }; - - vbus_otg: pwr_sw1 { - regulator-name = "vbus_otg"; - interrupts = ; - }; - - vbus_sw: pwr_sw2 { - regulator-name = "vbus_sw"; - interrupts = ; - regulator-active-discharge = <1>; - }; - }; - - onkey { - compatible = "st,stpmic1-onkey"; - interrupts = , ; - interrupt-names = "onkey-falling", "onkey-rising"; - status = "okay"; - }; - - watchdog { - compatible = "st,stpmic1-wdt"; - status = "disabled"; - }; - }; - - eeprom0: eeprom@50 { - compatible = "atmel,24c256"; /* ST M24256 */ - reg = <0x50>; - pagesize = <64>; - }; - - rv3032: rtc@51 { - compatible = "microcrystal,rv3032"; - reg = <0x51>; - interrupts-extended = <&gpioi 0 IRQ_TYPE_EDGE_FALLING>; - }; -}; - -&iwdg2 { - timeout-sec = <32>; - status = "okay"; -}; - -&qspi { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qspi_clk_pins_a - &qspi_bk1_pins_a - &qspi_cs1_pins_a>; - pinctrl-1 = <&qspi_clk_sleep_pins_a - &qspi_bk1_sleep_pins_a - &qspi_cs1_sleep_pins_a>; - #address-cells = <1>; - #size-cells = <0>; - status = "okay"; - - flash0: flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-rx-bus-width = <4>; - spi-max-frequency = <108000000>; - #address-cells = <1>; - #size-cells = <1>; - }; -}; - -/* Console UART */ -&uart4 { - pinctrl-names = "default", "sleep", "idle"; - pinctrl-0 = <&uart4_pins_b>; - pinctrl-1 = <&uart4_sleep_pins_b>; - pinctrl-2 = <&uart4_idle_pins_b>; - /delete-property/dmas; - /delete-property/dma-names; - status = "okay"; -}; - -/* Bluetooth */ -&uart7 { - pinctrl-names = "default", "sleep", "idle"; - pinctrl-0 = <&uart7_pins_a>; - pinctrl-1 = <&uart7_sleep_pins_a>; - pinctrl-2 = <&uart7_idle_pins_a>; - uart-has-rtscts; - status = "okay"; - - bluetooth { - compatible = "infineon,cyw43439-bt", "brcm,bcm4329-bt"; - max-speed = <3000000>; - device-wakeup-gpios = <&gpiog 9 GPIO_ACTIVE_HIGH>; - shutdown-gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>; - }; -}; - -/* SDIO WiFi */ -&sdmmc1 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>; - pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>; - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; - bus-width = <4>; - cap-power-off-card; - keep-power-in-suspend; - non-removable; - st,neg-edge; - vmmc-supply = <&vdd>; - mmc-pwrseq = <&sdio_pwrseq>; - status = "okay"; - - #address-cells = <1>; - #size-cells = <0>; - - brcmf: bcrmf@1 { /* muRata 1YN */ - reg = <1>; - compatible = "infineon,cyw43439-fmac", "brcm,bcm4329-fmac"; - interrupt-parent = <&gpioe>; - interrupts = <14 IRQ_TYPE_LEVEL_LOW>; - interrupt-names = "host-wake"; - }; -}; - -/* eMMC */ -&sdmmc2 { - pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>; - pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>; - pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>; - bus-width = <8>; - mmc-ddr-3_3v; - no-sd; - no-sdio; - non-removable; - st,neg-edge; - vmmc-supply = <&vdd>; - vqmmc-supply = <&vdd>; - status = "okay"; -}; diff --git a/arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts b/arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts deleted file mode 100644 index c8b9818499..0000000000 --- a/arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts +++ /dev/null @@ -1,30 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) -/* - * Copyright (C) 2022 Marek Vasut - * - * DHCOR STM32MP1 variant: - * DHCR-STM32MP153C-C065-R051-V33-SPI-I-01LG - * DHCOR PCB number: 586-100 or newer - * DRC Compact PCB number: 627-100 or newer - */ - -/dts-v1/; - -#include "stm32mp153.dtsi" -#include "stm32mp15xc.dtsi" -#include "stm32mp15xx-dhcor-som.dtsi" -#include "stm32mp15xx-dhcor-drc-compact.dtsi" - -/ { - model = "DH electronics STM32MP153C DHCOR DRC Compact"; - compatible = "dh,stm32mp153c-dhcor-drc-compact", - "dh,stm32mp153c-dhcor-som", - "st,stm32mp153"; -}; - -&m_can1 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&m_can1_pins_c>; - pinctrl-1 = <&m_can1_sleep_pins_c>; - status = "okay"; -}; diff --git a/arch/arm/dts/stm32mp157a-dhcor-avenger96.dts b/arch/arm/dts/stm32mp157a-dhcor-avenger96.dts deleted file mode 100644 index 2e3c9fbb4e..0000000000 --- a/arch/arm/dts/stm32mp157a-dhcor-avenger96.dts +++ /dev/null @@ -1,38 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) -/* - * Copyright (C) Linaro Ltd 2019 - All Rights Reserved - * Author: Manivannan Sadhasivam - * Copyright (C) 2020 Marek Vasut - * - * DHCOR STM32MP1 variant: - * DHCR-STM32MP157A-C065-R102-V18-SPI-C-01LG - * DHCOR PCB number: 586-100 or newer - * Avenger96 PCB number: 588-200 or newer - */ - -/dts-v1/; - -#include "stm32mp157.dtsi" -#include "stm32mp15xc.dtsi" -#include "stm32mp15xx-dhcor-som.dtsi" -#include "stm32mp15xx-dhcor-avenger96.dtsi" - -/ { - model = "Arrow Electronics STM32MP157A Avenger96 board"; - compatible = "arrow,stm32mp157a-avenger96", "dh,stm32mp157a-dhcor-som", - "st,stm32mp157"; -}; - -&m_can1 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&m_can1_pins_b>; - pinctrl-1 = <&m_can1_sleep_pins_b>; - status = "disabled"; -}; - -&m_can2 { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&m_can2_pins_a>; - pinctrl-1 = <&m_can2_sleep_pins_a>; - status = "disabled"; -};