The Qnap TS433 is a 4-bay NAS based around the RK3568.
Two SATA bays are connected to the RK3568's own SATA controllers while
the other two are connected to a JMicron SATA controller living on the
PCIe bus.
It provides one 2.5Gb and one 1Gb ethernet port as well as 3 usb ports.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2024 Heiko Stuebner <heiko@sntech.de>
+ */
+
+#include "rk356x-u-boot.dtsi"
help
Powkiddy X55 handheld gaming console with an RK3566 SoC.
+config TARGET_QNAP_TS433_RK3568
+ bool "QNAP-TS433"
+ help
+ Qnap TS433 4-bay NAS with a RK3568 SoC.
+
+ It provides the following featureset:
+ * 4GB LPDDR4
+ * 4GB eMMC
+ * 2 SATA ports connected to two RK3568's SATA controllers
+ * 2 SATA ports connected to a JMicron JMB58x AHCI SATA controller
+ * 1 1G network controller
+ * 1 2.5G Realtek RTL8125 network controller
+
config TARGET_QUARTZ64_RK3566
bool "Pine64 Quartz64"
help
source "board/hardkernel/odroid_m1s/Kconfig"
source "board/pine64/quartz64_rk3566/Kconfig"
source "board/powkiddy/x55/Kconfig"
+source "board/qnap/ts433/Kconfig"
source "board/radxa/zero3-rk3566/Kconfig"
source "board/xunlong/orangepi-3b-rk3566/Kconfig"
--- /dev/null
+if TARGET_QNAP_TS433_RK3568
+
+config SYS_BOARD
+ default "qnap_ts433"
+
+config SYS_VENDOR
+ default "qnap"
+
+config SYS_CONFIG_NAME
+ default "qnap_ts433"
+
+endif
--- /dev/null
+QNAP-TS433
+M: Heiko Stuebner <heiko@sntech.de>
+S: Maintained
+F: board/qnap/ts433/
+F: doc/board/qnap/
+F: include/configs/qnap_ts433.h
+F: configs/qnap-ts433-rk3568_defconfig
+F: arch/arm/dts/rk3568-qnap-ts433-u-boot.dtsi
--- /dev/null
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_SYS_HAS_NONCACHED_MEMORY=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_DEFAULT_DEVICE_TREE="rockchip/rk3568-qnap-ts433"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_SERIAL=y
+CONFIG_TARGET_QNAP_TS433_RK3568=y
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-qnap-ts433.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SATA=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_ROCKUSB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_AHCI_PCI=y
+CONFIG_DWC_AHCI=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_DWC_ETH_QOS=y
+CONFIG_DWC_ETH_QOS_ROCKCHIP=y
+CONFIG_RTL8169=y
+CONFIG_PCIE_DW_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_FAN53555=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
phytec/index
purism/index
qualcomm/index
+ qnap/index
renesas/index
rockchip/index
samsung/index
--- /dev/null
+.. SPDX-License-Identifier: GPL-2.0+
+
+Qnap
+====
+
+.. toctree::
+ :maxdepth: 2
+
+ ts433.rst
--- /dev/null
+.. SPDX-License-Identifier: GPL-2.0+
+
+U-Boot for Qnap TS433 Devices
+=================================
+
+This allows U-Boot to boot the Qnap TS433 NAS
+
+Preparing the serial
+--------------------
+
+Qnap devices run their serial console with a 115200 baudrate. As the
+binary DDR-init and maskrom-downloader expect a 1500000 rate, it is
+necessary to adapt the binaries if their output is needed.
+
+This can be done with a binary provided in the rkbin repository.
+First the ddrbin_param.txt in the rkbin repo needs to be modified:
+
+.. code-block:: bash
+
+ diff --git a/tools/ddrbin_param.txt b/tools/ddrbin_param.txt
+ index 0dfdd318..82ade7e7 100644
+ --- a/tools/ddrbin_param.txt
+ +++ b/tools/ddrbin_param.txt
+ @@ -11,7 +11,7 @@ lp5_freq=
+
+ uart id=
+ uart iomux=
+ -uart baudrate=
+ +uart baudrate=115200
+
+ sr_idle=
+ pd_idle=
+
+And after that the ddrbin_tool binary can be used to modify apply this
+modification and also a new maskrom downloader can be build:
+
+.. code-block:: bash
+
+ $ tools/ddrbin_tool rk3568 tools/ddrbin_param.txt bin/rk35/rk3568_ddr_1560MHz_v1.21.bin
+ $ tools/boot_merger RKBOOT/RK3568MINIALL.ini
+
+Building U-Boot
+---------------
+
+.. code-block:: bash
+
+ $ export CROSS_COMPILE=aarch64-linux-gnu-
+ $ export BL31=../rkbin/bin/rk35/rk3568_bl31_v1.34.elf
+ $ export ROCKCHIP_TPL=../rkbin/bin/rk35/rk3568_ddr_1056MHz_v1.13.bin
+ $ make qnap-ts433-rk3568_defconfig
+ $ make
+
+This will build ``u-boot-rockchip.bin`` which can be written to the
+on-board eMMC.
+
+Image installation
+------------------
+
+The Qnap thankfully provides an easily accessible serial header as well as
+a very user-friendly jumper-header to bring the device into maskrom mode.
+
+To access both, the drive trays need to be removed. Looking at the board,
+through the upper cutout of the metal frame the white 4-port serial-header
+can be seen next to a barcode sticker. It's pinout is as follows:
+
+.. code-block:: none
+
+ ,_ _.
+ |1234| 1=TX 2=VCC
+ `----' 3=RX 4=GND
+
+
+Directly below it, the mentioned 2-pin jumper header can be seen.
+
+To write your u-boot to the device, it needs to be powered off first. Then
+a jumper or suitable cable needs to be used to connect the two pins of the
+maskrom header. Turning on the device now will start it in maskrom mode.
+
+It is important that the jumper gets removed after that stop and before
+actually trying to write to the emmc.
+
+The front usb-port needs to be connected to the host with an USB-A-to-A
+cable to allow flashing.
+
+The flashing itself is done via rkdeveloptool, which can be found for
+example as package of that name in Debian-based distributions:
+
+.. code-block:: bash
+
+ $ rkdeveloptool db rk356x_spl_loader_v1.21.113.bin
+ $ rkdeveloptool wl 64 u-boot-rockchip.bin
- FriendlyElec NanoPi R5S (nanopi-r5s-rk3568)
- Generic RK3566/RK3568 (generic-rk3568)
- Hardkernel ODROID-M1 (odroid-m1-rk3568)
+ - QNAP TS-433 (qnap-ts433-rk3568)
- Radxa E25 Carrier Board (radxa-e25-rk3568)
- Radxa ROCK 3A (rock-3a-rk3568)
- Radxa ROCK 3B (rock-3b-rk3568)
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+
+#ifndef __QNAP_TS433_H
+#define __QNAP_TS433_H
+
+#define ROCKCHIP_DEVICE_SETTINGS
+
+#include <configs/rk3568_common.h>
+
+#endif
projects / u-boot.git / commitdiff