Dhruva Gole [Tue, 30 Jan 2024 15:00:00 +0000 (20:30 +0530)]
firmware: ti_sci: Add comment explaining the is_secure code
Add a comment to explain the code under is_secure condition of
ti_sci_do_xfer. This will help avoid confusion amongst people who may in
future touch upon this code.
Dhruva Gole [Tue, 30 Jan 2024 14:59:59 +0000 (20:29 +0530)]
firmware: ti_sci: fix the secure_hdr in do_xfer
The ti_sci driver in U-Boot has support for secure_msg as part of it's
do_xfer function. This let's U-boot send secure messages during boot up.
The protocol to send such secure messages is described as part of the
struct ti_sci_secure_msg_hdr. As part of this, there are 2 fields for
checksum and reserved that occupy the first 4 bytes of any secure
message. This is called as the secure_hdr.
As of now, the secure_hdr needs to be 0 init-ed before sending secure
messages. However the existing code was never putting the zero-inited vars
into the secure_buf, leading to possibility of the first 4 bytes of
secure_buf being possibly garbage.
Fix this by initialising the secure_hdr itself to the secure_buf
location, thus when we make secure_hdr members 0, it automatically ensures
the first 4 bytes of secure_buf are 0.
Fixes: 32cd25128bd849 ("firmware: Add basic support for TI System Control Interface (TI SCI)") Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Dhruva Gole <d-gole@ti.com>
arm: mach-k3: j721s2_init: Support less than max DDR controllers
The number of DDR controllers to be initialised and used should depend
on the device tree with the constraint of the maximum number of
controllers the device supports. Since J721S2 has multiple (2)
controllers, instead of hardcoding the number of probes, move to
depending on the device tree UCLASS_RAM nodes present.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com> Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
dma: ti: k3-udma: Use ring_idx to pair k3 nav rings
Use ring_idx to pair rings. ring_idx will be same as tx flow_id for all
non-negative flow_ids. For negative flow_ids, ring_idx will be tchan->id
added with bchan_cnt.
Brandon Maier [Mon, 22 Jan 2024 18:45:50 +0000 (18:45 +0000)]
scripts/gen_compile_commands: update to Linux v6.7
Adds support for assembly files and updates the LINE_PATTERN so it
supports both "cmd" and "savedcmd", which allows reverting the U-Boot
modification in commit 97fbb2eb016b ("scripts/gen_compile_commands.py:
adapt _LINE_PATTERN").
Upstream commits:
- 880946158b011 gen_compile_commands.py: fix path resolve with symlinks in it
- 9e56d3be4bfd2 gen_compile_commands: Sort output compile commands by file name
- 52c15e7e79285 gen_compile_commands: Allow the line prefix to still be cmd_
- 1c67921444bf6 gen_compile_commands: add assembly files to compilation database
Signed-off-by: Brandon Maier <brandon.maier@collins.com> Cc: Joao Marcos Costa <jmcosta944@gmail.com>
Tom Rini [Mon, 5 Feb 2024 18:33:01 +0000 (13:33 -0500)]
Merge patch series "board: siemens: clean up subfolders"
Enrico Leto <enrico.leto@siemens.com> says:
The common folder was initialially created for the common parts of
the products based on draco-am355x board family. We have the
product lines 'pxm2', 'rut' and the base line unfortunately named
'draco'! Adding the new capricorn-imx8 board family, the files
were enhanced without cleanup.
Simplify first EEPROM probe and access that implements both i2c
with & without driver model. Use abstraction functions for this.
Move all am355x specifics to a new file 'board_am335x'.
Enrico Leto [Wed, 24 Jan 2024 14:43:55 +0000 (15:43 +0100)]
siemens: factoryset: use correct config for soc specific implementation
Adding the capricorn board family some parts diverge from draco family.
The switches used were not pertinent and need to be enhanced for each new
board of the capricorn family. Replace them through the SOC name 'AM33XX'
and 'IMX8'.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Enrico Leto [Wed, 24 Jan 2024 14:43:53 +0000 (15:43 +0100)]
siemens: board: clean up products folders vs common
The common folder was initialially created for the common parts of the
products based on draco-am355x board family. These are the product lines
'pxm2', 'rut' and the base line named 'draco'!
Adding the new capricorn-imx8 board family, common was enhanced without
cleanup.
- rename 'common/board.c' to 'common/board_am335x.c'
- add 'common/board_am335x.h' for export to the product lines
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com> Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Tom Rini [Sat, 3 Feb 2024 14:11:25 +0000 (09:11 -0500)]
Merge tag 'smbios-2024-04-rc2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request smbios-2024-04-rc2
* In smbios command
- write 'Not Specified' for missing strings
- show correct table size for SMBIOS2.1 entry point
- adjust formatting of handle numbers
- add missing colon after UUID
* In generated SMBIOS table
- avoid introducing 'Unknown' string for missing properties
- provide RISC-V vendor ID in the type 4 structure
- provide the correct chassis handle in structure type 2
* Rename Structure Table Maximum Size field in SMBIOS 3 entry point
smbios: correctly name Structure Table Maximum Size field
In the SMBIOS 3 entry point the Structure Table Maximum Size field was
incorrectly named max_struct_size. A Maximum Structure Size field only
exists in the SMBIOS 2.1 entry point and has a different meaning.
Call the Structure Table Length field table_maximum_size.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Only the SMBIOS 2.1 entry point has a field for the maximum structure size.
As we have switched to an SMBIOS 3 entry point remove the superfluous
calculation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
cmd: smbios: show correct table size for SMBIOS2.1 entry point
The SMBIOS table size for SMBIOS2.1 entry points is in field 'Structure
Table Length' (offset 0x16) and not in field 'Maximum Structure Size'
(offset 0x08).
Rename the receiving variable max_struct_size to table_maximum_size
to avoid future confusion.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
smbios: if a string value is unknown, use string number 0
The SMBIOS specification describes: "If a string field references no string,
a null (0) is placed in that string field."
Accordingly we should avoid writing a string "Unknown" to the SMBIOS table.
dmidecode displays 'Not Specified' if the string number is 0.
Commit 00a871d34e2f ("smbios: empty strings in smbios_add_string()")
correctly identified that strings may not have length 0 as two
consecutive NULs indentify the end of the string list. But the suggested
solution did not match the intent of the SMBIOS specification.
Fixes: 00a871d34e2f ("smbios: empty strings in smbios_add_string()") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When no string is present in a table, next_ptr points to the same
location as eos. When calculating the string table length, we would only
reserve one \0. By spec a SMBIOS table has to end with two \0\0 when no
strings a present.
Signed-off-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add description for parameter sysinfo_id of function get_str_from_dt().
Fixes: 07c9e683a484 ("smbios: Allow a few values to come from sysinfo") Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
* Add RISC-V falcon mode documentation
* Add Clang build support
* Add cmd to detect Debug Trigger Extension support
* Add PWM setting for Unmatched board
* Add Milk-V Duo board support
* Add new device node and enable new config option for VisionFive2 board
* Add second virtio device for RISC-V QEMU
Kongyang Liu [Sun, 28 Jan 2024 07:05:24 +0000 (15:05 +0800)]
riscv: dts: sophgo: add basic device tree for Milk-V Duo board
Import device tree from Linux kernel to add basic support for CPU, PLIC,
UART and Timer. The name cv1800b in the filename represent the chip used
on Milk-V Duo board.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Aurelien Jarno [Sat, 27 Jan 2024 13:48:45 +0000 (14:48 +0100)]
configs: visionfive2: Disable ENV_IS_NOWHERE
The VisionFive 2 board supports saving the u-boot environment settings
are saved to on-board SPI flash. However the defconfig enables both
ENV_IS_NOWHERE and ENV_IS_IN_SPI_FLASH, preventing the "saveenv" command
to work. Fix that by disabling ENV_IS_NOWHERE.
Fixes: 7d79bed00c9e ("configs: starfive: Enable environment in SPI flash support") Reported-by: E Shattow <lucent@gmail.com> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Vincent Chen [Tue, 16 Jan 2024 06:35:57 +0000 (14:35 +0800)]
board: sifive: spl: Initialized the PWM setting in the SPL stage
LEDs and multiple fans can be controlled by SPL. This patch ensures
that all fans have been enabled in the SPL stage. In addition, the
LED's color will be set to yellow.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Co-developed-by: Nylon Chen <nylon.chen@sifive.com> Signed-off-by: Nylon Chen <nylon.chen@sifive.com> Co-developed-by: Zong Li <zong.li@sifve.com> Signed-off-by: Zong Li <zong.li@sifve.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Aurelien Jarno [Wed, 10 Jan 2024 20:26:53 +0000 (21:26 +0100)]
riscv: qemu: enable booting on a second virtio device
QEMU RISC-V supports multiple virtio devices, but only tries to boot to
the first one. Enable support for a second virtio device, that is useful
for instance to boot on a disk image + an installer. Ideally that should
be made dynamic, but that's a first step.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Aurelien Jarno [Wed, 10 Jan 2024 20:17:44 +0000 (21:17 +0100)]
board: starfive: handle compatible property in dynamic DT configuration
The difference between the StarFive VisionFive 2 1.2A and 1.3B boards is
handled dynamically by looking at the PCB version in the EEPROM in order
to have a single u-boot version for both versions of the board. While
the "model" property is correctly handled, the "compatible" one is
always the the one of version 1.3b.
This patch add support for dynamically configuring that property.
Fixes: 9b7060bd15e7 ("riscv: dts: jh7110: Combine the board device tree files of 1.2A and 1.3B") Signed-off-by: Aurelien Jarno <aurelien@aurel32.net> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Randolph [Fri, 29 Dec 2023 08:32:22 +0000 (16:32 +0800)]
spl: riscv: falcon: move fdt blob to specified address
In Falcon Boot mode, the fdt blob should be move to the RAM from
kernel BSS section. To avoid being cleared by BSS initialisation.
SPL_PAYLOAD_ARGS_ADDR is the address where SPL copies.
Signed-off-by: Randolph <randolph@andestech.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Ivan T. Ivanov [Tue, 23 Jan 2024 08:07:59 +0000 (10:07 +0200)]
configs: rpi_arm64: build position independent code
Latest RPi5 EEPROM firmware versions after "DATE: 2023/10/30", has changed
kernel load address from 0x80000 to 0x200000 which break boot process.
Switch to position independent code to be able to boot the same binary
on top of different EEPROM firmware versions.
Tested on:
Raspberry Pi 5 Model B Rev 1.0
Raspberry Pi 4 Model B Rev 1.1
Raspberry Pi 3 Model B Plus Rev 1.3
Raspberry Pi Zero 2 W Rev 1.0
Raspberry Pi 2 Model B Rev 1.2
Raspberry Pi Compute Module 4 Rev 1.0
Raspberry Pi Compute Module 3 Rev 1.0
Tested-by: Jens Maus <mail@jens-maus.de> Tested-by: Darko Alavanja <darko.alavanja@konsulko.com> Signed-off-by: Ivan T. Ivanov <iivanov@suse.de> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Ivan T. Ivanov [Tue, 23 Jan 2024 08:07:56 +0000 (10:07 +0200)]
bcm2835: Dynamically calculate bytes per pixel parameter
brcm,bcm2708-fb device provided by firmware on RPi5 uses
16 bits per pixel, so lets calculate framebuffer bytes
per pixel dynamically based on queried information.
Tested to work for RPi2b v1.2, RPi3b v1.3, RPi4b v1.1,
RPi2 Zero W, RPi5b v1.0.
Ivan T. Ivanov [Tue, 23 Jan 2024 08:07:55 +0000 (10:07 +0200)]
rpi5: Use devicetree to retrieve board revision
Firmware on RPi5 return error on board revision query
through firmware interface, but on the other hand it fills
"linux,revision" in "system" node, so use it to detect board
revision.
system {
linux,revision = <0xc04170>;
linux,serial = <0x6cf44e80 0x3c533ede>;
};
Dmitry Malkin [Tue, 23 Jan 2024 08:07:53 +0000 (10:07 +0200)]
rpi5: add initial memory map for bcm2712
This includes:
* 1GB of RAM (from 4GB or 8GB total)
* AXI ranges (main peripherals)
When HDMI cable is plugged in at boot time firmware will
insert "simple-framebuffer" device into devicetree and will
shrink first memory region to 0x3f800000UL. Board setup then
will properly reserve framebuffer region.
When no HDMI cable is plugged in the size of the region will
be 0x3fc00000UL.
Tom Rini [Tue, 30 Jan 2024 12:54:28 +0000 (07:54 -0500)]
Merge tag 'clk-2024.04-rc2' of https://source.denx.de/u-boot/custodians/u-boot-clk
Clock changes for v2024.04
This pull has the usual fixes and new (clock-adjacent) drivers. It also has some
cleanups for the clock API; in particular removing the unused rfree callback.
Svyatoslav Ryhel [Wed, 10 Jan 2024 16:09:56 +0000 (18:09 +0200)]
clk: clk-gpio: add actual gated clock
Existing gpio-gate-clock driver acts like a simple GPIO switch without any
effect on gated clock. Add actual clock actions into enable/disable ops and
implement get_rate op by passing gated clock if it is enabled.
Sean Anderson [Sat, 16 Dec 2023 19:38:43 +0000 (14:38 -0500)]
clk: Document clk_ops return codes and behavior
Currently, clock consumers cannot take any programmatic action based on the
return code of a clock function. This is because there is no
standardization, and generally no way of separating e.g. "there was a major
problem setting the rate for this clock" which usually should not be
recovered from, from "this clock doesn't support setting its rate" or "this
clock doesn't support *this* rate" which could be absolutely fine depending
on the driver.
This commit aims to standardize the acceptable codes which may be returned
from clock operations. In general,
- ENOSYS should be returned when an operation is not supported for a
particular clock.
- ENOENT may be returned if the clock ID is invalid. However, it is
encouraged to move any checks to request() to reduce code duplication.
- EINVAL should be returned for logical errors only (such as requesting an
invalid rate).
Each function has had specific guidance added for when to return each error
code. This is just guidance for now; most of the clock subsystem does not
yet conform to this standard. However, it is expected that new clock
drivers return these error codes.
Additionally, this commit adds expected behavior for each of the clock
operations. I believe these should be mostly straightforward and correspond
to existing behavior. I remember not understanding what the expected
invariants were for several clock functions, so hopefully this should help
out new driver authors. In the future, some of these invariants could be
checked via an optional config option.
Julien Masson [Fri, 15 Dec 2023 14:09:43 +0000 (15:09 +0100)]
clk: fix clk_get_rate() always return ulong
When we call clk_get_rate(), we expect to get clock rate value as
ulong.
In that case we should not use log_ret() macro since it use internally
an int.
Otherwise we may return an invalid/truncated clock rate value.
Signed-off-by: Julien Masson <jmasson@baylibre.com> Fixes: 5c5992cb90c ("clk: Add debugging for return values") Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Link: https://lore.kernel.org/r/87o7erv9p4.fsf@baylibre.com
Tom Rini [Mon, 29 Jan 2024 21:19:10 +0000 (16:19 -0500)]
Merge tag 'efi-2024-04-rc1-4' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2024-04-rc1-4
Documentation:
* uefi: remove ".py" suffix for pytest.py command
* correct date in migration plan for CONFIG_DM
UEFI:
* fix conflicting SPDX license in RISC-V EFI linker scripts
* page align EFI binary section in RISC-V EFI binaries
* separate .data and .text sections of RISC-V EFI binaries
* use common function to get EFI configuration table
Quentin Schulz [Tue, 23 Jan 2024 17:57:01 +0000 (18:57 +0100)]
tools: buildman: fix non-existing SafeConfigParser in Python 3.12+
SafeConfigParser was renamed back in Python 3.2 (yes, no typo) to
ConfigParser[1], but it was still working as an alias until it got
removed in 3.12[2].
Janne Grunau [Wed, 17 Jan 2024 22:27:34 +0000 (23:27 +0100)]
video: Support VIDEO_X2R10G10B10 in truetype console
Without explicit support for VIDEO_X2R10G10B10 VIDEO_X8R8G8B8 white
will be rendered as cyan-ish. The conversion leaves to lowest 2 bits
unset for more compact code.
Devarsh Thakkar [Wed, 24 Jan 2024 09:07:11 +0000 (14:37 +0530)]
video: tidss: Use DT property names for parsing nodes
Use device-tree node property names for parsing nodes instead of
indexing as indexing could be different between different SoCs based on
number of DSS entities available on that particular SoC.
Also correct the video layer naming in driver to match to actual one
being used in upstream DSS device-tree node [1].
This also fixes AM62x splash screen usage using the latest upstream DSS
device-tree nodes where hard-coded indexing which driver was using
before this patch was not matching the correct properties in the DT
node.
Fixes: 5f9f816bb8 ("drivers: video: tidss: TIDSS video driver support for AM62x") Signed-off-by: Devarsh Thakkar <devarsht@ti.com> Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Tom Rini [Mon, 29 Jan 2024 19:49:25 +0000 (14:49 -0500)]
Merge patch series "Move framebuffer reservation for SPL to RAM end"
Devarsh Thakkar <devarsht@ti.com> says:
Move video memory reservation for SPL at end of RAM so that it does
not interefere with reservations for next stage so that the next stage
need not have holes in between for passed regions and instead it can
maintain continuity in reservations.
Also catch the bloblist before starting reservations to avoid the same
problem.
While at it, also fill missing fields in video handoff struct before
passing it to next stage.
This is as per discussions at :
For moving SPL framebuffer reservation at end of RAM:
Devarsh Thakkar [Tue, 5 Dec 2023 15:55:21 +0000 (21:25 +0530)]
video: Fill video handoff in video post probe
Fill video handoff fields in video_post_probe as at this point we have
full framebuffer-related information.
Also fill all the fields available in video hand-off struct as those
were missing earlier and U-boot framework expects them to be filled for
some of the functionalities.
While filling framebuffer size in video hand-off structure use the
actual framebuffer region size as derived from gd->video_top and
gd->video_bottom instead of directly using the size populated in
video_uc_plat as it contains unaligned size.
Reported-by: Simon Glass <sjg@chromium.org> Signed-off-by: Devarsh Thakkar <devarsht@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Devarsh Thakkar [Tue, 5 Dec 2023 15:55:20 +0000 (21:25 +0530)]
video: Skip framebuffer reservation if already reserved
Skip framebufer reservation if it was already reserved from previous
stage and whose information was passed using a bloblist.
Return error in case framebuffer information received from bloblist is
invalid i.e NULL or empty.
While at it, improve the debug message to make it more clear that
address in discussion is of framebuffer and not bloblist and also match
it with printing scheme followed in video_reserve function.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Devarsh Thakkar [Tue, 5 Dec 2023 15:55:19 +0000 (21:25 +0530)]
common/board_f: Catch bloblist before starting reservations
Start reservations needed for init sequence only after catching
bloblists from previous stage.
This is to avoid catching bloblists in the middle causing gaps while
u-boot is reserving.
Adjust the relocaddr as per video hand-off information received from
previous stage so that further reservations start only after regions
reserved for previous stages
Skip reservation for video memory if it was already filled by a
bloblist.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Devarsh Thakkar [Tue, 5 Dec 2023 15:55:18 +0000 (21:25 +0530)]
board: ti: am62x: evm: Remove video_setup from spl_board_init
Remove video_setup from evm_init sequence since video memory is getting
called at an earlier place to make sure video memory is reserved at
the end of RAM.
Suggested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Devarsh Thakkar <devarsht@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Devarsh Thakkar [Tue, 5 Dec 2023 15:55:17 +0000 (21:25 +0530)]
arm: mach-k3: common: Reserve video memory from end of the RAM
Setup video memory before page table reservation using
"spl_reserve_video_from_ram_top" which ensures framebuffer memory gets
reserved from the end of RAM.
This is done to enable the next stage to directly skip the
pre-reserved area from previous stage right from the end of RAM without
having to make any gaps/holes to accommodate those regions which was the
case before as previous stage reserved region not from the end of RAM.
Use gd->ram_top instead of local ram_top and update gd->reloc_addr after
each reservation to ensure further regions are reserved properly.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com> Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Devarsh Thakkar [Tue, 5 Dec 2023 15:55:16 +0000 (21:25 +0530)]
spl: Enforce framebuffer reservation from end of RAM
Add an API which enforces framebuffer reservation from end of RAM.
This is done so that next stage can directly skip this region before
carrying out further reservations.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 29 Jan 2024 15:57:42 +0000 (10:57 -0500)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
- Some cleanups in header files: those do not affect the generated
binaries at all.
- The usual update of DT files from the kernel repo, mostly adding new
board files this time. On the wake of this there is one defconfig to
enable a new board, some H618 TV box branded as "Transpeed".
- Samuel's series to support SPL FIT image loading for 32-bit SoCs as
well, so far this was restricted to ARM64 boards. I refrained from
automatically enabling this everywhere, instead this requires user
intervention during board configuration. This allows to ship the
"crust" management processor firmware on H3 boards, which enables
better power saving.
- One defconfig for an older H3 board. There was a close-by defconfig
for a related board, but there are some differences which deserve a
separate file.
- Support for the EMAC driver to work with fixed-link PHYs, which allows
to directly wire the MAC to a switch IC.
Love Kumar [Fri, 19 Jan 2024 14:37:13 +0000 (20:07 +0530)]
test/py: scsi: Add test for scsi commands
Add a following test cases for scsi commands:
scsi_reset - To reset SCSI controller
scsi_info - To show available SCSI devices
scsi_scan - To (re-)scan SCSI bus
scsi_device - To show or set surrent device
scsi_part - To print partition table of selected SCSI device
Love Kumar [Fri, 19 Jan 2024 14:26:02 +0000 (19:56 +0530)]
test/py: usb: Add tests for USB device
Add the test cases for usb commands to test its various functionality
such as start, stop, reset, info, tree, storage, dev, part, ls, load,
and save. It also adds different file systems cases such as fat32, ext2
and ext4.
Love Kumar [Fri, 19 Jan 2024 14:25:50 +0000 (19:55 +0530)]
test/py: mmc: Add tests for MMC device
Add the test cases for mmc commands to test its various functionality
such as mmc list, dev, info, rescan, part, ls, load, and save. It also
adds different file systems cases such as fat32, ext2 and ext4.
Love Kumar [Fri, 19 Jan 2024 10:01:29 +0000 (15:31 +0530)]
test/py: secure: Add secure tests for Zynq & ZynqMP
Add test cases to verify the different type of secure boot images loaded
at DDR location for AMD's ZynqMP SoC. It also adds tests authentication
and decryption functionality using AES and RSA features for Zynq.
Love Kumar [Fri, 19 Jan 2024 05:38:34 +0000 (11:08 +0530)]
test/py: gpio: Add gpio pins generic test
Add gpio pins generic test for the set of gpio pin list to test various
gpio related functionality, such as the input, set, clear, and toggle,
it also tests the input and output functionality for shorted gpio pins.
This test depends on boardenv* configuration to define gpio pins names.
Caleb Connolly [Tue, 2 Jan 2024 11:55:30 +0000 (11:55 +0000)]
pytest: update requirements.txt
Update pygit2 and py to their latest versions. Even in the venv pygit2
still links against the system libgit2 library which is failing on
latest Arch Linux.
The py library also needs updating to fix a KeyNotFound exception during
test initialisation.
Samuel Holland [Tue, 31 Oct 2023 05:17:41 +0000 (00:17 -0500)]
sunxi: Consider SPL size limitations for FIT loading
Now that 32-bit SoCs can load U-Boot proper (and possibly other firmware)
from a FIT, people can use that by enabling CONFIG_SPL_LOAD_FIT.
However SPL_FIT_IMAGE_TINY is required to stay within the 24 or 32 KiB
SPL size limit on early SoCs; for consistency, enable it everywhere.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: drop unconditional FIT image enablement for all SoCs] Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Tue, 31 Oct 2023 05:17:40 +0000 (00:17 -0500)]
sunxi: binman: Support FIT generation for 32-bit SoCs
Some 32-bit SoCs can use SCP firmware to implement additional PSCI
functionality, such as system suspend. In order to load this firmware
from SPL, we need to generate and use a FIT instead of a legacy image.
Adjust the binman FIT definition so it does not rely on TF-A BL31, as
this is not used on 32-bit SoCs. Instead, after loading the firmware,
U-Boot proper is executed directly. This requires to provide an
entry point property for the U-Boot image node, which confuses some
loaders like sunxi-fel, so protect that to only be used if we have no
BL31.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: filter U-Boot entry point property] Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Samuel Holland [Tue, 31 Oct 2023 05:17:39 +0000 (00:17 -0500)]
sunxi: binman: Move BL31 and SCP firmware addresses to Kconfig
This is easier to read than the #ifdef staircase, provides better
visibility into the memory map (alongside the other Kconfig
definitions), and allows these addresses to be reused from code.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Tue, 31 Oct 2023 05:17:38 +0000 (00:17 -0500)]
sunxi: spl: Disable padding from SPL_PAD_TO
Starting with H6, Allwinner removed the artificial 32 KiB SPL size limit
from the boot ROM. Now SPL size is only limited by the available SRAM.
This limit ranges from 152 KiB on H6 to a whopping 2052 KiB on R329. To
take advantage of this additional space, we must increase SPL_MAX_SIZE.
Since we do not want to unnecessarily pad SPL out to these giant sizes,
we must set SPL_PAD_TO to zero. This causes no problems because binman
already takes care of appending the SPL payload at the right offset.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com>
projects / u-boot.git / log