Pali Rohár [Fri, 5 Feb 2021 14:32:28 +0000 (15:32 +0100)]
arm: a37xx: pci: Set Max Payload Size and Max Read Request Size to 512 bytes
Fix usage of VL805 XHCI PCIe controller when it is connected via PCIe to
Armada 3720 SOC. Without this U-Boot crashes when trying to access
enumerated USB devices connected to this XHCI PCIe controller.
This should be done according to the PCIe Link Initialization sequence, as
defined in Marvell Armada 3720 Functional Specification.
Linux has this code too.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Sun, 21 Feb 2021 01:06:28 +0000 (20:06 -0500)]
ppc: configs: Remove a few non-updated build configurations
In the cases of T2080RDB_SECURE_BOOT, T2080RDB_SRIO_PCIE_BOOT,
P2041RDB_SECURE_BOOT, P2041RDB_SRIO_PCIE_BOOT, P3041DS_SRIO_PCIE_BOOT
and P4080DS_SRIO_PCIE_BOOT while some forms of the board have been
migrated more fully to current build standards, these have not. Remove
them.
common: Add "ifndef __ASSEMBLY__" in asm/global_data.h
Commit "common: Drop asm/global_data.h from common header" added
asm/global_data.h into secure.h. However, secure.h will be included
by psci.S. Adding asm/global_data.h has caused compilation failure in
pcsi.S. Add "ifndef __ASSEMBLY__" in asm/global_data.h.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
When copying to a u32 field we should use sizeof(u32) and not
sizeof(*u32) in memcpy.
On 64bit systems like cortina_presidio-asic-emmc_defconfig using
sizeof(*u32) leads to a buffer overrun.
Fixes: febe13b438b3 ("net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
dm: ddr: socfpga: don't assign values that are not used
The values of left_edge[0] and right_edge[0] are overwritten before they
are used. Remove the superfluous assignments.
Fixes: 285b3cb939a8 ("dm: ddr: socfpga: fix gen5 ddr driver to not use bss") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Peter Robinson [Thu, 18 Feb 2021 20:06:37 +0000 (20:06 +0000)]
rng: iProc rng200: Rename ..._platdata variables to just ..._plat
In 8a8d24bd Simon dropped data from all the various _platdata calls
but it seems this wasn't caught for the RNG200 driver from when it
was posted to merged. This fixes that issue.
test/cmd/setexpr.c cannot be linked with CONFIG_CMD_SETEXPR=n:
ld.bfd: test/built-in.o: in function `setexpr_test_sub':
test/cmd/setexpr.c:227: undefined reference to `setexpr_regex_sub'
ld.bfd: test/built-in.o: in function `setexpr_test_backref':
test/cmd/setexpr.c:267: undefined reference to `setexpr_regex_sub'
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
In file included from lib/rsa/rsa-keyprop.c:16:
include/u-boot/rsa-mod-exp.h:65:24: warning:
‘struct udevice’ declared inside parameter list will not be visible
outside of this definition or declaration
65 | int rsa_mod_exp(struct udevice *dev, const uint8_t *sig,
| uint32_t sig_len,
| ^~~~~~~
include/u-boot/rsa-mod-exp.h:96:24: warning:
‘struct udevice’ declared inside parameter list will not be visible
outside of this definition or declaration
96 | int (*mod_exp)(struct udevice *dev, const uint8_t *sig,
|
by defining struct udevice.
Fixes: 401d1c4f5d2d ("common: Drop asm/global_data.h from common header") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Matthias Brugger [Tue, 16 Feb 2021 19:54:07 +0000 (20:54 +0100)]
configs: BPI-R2: Disable EFI Grub workaround
The EFI Grub workaround on BananaPi R2 slows down the boot process to
the point, that the watchdog will trigger a reboot before the kernel can
reset it. Fix this by disabeling the workaround.
Vincent Stehlé [Sun, 14 Feb 2021 18:39:04 +0000 (19:39 +0100)]
virtio: fix off by one device id comparison
VIRTIO_ID_MAX_NUM is the largest device ID plus 1. Therefore a device id
cannot be greater or equal to VIRTIO_ID_MAX_NUM. Fix the comparison
accordingly.
Fixes: 8fb49b4c7a82 ("dm: Add a new uclass driver for VirtIO transport devices") Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com>
Roger Pau Monne [Sat, 13 Feb 2021 10:06:32 +0000 (11:06 +0100)]
build/DTC: fix sed usage in DTC command
Current sed usage in the DTC command relies on GNU sed specific -i
option which has a slightly different syntax for BSD sed and always
expects an extension to be provided in order to create a backup file.
Instead drop the cat concatenation done before the sed call and use
sed itself to edit and concatenate the files.
No functional change intended.
Signed-off-by: Roger Pau Monné <royger@FreeBSD.org>
Marek Behún [Tue, 9 Feb 2021 20:23:47 +0000 (21:23 +0100)]
cmd: pinmux: depend on PINCTRL
The pinmux command uses functions pinctrl_get_pin_*(), which are missing
if PINCTRL config option is disabled.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Having the ability to support firmware FIT signatures on the SPL sounds
not so useful if the SPL is not supporting to load a (U-boot) firmware
as a FIT image.
Signed-off-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Selecting SPL_FIT_SIGNATURE (without selecting U-boot proper
verified boot first) breaks the build due to
CONFIG_FIT_SIGNATURE_MAX_SIZE being undefined, in addition to Kconfig
warnings on RSA and IMAGE_SIGN_INFO unmet dependencies.
Signed-off-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
If an unknown directory item type is encountered, we will print the type
number left padded with spaces, enclosed by '?', instead of '<' and '>',
i.e.:
? 30? ............................. name
Signed-off-by: Marek Behún <marek.behun@nic.cz> Fixes: 325dd1f642dd ("fs: btrfs: Use btrfs_iter_dir() to replace ...") Cc: David Sterba <dsterba@suse.com> Cc: Qu Wenruo <wqu@suse.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Qu Wenruo <wqu@suse.com>
Wasim Khan [Thu, 4 Feb 2021 14:44:04 +0000 (15:44 +0100)]
cmd: fdt: skip board specific fixup using env variable
Sometimes it is useful to boot OS with already fixed-up
device tree. Check for env variable 'skip_board_fixup'
before calling ft_board_setup().
Current behaviour is unchanged, additionally user can
set skip_board_fixup to 1 to skip the fixup.
Tom Rini [Tue, 26 Jan 2021 16:44:37 +0000 (11:44 -0500)]
cmd: pwm: Rework argc sanity checking
Currently, we check argc in a number of places to make sure that we have
all of the required arguments for each of the pwm sub-commands.
However, there's at least one place where we've got dead code as we'll
never have argc == 0, due to checking that argc was at least 4 earlier
and having only subtracted 3. Rework things so that when we have
determined our subcommand make sure we have the right number of
arguments for it, or error out. This means we can stop checking against
argc again later.
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
Brandon Maier [Wed, 20 Jan 2021 20:28:30 +0000 (14:28 -0600)]
spi: zynqmp_gqspi: fix set_speed bug on multiple runs
If zynqmp_qspi_set_speed() is called multiple times with the same speed,
then on the second call it will skip recalculating the baud_rate_val as
it assumes the speed is already configured correctly. But it will still
write the baud_rate_val to the configuration register and call
zynqmp_gqspi_set_tapdelay(). Because it skipped recalculating the
baud_rate_val, it will use the initial value of 0 . This causes the
driver to run at maximum speed which for many spi flashes is too fast and
causes data corruption.
Instead only write out a new baud_rate_val if we have calculated the
correct baud_rate_val.
This opens up another issue with the "if (speed == 0)", we don't save
off the new plat->speed_hz value when setting the baud rate on the
speed=0 path. Instead mimic what the Linux zynqmp gqspi driver does, and
have speed==0 just use the same calculation as a normal speed. That will
cause the baud_rate_val to use the slowest speed possible, which is the
safest option.
Michal Simek [Wed, 17 Feb 2021 07:55:34 +0000 (08:55 +0100)]
arm64: zynqmp: Rename zc1275/zcu1275 to be aligned with DT name
Folder names corresponds to DT name. These boards have been renamed from
zc1275 to zcu1275 by commit shown below and this should be the part of that
commit.
Fixes: 420d44678119 ("arm64: zynqmp: Rename zc1275 to zcu1275") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
T Karthik Reddy [Wed, 3 Feb 2021 10:10:48 +0000 (03:10 -0700)]
net: gem: Enable ethernet rx clock for versal
Enable rx clock along with tx clock for versal platform. Use compatible
data to enable/disable clocks in the driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Michal Simek [Tue, 9 Feb 2021 14:28:15 +0000 (15:28 +0100)]
clk: zynq: Add dummy clock enable function
A lot of Xilinx drivers are checking -ENOSYS which means that clock driver
doesn't have enable function. Remove this checking from drivers and create
dummy enable function as was done for clk_fixed_rate driver by
commit 6bf6d81c1112 ("clk: fixed_rate: add dummy enable() function").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 9 Feb 2021 07:50:22 +0000 (08:50 +0100)]
arm64: zynqmp: Do not clear reset reason
There is no need to clear reset reason register because it is protected by
PMUFW already which is reported when verbose log is enabled as:
pm_core.c@733 APU> No write permission to 0xFF5E0220
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michael Walle [Wed, 10 Feb 2021 21:42:29 +0000 (22:42 +0100)]
fpga: zynqpl: fix buffer alignment
Due to pointer arithmetic, "sizeof(u32) * ARCH_DMA_MINALIGN" is
subtracted. It seems that the original intention was to just subtract
ARCH_DMA_MINALIGN. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Mon, 22 Feb 2021 14:11:27 +0000 (09:11 -0500)]
Merge tag 'video-for-v2021.04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- splash_source warning fix when building with 64-bit toolchains
- lq123p1jx31 and nv101wxmn51 compatible in simple panel driver
- remove not used mb862xx driver
- add Himax HX8238D panel driver
- s/video_uc_platdata/video_uc_plat/
Neil Armstrong [Fri, 19 Feb 2021 07:31:47 +0000 (08:31 +0100)]
button: add udevice forward declaration
After 401d1c4f5d2d ("common: Drop asm/global_data.h from common header")
build fails with :
drivers/button/button-uclass.c:13:5: error: conflicting types for 'button_get_by_label'
int button_get_by_label(const char *label, struct udevice **devp)
^~~~~~~~~~~~~~~~~~~
Adding struct udevice forward declaration in button.h solves the build error.
Fixes: 401d1c4f5d2d ("common: Drop asm/global_data.h from common header") Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Dario Binacchi [Sat, 13 Feb 2021 11:09:19 +0000 (12:09 +0100)]
arm: dts: sync am33xx-clocks with Linux 5.9-rc7
The commit 6337d53fdf45 ("arm: dts: sync am33xx with Linux 5.9-rc7")
synchronized the am33xx-clocks.dtsi file with Linux 5.9-rc7 with the
exception of two nodes. I think I was wrong and it is better to keep
the two files similar and possibly make changes to the *-u-boot.dtsi
files.
Dario Binacchi [Sat, 13 Feb 2021 11:02:30 +0000 (12:02 +0100)]
clk: ti: improve debug messages for clkctrl driver
The previous version printed the same debug message for both the enable
and disable routines without highlighting whether you were enabling or
disabling the module. It is now clear whether you are enabling or
disabling the module.
When trying to port our mpc8309-based board to DM_ETH, on top of
Heiko's patches, I found that nothing in mdio-uclass.c seems to
support the use of a fixed-link subnode of the ethernet DT node. That
is, the ethernet node looks like
but the current code expects there to be phy-handle property. Adding
that, i.e.
phy-handle = <&enet0phy>;
enet0phy: fixed-link {
just makes the code break a few lines later since a fixed-link node
doesn't have a reg property. Ignoring the dtc complaint and adding a
dummy reg property, we of course hit "can't find MDIO bus for node
ethernet@2000" since indeed, the parent node of the phy node does not
represent an MDIO bus. So that's obviously the wrong path.
Now, in linux, it seems that the fixed link case is treated specially;
in the of_phy_get_and_connect() which roughly corresponds to
dm_eth_connect_phy_handle() we have
if (of_phy_is_fixed_link(np)) {
ret = of_phy_register_fixed_link(np);
...
} else {
phy_np = of_parse_phandle(np, "phy-handle", 0);
...
}
And U-Boot's phy_connect() does have support for fixed-link
subnodes. Calling phy_connect() directly with NULL bus and a dummy
address does seem to make the ethernet work.
Tom Rini [Sun, 21 Feb 2021 16:17:30 +0000 (11:17 -0500)]
Merge tag 'efi-2021-04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-04-rc3
Bug fixes:
* Let EFI simple file protocol access last block of partition
* Correct conversion of multi-part device paths in
EFI_DEVICE_PATH_TO_TEXT_PROTOCOL.ConvertDevicePathToText()
Our current implementation of
EFI_DEVICE_PATH_TO_TEXT_PROTOCOL.ConvertDevicePathToText() truncates multi
part device paths after the first part. We should convert all parts.
Render device path instance ends as commas. This is not explicitly
described in the UEFI spec but mimics what EDK II does.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Igor Opaniuk [Tue, 9 Feb 2021 11:52:45 +0000 (13:52 +0200)]
dm: i2c: use CONFIG_IS_ENABLED macro for DM_I2C/DM_I2C_GPIO
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Igor Opaniuk [Tue, 9 Feb 2021 11:52:44 +0000 (13:52 +0200)]
board: freescale: drop CONFIG_DM_I2C undefs
Drop CONFIG_DM_I2C undefs from board header files, and make them
disabled on these boards in defconfigs instead.
Disabling on Kconfig symbol was done automatically with this script:
cd configs
files=(*ls1046a*)
files2=(*T104*RDB*)
files3=(ls1021atwr_*)
files4=("imx8mp_evk_defconfig phycore-imx8mp_defconfig")
combine=("${files[@]}" "${files2[@]}" "${files3[@]}" "${files4[@]}")
cd ..
for item in ${combine[*]}
do
echo "Adjusting $item"
echo "# CONFIG_SPL_DM_I2C is not set" >> configs/$item
make $item && make savedefconfig && cp defconfig configs/$item
done
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Tom Rini <trini@konsulko.com>
Igor Opaniuk [Tue, 9 Feb 2021 11:52:43 +0000 (13:52 +0200)]
dm: i2c: allow disabling driver model in SPL
At present if U-Boot proper uses driver model for I2C, then SPL has to
also. While this is desirable, it places a significant barrier to moving
to driver model in some cases. For example, with a space-constrained SPL
it may be necessary to enable CONFIG_SPL_OF_PLATDATA which involves
adjusting some drivers.
This patch introduces a separate Kconfig symbols for enabling DM_I2C and
DM_I2C_GPIO support in SPL.
This will also help to get away from dirty workarounds to
achieve non-DM I2C support for SPL, which is currently used in some
board header files like:
ifdef CONFIG_SPL_BUILD
undef CONFIG_DM_I2C
endif
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Tom Rini <trini@konsulko.com>
Eugen Hristev [Fri, 4 Dec 2020 16:06:55 +0000 (18:06 +0200)]
i2c: at91: fix crash when using 'i2c probe'
When issuing 'i2c probe', the driver was crashing, because at probe
there is a request with zero length buffer to write to i2c bus.
The xfer_msg function assumes the buffer is always there, and never
checks for the buffer length.
Harm Berntsen [Sun, 29 Nov 2020 09:47:15 +0000 (09:47 +0000)]
i2c: i2c-gpio: Fix GPIO output
The dm_gpio_set_dir_flags function cannot be used to update the
configuration of a GPIO pin because it does a bitwise OR with the
existing flags. Looks like commit 788ea834124b ("gpio: add function
_dm_gpio_set_dir_flags") has introduced this behaviour and the i2c-gpio
driver has been broken since.
Marek Vasut [Fri, 15 Jan 2021 23:27:50 +0000 (00:27 +0100)]
ARM: rmobile: Enable CONFIG_PCI_REGION_MULTI_ENTRY on RCar3
R-Car3 can have multiple regions of type memory in DT, enable
CONFIG_PCI_REGION_MULTI_ENTRY to handle those instead of using
just one of the memory regions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Marek Vasut [Fri, 15 Jan 2021 23:33:17 +0000 (00:33 +0100)]
pci: renesas: Fix BAR mapping on Gen3
Because the first PCIExAR(n) register is configured with the mapping,
It is the second PCIExAR(n) register that must be written with 0, not
the last one. Update the n from 4 to 1 to select the correct register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Andre Przywara [Sun, 14 Feb 2021 10:35:18 +0000 (10:35 +0000)]
fdt/sunxi: Remove OF_STDOUT_PATH
OF_STDOUT_PATH was meant to hold the devicetree path to the serial
console, to be put into the linux,stdout-path property of the chosen node.
The only user of that was sunxi, and it was actually wrong for years
there: the paths hardcoded in sunxi_common.h were not matching the DTs,
evident by the leading 0's in nodenames, which have been removed years
ago.
On top of that, "linux,stdout-path" is now deprecated for a while (Linux
commit 2a9d832cc9aae from November 2014), and also all modern DTs
(including those included in U-Boot) carry a "stdout-path" property
already.
So remove the stanza from sunxi_common.h, and, since this was the last
user, also remove the associated bits from the rest of U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tobias Schramm [Sun, 14 Feb 2021 23:19:58 +0000 (00:19 +0100)]
sunxi: support boot console on uart1 for sun8i
The A23, A33, H3, H5, A83T, V3 and Sochip S3 sun8i SoCs can mux uart1 on
GPIOs PG6 and PG7. This patch adds support for using uart1 on those pins
as boot console.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 8 Feb 2021 06:04:57 +0000 (00:04 -0600)]
sunxi: Remove dead ifdefs in sunxi-common.h
As variables were moved to Kconfig, some of the surrounding ifdefs were
left around, even though they were empty. Clean them up.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 1 Feb 2021 17:25:57 +0000 (18:25 +0100)]
sunxi: spl: Fix H616 clock initialization
It turns out that there is a magic bit in PRCM region which seemingly
makes PLLs work if it's enabled. Sadly, there is no documentation what
it does exactly, so we'll just mimick BSP boot0 behaviour and enable it
before any clock is set up.
Fixes: b18bd53d6cde ("sunxi: introduce support for H616 clocks") Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
drivers: video: Add Support for Himax HX8238D Panel
* SPI based initialization for HX8238D
* Resolution: 320x240
* Color-Mode: RGB
* Initial Work is done by Sjoerd Simons
https://gitlab.apertis.org/packaging/u-boot/-/blob\
/5f259720e3e64965d50da89a841ad6eb256a47df/debian/patches\
/apertis/powertools/0005-video-Add-Himax-HX8238-D-driver.patch
* Tested on Bosch Guardian Board
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
common/splash_source.c: In function 'splash_load_raw':
common/splash_source.c:100:12: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
100 | bmp_hdr = (struct bmp_header *)bmp_load_addr;
| ^
common/splash_source.c: In function 'splash_sf_read_raw':
common/splash_source.c:39:47: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
39 | return spi_flash_read(sf, offset, read_size, (void *)bmp_load_addr);
| ^
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 19 Feb 2021 16:56:14 +0000 (11:56 -0500)]
Merge tag 'mmc-2021-2-19' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmc
- mmc_spi improvement
- added mmc-pwrseq to remove duplicated code
- fix response timeout after switch command
- sdhci: skip cache invalidation if DMA is not used
Jaehoon Chung [Tue, 16 Feb 2021 01:16:55 +0000 (10:16 +0900)]
ARM: mach-meson: select MMC_PWRSEQ config
Before time, PWRSEQ is selected since below commit.
commit 262d34363373 ("board: amlogic: select PWRSEQ for all amlogic platform")
Select MMC_PWRSEQ config because of introducing CONFIG_MMC_PWRSEQ for
only eMMC module.
projects / u-boot.git / log