select VENDOR_KM
select KM_ENABLE_FULL_DM_DTS_SUPPORT
-config TARGET_TQM834X
- bool "Support TQM834x"
- select ARCH_MPC8349
-
-
config TARGET_GAZERBEAM
bool "Support gazerbeam"
select ARCH_MPC8308
source "board/freescale/mpc837xerdb/Kconfig"
source "board/ids/ids8313/Kconfig"
source "board/keymile/Kconfig"
-source "board/tqc/tqm834x/Kconfig"
source "board/gdsys/mpc8308/Kconfig"
endmenu
+++ /dev/null
-if TARGET_TQM834X
-
-config SYS_BOARD
- default "tqm834x"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM834x"
-
-endif
+++ /dev/null
-TQM834X BOARD
-#M: -
-S: Maintained
-F: board/tqc/tqm834x/
-F: include/configs/TQM834x.h
-F: configs/TQM834x_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright 2004 Freescale Semiconductor, Inc.
-
-obj-y += tqm834x.o
-obj-$(CONFIG_PCI) += pci.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- * Copyright (C) 2006-2009 Freescale Semiconductor, Inc.
- */
-
-#include <init.h>
-#include <asm/mmu.h>
-#include <asm/io.h>
-#include <common.h>
-#include <mpc83xx.h>
-#include <pci.h>
-#include <i2c.h>
-#include <asm/fsl_i2c.h>
-#include <linux/delay.h>
-
-static struct pci_region pci1_regions[] = {
- {
- bus_start: CONFIG_SYS_PCI1_MEM_BASE,
- phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
- size: CONFIG_SYS_PCI1_MEM_SIZE,
- flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
- },
- {
- bus_start: CONFIG_SYS_PCI1_IO_BASE,
- phys_start: CONFIG_SYS_PCI1_IO_PHYS,
- size: CONFIG_SYS_PCI1_IO_SIZE,
- flags: PCI_REGION_IO
- },
- {
- bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
- phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
- size: CONFIG_SYS_PCI1_MMIO_SIZE,
- flags: PCI_REGION_MEM
- },
-};
-
-/*
- * pci_init_board()
- *
- * NOTICE: MPC8349 internally has two PCI controllers (PCI1 and PCI2) but since
- * per TQM834x design physical connections to external devices (PCI sockets)
- * are routed only to the PCI1 we do not account for the second one - this code
- * supports PCI1 module only. Should support for the PCI2 be required in the
- * future it needs a separate pci_controller structure (above) and handling -
- * please refer to other boards' implementation for dual PCI host controllers,
- * for example board/Marvell/db64360/pci.c, pci_init_board()
- *
- */
-void
-pci_init_board(void)
-{
- volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
- volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
- struct pci_region *reg[] = { pci1_regions };
- u32 reg32;
-
- /*
- * Configure PCI controller and PCI_CLK_OUTPUT
- *
- * WARNING! only PCI_CLK_OUTPUT1 is enabled here as this is the one
- * line actually used for clocking all external PCI devices in TQM83xx.
- * Enabling other PCI_CLK_OUTPUT lines may lead to board's hang for
- * unknown reasons - particularly PCI_CLK_OUTPUT6 and PCI_CLK_OUTPUT7
- * are known to hang the board; this issue is under investigation
- * (13 oct 05)
- */
- reg32 = OCCR_PCICOE1;
-#if 0
- /* enabling all PCI_CLK_OUTPUT lines HANGS the board... */
- reg32 = 0xff000000;
-#endif
- if (clk->spmr & SPMR_CKID) {
- /* PCI Clock is half CONFIG_SYS_CLK_FREQ so need to set up OCCR
- * fields accordingly */
- reg32 |= (OCCR_PCI1CR | OCCR_PCI2CR);
-
- reg32 |= (OCCR_PCICD0 | OCCR_PCICD1 | OCCR_PCICD2 \
- | OCCR_PCICD3 | OCCR_PCICD4 | OCCR_PCICD5 \
- | OCCR_PCICD6 | OCCR_PCICD7);
- }
-
- clk->occr = reg32;
- udelay(2000);
-
- /* Configure PCI Local Access Windows */
- pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
- pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_512M;
-
- pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
- pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_16M;
-
- udelay(2000);
-
- mpc83xx_pci_init(1, reg);
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <fdt_support.h>
-#include <init.h>
-#include <ioports.h>
-#include <log.h>
-#include <mpc83xx.h>
-#include <asm/global_data.h>
-#include <asm/mpc8349_pci.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <asm/mmu.h>
-#include <pci.h>
-#include <flash.h>
-#include <linux/delay.h>
-#include <mtd/cfi_flash.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define IOSYNC asm("eieio")
-#define ISYNC asm("isync")
-#define SYNC asm("sync")
-#define FPW FLASH_PORT_WIDTH
-#define FPWV FLASH_PORT_WIDTHV
-
-#define DDR_MAX_SIZE_PER_CS 0x20000000
-
-#if defined(DDR_CASLAT_20)
-#define TIMING_CASLAT TIMING_CFG1_CASLAT_20
-#define MODE_CASLAT DDR_MODE_CASLAT_20
-#else
-#define TIMING_CASLAT TIMING_CFG1_CASLAT_25
-#define MODE_CASLAT DDR_MODE_CASLAT_25
-#endif
-
-#define INITIAL_CS_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_12 | \
- CSCONFIG_COL_BIT_9)
-
-/* External definitions */
-ulong flash_get_size (ulong base, int banknum);
-
-/* Local functions */
-static int detect_num_flash_banks(void);
-static long int get_ddr_bank_size(short cs, long *base);
-static void set_cs_bounds(short cs, ulong base, ulong size);
-static void set_cs_config(short cs, long config);
-static void set_ddr_config(void);
-
-/* Local variable */
-static volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
-
-/**************************************************************************
- * Board initialzation after relocation to RAM. Used to detect the number
- * of Flash banks on TQM834x.
- */
-int board_early_init_r (void) {
- /* sanity check, IMMARBAR should be mirrored at offset zero of IMMR */
- if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
- return 0;
-
- /* detect the number of Flash banks */
- return detect_num_flash_banks();
-}
-
-/**************************************************************************
- * DRAM initalization and size detection
- */
-int dram_init(void)
-{
- long bank_size;
- long size;
- int cs;
-
- /* during size detection, set up the max DDRLAW size */
- im->sysconf.ddrlaw[0].bar = CONFIG_SYS_SDRAM_BASE;
- im->sysconf.ddrlaw[0].ar = (LAWAR_EN | LAWAR_SIZE_2G);
-
- /* set CS bounds to maximum size */
- for(cs = 0; cs < 4; ++cs) {
- set_cs_bounds(cs,
- CONFIG_SYS_SDRAM_BASE + (cs * DDR_MAX_SIZE_PER_CS),
- DDR_MAX_SIZE_PER_CS);
-
- set_cs_config(cs, INITIAL_CS_CONFIG);
- }
-
- /* configure ddr controller */
- set_ddr_config();
-
- udelay(200);
-
- /* enable DDR controller */
- im->ddr.sdram_cfg = (SDRAM_CFG_MEM_EN |
- SDRAM_CFG_SREN |
- SDRAM_CFG_SDRAM_TYPE_DDR1);
- SYNC;
-
- /* size detection */
- debug("\n");
- size = 0;
- for(cs = 0; cs < 4; ++cs) {
- debug("\nDetecting Bank%d\n", cs);
-
- bank_size = get_ddr_bank_size(cs,
- (long *)(CONFIG_SYS_SDRAM_BASE + size));
- size += bank_size;
-
- debug("DDR Bank%d size: %ld MiB\n\n", cs, bank_size >> 20);
-
- /* exit if less than one bank */
- if(size < DDR_MAX_SIZE_PER_CS) break;
- }
-
- gd->ram_size = size;
-
- return 0;
-}
-
-/**************************************************************************
- * checkboard()
- */
-int checkboard (void)
-{
- puts("Board: TQM834x\n");
-
-#ifdef CONFIG_PCI
- volatile immap_t * immr;
- u32 w, f;
-
- immr = (immap_t *)CONFIG_SYS_IMMR;
- if (!(immr->reset.rcwh & HRCWH_PCI_HOST)) {
- printf("PCI: NOT in host mode..?!\n");
- return 0;
- }
-
- /* get bus width */
- w = 32;
- if (immr->reset.rcwh & HRCWH_64_BIT_PCI)
- w = 64;
-
- /* get clock */
- f = gd->pci_clk;
-
- printf("PCI1: %d bit, %d MHz\n", w, f / 1000000);
-#else
- printf("PCI: disabled\n");
-#endif
- return 0;
-}
-
-
-/**************************************************************************
- *
- * Local functions
- *
- *************************************************************************/
-
-/**************************************************************************
- * Detect the number of flash banks (1 or 2). Store it in
- * a global variable tqm834x_num_flash_banks.
- * Bank detection code based on the Monitor code.
- */
-static int detect_num_flash_banks(void)
-{
- typedef unsigned long FLASH_PORT_WIDTH;
- typedef volatile unsigned long FLASH_PORT_WIDTHV;
- FPWV *bank1_base;
- FPWV *bank2_base;
- FPW bank1_read;
- FPW bank2_read;
- ulong bank1_size;
- ulong bank2_size;
- ulong total_size;
-
- cfi_flash_num_flash_banks = 2; /* assume two banks */
-
- /* Get bank 1 and 2 information */
- bank1_size = flash_get_size(CONFIG_SYS_FLASH_BASE, 0);
- debug("Bank1 size: %lu\n", bank1_size);
- bank2_size = flash_get_size(CONFIG_SYS_FLASH_BASE + bank1_size, 1);
- debug("Bank2 size: %lu\n", bank2_size);
- total_size = bank1_size + bank2_size;
-
- if (bank2_size > 0) {
- /* Seems like we've got bank 2, but maybe it's mirrored 1 */
-
- /* Set the base addresses */
- bank1_base = (FPWV *) (CONFIG_SYS_FLASH_BASE);
- bank2_base = (FPWV *) (CONFIG_SYS_FLASH_BASE + bank1_size);
-
- /* Put bank 2 into CFI command mode and read */
- bank2_base[0x55] = 0x00980098;
- IOSYNC;
- ISYNC;
- bank2_read = bank2_base[0x10];
-
- /* Read from bank 1 (it's in read mode) */
- bank1_read = bank1_base[0x10];
-
- /* Reset Flash */
- bank1_base[0] = 0x00F000F0;
- bank2_base[0] = 0x00F000F0;
-
- if (bank2_read == bank1_read) {
- /*
- * Looks like just one bank, but not sure yet. Let's
- * read from bank 2 in autosoelect mode.
- */
- bank2_base[0x0555] = 0x00AA00AA;
- bank2_base[0x02AA] = 0x00550055;
- bank2_base[0x0555] = 0x00900090;
- IOSYNC;
- ISYNC;
- bank2_read = bank2_base[0x10];
-
- /* Read from bank 1 (it's in read mode) */
- bank1_read = bank1_base[0x10];
-
- /* Reset Flash */
- bank1_base[0] = 0x00F000F0;
- bank2_base[0] = 0x00F000F0;
-
- if (bank2_read == bank1_read) {
- /*
- * In both CFI command and autoselect modes,
- * we got the some data reading from Flash.
- * There is only one mirrored bank.
- */
- cfi_flash_num_flash_banks = 1;
- total_size = bank1_size;
- }
- }
- }
-
- debug("Number of flash banks detected: %d\n", cfi_flash_num_flash_banks);
-
- /* set OR0 and BR0 */
- set_lbc_or(0, OR_GPCM_CSNT | OR_GPCM_ACS_DIV4 | OR_GPCM_SCY_5 |
- OR_GPCM_TRLX | (-(total_size) & OR_GPCM_AM));
- set_lbc_br(0, (CONFIG_SYS_FLASH_BASE & BR_BA) |
- (BR_MS_GPCM | BR_PS_32 | BR_V));
-
- return (0);
-}
-
-/*************************************************************************
- * Detect the size of a ddr bank. Sets CS bounds and CS config accordingly.
- */
-static long int get_ddr_bank_size(short cs, long *base)
-{
- /* This array lists all valid DDR SDRAM configurations, with
- * Bank sizes in bytes. (Refer to Table 9-27 in the MPC8349E RM).
- * The last entry has to to have size equal 0 and is igonred during
- * autodection. Bank sizes must be in increasing order of size
- */
- struct {
- long row;
- long col;
- long size;
- } conf[] = {
- {CSCONFIG_ROW_BIT_12, CSCONFIG_COL_BIT_8, 32 << 20},
- {CSCONFIG_ROW_BIT_12, CSCONFIG_COL_BIT_9, 64 << 20},
- {CSCONFIG_ROW_BIT_12, CSCONFIG_COL_BIT_10, 128 << 20},
- {CSCONFIG_ROW_BIT_13, CSCONFIG_COL_BIT_9, 128 << 20},
- {CSCONFIG_ROW_BIT_13, CSCONFIG_COL_BIT_10, 256 << 20},
- {CSCONFIG_ROW_BIT_13, CSCONFIG_COL_BIT_11, 512 << 20},
- {CSCONFIG_ROW_BIT_14, CSCONFIG_COL_BIT_10, 512 << 20},
- {CSCONFIG_ROW_BIT_14, CSCONFIG_COL_BIT_11, 1024 << 20},
- {0, 0, 0}
- };
-
- int i;
- int detected;
- long size;
-
- detected = -1;
- for(i = 0; conf[i].size != 0; ++i) {
-
- /* set sdram bank configuration */
- set_cs_config(cs, CSCONFIG_EN | conf[i].col | conf[i].row);
-
- debug("Getting RAM size...\n");
- size = get_ram_size(base, DDR_MAX_SIZE_PER_CS);
-
- if((size == conf[i].size) && (i == detected + 1))
- detected = i;
-
- debug("Trying %ld x %ld (%ld MiB) at addr %p, detected: %ld MiB\n",
- conf[i].row,
- conf[i].col,
- conf[i].size >> 20,
- base,
- size >> 20);
- }
-
- if(detected == -1){
- /* disable empty cs */
- debug("\nNo valid configurations for CS%d, disabling...\n", cs);
- set_cs_config(cs, 0);
- return 0;
- }
-
- debug("\nDetected configuration %ld x %ld (%ld MiB) at addr %p\n",
- conf[detected].row, conf[detected].col, conf[detected].size >> 20, base);
-
- /* configure cs ro detected params */
- set_cs_config(cs, CSCONFIG_EN | conf[detected].row |
- conf[detected].col);
-
- set_cs_bounds(cs, (long)base, conf[detected].size);
-
- return(conf[detected].size);
-}
-
-/**************************************************************************
- * Sets DDR bank CS bounds.
- */
-static void set_cs_bounds(short cs, ulong base, ulong size)
-{
- debug("Setting bounds %08lx, %08lx for cs %d\n", base, size, cs);
- if(size == 0){
- im->ddr.csbnds[cs].csbnds = 0x00000000;
- } else {
- im->ddr.csbnds[cs].csbnds =
- ((base >> CSBNDS_SA_SHIFT) & CSBNDS_SA) |
- (((base + size - 1) >> CSBNDS_EA_SHIFT) &
- CSBNDS_EA);
- }
- SYNC;
-}
-
-/**************************************************************************
- * Sets DDR banks CS configuration.
- * config == 0x00000000 disables the CS.
- */
-static void set_cs_config(short cs, long config)
-{
- debug("Setting config %08lx for cs %d\n", config, cs);
- im->ddr.cs_config[cs] = config;
- SYNC;
-}
-
-/**************************************************************************
- * Sets DDR clocks, timings and configuration.
- */
-static void set_ddr_config(void) {
- /* clock control */
- im->ddr.sdram_clk_cntl = DDR_SDRAM_CLK_CNTL_SS_EN |
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05;
- SYNC;
-
- /* timing configuration */
- im->ddr.timing_cfg_1 =
- (4 << TIMING_CFG1_PRETOACT_SHIFT) |
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) |
- (4 << TIMING_CFG1_ACTTORW_SHIFT) |
- (5 << TIMING_CFG1_REFREC_SHIFT) |
- (3 << TIMING_CFG1_WRREC_SHIFT) |
- (3 << TIMING_CFG1_ACTTOACT_SHIFT) |
- (1 << TIMING_CFG1_WRTORD_SHIFT) |
- (TIMING_CFG1_CASLAT & TIMING_CASLAT);
-
- im->ddr.timing_cfg_2 =
- TIMING_CFG2_CPO_DEF |
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT);
- SYNC;
-
- /* don't enable DDR controller yet */
- im->ddr.sdram_cfg =
- SDRAM_CFG_SREN |
- SDRAM_CFG_SDRAM_TYPE_DDR1;
- SYNC;
-
- /* Set SDRAM mode */
- im->ddr.sdram_mode =
- ((DDR_MODE_EXT_MODEREG | DDR_MODE_WEAK) <<
- SDRAM_MODE_ESD_SHIFT) |
- ((DDR_MODE_MODEREG | DDR_MODE_BLEN_4) <<
- SDRAM_MODE_SD_SHIFT) |
- ((DDR_MODE_CASLAT << SDRAM_MODE_SD_SHIFT) &
- MODE_CASLAT);
- SYNC;
-
- /* Set fast SDRAM refresh rate */
- im->ddr.sdram_interval =
- (DDR_REFINT_166MHZ_7US << SDRAM_INTERVAL_REFINT_SHIFT) |
- (DDR_BSTOPRE << SDRAM_INTERVAL_BSTOPRE_SHIFT);
- SYNC;
-
- /* Workaround for DDR6 Erratum
- * see MPC8349E Device Errata Rev.8, 2/2006
- * This workaround influences the MPC internal "input enables"
- * dependent on CAS latency and MPC revision. According to errata
- * sheet the internal reserved registers for this workaround are
- * not available from revision 2.0 and up.
- */
-
- /* Get REVID from register SPRIDR. Skip workaround if rev >= 2.0
- * (0x200)
- */
- if ((im->sysconf.spridr & SPRIDR_REVID) < 0x200) {
-
- /* There is a internal reserved register at IMMRBAR+0x2F00
- * which has to be written with a certain value defined by
- * errata sheet.
- */
- u32 *reserved_p = (u32 *)((u8 *)im + 0x2f00);
-
-#if defined(DDR_CASLAT_20)
- *reserved_p = 0x201c0000;
-#else
- *reserved_p = 0x202c0000;
-#endif
- }
-}
-
-#ifdef CONFIG_OF_BOARD_SETUP
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
- ft_cpu_setup(blob, bd);
-
-#ifdef CONFIG_PCI
- ft_pci_setup(blob, bd);
-#endif /* CONFIG_PCI */
-
- return 0;
-}
-#endif /* CONFIG_OF_BOARD_SETUP */
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x80000000
-CONFIG_ENV_SIZE=0x8000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_CLK_FREQ=66666000
-CONFIG_MPC83xx=y
-CONFIG_HIGH_BATS=y
-CONFIG_TARGET_TQM834X=y
-CONFIG_SYS_IMMR=0xff400000
-CONFIG_DDR_MC_CLOCK_MODE_1_1=y
-CONFIG_SYSTEM_PLL_FACTOR_4_1=y
-CONFIG_CORE_PLL_RATIO_2_1=y
-CONFIG_PCI_HOST_MODE_ENABLE=y
-CONFIG_PCI_INT_ARBITER1_ENABLE=y
-CONFIG_BOOT_MEMORY_SPACE_LOW=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC1_MODE_GMII=y
-CONFIG_TSEC2_MODE_GMII=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="SDRAM_LOWER"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_256_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="SDRAM_UPPER"
-CONFIG_BAT1_BASE=0x10000000
-CONFIG_BAT1_LENGTH_256_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="STACK_IN_DCACHE"
-CONFIG_BAT2_BASE=0x20000000
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT2_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT3=y
-CONFIG_BAT3_NAME="PCI_MEM_BASE"
-CONFIG_BAT3_BASE=0x90000000
-CONFIG_BAT3_LENGTH_256_MBYTES=y
-CONFIG_BAT3_ACCESS_RW=y
-CONFIG_BAT3_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT3_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT3_USER_MODE_VALID=y
-CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT4=y
-CONFIG_BAT4_NAME="PCI_MMIO"
-CONFIG_BAT4_BASE=0xA0000000
-CONFIG_BAT4_LENGTH_256_MBYTES=y
-CONFIG_BAT4_ACCESS_RW=y
-CONFIG_BAT4_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT4_ICACHE_GUARDED=y
-CONFIG_BAT4_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT4_DCACHE_GUARDED=y
-CONFIG_BAT4_USER_MODE_VALID=y
-CONFIG_BAT4_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT5=y
-CONFIG_BAT5_NAME="PCI_IO"
-CONFIG_BAT5_BASE=0xE2000000
-CONFIG_BAT5_LENGTH_16_MBYTES=y
-CONFIG_BAT5_ACCESS_RW=y
-CONFIG_BAT5_ICACHE_INHIBITED=y
-CONFIG_BAT5_ICACHE_GUARDED=y
-CONFIG_BAT5_DCACHE_INHIBITED=y
-CONFIG_BAT5_DCACHE_GUARDED=y
-CONFIG_BAT5_USER_MODE_VALID=y
-CONFIG_BAT5_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT6=y
-CONFIG_BAT6_NAME="IMMR"
-CONFIG_BAT6_BASE=0xFF400000
-CONFIG_BAT6_LENGTH_1_MBYTES=y
-CONFIG_BAT6_ACCESS_RW=y
-CONFIG_BAT6_ICACHE_INHIBITED=y
-CONFIG_BAT6_ICACHE_GUARDED=y
-CONFIG_BAT6_DCACHE_INHIBITED=y
-CONFIG_BAT6_DCACHE_GUARDED=y
-CONFIG_BAT6_USER_MODE_VALID=y
-CONFIG_BAT6_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT7=y
-CONFIG_BAT7_NAME="FLASH"
-CONFIG_BAT7_BASE=0x80000000
-CONFIG_BAT7_LENGTH_256_MBYTES=y
-CONFIG_BAT7_ACCESS_RW=y
-CONFIG_BAT7_ICACHE_INHIBITED=y
-CONFIG_BAT7_ICACHE_GUARDED=y
-CONFIG_BAT7_DCACHE_INHIBITED=y
-CONFIG_BAT7_DCACHE_GUARDED=y
-CONFIG_BAT7_USER_MODE_VALID=y
-CONFIG_BAT7_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0x80000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_1_GBYTES=y
-CONFIG_LBLAW1=y
-# CONFIG_LBLAW1_ENABLE is not set
-CONFIG_LBLAW2=y
-# CONFIG_LBLAW2_ENABLE is not set
-CONFIG_LBLAW3=y
-# CONFIG_LBLAW3_ENABLE is not set
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0x80000000
-CONFIG_BR0_PORTSIZE_32BIT=y
-CONFIG_OR0_AM_1_GBYTES=y
-CONFIG_OR0_SCY_5=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_QUARTER_CYCLE_EARLIER=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_8=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=6
-CONFIG_USE_PREBOOT=y
-CONFIG_PREBOOT="echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_JFFS2=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=TQM834x-0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=TQM834x-0:256k(u-boot),256k(env),1m(kernel),2m(initrd),-(user);"
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_ADDR=0x80060000
-CONFIG_ENV_ADDR_REDUND=0x80080000
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_EEPRO100=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-/*
- * TQM8349 board configuration file
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 Family */
-
-/* board pre init: do not call, nothing to do */
-
-/* detect the number of flash banks */
-
-/*
- * DDR Setup
- */
- /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define DDR_CASLAT_25 /* CASLAT set to 2.5 */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup */
-
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
-
-/*
- * FLASH on the Local Bus
- */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_BASE 0x80000000 /* start of FLASH */
-#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size in MB */
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sectors */
-
-/*
- * FLASH bank number detection
- */
-
-/*
- * When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is defined, the actual number of
- * Flash banks has to be determined at runtime and stored in a gloabl variable
- * tqm834x_num_flash_banks. The value of CONFIG_SYS_MAX_FLASH_BANKS_DETECT is
- * only used instead of CONFIG_SYS_MAX_FLASH_BANKS to allocate the array
- * flash_info, and should be made sufficiently large to accomodate the number
- * of banks that might actually be detected. Since most (all?) Flash related
- * functions use CONFIG_SYS_MAX_FLASH_BANKS as the number of actual banks on
- * the board, it is defined as tqm834x_num_flash_banks.
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2
-
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors per device */
-
-
-/* disable remaining mappings */
-#define CONFIG_SYS_BR1_PRELIM 0x00000000
-#define CONFIG_SYS_OR1_PRELIM 0x00000000
-
-#define CONFIG_SYS_BR2_PRELIM 0x00000000
-#define CONFIG_SYS_OR2_PRELIM 0x00000000
-
-#define CONFIG_SYS_BR3_PRELIM 0x00000000
-#define CONFIG_SYS_OR3_PRELIM 0x00000000
-
-/*
- * Monitor config
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#else
-# undef CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
- /* Reserve 384 kB = 3 sect. for Mon */
-#define CONFIG_SYS_MONITOR_LEN (384 * 1024)
- /* Reserve 512 kB for malloc */
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-
-/* I2C EEPROM, configuration for onboard EEPROMs 24C256 and 24C32 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16 bit */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32 bytes/write */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10ms +/- 20% */
-
-/* I2C RTC */
-#define CONFIG_RTC_DS1337 /* use ds1337 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-
-/*
- * TSEC
- */
-
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "TSEC1"
-#define TSEC1_PHY_ADDR 2
-#define TSEC2_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC2_FLAGS TSEC_GIGABIT
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME "TSEC0"
-
-#endif /* CONFIG_TSEC_ENET */
-
-#if defined(CONFIG_PCI)
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-
-/* PCI1 host bridge */
-#define CONFIG_SYS_PCI1_MEM_BASE 0x90000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE \
- (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
-#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE 0xe2000000
-#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
-#define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */
-
-
-#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BASE
- #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_MEM_BASE
- #define PCI_IDSEL_NUMBER 0x1c /* slot0 (IDSEL) = 28 */
-#endif
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
-
-#endif /* CONFIG_PCI */
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
- /* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
-
-/* System IO Config */
-#define CONFIG_SYS_SICRH 0
-#define CONFIG_SYS_SICRL SICRL_LDP_A
-
-/* PCI */
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
- /* default location for tftp and bootm */
-#define CONFIG_LOADADDR 400000
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=tqm834x\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addcons=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
- "flash_nfs_old=run nfsargs addip addcons;" \
- "bootm ${kernel_addr}\0" \
- "flash_nfs=run nfsargs addip addcons;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "flash_self_old=run ramargs addip addcons;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_self=run ramargs addip addcons;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "net_nfs_old=tftp 400000 ${bootfile};" \
- "run nfsargs addip addcons;bootm\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addcons; " \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "rootpath=/opt/eldk/ppc_6xx\0" \
- "bootfile=tqm834x/uImage\0" \
- "fdtfile=tqm834x/tqm834x.dtb\0" \
- "kernel_addr_r=400000\0" \
- "fdt_addr_r=600000\0" \
- "ramdisk_addr_r=800000\0" \
- "kernel_addr=800C0000\0" \
- "fdt_addr=800A0000\0" \
- "ramdisk_addr=80300000\0" \
- "u-boot=tqm834x/u-boot.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=protect off 80000000 +${filesize};" \
- "era 80000000 +${filesize};" \
- "cp.b 200000 80000000 ${filesize}\0" \
- "upd=run load update\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-/*
- * JFFS2 partitions
- */
-/* mtdparts command line support */
-
-/* default mtd partition table */
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff