Tom Rini [Thu, 4 Jan 2024 21:53:49 +0000 (16:53 -0500)]
Merge patch series "ATF and OP-TEE Firewalling for K3 devices."
Manorit Chawdhry <m-chawdhry@ti.com> says:
K3 devices have firewalls that are used to prevent illegal accesses to
memory regions that are deemed secure. The series prevents the illegal
accesses to ATF and OP-TEE regions that are present in different K3
devices.
AM62X, AM62AX and AM64X are currently in hold due to some firewall
configurations that our System Controller (TIFS) needs to handle.
The devices that are not configured with the firewalling nodes will not
be affected and can continue to work fine until the firewall nodes are
added so will be a non-blocking merge.
Test Logs: https://gist.github.com/manorit2001/4cead2fb3a19eb5d19005b3f54682627
CICD Run: https://github.com/u-boot/u-boot/pull/442
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com> Tested-by: Thomas Richard <thomas.richard@bootlin.com>
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Manorit Chawdhry [Fri, 29 Dec 2023 10:46:26 +0000 (16:16 +0530)]
binman: ti-secure: Add support for firewalling entities
We can now firewall entities while loading them through our secure
entity TIFS, the required information should be present in the
certificate that is being parsed by TIFS.
The following commit adds the support to enable the certificates to be
generated if the firewall configurations are present in the binman dtsi
nodes.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Manorit Chawdhry [Fri, 29 Dec 2023 10:46:25 +0000 (16:16 +0530)]
dtoc: Change dst to self in debug message
Fix the error message to not use dst and use self as it is copying the
properties to self.
While using templating if there are no subnodes defined, we end up in
this situation where "dst" isn't defined and it tries to print the error
message and fails.
'UnboundLocalError: local variable 'dst' referenced before assignment'
Fixes: 55e1278d5eca ("dtoc: Allow inserting a list of nodes into another") Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 3 Jan 2024 13:38:40 +0000 (08:38 -0500)]
Merge patch series "sync am65x device tree with Linux v6.7-rc1"
Bryan Brattlof <bb@ti.com> says:
Hello Again Everyone!
This series gets the am65x booting again along with syncing the device
tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64
files to make future syncs from Linux much easier. In the end the DTBs
should look a lot like what the DTBs look like for the am64x which
is fairly similar to the am65x.
Bryan Brattlof [Fri, 29 Dec 2023 17:47:23 +0000 (11:47 -0600)]
arm: dts: k3-am654: convert bootph-pre-ram to bootph-all
Many nodes are reused between WKUP SPL, MAIN SPL, and U-Boot. Using
bootph-pre-ram is causing these nodes to be present in SPL builds but
pruned away during the U-Boot build. Convert these nodes to bootph-all
so they will remain no matter which dtb build is happening.
Bryan Brattlof [Fri, 29 Dec 2023 17:47:09 +0000 (11:47 -0600)]
arm: dts: k3-am654: add needed regs to udmap nodes
Ethernet is one of a few IPs in U-Boot that depend on DMA to operate.
However there are a few missing registers ranges in the udmap nodes
need to properly setup DMA for the am65x.
A fix has been added to the Linux kernel[0] to add these ranges however
they have not made it to a Linux tag. To keep DMA operational until the
next DT sync from Linux, add these ranges to the *-u-boot.dtsi with a
note for our future selves.
Bryan Brattlof [Fri, 29 Dec 2023 17:47:06 +0000 (11:47 -0600)]
arm: dts: k3-am654: remove duplicate timer
timer1 is really just the mcu_timer0 node redefined for the WKUP SPL.
Remove the timer1 and replace it with the mcu_timer0 from the Linux
device tree we imported into U-Boot.
Bryan Brattlof [Fri, 29 Dec 2023 17:47:03 +0000 (11:47 -0600)]
arm: dts: k3-am654: include a53 board dtb for r5 build
To make things as organized as possible, start from the Linux board dtbs
and apply all properties needed for U-Boot in our *-u-boot.dtsi file for
the MAIN SPL and U-Boot builds.
We can then include these files for the WKUP SPL build making further
edits to the needed properties and nodes for the WKUP SPL bootloader's
view of the am65x.
Bryan Brattlof [Fri, 29 Dec 2023 17:47:02 +0000 (11:47 -0600)]
arm: dts: k3-am654: copy bootph properties to a53 dts
In order to unify the R5 board dtb file with the Linux board dtb file,
we will need to copy all bootph-pre-ram properties to the *-u-boot.dtsi
overlay.
Bryan Brattlof [Fri, 29 Dec 2023 17:46:59 +0000 (11:46 -0600)]
configs: am65x_evm_a53: disable CONSOLE_MUX
We do not have a need to share a single console with the evaluation
board and disabling this option reduces the complexity of configuring
the consoles. Disable CONSOLE_MUX
Simon Glass [Wed, 27 Dec 2023 21:07:10 +0000 (13:07 -0800)]
bloblist: Update documentation and header comment
Align the documentation with the v0.9 spec.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Wed, 27 Dec 2023 21:07:09 +0000 (13:07 -0800)]
bloblist: Add alignment to bloblist_new()
Allow the alignment to be specified when creating a bloblist.
Signed-off-by: Simon Glass <sjg@chromium.org> Co-developed-by: Raymond Mao <raymond.mao@linaro.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Wed, 27 Dec 2023 21:07:08 +0000 (13:07 -0800)]
bloblist: Adjust the bloblist header
The v0.9 spec provides for a 24-byte header. Update the implementation
to match this.
Rename the fields of the bloblist header to align to the spec.
Adds an alignment field into the bloblist header.
Update the related bloblist APIs and UT testcases.
Signed-off-by: Simon Glass <sjg@chromium.org> Co-developed-by: Raymond Mao <raymond.mao@linaro.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Wed, 27 Dec 2023 21:07:07 +0000 (13:07 -0800)]
bloblist: Reduce blob-header size
The v0.9 spec provides for an 8-byte header for each blob, with fewer
fields.
The blob data start address should be aligned to the alignment specified
by the bloblist header.
Update the implementation to match this.
Signed-off-by: Simon Glass <sjg@chromium.org> Co-developed-by: Raymond Mao <raymond.mao@linaro.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Simon Glass [Wed, 27 Dec 2023 21:07:06 +0000 (13:07 -0800)]
bloblist: Handle alignment with a void entry
Rather than setting the alignment using the header size, add an entirely
new entry to cover the gap left by the alignment.
Signed-off-by: Simon Glass <sjg@chromium.org> Co-developed-by: Raymond Mao <raymond.mao@linaro.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Wed, 27 Dec 2023 21:07:05 +0000 (13:07 -0800)]
bloblist: Checksum the entire bloblist
Use a sinple 8-bit checksum for bloblist, as specified by the spec
version 0.9.
Spec v0.9 specifies that the entire bloblist area is checksummed,
including unused portions. Update the code to follow this.
Signed-off-by: Simon Glass <sjg@chromium.org> Co-developed-by: Raymond Mao <raymond.mao@linaro.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Wed, 27 Dec 2023 21:07:04 +0000 (13:07 -0800)]
bloblist: Drop spare value from bloblist record
Drop spare value from bloblist record header.
For now it is still present in the header, with an underscore, so that
tests continue to pass.
Signed-off-by: Simon Glass <sjg@chromium.org> Co-developed-by: Raymond Mao <raymond.mao@linaro.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Simon Glass [Wed, 27 Dec 2023 21:07:03 +0000 (13:07 -0800)]
bloblist: Access record hdr_size and tag via a function
Convert accesses to tag and hdr_size via function for grouping tag and
hdr_size together later.
Signed-off-by: Simon Glass <sjg@chromium.org> Co-developed-by: Raymond Mao <raymond.mao@linaro.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Wed, 27 Dec 2023 21:07:02 +0000 (13:07 -0800)]
bloblist: Set version to 1
The new bloblist for v0.9 has version 1 so update this value.
Signed-off-by: Simon Glass <sjg@chromium.org> Co-developed-by: Raymond Mao <raymond.mao@linaro.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 27 Dec 2023 21:07:01 +0000 (13:07 -0800)]
bloblist: Change the magic value
This uses a new value with spec v0.9 so change it.
Signed-off-by: Simon Glass <sjg@chromium.org> Co-developed-by: Raymond Mao <raymond.mao@linaro.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 27 Dec 2023 21:07:00 +0000 (13:07 -0800)]
bloblist: Adjust API to align in powers of 2
The updated bloblist structure stores the alignment as a power-of-two
value in its structures. Adjust the API to use this, to avoid needing to
calling ilog2().
Update the bloblist alignment from 16 bytes to 8 bytes.
Drop a stale comment while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org> Co-developed-by: Raymond Mao <raymond.mao@linaro.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Wed, 27 Dec 2023 21:06:59 +0000 (13:06 -0800)]
bloblist: Update the tag numbering
Align bloblist tags with the FW handoff spec v0.9.
The most common ones are from 0.
TF related ones are from 0x100.
All non-standard ones from 0xfff000.
Added new defined tags:
BLOBLISTT_OPTEE_PAGABLE_PART for TF.
BLOBLISTT_TPM_EVLOG and BLOBLISTT_TPM_CRB_BASE for TPM.
Signed-off-by: Simon Glass <sjg@chromium.org> Co-developed-by: Raymond Mao <raymond.mao@linaro.org> Signed-off-by: Raymond Mao <raymond.mao@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simon Glass [Tue, 19 Dec 2023 14:21:25 +0000 (07:21 -0700)]
Makefile: Use the fdtgrep -u flag
Use this flag so that the bootph binding is obeyed correctly.
Add a comment about what is going on.
Signed-off-by: Simon Glass <sjg@chromium.org> Fixes: https://source.denx.de/u-boot/custodians/u-boot-dm/-/issues/12 Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sun, 17 Dec 2023 16:36:20 +0000 (09:36 -0700)]
fdtgrep: Move property checking into a function
The h_include() function includes a piece which checks if a node
contains a property being searched for. Move this into its own
function to reduce the size of the h_include() function.
Tom Rini [Thu, 28 Dec 2023 17:03:25 +0000 (12:03 -0500)]
Merge patch series "Modernize U-Boot shell"
Francis Laniel <francis.laniel@amarulasolutions.com> says:
During 2021 summer, Sean Anderson wrote a contribution to add a new shell, based
on LIL, to U-Boot [1, 2].
While one of the goals of this contribution was to address the fact actual
U-Boot shell, which is based on Busybox hush, is old there was a discussion
about adding a new shell versus updating the actual one [3, 4].
So, in this series, with Harald Seiler, we updated the actual U-Boot shell to
reflect what is currently in Busybox source code.
Basically, this contribution is about taking a snapshot of Busybox shell/hush.c
file (as it exists in commit 37460f5da) and adapt it to suit U-Boot needs.
This contribution was written to be as backward-compatible as possible to avoid
breaking the existing.
So, the modern hush flavor offers the same as the actual, that is to say:
1. Variable expansion.
2. Instruction lists (;, && and ||).
3. If, then and else.
4. Loops (for, while and until).
No new features offered by Busybox hush were implemented (e.g. functions).
It is possible to change the parser at runtime using the "cli" command:
=> cli print
old
=> cli set modern
=> cli print
modern
=> cli set old
The default parser is the old one.
Note that to use both parser, you would need to set both
CONFIG_HUSH_MODERN_PARSER and CONFIG_HUSH_OLD_PARSER.
In terms of testing, new unit tests were added to ut to ensure the new behavior
is the same as the old one and it does not add regression.
Nonetheless, if old behavior was buggy and fixed upstream, the fix is then added
to U-Boot [5].
In sandbox, all of these tests pass smoothly:
=> printenv board
board=sandbox
=> ut hush
Running 20 hush tests
...
Failures: 0
=> cli set modern
=> ut hush
Running 20 hush tests
...
Failures: 0
Thanks to the effort of Harald Seiler, I was successful booting a board:
=> printenv fdtfile
fdtfile=amlogic/meson-gxl-s905x-libretech-cc.dtb
=> cli get
old
=> boot
...
root@lepotato:~#
root@lepotato:~# reboot
...
=> cli set modern
=> cli get
modern
=> printenv fdtfile
fdtfile=amlogic/meson-gxl-s905x-libretech-cc.dtb
=> boot
...
root@lepotato:~#
This contribution indeed adds a lot of code and there were concern about its
size [6, 7].
With regard to the amount of code added, the cli_hush_upstream.c is 13030 lines
long but it seems a smaller subset is really used:
gcc -D__U_BOOT__ -E common/cli_hush_upstream.c | wc -l
2870
Despite this, it is better to still have the whole upstream code for the sake of
easing maintenance.
With regard to memory size, I conducted some experiments for version 8 of this
series and for a subset of arm64 boards and found the worst case to be 4K [8].
Tom Rini conducted more research on this and also found the increase to be
acceptable [9].
If you want to review it - your review will really be appreciated - here are
some information regarding the commits:
* commits marked as "test:" deal with unit tests.
* commit "cli: Add Busybox upstream hush.c file." copies Busybox shell/hush.c
into U-Boot tree, this explain why this commit contains around 12000 additions.
* commit "cli: Port Busybox 2021 hush to U-Boot." modifies previously added file
to permit us to use this as new shell.
The really good idea of #include'ing Busybox code into a wrapper file to define
some particular functions while minimizing modifications to upstream code comes
from Harald Seiler.
* commit "cmd: Add new parser command" adds a new command which permits
selecting parser at runtime.
I am not really satisfied with the fact it calls cli_init() and cli_loop() each
time the parser is set, so your reviews would be welcomed.
* Other commits focus on enabling features we need (e.g. if).
Francis Laniel [Fri, 22 Dec 2023 21:02:44 +0000 (22:02 +0100)]
configs: Use old hush for several boards
The keymile board family is not compatible with modern hush parser.
Indeed, This boards used set_local_var() to store some variables as local shell.
They then used get_local_var() to retrieve the variables values.
Sadly, this two functions do not exist with CONFIG_HUSH_MODERN_PARSER.
A patch was proposed to use environment variables rather than local variables
but it does not tackle the problem, so complementary work is needed to make
this boards use CONFIG_HUSH_MODERN_PARSER.
Also, with CONFIG_HUSH_MODERN_PARSER, kirkwoord sheevaplug and phytec bk4r1 hit
their board limits, so better to stick with old hush.
Francis Laniel [Fri, 22 Dec 2023 21:02:42 +0000 (22:02 +0100)]
cli: modern_hush: Add upstream commits up to 2nd October 2023.
This commit adds the following hush busybox upstream commits: 791b222dd55d ("sleep: fix "sleep -- ARGS"") 5353df91cba7 ("Update applet size estimates") e41e481fd571 ("hush: fix a compile failure") 07a95cfcabb0 ("ash: disable check for "good" function name, bash does not check this") e5692e2342c6 ("hush: quote values in "readonly" output") 96769486e20f ("shell: move varcmp() to shell_common.h and use it in hush") bab8828b0dad ("hush: fix expansion of space in "a=${a:+$a }c" construct") b5be8da350b5 ("hush: make "false" built-in") 6824298ab4d3 ("hush: fix ELIF cmd1;cmd2 THEN ... not executing cmd2, closes 15571") 3a7f00eadcf4 ("hush: add comment about abort on syntax error %{^}") acae889dd972 ("ash,hush: tab completion of functions and aliases") 90b607d79a13 ("hush: quote variable values printed by "set" (match ash behavior)") 6748e6494c22 ("hush (NOMMU): fix LINENO in execed children") fd5fb2d2b596 ("hush: speed up "big heredoc" code") 1409432d072e ("hush: add TODO comment") 93ae7464e6e4 ("hush: restore SIGHUP handling, this time explain why we do what we do") 1fdb33bd07e5 ("hush: restore tty pgrp on SIGHUP") 6101b6d3eaa0 ("hush: remove special handling of SIGHUP") 93e0898c663a ("shell: fix SIGWINCH and SIGCHLD (in hush) interrupting line input, closes 15256") 969e00816835 ("hush: code shrink") 27be0e8cfeb6 ("shell: fix compile failures in some configs") 7d1c7d833785 ("ash,hush: use HOME for tab completion and prompts") 21afddefd258 ("hush: fix "error: invalid preprocessing directive ##"") e53c7dbafc78 ("hush: fix set -n to act immediately, not just after run_list()") 574b9c446da1 ("hush: fix var_LINENO3.tests failure") 49bcf9f40cff ("hush: speed up ${x//\*/|} too") 53b2fdcdba4c ("*: add NOINLINEs where code noticeably shrinks") 7c3e96d4b3d4 ("shell: use more compact SHELL_ASH / HUSH config defines. no code changes") 62f1eed1e191 ("hush: in a comment, document what -i might be doing") aaf3d5ba74c5 ("shell: tweak --help") db5546ca1018 ("libbb: code shrink: introduce and use [_]exit_SUCCESS()") 931c55f9e2b4 ("libbb: invert the meaning of SETUP_ENV_NO_CHDIR -> SETUP_ENV_CHDIR") 12566e7f9b5e ("ash,hush: fix handling of SIGINT while waiting for interactive input") 987be932ed3c ("*: slap on a few ALIGN_PTR where appropriate")
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com>
Francis Laniel [Fri, 22 Dec 2023 21:02:38 +0000 (22:02 +0100)]
cli: hush_modern: Enable using < and > as string compare operators
In Busybox hush, '<' and '>' are used as redirection operators.
For example, cat foo > bar will write content of file foo inside file bar.
In U-Boot, we do not have file system, so we can hardly redirect command output
inside a file.
But, in actual U-Boot hush, these operators ('<' and '>') are used as string
compare operators.
For example, test aaa < bbb returns 0 as aaa is before bbb in the dictionary.
Busybox hush also permits this, but operators need to be escaped ('\<' and
'\>').
Indeed, if escaping is needed it permits the developer to think about its code,
as in a lot of case, we want to compare integers (using '-lt' or '-gt') rather
than strings.
As testing in U-Boot is handled by the test command, we will stick with the
original behaviour and not adapt to Busybox one.
Nonetheless, if one day we decide to implement test with '[[ ]]', we will then
stick to upstream Busybox behavior.
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Francis Laniel [Fri, 22 Dec 2023 21:02:37 +0000 (22:02 +0100)]
test: hush: Fix variable expansion tests for modern hush
Modifies the expected result for modern hush.
Indeed, there were bugs in actual U-Boot hush which were fixed in upstream
Busybox.
As modern hush is based on upstream Busybox, these bugs no longer exist.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com>
Francis Laniel [Fri, 22 Dec 2023 21:02:36 +0000 (22:02 +0100)]
test: hush: Fix instructions list tests for modern hush
Modifies the expected result for modern hush.
Indeed, there were bugs in actual U-Boot hush which were fixed in upstream
Busybox.
As modern hush is based on upstream Busybox, these bugs no longer exist.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com>
Francis Laniel [Fri, 22 Dec 2023 21:02:34 +0000 (22:02 +0100)]
cli: hush_modern: Add functions to be called from run_command()
run_command() is called internally by the command run and it can also be called
directly from U-Boot code, e.g. to do unit tests.
This commit adds this path to go to modern hush.
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Francis Laniel [Fri, 22 Dec 2023 21:02:33 +0000 (22:02 +0100)]
cli: hush_modern: Enable variables expansion for modern hush
Enables variables expansion for modern hush, both for local and environment
variables.
So the following commands:
foo=bar
echo $foo
setenv bar foo
echo $bar
leads to "bar" and "foo" being printed on console output.
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Francis Laniel [Fri, 22 Dec 2023 21:02:31 +0000 (22:02 +0100)]
cmd: Add new cli command
This command can be used to print the current parser with 'cli get'.
It can also be used to set the current parser with 'cli set'.
For the moment, only one value is valid for set: old.
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com>
Francis Laniel [Fri, 22 Dec 2023 21:02:29 +0000 (22:02 +0100)]
cli: Add menu for hush parser
For the moment, the menu contains only entry: HUSH_OLD_PARSER which is the
default.
The goal is to prepare the field to add a new hush parser which guarantees
actual behavior is still correct.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com>
Francis Laniel [Fri, 22 Dec 2023 21:02:28 +0000 (22:02 +0100)]
cli: Port upstream Busybox hush to U-Boot
Adds new file cli_hush_upstream.c, it is a copy of Busybox hush file as it was of
time to commit 37460f5da.
This commit modifies Busybox hush to not compile some part specific to Busybox
and adds some code needed by U-Boot.
The modifications consists mainly on adding code #if(n)def guards.
For the moment, this refurbished flavor of hush only permits running command
without any keywords (i.e., if and for are not recognized) or variable expansion
(i.e., echo $foo prints foo and not value stored in variable foo).
A new file was also added to define some functions specific to U-Boot.
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com> Signed-off-by: Harald Seiler <hws@denx.de>
Francis Laniel [Fri, 22 Dec 2023 21:02:22 +0000 (22:02 +0100)]
test: hush: Test hush if/else
As asked in commit 9c6bf1715f6a ("test/py: hush_if_test: Add tests to cover
octal/hex values"), this commit translates test_hush_if_test.py to a C test.
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log