From: Fabio Estevam Date: Sat, 14 Sep 2024 00:56:05 +0000 (-0300) Subject: imx6q-lxr: Add board support X-Git-Url: http://git.dujemihanovic.xyz/contact?a=commitdiff_plain;h=effe934e50f03c92ba6febecfe132c9cb34ecf59;p=u-boot.git imx6q-lxr: Add board support Add support for the Comvetia i.MX6Q LXR2 board, which is uses the Phytec PFLA02 SoM. Based on the original work from Stefano Babic . The Phytec PFLA02 devicetrees are taken from kernel 6.11-rc7. The imx6q-lxr.dts has been submitted upstream: https://lore.kernel.org/linux-devicetree/20240913200906.1753458-3-festevam@gmail.com/ After it gets accepted in mainline (most likely in kernel 6.13), the lxr2 board can then be switched to OF_UPSTREAM and these device trees can be removed from U-Boot. Signed-off-by: Fabio Estevam --- diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 56d4af518d..05a00e4435 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -812,6 +812,7 @@ dtb-y += \ imx6q-icore-rqs.dtb \ imx6q-kp.dtb \ imx6q-logicpd.dtb \ + imx6q-lxr.dtb \ imx6q-marsboard.dtb \ imx6q-mccmon6.dtb\ imx6q-nitrogen6x.dtb \ diff --git a/arch/arm/dts/imx6q-lxr.dts b/arch/arm/dts/imx6q-lxr.dts new file mode 100644 index 0000000000..ae4f8eeb10 --- /dev/null +++ b/arch/arm/dts/imx6q-lxr.dts @@ -0,0 +1,87 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// +// Copyright 2024 Comvetia AG + +/dts-v1/; +#include "imx6q-phytec-pfla02.dtsi" + +/ { + model = "COMVETIA QSoIP LXR-2"; + compatible = "comvetia,imx6q-lxr", "phytec,imx6q-pfla02", "fsl,imx6q"; + + chosen { + stdout-path = &uart4; + }; + + spi { + compatible = "spi-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi_gpio>; + sck-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>; + num-chipselects = <0>; + #address-cells = <1>; + #size-cells = <0>; + + fpga@0 { + compatible = "altr,fpga-passive-serial"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fpga>; + nconfig-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>; + nstat-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>; + confd-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&ecspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3>; + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + }; +}; + +&fec { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&usdhc3 { + no-1-8-v; + status = "okay"; +}; + +&iomuxc { + pinctrl_fpga: fpgagrp { + fsl,pins = < + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0 + MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0 + MX6QDL_PAD_DI0_PIN3__GPIO4_IO19 0x1b0b0 + >; + }; + + pinctrl_spi_gpio: spigpiogrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1b0b0 + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b0 + >; + }; +}; diff --git a/arch/arm/dts/imx6q-phytec-pfla02.dtsi b/arch/arm/dts/imx6q-phytec-pfla02.dtsi new file mode 100644 index 0000000000..500944bd2a --- /dev/null +++ b/arch/arm/dts/imx6q-phytec-pfla02.dtsi @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright 2013 Christian Hemp, Phytec Messtechnik GmbH + */ + +#include "imx6q.dtsi" +#include "imx6qdl-phytec-pfla02.dtsi" + +/ { + model = "Phytec phyFLEX-i.MX6 Quad"; + compatible = "phytec,imx6q-pfla02", "fsl,imx6q"; + + memory@10000000 { + device_type = "memory"; + reg = <0x10000000 0x80000000>; + }; +}; diff --git a/arch/arm/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/dts/imx6qdl-phytec-pfla02.dtsi new file mode 100644 index 0000000000..c0c47adc58 --- /dev/null +++ b/arch/arm/dts/imx6qdl-phytec-pfla02.dtsi @@ -0,0 +1,467 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright 2013 Christian Hemp, Phytec Messtechnik GmbH + */ + +#include + +/ { + model = "Phytec phyFLEX-i.MX6 Quad"; + compatible = "phytec,imx6q-pfla02", "fsl,imx6q"; + + memory@10000000 { + device_type = "memory"; + reg = <0x10000000 0x80000000>; + }; + + reg_usb_otg_vbus: regulator-usb-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio4 15 0>; + enable-active-high; + }; + + reg_usb_h1_vbus: regulator-usb-h1-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1_vbus>; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 0 0>; + enable-active-high; + }; + + gpio_leds: leds { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + compatible = "gpio-leds"; + + led_green: led-green { + label = "phyflex:green"; + gpios = <&gpio1 30 0>; + }; + + led_red: led-red { + label = "phyflex:red"; + gpios = <&gpio2 31 0>; + }; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "disabled"; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + status = "disabled"; +}; + +&ecspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3>; + status = "okay"; + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>; + + som_flash: flash@0 { + compatible = "m25p80", "jedec,spi-nor"; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-handle = <ðphy>; + phy-mode = "rgmii"; + phy-reset-duration = <10>; /* in msecs */ + phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>; + phy-supply = <&vdd_eth_io_reg>; + status = "disabled"; + + fec_mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + txc-skew-ps = <1680>; + rxc-skew-ps = <1860>; + }; + }; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + nand-on-flash-bbt; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + som_eeprom: eeprom@50 { + compatible = "catalyst,24c32", "atmel,24c32"; + pagesize = <32>; + reg = <0x50>; + }; + + pmic@58 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + compatible = "dlg,da9063"; + reg = <0x58>; + interrupt-parent = <&gpio2>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; /* active-low GPIO2_9 */ + #interrupt-cells = <2>; + interrupt-controller; + + regulators { + vddcore_reg: bcore1 { + regulator-min-microvolt = <730000>; + regulator-max-microvolt = <1380000>; + regulator-always-on; + }; + + vddsoc_reg: bcore2 { + regulator-min-microvolt = <730000>; + regulator-max-microvolt = <1380000>; + regulator-always-on; + }; + + vdd_ddr3_reg: bpro { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + }; + + vdd_3v3_reg: bperi { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_buckmem_reg: bmem { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_eth_reg: bio { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + vdd_eth_io_reg: ldo4 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + vdd_mx6_snvs_reg: ldo5 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + vdd_3v3_pmic_io_reg: ldo6 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_sd0_reg: ldo9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vdd_sd1_reg: ldo10 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vdd_mx6_high_reg: ldo11 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + }; + + da9063_rtc: rtc { + compatible = "dlg,da9063-rtc"; + }; + + da9063_wdog: watchdog { + compatible = "dlg,da9063-watchdog"; + }; + + onkey { + compatible = "dlg,da9063-onkey"; + status = "disabled"; + }; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clock-frequency = <100000>; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clock-frequency = <100000>; +}; + +&iomuxc { + imx6q-phytec-pfla02 { + pinctrl_ecspi3: ecspi3grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000 /* CS0 */ + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000 /* Reset GPIO */ + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b0b0 + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b0 + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x80000000 /* Green LED */ + MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x80000000 /* Red LED */ + >; + }; + + pinctrl_pcie: pciegrp { + fsl,pins = ; + }; + + pinctrl_pmic: pmicgrp { + fsl,pins = ; /* PMIC interrupt */ + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1 + MX6QDL_PAD_EIM_D30__UART3_CTS_B 0x1b0b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbh1_vbus: usbh1vbusgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0 + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x80000000 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + + pinctrl_usdhc3_cdwp: usdhc3cdwp { + fsl,pins = < + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x80000000 + MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 + >; + }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT16__AUD5_TXC 0x130b0 + MX6QDL_PAD_DISP0_DAT17__AUD5_TXD 0x110b0 + MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS 0x130b0 + MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0 + >; + }; + }; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie>; + reset-gpio = <&gpio4 17 GPIO_ACTIVE_LOW>; + status = "disabled"; +}; + +®_arm { + vin-supply = <&vddcore_reg>; +}; + +®_pu { + vin-supply = <&vddsoc_reg>; +}; + +®_soc { + vin-supply = <&vddsoc_reg>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + uart-has-rtscts; + status = "disabled"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "disabled"; +}; + +&usbh1 { + vbus-supply = <®_usb_h1_vbus>; + status = "disabled"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "disabled"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + vmmc-supply = <&vdd_sd1_reg>; + status = "disabled"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3 + &pinctrl_usdhc3_cdwp>; + cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>; + vmmc-supply = <&vdd_sd0_reg>; + status = "disabled"; +}; + +&wdog1 { + /* + * Rely on PMIC reboot handler. Internal i.MX6 watchdog, that is also + * used for reboot, does not reset all external PMIC voltages on reset. + */ + status = "disabled"; +}; diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig index 7a56767225..1f8022ee68 100644 --- a/arch/arm/mach-imx/mx6/Kconfig +++ b/arch/arm/mach-imx/mx6/Kconfig @@ -541,6 +541,16 @@ config TARGET_LITEBOARD select BOARD_LATE_INIT select MX6UL_LITESOM +config TARGET_LXR2 + bool "Comvetia i.MX6Q LXR2" + depends on MX6Q + select BOARD_EARLY_INIT_F + select BOARD_LATE_INIT + select DM + select DM_THERMAL + select SUPPORT_SPL + imply CMD_DM + config TARGET_PCM058 bool "Phytec PCM058 i.MX6 Quad" depends on MX6Q @@ -696,6 +706,7 @@ source "board/boundary/nitrogen6x/Kconfig" source "board/bsh/imx6ulz_smm_m2/Kconfig" source "board/bticino/mamoj/Kconfig" source "board/compulab/cm_fx6/Kconfig" +source "board/comvetia/lxr2/Kconfig" source "board/dhelectronics/dh_imx6/Kconfig" source "board/embest/mx6boards/Kconfig" source "board/engicam/imx6q/Kconfig" diff --git a/board/comvetia/lxr2/Kconfig b/board/comvetia/lxr2/Kconfig new file mode 100644 index 0000000000..93c7f49071 --- /dev/null +++ b/board/comvetia/lxr2/Kconfig @@ -0,0 +1,12 @@ +if TARGET_LXR2 + +config SYS_BOARD + default "lxr2" + +config SYS_VENDOR + default "comvetia" + +config SYS_CONFIG_NAME + default "lxr2" + +endif diff --git a/board/comvetia/lxr2/MAINTAINERS b/board/comvetia/lxr2/MAINTAINERS new file mode 100644 index 0000000000..25db90bb79 --- /dev/null +++ b/board/comvetia/lxr2/MAINTAINERS @@ -0,0 +1,6 @@ +COMVETIA LXR2 +M: Fabio Estevam +S: Maintained +F: board/comvetia/lxr2/ +F: include/configs/lxr2.h +F: configs/lxr2_defconfig diff --git a/board/comvetia/lxr2/Makefile b/board/comvetia/lxr2/Makefile new file mode 100644 index 0000000000..86b9284521 --- /dev/null +++ b/board/comvetia/lxr2/Makefile @@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0+ + +obj-y := lxr2.o diff --git a/board/comvetia/lxr2/lxr2.c b/board/comvetia/lxr2/lxr2.c new file mode 100644 index 0000000000..173263522b --- /dev/null +++ b/board/comvetia/lxr2/lxr2.c @@ -0,0 +1,388 @@ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright (C) 2017 Stefano Babic +// Copyright (C) 2024 Fabio Estevam + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ + PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + +#define NAND_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + +int dram_init(void) +{ + gd->ram_size = imx_ddr_size(); + return 0; +} + +static const iomux_v3_cfg_t uart4_pads[] = { + MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads)); +} + +static void setup_gpmi_nand(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + /* gate ENFC_CLK_ROOT clock first,before clk source switch */ + clrbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK); + + /* config gpmi and bch clock to 100 MHz */ + clrsetbits_le32(&mxc_ccm->cs2cdr, + MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK | + MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK | + MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK, + MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) | + MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) | + MXC_CCM_CS2CDR_ENFC_CLK_SEL(3)); + + /* enable ENFC_CLK_ROOT clock */ + setbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK); + + /* enable gpmi and bch clock gating */ + setbits_le32(&mxc_ccm->CCGR4, + MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK | + MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK | + MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK | + MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK | + MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET); + + /* enable apbh clock gating */ + setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK); +} + +int board_spi_cs_gpio(unsigned int bus, unsigned int cs) +{ + return IMX_GPIO_NR(4, 24); +} + +int board_early_init_f(void) +{ + setup_iomux_uart(); + + return 0; +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + + setup_gpmi_nand(); + + return 0; +} + +/* + * BOOT_CFG1, BOOT_CFG2, BOOT_CFG3, BOOT_CFG4 + * see Table 8-11 and Table 5-9 + * BOOT_CFG1[7] = 1 (boot from NAND) + * BOOT_CFG1[5] = 0 - raw NAND + * BOOT_CFG1[4] = 0 - default pad settings + * BOOT_CFG1[3:2] = 00 - devices = 1 + * BOOT_CFG1[1:0] = 00 - Row Address Cycles = 3 + * BOOT_CFG2[4:3] = 00 - Boot Search Count = 2 + * BOOT_CFG2[2:1] = 01 - Pages In Block = 64 + * BOOT_CFG2[0] = 0 - Reset time 12ms + */ +static const struct boot_mode board_boot_modes[] = { + /* NAND: 64pages per block, 3 row addr cycles, 2 copies of FCB/DBBT */ + {"nand", MAKE_CFGVAL(0x80, 0x02, 0x00, 0x00)}, + {"mmc0", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)}, + {NULL, 0}, +}; + +int board_late_init(void) +{ + add_board_boot_modes(board_boot_modes); + + return 0; +} + +#ifdef CONFIG_SPL_BUILD +#include + +#define MX6_PHYFLEX_ERR006282 IMX_GPIO_NR(2, 11) +static void phyflex_err006282_workaround(void) +{ + /* + * Boards beginning with 1362.2 have the SD4_DAT3 pin connected + * to the CMIC. If this pin isn't toggled within 10s the boards + * reset. The pin is unconnected on older boards, so we do not + * need a check for older boards before applying this fixup. + */ + + gpio_request(MX6_PHYFLEX_ERR006282, "errata_gpio"); + gpio_direction_output(MX6_PHYFLEX_ERR006282, 0); + mdelay(2); + gpio_direction_output(MX6_PHYFLEX_ERR006282, 1); + mdelay(2); + gpio_set_value(MX6_PHYFLEX_ERR006282, 0); + + imx_iomux_v3_setup_pad(MX6_PAD_SD4_DAT3__GPIO2_IO11); + + gpio_direction_input(MX6_PHYFLEX_ERR006282); +} + +static const iomux_v3_cfg_t gpios_pads[] = { + MX6_PAD_SD4_DAT3__GPIO2_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_SD4_DAT4__GPIO2_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_SD4_DAT5__GPIO2_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_SD4_DAT6__GPIO2_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_SD4_DAT7__GPIO2_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_EIM_EB3__GPIO2_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_ENET_TXD0__GPIO1_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static void setup_gpios(void) +{ + imx_iomux_v3_setup_multiple_pads(gpios_pads, ARRAY_SIZE(gpios_pads)); +} + +static const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = { + .dram_sdclk_0 = 0x00000030, + .dram_sdclk_1 = 0x00000030, + .dram_cas = 0x00000030, + .dram_ras = 0x00000030, + .dram_reset = 0x00000030, + .dram_sdcke0 = 0x00003000, + .dram_sdcke1 = 0x00003000, + .dram_sdba2 = 0x00000030, + .dram_sdodt0 = 0x00000030, + .dram_sdodt1 = 0x00000030, + + .dram_sdqs0 = 0x00000028, + .dram_sdqs1 = 0x00000028, + .dram_sdqs2 = 0x00000028, + .dram_sdqs3 = 0x00000028, + .dram_sdqs4 = 0x00000028, + .dram_sdqs5 = 0x00000028, + .dram_sdqs6 = 0x00000028, + .dram_sdqs7 = 0x00000028, + .dram_dqm0 = 0x00000028, + .dram_dqm1 = 0x00000028, + .dram_dqm2 = 0x00000028, + .dram_dqm3 = 0x00000028, + .dram_dqm4 = 0x00000028, + .dram_dqm5 = 0x00000028, + .dram_dqm6 = 0x00000028, + .dram_dqm7 = 0x00000028, +}; + +static const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = { + .grp_ddr_type = 0x000C0000, + .grp_ddrmode_ctl = 0x00020000, + .grp_ddrpke = 0x00000000, + .grp_addds = 0x30, + .grp_ctlds = 0x30, + .grp_ddrmode = 0x00020000, + .grp_b0ds = 0x00000028, + .grp_b1ds = 0x00000028, + .grp_b2ds = 0x00000028, + .grp_b3ds = 0x00000028, + .grp_b4ds = 0x00000028, + .grp_b5ds = 0x00000028, + .grp_b6ds = 0x00000028, + .grp_b7ds = 0x00000028, +}; + +static const struct mx6_mmdc_calibration mx6_mmcd_calib = { + .p0_mpwldectrl0 = 0x00170018, + .p0_mpwldectrl1 = 0x003B0039, + .p1_mpwldectrl0 = 0x00350048, + .p1_mpwldectrl1 = 0x00410052, + .p0_mpdgctrl0 = 0x03600374, + .p0_mpdgctrl1 = 0x03680360, + .p1_mpdgctrl0 = 0x0370037C, + .p1_mpdgctrl1 = 0x03700350, + .p0_mprddlctl = 0x3A363234, + .p1_mprddlctl = 0x3634363C, + .p0_mpwrdlctl = 0x38383E3C, + .p1_mpwrdlctl = 0x422A483C, +}; + +/* MT41K64M16JT-125 (1Gb density) */ +static struct mx6_ddr3_cfg mem_ddr = { + .mem_speed = 1600, + .density = 1, + .width = 16, + .banks = 8, + .rowaddr = 13, + .coladdr = 10, + .pagesz = 2, + .trcd = 1375, + .trcmin = 4875, + .trasmin = 3500, + .SRT = 1, +}; + +static void ccgr_init(void) +{ + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + writel(0x00C03F3F, &ccm->CCGR0); + writel(0x0030FC03, &ccm->CCGR1); + writel(0x0FFFC000, &ccm->CCGR2); + writel(0x3FF00000, &ccm->CCGR3); + writel(0x00FFF300, &ccm->CCGR4); + writel(0x0F0000C3, &ccm->CCGR5); + writel(0x000003FF, &ccm->CCGR6); +} + +static void spl_dram_init(void) +{ + struct mx6_ddr_sysinfo sysinfo = { + .dsize = 2, + .cs_density = 6, + .ncs = 2, + .cs1_mirror = 1, + .rtt_wr = 1, + .rtt_nom = 1, + .walat = 1, + .ralat = 5, + .mif3_mode = 3, + .bi_on = 1, + .sde_to_rst = 0x10, + .rst_to_cke = 0x23, + .ddr_type = DDR_TYPE_DDR3, + .refsel = 1, + .refr = 7, + }; + + mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs); + mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr); +} + +#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ + PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ + PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +struct fsl_esdhc_cfg usdhc_cfg[1] = { + {USDHC3_BASE_ADDR}, +}; + +static const iomux_v3_cfg_t usdhc3_pads[] = { + MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), +}; + +int board_mmc_init(struct bd_info *bis) +{ + imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); + usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR; + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + usdhc_cfg[0].max_bus_width = 4; + gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; + + return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); +} + +void board_boot_order(u32 *spl_boot_list) +{ + spl_boot_list[0] = spl_boot_device(); + + switch (spl_boot_list[0]) { + case BOOT_DEVICE_SPI: + spl_boot_list[1] = BOOT_DEVICE_UART; + break; + case BOOT_DEVICE_MMC1: + spl_boot_list[1] = BOOT_DEVICE_SPI; + spl_boot_list[2] = BOOT_DEVICE_UART; + break; + default: + printf("Boot device %x\n", spl_boot_list[0]); + } +} + +static const iomux_v3_cfg_t ecspi3_pads[] = { + MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_DISP0_DAT3__GPIO4_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static void setup_spi(void) +{ + imx_iomux_v3_setup_multiple_pads(ecspi3_pads, ARRAY_SIZE(ecspi3_pads)); + + enable_spi_clk(true, 2); +} + +void board_init_f(ulong dummy) +{ + /* setup clock gating */ + ccgr_init(); + + /* setup AIPS and disable watchdog */ + arch_cpu_init(); + + /* setup AXI */ + gpr_init(); + + board_early_init_f(); + + /* setup GP timer */ + timer_init(); + + /* UART clocks enabled and gd valid - init serial console */ + preloader_console_init(); + + setup_spi(); + + setup_gpios(); + + /* DDR initialization */ + spl_dram_init(); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + phyflex_err006282_workaround(); + + /* load/boot image from boot device */ + board_init_r(NULL, 0); +} +#endif diff --git a/board/comvetia/lxr2/lxr2.env b/board/comvetia/lxr2/lxr2.env new file mode 100644 index 0000000000..ec21380022 --- /dev/null +++ b/board/comvetia/lxr2/lxr2.env @@ -0,0 +1,34 @@ +addcons=setenv bootargs ${bootargs} console=${console},${baudrate} +addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off +addmisc=setenv bootargs ${bootargs} ${miscargs} +addmtd=run mtdnand;run mtdspi;setenv bootargs ${bootargs} ${mtdparts} +altbootcmd=run swupdate +bootcmd=run nandboot;run swupdate +bootcount=2 +bootlimit=3 +console=ttymxc3 +cpu=armv7 +ethprime=FEC +fdt_addr_r=0x18000000 +fitfile=fitImage +flash-all-from-sd-card=env default -f -a;load mmc 0:1 10000000 u-boot.scr;source 10000000;saveenv +initrd_high=0xffffffff +kernel_addr_r=0x12000000 +loadaddr=0x12000000 +miscargs=panic=1 +mmcargs=setenv bootargs root=${mmcroot} rw rootwait +mmcboot=if run mmcload;then run mmcargs addcons addmisc;bootm;fi +mmcload=mmc rescan;load mmc 0:${mmcpart} ${kernel_addr_r} boot/fitImage +mmcpart=1 +mmcroot=/dev/mmcblk0p1 +mtdnand=setenv mtdparts mtdparts=gpmi-nand:40m(Kernels),860m(root),-(nand) +mtdspi=setenv mtdparts ${mtdparts}';spi2.0:1024k(bootloader),64k(env1),64k(env2),-(rescue)' +nanboot_fit=tftp ${kernel_addr_r} ${board_name}/${fitfile};run nandargs addip addcons addmtd addmisc;bootm +nandargs=setenv bootargs ubi.mtd=1 root=ubi0:rootfs${ubiroot} rootfstype=ubifs +nandboot=run mtdnand;ubi part Kernels;ubi readvol ${kernel_addr_r} kernel${ubiroot};run nandargs addip addcons addmtd addmisc;bootm ${kernel_addr_r} +net_nfs=tftp ${kernel_addr_r} ${board_name}/${bootfile};tftp ${fdt_addr_r} ${board_name}/${fdt_file};run nfsargs addip addcons addmtd addmisc;bootm ${kernel_addr_r} - ${fdt_addr_r} +net_nfs_fit=tftp ${kernel_addr_r} ${board_name}/${fitfile};run nfsargs addip addcons addmtd addmisc;bootm ${kernel_addr_r} +netmask=255.255.255.0 +nfsargs=setenv bootargs root=/dev/nfs nfsroot=${serverip}:${nfsroot},v3 panic=1 +swupdate=setenv bootargs root=/dev/ram;run addip addcons addmtd addmisc;sf probe;sf read ${kernel_addr_r} 120000 600000;sf read 14000000 730000 800000;bootm ${kernel_addr_r} 14000000 +ubiroot=1 diff --git a/configs/lxr2_defconfig b/configs/lxr2_defconfig new file mode 100644 index 0000000000..855366d421 --- /dev/null +++ b/configs/lxr2_defconfig @@ -0,0 +1,118 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX6=y +CONFIG_TEXT_BASE=0x17800000 +CONFIG_SYS_MALLOC_LEN=0xa00000 +CONFIG_SYS_MALLOC_F_LEN=0x4000 +CONFIG_SPL_GPIO=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_SF_DEFAULT_SPEED=20000000 +CONFIG_ENV_SIZE=0x4000 +CONFIG_ENV_OFFSET=0x100000 +CONFIG_ENV_SECT_SIZE=0x10000 +CONFIG_MX6Q=y +CONFIG_TARGET_LXR2=y +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="imx6q-lxr" +CONFIG_SPL_TEXT_BASE=0x00908000 +CONFIG_SYS_MONITOR_LEN=409600 +CONFIG_SPL_MMC=y +CONFIG_SPL_SERIAL=y +CONFIG_SYS_BOOTCOUNT_ADDR=0x020CC068 +CONFIG_SPL=y +CONFIG_SYS_BOOTCOUNT_SINGLEWORD=y +CONFIG_ENV_OFFSET_REDUND=0x110000 +CONFIG_SPL_LIBDISK_SUPPORT=y +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI=y +CONFIG_LTO=y +CONFIG_HAS_BOARD_SIZE_LIMIT=y +CONFIG_BOARD_SIZE_LIMIT=715766 +CONFIG_FIT=y +CONFIG_SPL_FIT_PRINT=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_SUPPORT_RAW_INITRD=y +CONFIG_SYS_PBSIZE=532 +CONFIG_SYS_CONSOLE_IS_IN_ENV=y +CONFIG_SPL_LEGACY_IMAGE_FORMAT=y +CONFIG_SPL_SYS_MALLOC=y +CONFIG_SPL_FIT_IMAGE_TINY=y +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0x11400 +CONFIG_HUSH_PARSER=y +CONFIG_SYS_MAXARGS=32 +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_SPL=y +CONFIG_CMD_SPL_WRITE_SIZE=0x20000 +CONFIG_CMD_MD5SUM=y +CONFIG_MD5SUM_VERIFY=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_NAND_TRIMFFS=y +CONFIG_CMD_PART=y +CONFIG_CMD_WDT=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_BOOTCOUNT=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand" +CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:40m(Kernels),860m(root),-(nand)" +CONFIG_CMD_UBI=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_EFI_PARTITION=y +# CONFIG_SPL_EFI_PARTITION is not set +CONFIG_OF_CONTROL=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y +CONFIG_ARP_TIMEOUT=200 +CONFIG_BOUNCE_BUFFER=y +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_SYS_BOOTCOUNT_MAGIC=0xB0C4000 +CONFIG_SYS_BOOTCOUNT_BE=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_MXC=y +CONFIG_FSL_USDHC=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_MTD_RAW_NAND=y +CONFIG_NAND_MXS=y +CONFIG_NAND_MXS_DT=y +CONFIG_SYS_NAND_ONFI_DETECTION=y +CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y +CONFIG_SYS_NAND_U_BOOT_OFFS=0xe00000 +CONFIG_DM_SPI_FLASH=y +CONFIG_SF_DEFAULT_BUS=2 +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_PHYLIB=y +CONFIG_PHY_MICREL=y +CONFIG_PHY_MICREL_KSZ90X1=y +CONFIG_FEC_MXC=y +CONFIG_RGMII=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX6=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_DM_SERIAL=y +CONFIG_MXC_UART=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_MXC_SPI=y +CONFIG_SYSRESET=y +CONFIG_SYSRESET_WATCHDOG=y +CONFIG_SYSRESET_WATCHDOG_AUTO=y +CONFIG_IMX_THERMAL=y diff --git a/include/configs/lxr2.h b/include/configs/lxr2.h new file mode 100644 index 0000000000..d8d37a4222 --- /dev/null +++ b/include/configs/lxr2.h @@ -0,0 +1,23 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +// Copyright (C) Stefano Babic + +#ifndef __LXR2_CONFIG_H +#define __LXR2_CONFIG_H + +#include + +#include "mx6_common.h" + +#define PHYS_SDRAM_SIZE SZ_1G + +/* Physical Memory Map */ +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR + +#define CFG_SYS_SDRAM_BASE PHYS_SDRAM +#define CFG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CFG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CFG_SYS_FSL_ESDHC_ADDR 0 +#define CFG_MXC_UART_BASE UART4_BASE + +#endif