The x250 and SE250 are series of 10G L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
cn9130-crb-A.dtb \
cn9130-crb-B.dtb \
ac5-98dx35xx-rd.dtb \
- ac5-98dx35xx-atl-x240.dtb
+ ac5-98dx35xx-atl-x240.dtb \
+ cn9130-atl-x250.dtb
endif
dtb-$(CONFIG_ARCH_SYNQUACER) += synquacer-sc2a11-developerbox.dtb
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Allied Telesis Labs
+ */
+
+#include "cn9130.dtsi"
+
+/ {
+ model = "Allied Telesis x250";
+ compatible = "alliedtelesis,x250",
+ "marvell,cn9130",
+ "marvell,armada-ap806-quad",
+ "marvell,armada-ap806";
+
+ aliases {
+ serial0 = &uart0;
+ i2c0 = &cp0_i2c0;
+ i2c1 = &cp0_i2c1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ fault {
+ label = "fault:red";
+ gpios = <&cp0_gpio1 9 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+ };
+};
+
+/*
+ * AP related configuration
+ */
+&ap_pinctl {
+ /* AP_MPP Pins:
+ * GPIO & NC [0-6,9-10,12]
+ * UART0 [11,19]
+ * UART1 [7,8]
+ * Note: The x250-28XTm PT1 units has the console port wired
+ * to the second uart pins (UART1). This was fixed in all
+ * subsequent models.
+ * Here we choose to configure the pin control for both
+ * uarts to cater for either unit.
+ */
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 0 0 0 0 0 0 0 3 3 0
+ 0 3 0 0 0 0 0 0 0 3 >;
+};
+
+&ap_gpio0 {
+ pp-reset {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_LOW>;
+ output-high;
+ line-name = "pp-reset";
+ };
+};
+
+/*
+ * CP related configuration
+ */
+&cp0_pinctl {
+ /* MPP Bus:
+ * [0-1] DEV
+ * [2-8] GPIO
+ * [9] DEV
+ * [10-12] GPIO
+ * [13] ND_RB
+ * [14] GPIO
+ * [15-28] DEV
+ * [29-30] GPIO
+ * [31] DEV
+ * [32-34] GPIO
+ * [35-36] I2C1
+ * [37-38] I2C0
+ * [39-55] GPIO
+ * [56-60] SPI
+ * [61-62] GPIO
+ */
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 1 1 0 0 0 0 0 0 0 1
+ 0 0 0 2 0 1 1 1 1 1
+ 1 1 1 1 1 1 1 1 1 0
+ 0 1 0 0 0 2 2 2 2 0
+ 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 6 6 6 6
+ 6 0 0>;
+
+ cp0_i2c0_pins: cp0-i2c-pins-0 {
+ marvell,pins = <37 38>;
+ marvell,function = <2>;
+ };
+
+ cp0_i2c0_gpio_pins: cp0-i2c-gpio-pins-0 {
+ marvell,pins = <37 38>;
+ marvell,function = <0>;
+ };
+
+ cp0_i2c1_pins: cp0-i2c-pins-1 {
+ marvell,pins = <35 36>;
+ marvell,function = <2>;
+ };
+
+ cp0_nand_pins: cp0-nand-pins {
+ marvell,pins = <0 1 9 15 16 17 18 19 20 21 22 23 24 25 26 27 28 31>;
+ marvell,function = <1>;
+ };
+
+ cp0_nand_rb: cp0-nand-rb {
+ marvell,pins = <13>;
+ marvell,function = <2>;
+ };
+
+ cp0_spi0_pins: cp0-spi-pins-0 {
+ marvell,pins = <56 57 58 59 60>;
+ marvell,function = <6>;
+ };
+};
+
+&cp0_comphy {
+ phy0 {
+ phy-type = <COMPHY_TYPE_PEX0>;
+ };
+
+ phy1 {
+ phy-type = <COMPHY_TYPE_IGNORE>;
+ };
+
+ phy2 {
+ phy-type = <COMPHY_TYPE_IGNORE>;
+ };
+
+ phy3 {
+ phy-type = <COMPHY_TYPE_IGNORE>;
+ };
+
+ phy4 {
+ phy-type = <COMPHY_TYPE_IGNORE>;
+ };
+
+ phy5 {
+ phy-type = <COMPHY_TYPE_IGNORE>;
+ };
+};
+
+&cp0_pcie0 {
+ num-lanes = <1>;
+ /* non-prefetchable memory */
+ ranges =<0x82000000 0 0xc0000000 0 0xc0000000 0 0x2000000>;
+ status = "disabled";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ clock-frequency = <200000000>;
+};
+
+&cp0_utmi0 {
+ status = "okay";
+};
+
+&cp0_usb3_0 {
+ status = "okay";
+};
+
+&cp0_spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_spi0_pins>;
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+ };
+};
+
+&cp0_nand {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_nand_pins &cp0_nand_rb>;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-timing-mode = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@user {
+ reg = <0x00000000 0x10000000>;
+ label = "user";
+ };
+ };
+};
+
+&cp0_gpio0
+{
+ nand-protect {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "nand-protect";
+ };
+};
+
+&cp0_gpio1
+{
+ usb-en {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-en";
+ };
+
+ phy-reset {
+ gpio-hog;
+ gpios = <21 GPIO_ACTIVE_LOW>;
+ output-high;
+ line-name = "phy-reset";
+ };
+};
+
+&cp0_i2c0 {
+ status = "okay";
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&cp0_i2c0_pins>;
+ pinctrl-1 = <&cp0_i2c0_gpio_pins>;
+ scl-gpios = <&cp0_gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&cp0_gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+ mux@71 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "nxp,pca9546";
+ reg = <0x71>;
+ i2c-mux-idle-disconnect;
+ reset-gpios = <&cp0_gpio1 19 GPIO_ACTIVE_LOW>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ hwmon@2e {
+ compatible = "adi,adt7476";
+ reg = <0x2e>;
+ };
+
+ rtc@68 {
+ compatible = "adi,max31331";
+ reg = <0x68>;
+ };
+ };
+ };
+};
+
+&cp0_i2c1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c1_pins>;
+};
bool "Support Allied Telesis x530"
select 88F6820
+config TARGET_X250
+ bool "Support Allied Telesis x250"
+ select ARMADA_8K
+ imply SCSI
+ imply BOOTSTD_DEFAULTS
+
config TARGET_X240
bool "Support Allied Telesis x240"
select ALLEYCAT_5
default "theadorable" if TARGET_THEADORABLE
default "a38x" if TARGET_CONTROLCENTERDC
default "x530" if TARGET_X530
+ default "x250" if TARGET_X250
default "x240" if TARGET_X240
default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236
default "turris_mox" if TARGET_TURRIS_MOX
default "controlcenterdc" if TARGET_CONTROLCENTERDC
default "x530" if TARGET_X530
+ default "x250" if TARGET_X250
default "x240" if TARGET_X240
default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236
default "CZ.NIC" if TARGET_TURRIS_MOX
default "gdsys" if TARGET_CONTROLCENTERDC
default "alliedtelesis" if TARGET_X530
+ default "alliedtelesis" if TARGET_X250
default "alliedtelesis" if TARGET_X240
default "mikrotik" if TARGET_CRS3XX_98DX3236
default "Marvell" if TARGET_MVEBU_ALLEYCAT5
--- /dev/null
+X250 BOARD
+M: Chris Packham <chris.packham@alliedtelesis.co.nz>
+S: Maintained
+F: board/alliedtelesis/x250/
+F: arch/arm/dts/cn9130-atl-x250.dts
+F: include/configs/x250.h
+F: configs/x250_defconfig
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2024 Allied Telesis
+#
+
+obj-y += x250.o
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <config.h>
+#include <asm/global_data.h>
+#include <linux/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define DEVICE_BUS_SYNC_CTRL 0xF27004C8
+
+int board_init(void)
+{
+ gd->bd->bi_boot_params = CFG_SYS_SDRAM_BASE + 0x100;
+
+ /* DEV_READYn is not needed for NVS, ignore it when accessing CS1 */
+ writel(0x00004001, DEVICE_BUS_SYNC_CTRL);
+
+ return 0;
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_CPU_INIT=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_TEXT_BASE=0x00000000
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000
+CONFIG_TARGET_X250=y
+CONFIG_ENV_SIZE=0x10000
+CONFIG_ENV_OFFSET=0xf80000
+CONFIG_ENV_SECT_SIZE=0x40000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="cn9130-atl-x250"
+CONFIG_SYS_LOAD_ADDR=0x10000000
+CONFIG_DEBUG_UART_BASE=0xf0512000
+CONFIG_DEBUG_UART_CLOCK=200000000
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_BOOTCOMMAND="run distro_bootcmd"
+CONFIG_USE_PREBOOT=y
+CONFIG_SPL_SILENT_CONSOLE=y
+CONFIG_TPL_SILENT_CONSOLE=y
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_UBI=y
+CONFIG_MAC_PARTITION=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
+CONFIG_IPV6=y
+CONFIG_SYS_64BIT_LBA=y
+CONFIG_GPIO_HOG=y
+CONFIG_DM_I2C=y
+CONFIG_DM_I2C_GPIO=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+# CONFIG_INPUT is not set
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_MISC=y
+# CONFIG_MMC is not set
+CONFIG_MTD_RAW_NAND=y
+CONFIG_SYS_NAND_USE_FLASH_BBT=y
+CONFIG_NAND_PXA3XX=y
+CONFIG_SYS_NAND_ONFI_DETECTION=y
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_SST=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_GIGE=y
+CONFIG_E1000=y
+CONFIG_MVPP2=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_MVEBU=y
+CONFIG_PHY=y
+CONFIG_MVEBU_COMPHY_SUPPORT=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_ARMADA_8K=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_DS1307=y
+CONFIG_RTC_MAX313XX=y
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_SYS_NS16550=y
+CONFIG_KIRKWOOD_SPI=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_ETHER_ASIX88179=y
+CONFIG_USB_ETHER_MCS7830=y
+CONFIG_USB_ETHER_RTL8152=y
+CONFIG_USB_ETHER_SMSC95XX=y
+# CONFIG_TOOLS_MKEFICAPSULE is not set
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2024 Allied Telesis
+ */
+
+#ifndef __X250_H_
+#define __X250_H_
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CFG_SYS_TCLK 250000000 /* 250MHz */
+
+/* additions for new ARM relocation support */
+#define CFG_SYS_SDRAM_BASE 0x00000000
+
+#define BOOT_TARGETS "usb scsi pxe dhcp"
+
+#define CFG_EXTRA_ENV_SETTINGS \
+ "scriptaddr=0x6d00000\0" \
+ "pxefile_addr_r=0x6e00000\0" \
+ "fdt_addr_r=0x6f00000\0" \
+ "kernel_addr_r=0x7000000\0" \
+ "ramdisk_addr_r=0xa000000\0" \
+ "fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
+ "boot_targets=" BOOT_TARGETS "\0"
+
+#endif /* __X250_H_ */
projects / u-boot.git / commitdiff