From e3e6782d47f51ec01387ee8e24498a111d0de44f Mon Sep 17 00:00:00 2001 From: Jagan Teki Date: Sat, 13 Jun 2020 13:16:01 +0530 Subject: [PATCH] powerpc: Remove configs/B4420QDS_NAND_defconfig board DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Patch-cc: Ashish Kumar Patch-cc: Ruchika Gupta Signed-off-by: Jagan Teki Reviewed-by: Priyanka Jain --- arch/powerpc/cpu/mpc85xx/Kconfig | 17 - board/freescale/b4860qds/Kconfig | 14 - board/freescale/b4860qds/MAINTAINERS | 17 - board/freescale/b4860qds/Makefile | 16 - board/freescale/b4860qds/b4860qds.c | 1276 ----------------- board/freescale/b4860qds/b4860qds.h | 12 - .../b4860qds/b4860qds_crossbar_con.h | 72 - board/freescale/b4860qds/b4860qds_qixis.h | 28 - board/freescale/b4860qds/b4_pbi.cfg | 30 - board/freescale/b4860qds/b4_rcw.cfg | 7 - board/freescale/b4860qds/ddr.c | 267 ---- board/freescale/b4860qds/eth_b4860qds.c | 454 ------ board/freescale/b4860qds/law.c | 28 - board/freescale/b4860qds/pci.c | 23 - board/freescale/b4860qds/spl.c | 119 -- board/freescale/b4860qds/tlb.c | 154 -- configs/B4420QDS_NAND_defconfig | 69 - configs/B4420QDS_SPIFLASH_defconfig | 55 - configs/B4420QDS_defconfig | 53 - configs/B4860QDS_NAND_defconfig | 69 - configs/B4860QDS_SECURE_BOOT_defconfig | 56 - configs/B4860QDS_SPIFLASH_defconfig | 55 - configs/B4860QDS_SRIO_PCIE_BOOT_defconfig | 49 - configs/B4860QDS_defconfig | 53 - include/configs/B4860QDS.h | 759 ---------- 25 files changed, 3752 deletions(-) delete mode 100644 board/freescale/b4860qds/Kconfig delete mode 100644 board/freescale/b4860qds/MAINTAINERS delete mode 100644 board/freescale/b4860qds/Makefile delete mode 100644 board/freescale/b4860qds/b4860qds.c delete mode 100644 board/freescale/b4860qds/b4860qds.h delete mode 100644 board/freescale/b4860qds/b4860qds_crossbar_con.h delete mode 100644 board/freescale/b4860qds/b4860qds_qixis.h delete mode 100644 board/freescale/b4860qds/b4_pbi.cfg delete mode 100644 board/freescale/b4860qds/b4_rcw.cfg delete mode 100644 board/freescale/b4860qds/ddr.c delete mode 100644 board/freescale/b4860qds/eth_b4860qds.c delete mode 100644 board/freescale/b4860qds/law.c delete mode 100644 board/freescale/b4860qds/pci.c delete mode 100644 board/freescale/b4860qds/spl.c delete mode 100644 board/freescale/b4860qds/tlb.c delete mode 100644 configs/B4420QDS_NAND_defconfig delete mode 100644 configs/B4420QDS_SPIFLASH_defconfig delete mode 100644 configs/B4420QDS_defconfig delete mode 100644 configs/B4860QDS_NAND_defconfig delete mode 100644 configs/B4860QDS_SECURE_BOOT_defconfig delete mode 100644 configs/B4860QDS_SPIFLASH_defconfig delete mode 100644 configs/B4860QDS_SRIO_PCIE_BOOT_defconfig delete mode 100644 configs/B4860QDS_defconfig delete mode 100644 include/configs/B4860QDS.h diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig index 285cc56799..6fb6542ecf 100644 --- a/arch/powerpc/cpu/mpc85xx/Kconfig +++ b/arch/powerpc/cpu/mpc85xx/Kconfig @@ -24,22 +24,6 @@ config TARGET_SOCRATES bool "Support socrates" select ARCH_MPC8544 -config TARGET_B4420QDS - bool "Support B4420QDS" - select ARCH_B4420 - select SUPPORT_SPL - select PHYS_64BIT - imply PANIC_HANG - -config TARGET_B4860QDS - bool "Support B4860QDS" - select ARCH_B4860 - select BOARD_LATE_INIT if CHAIN_OF_TRUST - select SUPPORT_SPL - select PHYS_64BIT - select FSL_DDR_INTERACTIVE if !SPL_BUILD - imply PANIC_HANG - config TARGET_BSC9131RDB bool "Support BSC9131RDB" select ARCH_BSC9131 @@ -1595,7 +1579,6 @@ config SYS_FSL_LBC_CLK_DIV Defines divider of platform clock(clock input to eLBC controller). -source "board/freescale/b4860qds/Kconfig" source "board/freescale/bsc9131rdb/Kconfig" source "board/freescale/bsc9132qds/Kconfig" source "board/freescale/c29xpcie/Kconfig" diff --git a/board/freescale/b4860qds/Kconfig b/board/freescale/b4860qds/Kconfig deleted file mode 100644 index 9bb667ab4f..0000000000 --- a/board/freescale/b4860qds/Kconfig +++ /dev/null @@ -1,14 +0,0 @@ -if TARGET_B4860QDS || TARGET_B4420QDS - -config SYS_BOARD - default "b4860qds" - -config SYS_VENDOR - default "freescale" - -config SYS_CONFIG_NAME - default "B4860QDS" - -source "board/freescale/common/Kconfig" - -endif diff --git a/board/freescale/b4860qds/MAINTAINERS b/board/freescale/b4860qds/MAINTAINERS deleted file mode 100644 index 34ac099e44..0000000000 --- a/board/freescale/b4860qds/MAINTAINERS +++ /dev/null @@ -1,17 +0,0 @@ -B4860QDS BOARD -M: Ashish Kumar -S: Maintained -F: board/freescale/b4860qds/ -F: include/configs/B4860QDS.h -F: configs/B4420QDS_defconfig -F: configs/B4420QDS_NAND_defconfig -F: configs/B4420QDS_SPIFLASH_defconfig -F: configs/B4860QDS_defconfig -F: configs/B4860QDS_NAND_defconfig -F: configs/B4860QDS_SPIFLASH_defconfig -F: configs/B4860QDS_SRIO_PCIE_BOOT_defconfig - -B4860QDS_SECURE_BOOT BOARD -M: Ruchika Gupta -S: Maintained -F: configs/B4860QDS_SECURE_BOOT_defconfig diff --git a/board/freescale/b4860qds/Makefile b/board/freescale/b4860qds/Makefile deleted file mode 100644 index c0ba2c0168..0000000000 --- a/board/freescale/b4860qds/Makefile +++ /dev/null @@ -1,16 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# Copyright 2012 Freescale Semiconductor, Inc. - -ifdef CONFIG_SPL_BUILD -obj-y += spl.o -else -obj-y += b4860qds.o -obj-$(CONFIG_TARGET_B4860QDS) += eth_b4860qds.o -obj-$(CONFIG_TARGET_B4420QDS) += eth_b4860qds.o -obj-$(CONFIG_PCI) += pci.o -endif - -obj-y += ddr.o -obj-y += law.o -obj-y += tlb.o diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c deleted file mode 100644 index cc8ff11ba4..0000000000 --- a/board/freescale/b4860qds/b4860qds.c +++ /dev/null @@ -1,1276 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include "../common/qixis.h" -#include "../common/vsc3316_3308.h" -#include "../common/idt8t49n222a_serdes_clk.h" -#include "../common/zm7300.h" -#include "b4860qds.h" -#include "b4860qds_qixis.h" -#include "b4860qds_crossbar_con.h" - -#define CLK_MUX_SEL_MASK 0x4 -#define ETH_PHY_CLK_OUT 0x4 - -DECLARE_GLOBAL_DATA_PTR; - -int checkboard(void) -{ - char buf[64]; - u8 sw; - struct cpu_type *cpu = gd->arch.cpu; - static const char *const freq[] = {"100", "125", "156.25", "161.13", - "122.88", "122.88", "122.88"}; - int clock; - - printf("Board: %sQDS, ", cpu->name); - printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, ", - QIXIS_READ(id), QIXIS_READ(arch)); - - sw = QIXIS_READ(brdcfg[0]); - sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; - - if (sw < 0x8) - printf("vBank: %d\n", sw); - else if (sw >= 0x8 && sw <= 0xE) - puts("NAND\n"); - else - printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); - - printf("FPGA: v%d (%s), build %d", - (int)QIXIS_READ(scver), qixis_read_tag(buf), - (int)qixis_read_minor()); - /* the timestamp string contains "\n" at the end */ - printf(" on %s", qixis_read_time(buf)); - - /* - * Display the actual SERDES reference clocks as configured by the - * dip switches on the board. Note that the SWx registers could - * technically be set to force the reference clocks to match the - * values that the SERDES expects (or vice versa). For now, however, - * we just display both values and hope the user notices when they - * don't match. - */ - puts("SERDES Reference Clocks: "); - sw = QIXIS_READ(brdcfg[2]); - clock = (sw >> 5) & 7; - printf("Bank1=%sMHz ", freq[clock]); - sw = QIXIS_READ(brdcfg[4]); - clock = (sw >> 6) & 3; - printf("Bank2=%sMHz\n", freq[clock]); - - return 0; -} - -int select_i2c_ch_pca(u8 ch) -{ - int ret; - - /* Selecting proper channel via PCA*/ - ret = i2c_write(I2C_MUX_PCA_ADDR, 0x0, 1, &ch, 1); - if (ret) { - printf("PCA: failed to select proper channel.\n"); - return ret; - } - - return 0; -} - -/* - * read_voltage from sensor on I2C bus - * We use average of 4 readings, waiting for 532us befor another reading - */ -#define WAIT_FOR_ADC 532 /* wait for 532 microseconds for ADC */ -#define NUM_READINGS 4 /* prefer to be power of 2 for efficiency */ - -static inline int read_voltage(void) -{ - int i, ret, voltage_read = 0; - u16 vol_mon; - - for (i = 0; i < NUM_READINGS; i++) { - ret = i2c_read(I2C_VOL_MONITOR_ADDR, - I2C_VOL_MONITOR_BUS_V_OFFSET, 1, (void *)&vol_mon, 2); - if (ret) { - printf("VID: failed to read core voltage\n"); - return ret; - } - if (vol_mon & I2C_VOL_MONITOR_BUS_V_OVF) { - printf("VID: Core voltage sensor error\n"); - return -1; - } - debug("VID: bus voltage reads 0x%04x\n", vol_mon); - /* LSB = 4mv */ - voltage_read += (vol_mon >> I2C_VOL_MONITOR_BUS_V_SHIFT) * 4; - udelay(WAIT_FOR_ADC); - } - /* calculate the average */ - voltage_read /= NUM_READINGS; - - return voltage_read; -} - -static int adjust_vdd(ulong vdd_override) -{ - int re_enable = disable_interrupts(); - ccsr_gur_t __iomem *gur = - (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 fusesr; - u8 vid; - int vdd_target, vdd_last; - int existing_voltage, temp_voltage, voltage; /* all in 1/10 mV */ - int ret; - unsigned int orig_i2c_speed; - unsigned long vdd_string_override; - char *vdd_string; - static const uint16_t vdd[32] = { - 0, /* unused */ - 9875, /* 0.9875V */ - 9750, - 9625, - 9500, - 9375, - 9250, - 9125, - 9000, - 8875, - 8750, - 8625, - 8500, - 8375, - 8250, - 8125, - 10000, /* 1.0000V */ - 10125, - 10250, - 10375, - 10500, - 10625, - 10750, - 10875, - 11000, - 0, /* reserved */ - }; - struct vdd_drive { - u8 vid; - unsigned voltage; - }; - - ret = select_i2c_ch_pca(I2C_MUX_CH_VOL_MONITOR); - if (ret) { - printf("VID: I2c failed to switch channel\n"); - ret = -1; - goto exit; - } - - /* get the voltage ID from fuse status register */ - fusesr = in_be32(&gur->dcfg_fusesr); - vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) & - FSL_CORENET_DCFG_FUSESR_VID_MASK; - if (vid == FSL_CORENET_DCFG_FUSESR_VID_MASK) { - vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) & - FSL_CORENET_DCFG_FUSESR_ALTVID_MASK; - } - vdd_target = vdd[vid]; - debug("VID:Reading from from fuse,vid=%x vdd is %dmV\n", - vid, vdd_target/10); - - /* check override variable for overriding VDD */ - vdd_string = env_get("b4qds_vdd_mv"); - if (vdd_override == 0 && vdd_string && - !strict_strtoul(vdd_string, 10, &vdd_string_override)) - vdd_override = vdd_string_override; - if (vdd_override >= 819 && vdd_override <= 1212) { - vdd_target = vdd_override * 10; /* convert to 1/10 mV */ - debug("VDD override is %lu\n", vdd_override); - } else if (vdd_override != 0) { - printf("Invalid value.\n"); - } - - if (vdd_target == 0) { - printf("VID: VID not used\n"); - ret = 0; - goto exit; - } - - /* - * Read voltage monitor to check real voltage. - * Voltage monitor LSB is 4mv. - */ - vdd_last = read_voltage(); - if (vdd_last < 0) { - printf("VID: abort VID adjustment\n"); - ret = -1; - goto exit; - } - - debug("VID: Core voltage is at %d mV\n", vdd_last); - ret = select_i2c_ch_pca(I2C_MUX_CH_DPM); - if (ret) { - printf("VID: I2c failed to switch channel to DPM\n"); - ret = -1; - goto exit; - } - - /* Round up to the value of step of Voltage regulator */ - voltage = roundup(vdd_target, ZM_STEP); - debug("VID: rounded up voltage = %d\n", voltage); - - /* lower the speed to 100kHz to access ZM7300 device */ - debug("VID: Setting bus speed to 100KHz if not already set\n"); - orig_i2c_speed = i2c_get_bus_speed(); - if (orig_i2c_speed != 100000) - i2c_set_bus_speed(100000); - - /* Read the existing level on board, if equal to requsted one, - no need to re-set */ - existing_voltage = zm_read_voltage(); - - /* allowing the voltage difference of one step 0.0125V acceptable */ - if ((existing_voltage >= voltage) && - (existing_voltage < (voltage + ZM_STEP))) { - debug("VID: voltage already set as requested,returning\n"); - ret = existing_voltage; - goto out; - } - debug("VID: Changing voltage for board from %dmV to %dmV\n", - existing_voltage/10, voltage/10); - - if (zm_disable_wp() < 0) { - ret = -1; - goto out; - } - /* Change Voltage: the change is done through all the steps in the - way, to avoid reset to the board due to power good signal fail - in big voltage change gap jump. - */ - if (existing_voltage > voltage) { - temp_voltage = existing_voltage - ZM_STEP; - while (temp_voltage >= voltage) { - ret = zm_write_voltage(temp_voltage); - if (ret == temp_voltage) { - temp_voltage -= ZM_STEP; - } else { - /* ZM7300 device failed to set - * the voltage */ - printf - ("VID:Stepping down vol failed:%dmV\n", - temp_voltage/10); - ret = -1; - goto out; - } - } - } else { - temp_voltage = existing_voltage + ZM_STEP; - while (temp_voltage < (voltage + ZM_STEP)) { - ret = zm_write_voltage(temp_voltage); - if (ret == temp_voltage) { - temp_voltage += ZM_STEP; - } else { - /* ZM7300 device failed to set - * the voltage */ - printf - ("VID:Stepping up vol failed:%dmV\n", - temp_voltage/10); - ret = -1; - goto out; - } - } - } - - if (zm_enable_wp() < 0) - ret = -1; - - /* restore the speed to 400kHz */ -out: debug("VID: Restore the I2C bus speed to %dKHz\n", - orig_i2c_speed/1000); - i2c_set_bus_speed(orig_i2c_speed); - if (ret < 0) - goto exit; - - ret = select_i2c_ch_pca(I2C_MUX_CH_VOL_MONITOR); - if (ret) { - printf("VID: I2c failed to switch channel\n"); - ret = -1; - goto exit; - } - vdd_last = read_voltage(); - select_i2c_ch_pca(I2C_CH_DEFAULT); - - if (vdd_last > 0) - printf("VID: Core voltage %d mV\n", vdd_last); - else - ret = -1; - -exit: - if (re_enable) - enable_interrupts(); - return ret; -} - -int configure_vsc3316_3308(void) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - unsigned int num_vsc16_con, num_vsc08_con; - u32 serdes1_prtcl, serdes2_prtcl; - int ret; - char buffer[HWCONFIG_BUFFER_SIZE]; - char *buf = NULL; - - serdes1_prtcl = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS1_PRTCL; - if (!serdes1_prtcl) { - printf("SERDES1 is not enabled\n"); - return 0; - } - serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; - debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl); - - serdes2_prtcl = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS2_PRTCL; - if (!serdes2_prtcl) { - printf("SERDES2 is not enabled\n"); - return 0; - } - serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; - debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl); - - switch (serdes1_prtcl) { - case 0x29: - case 0x2a: - case 0x2C: - case 0x2D: - case 0x2E: - /* - * Configuration: - * SERDES: 1 - * Lanes: A,B: SGMII - * Lanes: C,D,E,F,G,H: CPRI - */ - debug("Configuring crossbar to use onboard SGMII PHYs:" - "srds_prctl:%x\n", serdes1_prtcl); - num_vsc16_con = NUM_CON_VSC3316; - /* Configure VSC3316 crossbar switch */ - ret = select_i2c_ch_pca(I2C_CH_VSC3316); - if (!ret) { - ret = vsc3316_config(VSC3316_TX_ADDRESS, - vsc16_tx_4sfp_sgmii_12_56, - num_vsc16_con); - if (ret) - return ret; - ret = vsc3316_config(VSC3316_RX_ADDRESS, - vsc16_rx_4sfp_sgmii_12_56, - num_vsc16_con); - if (ret) - return ret; - } else { - return ret; - } - break; - - case 0x01: - case 0x02: - case 0x04: - case 0x05: - case 0x06: - case 0x07: - case 0x08: - case 0x09: - case 0x0A: - case 0x0B: - case 0x0C: - case 0x2F: - case 0x30: - case 0x32: - case 0x33: - case 0x34: - case 0x39: - case 0x3A: - case 0x3C: - case 0x3D: - case 0x5C: - case 0x5D: - /* - * Configuration: - * SERDES: 1 - * Lanes: A,B: AURORA - * Lanes: C,d: SGMII - * Lanes: E,F,G,H: CPRI - */ - debug("Configuring crossbar for Aurora, SGMII 3 and 4," - " and CPRI. srds_prctl:%x\n", serdes1_prtcl); - num_vsc16_con = NUM_CON_VSC3316; - /* Configure VSC3316 crossbar switch */ - ret = select_i2c_ch_pca(I2C_CH_VSC3316); - if (!ret) { - ret = vsc3316_config(VSC3316_TX_ADDRESS, - vsc16_tx_sfp_sgmii_aurora, - num_vsc16_con); - if (ret) - return ret; - ret = vsc3316_config(VSC3316_RX_ADDRESS, - vsc16_rx_sfp_sgmii_aurora, - num_vsc16_con); - if (ret) - return ret; - } else { - return ret; - } - break; - -#ifdef CONFIG_ARCH_B4420 - case 0x17: - case 0x18: - /* - * Configuration: - * SERDES: 1 - * Lanes: A,B,C,D: SGMII - * Lanes: E,F,G,H: CPRI - */ - debug("Configuring crossbar to use onboard SGMII PHYs:" - "srds_prctl:%x\n", serdes1_prtcl); - num_vsc16_con = NUM_CON_VSC3316; - /* Configure VSC3316 crossbar switch */ - ret = select_i2c_ch_pca(I2C_CH_VSC3316); - if (!ret) { - ret = vsc3316_config(VSC3316_TX_ADDRESS, - vsc16_tx_sgmii_lane_cd, num_vsc16_con); - if (ret) - return ret; - ret = vsc3316_config(VSC3316_RX_ADDRESS, - vsc16_rx_sgmii_lane_cd, num_vsc16_con); - if (ret) - return ret; - } else { - return ret; - } - break; -#endif - - case 0x3E: - case 0x0D: - case 0x0E: - case 0x12: - num_vsc16_con = NUM_CON_VSC3316; - /* Configure VSC3316 crossbar switch */ - ret = select_i2c_ch_pca(I2C_CH_VSC3316); - if (!ret) { - ret = vsc3316_config(VSC3316_TX_ADDRESS, - vsc16_tx_sfp, num_vsc16_con); - if (ret) - return ret; - ret = vsc3316_config(VSC3316_RX_ADDRESS, - vsc16_rx_sfp, num_vsc16_con); - if (ret) - return ret; - } else { - return ret; - } - break; - default: - printf("WARNING:VSC crossbars programming not supported for:%x" - " SerDes1 Protocol.\n", serdes1_prtcl); - return -1; - } - - num_vsc08_con = NUM_CON_VSC3308; - /* Configure VSC3308 crossbar switch */ - ret = select_i2c_ch_pca(I2C_CH_VSC3308); - switch (serdes2_prtcl) { -#ifdef CONFIG_ARCH_B4420 - case 0x9d: -#endif - case 0x9E: - case 0x9A: - case 0x98: - case 0x48: - case 0x49: - case 0x4E: - case 0x79: - case 0x7A: - if (!ret) { - ret = vsc3308_config(VSC3308_TX_ADDRESS, - vsc08_tx_amc, num_vsc08_con); - if (ret) - return ret; - ret = vsc3308_config(VSC3308_RX_ADDRESS, - vsc08_rx_amc, num_vsc08_con); - if (ret) - return ret; - } else { - return ret; - } - break; - case 0x80: - case 0x81: - case 0x82: - case 0x83: - case 0x84: - case 0x85: - case 0x86: - case 0x87: - case 0x88: - case 0x89: - case 0x8a: - case 0x8b: - case 0x8c: - case 0x8d: - case 0x8e: - case 0xb1: - case 0xb2: - if (!ret) { - /* - * Extract hwconfig from environment since environment - * is not setup properly yet - */ - env_get_f("hwconfig", buffer, sizeof(buffer)); - buf = buffer; - - if (hwconfig_subarg_cmp_f("fsl_b4860_serdes2", - "sfp_amc", "sfp", buf)) { -#ifdef CONFIG_SYS_FSL_B4860QDS_XFI_ERR - /* change default VSC3308 for XFI erratum */ - ret = vsc3308_config_adjust(VSC3308_TX_ADDRESS, - vsc08_tx_sfp, num_vsc08_con); - if (ret) - return ret; - - ret = vsc3308_config_adjust(VSC3308_RX_ADDRESS, - vsc08_rx_sfp, num_vsc08_con); - if (ret) - return ret; -#else - ret = vsc3308_config(VSC3308_TX_ADDRESS, - vsc08_tx_sfp, num_vsc08_con); - if (ret) - return ret; - - ret = vsc3308_config(VSC3308_RX_ADDRESS, - vsc08_rx_sfp, num_vsc08_con); - if (ret) - return ret; -#endif - } else { - ret = vsc3308_config(VSC3308_TX_ADDRESS, - vsc08_tx_amc, num_vsc08_con); - if (ret) - return ret; - - ret = vsc3308_config(VSC3308_RX_ADDRESS, - vsc08_rx_amc, num_vsc08_con); - if (ret) - return ret; - } - - } else { - return ret; - } - break; - default: - printf("WARNING:VSC crossbars programming not supported for: %x" - " SerDes2 Protocol.\n", serdes2_prtcl); - return -1; - } - - return 0; -} - -static int calibrate_pll(serdes_corenet_t *srds_regs, int pll_num) -{ - u32 rst_err; - - /* Steps For SerDes PLLs reset and reconfiguration - * or PLL power-up procedure - */ - debug("CALIBRATE PLL:%d\n", pll_num); - clrbits_be32(&srds_regs->bank[pll_num].rstctl, - SRDS_RSTCTL_SDRST_B); - udelay(10); - clrbits_be32(&srds_regs->bank[pll_num].rstctl, - (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B)); - udelay(10); - setbits_be32(&srds_regs->bank[pll_num].rstctl, - SRDS_RSTCTL_RST); - setbits_be32(&srds_regs->bank[pll_num].rstctl, - (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B - | SRDS_RSTCTL_SDRST_B)); - - udelay(20); - - /* Check whether PLL has been locked or not */ - rst_err = in_be32(&srds_regs->bank[pll_num].rstctl) & - SRDS_RSTCTL_RSTERR; - rst_err >>= SRDS_RSTCTL_RSTERR_SHIFT; - debug("RST_ERR value for PLL %d is: 0x%x:\n", pll_num, rst_err); - if (rst_err) - return rst_err; - - return rst_err; -} - -static int check_pll_locks(serdes_corenet_t *srds_regs, int pll_num) -{ - int ret = 0; - u32 fcap, dcbias, bcap, pllcr1, pllcr0; - - if (calibrate_pll(srds_regs, pll_num)) { - /* STEP 1 */ - /* Read fcap, dcbias and bcap value */ - clrbits_be32(&srds_regs->bank[pll_num].pllcr0, - SRDS_PLLCR0_DCBIAS_OUT_EN); - fcap = in_be32(&srds_regs->bank[pll_num].pllsr2) & - SRDS_PLLSR2_FCAP; - fcap >>= SRDS_PLLSR2_FCAP_SHIFT; - bcap = in_be32(&srds_regs->bank[pll_num].pllsr2) & - SRDS_PLLSR2_BCAP_EN; - bcap >>= SRDS_PLLSR2_BCAP_EN_SHIFT; - setbits_be32(&srds_regs->bank[pll_num].pllcr0, - SRDS_PLLCR0_DCBIAS_OUT_EN); - dcbias = in_be32(&srds_regs->bank[pll_num].pllsr2) & - SRDS_PLLSR2_DCBIAS; - dcbias >>= SRDS_PLLSR2_DCBIAS_SHIFT; - debug("values of bcap:%x, fcap:%x and dcbias:%x\n", - bcap, fcap, dcbias); - if (fcap == 0 && bcap == 1) { - /* Step 3 */ - clrbits_be32(&srds_regs->bank[pll_num].rstctl, - (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B - | SRDS_RSTCTL_SDRST_B)); - clrbits_be32(&srds_regs->bank[pll_num].pllcr1, - SRDS_PLLCR1_BCAP_EN); - setbits_be32(&srds_regs->bank[pll_num].pllcr1, - SRDS_PLLCR1_BCAP_OVD); - if (calibrate_pll(srds_regs, pll_num)) { - /*save the fcap, dcbias and bcap values*/ - clrbits_be32(&srds_regs->bank[pll_num].pllcr0, - SRDS_PLLCR0_DCBIAS_OUT_EN); - fcap = in_be32(&srds_regs->bank[pll_num].pllsr2) - & SRDS_PLLSR2_FCAP; - fcap >>= SRDS_PLLSR2_FCAP_SHIFT; - bcap = in_be32(&srds_regs->bank[pll_num].pllsr2) - & SRDS_PLLSR2_BCAP_EN; - bcap >>= SRDS_PLLSR2_BCAP_EN_SHIFT; - setbits_be32(&srds_regs->bank[pll_num].pllcr0, - SRDS_PLLCR0_DCBIAS_OUT_EN); - dcbias = in_be32 - (&srds_regs->bank[pll_num].pllsr2) & - SRDS_PLLSR2_DCBIAS; - dcbias >>= SRDS_PLLSR2_DCBIAS_SHIFT; - - /* Step 4*/ - clrbits_be32(&srds_regs->bank[pll_num].rstctl, - (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B - | SRDS_RSTCTL_SDRST_B)); - setbits_be32(&srds_regs->bank[pll_num].pllcr1, - SRDS_PLLCR1_BYP_CAL); - clrbits_be32(&srds_regs->bank[pll_num].pllcr1, - SRDS_PLLCR1_BCAP_EN); - setbits_be32(&srds_regs->bank[pll_num].pllcr1, - SRDS_PLLCR1_BCAP_OVD); - /* change the fcap and dcbias to the saved - * values from Step 3 */ - clrbits_be32(&srds_regs->bank[pll_num].pllcr1, - SRDS_PLLCR1_PLL_FCAP); - pllcr1 = (in_be32 - (&srds_regs->bank[pll_num].pllcr1)| - (fcap << SRDS_PLLCR1_PLL_FCAP_SHIFT)); - out_be32(&srds_regs->bank[pll_num].pllcr1, - pllcr1); - clrbits_be32(&srds_regs->bank[pll_num].pllcr0, - SRDS_PLLCR0_DCBIAS_OVRD); - pllcr0 = (in_be32 - (&srds_regs->bank[pll_num].pllcr0)| - (dcbias << SRDS_PLLCR0_DCBIAS_OVRD_SHIFT)); - out_be32(&srds_regs->bank[pll_num].pllcr0, - pllcr0); - ret = calibrate_pll(srds_regs, pll_num); - if (ret) - return ret; - } else { - goto out; - } - } else { /* Step 5 */ - clrbits_be32(&srds_regs->bank[pll_num].rstctl, - (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B - | SRDS_RSTCTL_SDRST_B)); - udelay(10); - /* Change the fcap, dcbias, and bcap to the - * values from Step 1 */ - setbits_be32(&srds_regs->bank[pll_num].pllcr1, - SRDS_PLLCR1_BYP_CAL); - clrbits_be32(&srds_regs->bank[pll_num].pllcr1, - SRDS_PLLCR1_PLL_FCAP); - pllcr1 = (in_be32(&srds_regs->bank[pll_num].pllcr1)| - (fcap << SRDS_PLLCR1_PLL_FCAP_SHIFT)); - out_be32(&srds_regs->bank[pll_num].pllcr1, - pllcr1); - clrbits_be32(&srds_regs->bank[pll_num].pllcr0, - SRDS_PLLCR0_DCBIAS_OVRD); - pllcr0 = (in_be32(&srds_regs->bank[pll_num].pllcr0)| - (dcbias << SRDS_PLLCR0_DCBIAS_OVRD_SHIFT)); - out_be32(&srds_regs->bank[pll_num].pllcr0, - pllcr0); - clrbits_be32(&srds_regs->bank[pll_num].pllcr1, - SRDS_PLLCR1_BCAP_EN); - setbits_be32(&srds_regs->bank[pll_num].pllcr1, - SRDS_PLLCR1_BCAP_OVD); - ret = calibrate_pll(srds_regs, pll_num); - if (ret) - return ret; - } - } -out: - return 0; -} - -static int check_serdes_pll_locks(void) -{ - serdes_corenet_t *srds1_regs = - (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; - serdes_corenet_t *srds2_regs = - (void *)CONFIG_SYS_FSL_CORENET_SERDES2_ADDR; - int i, ret1, ret2; - - debug("\nSerDes1 Lock check\n"); - for (i = 0; i < CONFIG_SYS_FSL_SRDS_NUM_PLLS; i++) { - ret1 = check_pll_locks(srds1_regs, i); - if (ret1) { - printf("SerDes1, PLL:%d didnt lock\n", i); - return ret1; - } - } - debug("\nSerDes2 Lock check\n"); - for (i = 0; i < CONFIG_SYS_FSL_SRDS_NUM_PLLS; i++) { - ret2 = check_pll_locks(srds2_regs, i); - if (ret2) { - printf("SerDes2, PLL:%d didnt lock\n", i); - return ret2; - } - } - - return 0; -} - -int config_serdes1_refclks(void) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - serdes_corenet_t *srds_regs = - (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; - u32 serdes1_prtcl, lane; - unsigned int flag_sgmii_aurora_prtcl = 0; - int i; - int ret = 0; - - serdes1_prtcl = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS1_PRTCL; - if (!serdes1_prtcl) { - printf("SERDES1 is not enabled\n"); - return -1; - } - serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; - debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl); - - /* To prevent generation of reset request from SerDes - * while changing the refclks, By setting SRDS_RST_MSK bit, - * SerDes reset event cannot cause a reset request - */ - setbits_be32(&gur->rstrqmr1, FSL_CORENET_RSTRQMR1_SRDS_RST_MSK); - - /* Reconfigure IDT idt8t49n222a device for CPRI to work - * For this SerDes1's Refclk1 and refclk2 need to be set - * to 122.88MHz - */ - switch (serdes1_prtcl) { - case 0x29: - case 0x2A: - case 0x2C: - case 0x2D: - case 0x2E: - case 0x01: - case 0x02: - case 0x04: - case 0x05: - case 0x06: - case 0x07: - case 0x08: - case 0x09: - case 0x0A: - case 0x0B: - case 0x0C: - case 0x2F: - case 0x30: - case 0x32: - case 0x33: - case 0x34: - case 0x39: - case 0x3A: - case 0x3C: - case 0x3D: - case 0x5C: - case 0x5D: - debug("Configuring idt8t49n222a for CPRI SerDes clks:" - " for srds_prctl:%x\n", serdes1_prtcl); - ret = select_i2c_ch_pca(I2C_CH_IDT); - if (!ret) { - ret = set_serdes_refclk(IDT_SERDES1_ADDRESS, 1, - SERDES_REFCLK_122_88, - SERDES_REFCLK_122_88, 0); - if (ret) { - printf("IDT8T49N222A configuration failed.\n"); - goto out; - } else - debug("IDT8T49N222A configured.\n"); - } else { - goto out; - } - select_i2c_ch_pca(I2C_CH_DEFAULT); - - /* Change SerDes1's Refclk1 to 125MHz for on board - * SGMIIs or Aurora to work - */ - for (lane = 0; lane < SRDS_MAX_LANES; lane++) { - enum srds_prtcl lane_prtcl = serdes_get_prtcl - (0, serdes1_prtcl, lane); - switch (lane_prtcl) { - case SGMII_FM1_DTSEC1: - case SGMII_FM1_DTSEC2: - case SGMII_FM1_DTSEC3: - case SGMII_FM1_DTSEC4: - case SGMII_FM1_DTSEC5: - case SGMII_FM1_DTSEC6: - case AURORA: - flag_sgmii_aurora_prtcl++; - break; - default: - break; - } - } - - if (flag_sgmii_aurora_prtcl) - QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125); - - /* Steps For SerDes PLLs reset and reconfiguration after - * changing SerDes's refclks - */ - for (i = 0; i < CONFIG_SYS_FSL_SRDS_NUM_PLLS; i++) { - debug("For PLL%d reset and reconfiguration after" - " changing refclks\n", i+1); - clrbits_be32(&srds_regs->bank[i].rstctl, - SRDS_RSTCTL_SDRST_B); - udelay(10); - clrbits_be32(&srds_regs->bank[i].rstctl, - (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B)); - udelay(10); - setbits_be32(&srds_regs->bank[i].rstctl, - SRDS_RSTCTL_RST); - setbits_be32(&srds_regs->bank[i].rstctl, - (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B - | SRDS_RSTCTL_SDRST_B)); - } - break; - default: - printf("WARNING:IDT8T49N222A configuration not" - " supported for:%x SerDes1 Protocol.\n", - serdes1_prtcl); - } - -out: - /* Clearing SRDS_RST_MSK bit as now - * SerDes reset event can cause a reset request - */ - clrbits_be32(&gur->rstrqmr1, FSL_CORENET_RSTRQMR1_SRDS_RST_MSK); - return ret; -} - -int config_serdes2_refclks(void) -{ - ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - serdes_corenet_t *srds2_regs = - (void *)CONFIG_SYS_FSL_CORENET_SERDES2_ADDR; - u32 serdes2_prtcl; - int ret = 0; - int i; - - serdes2_prtcl = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS2_PRTCL; - if (!serdes2_prtcl) { - debug("SERDES2 is not enabled\n"); - return -ENODEV; - } - serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; - debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl); - - /* To prevent generation of reset request from SerDes - * while changing the refclks, By setting SRDS_RST_MSK bit, - * SerDes reset event cannot cause a reset request - */ - setbits_be32(&gur->rstrqmr1, FSL_CORENET_RSTRQMR1_SRDS_RST_MSK); - - /* Reconfigure IDT idt8t49n222a device for PCIe SATA to work - * For this SerDes2's Refclk1 need to be set to 100MHz - */ - switch (serdes2_prtcl) { -#ifdef CONFIG_ARCH_B4420 - case 0x9d: -#endif - case 0x9E: - case 0x9A: - /* fallthrough */ - case 0xb1: - case 0xb2: - debug("Configuring IDT for PCIe SATA for srds_prctl:%x\n", - serdes2_prtcl); - ret = select_i2c_ch_pca(I2C_CH_IDT); - if (!ret) { - ret = set_serdes_refclk(IDT_SERDES2_ADDRESS, 2, - SERDES_REFCLK_100, - SERDES_REFCLK_156_25, 0); - if (ret) { - printf("IDT8T49N222A configuration failed.\n"); - goto out; - } else - debug("IDT8T49N222A configured.\n"); - } else { - goto out; - } - select_i2c_ch_pca(I2C_CH_DEFAULT); - - /* Steps For SerDes PLLs reset and reconfiguration after - * changing SerDes's refclks - */ - for (i = 0; i < CONFIG_SYS_FSL_SRDS_NUM_PLLS; i++) { - clrbits_be32(&srds2_regs->bank[i].rstctl, - SRDS_RSTCTL_SDRST_B); - udelay(10); - clrbits_be32(&srds2_regs->bank[i].rstctl, - (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B)); - udelay(10); - setbits_be32(&srds2_regs->bank[i].rstctl, - SRDS_RSTCTL_RST); - setbits_be32(&srds2_regs->bank[i].rstctl, - (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B - | SRDS_RSTCTL_SDRST_B)); - - udelay(10); - } - break; - default: - printf("IDT configuration not supported for:%x S2 Protocol.\n", - serdes2_prtcl); - } - -out: - /* Clearing SRDS_RST_MSK bit as now - * SerDes reset event can cause a reset request - */ - clrbits_be32(&gur->rstrqmr1, FSL_CORENET_RSTRQMR1_SRDS_RST_MSK); - return ret; -} - -int board_early_init_r(void) -{ - const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; - int flash_esel = find_tlb_idx((void *)flashbase, 1); - int ret; - u32 svr = SVR_SOC_VER(get_svr()); - - /* Create law for MAPLE only for personalities having MAPLE */ - if ((svr == SVR_B4860) || (svr == SVR_B4440) || - (svr == SVR_B4420) || (svr == SVR_B4220)) { - set_next_law(CONFIG_SYS_MAPLE_MEM_PHYS, LAW_SIZE_16M, - LAW_TRGT_IF_MAPLE); - } - - /* - * Remap Boot flash + PROMJET region to caching-inhibited - * so that flash can be erased properly. - */ - - /* Flush d-cache and invalidate i-cache of any FLASH data */ - flush_dcache(); - invalidate_icache(); - - if (flash_esel == -1) { - /* very unlikely unless something is messed up */ - puts("Error: Could not find TLB for FLASH BASE\n"); - flash_esel = 2; /* give our best effort to continue */ - } else { - /* invalidate existing TLB entry for flash + promjet */ - disable_tlb(flash_esel); - } - - set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, flash_esel, BOOKE_PAGESZ_256M, 1); - - /* - * Adjust core voltage according to voltage ID - * This function changes I2C mux to channel 2. - */ - if (adjust_vdd(0) < 0) - printf("Warning: Adjusting core voltage failed\n"); - - /* SerDes1 refclks need to be set again, as default clks - * are not suitable for CPRI and onboard SGMIIs to work - * simultaneously. - * This function will set SerDes1's Refclk1 and refclk2 - * as per SerDes1 protocols - */ - if (config_serdes1_refclks()) - printf("SerDes1 Refclks couldn't set properly.\n"); - else - printf("SerDes1 Refclks have been set.\n"); - - /* SerDes2 refclks need to be set again, as default clks - * are not suitable for PCIe SATA to work - * This function will set SerDes2's Refclk1 and refclk2 - * for SerDes2 protocols having PCIe in them - * for PCIe SATA to work - */ - ret = config_serdes2_refclks(); - if (!ret) - printf("SerDes2 Refclks have been set.\n"); - else if (ret == -ENODEV) - printf("SerDes disable, Refclks couldn't change.\n"); - else - printf("SerDes2 Refclk reconfiguring failed.\n"); - -#if defined(CONFIG_SYS_FSL_ERRATUM_A006384) || \ - defined(CONFIG_SYS_FSL_ERRATUM_A006475) - /* Rechecking the SerDes locks after all SerDes configurations - * are done, As SerDes PLLs may not lock reliably at 5 G VCO - * and at cold temperatures. - * Following sequence ensure the proper locking of SerDes PLLs. - */ - if (SVR_MAJ(get_svr()) == 1) { - if (check_serdes_pll_locks()) - printf("SerDes plls still not locked properly.\n"); - else - printf("SerDes plls have been locked well.\n"); - } -#endif - - /* Configure VSC3316 and VSC3308 crossbar switches */ - if (configure_vsc3316_3308()) - printf("VSC:failed to configure VSC3316/3308.\n"); - else - printf("VSC:VSC3316/3308 successfully configured.\n"); - - select_i2c_ch_pca(I2C_CH_DEFAULT); - - return 0; -} - -unsigned long get_board_sys_clk(void) -{ - u8 sysclk_conf = QIXIS_READ(brdcfg[1]); - - switch ((sysclk_conf & 0x0C) >> 2) { - case QIXIS_CLK_100: - return 100000000; - case QIXIS_CLK_125: - return 125000000; - case QIXIS_CLK_133: - return 133333333; - } - return 66666666; -} - -unsigned long get_board_ddr_clk(void) -{ - u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); - - switch (ddrclk_conf & 0x03) { - case QIXIS_CLK_100: - return 100000000; - case QIXIS_CLK_125: - return 125000000; - case QIXIS_CLK_133: - return 133333333; - } - return 66666666; -} - -static int serdes_refclock(u8 sw, u8 sdclk) -{ - unsigned int clock; - int ret = -1; - u8 brdcfg4; - - if (sdclk == 1) { - brdcfg4 = QIXIS_READ(brdcfg[4]); - if ((brdcfg4 & CLK_MUX_SEL_MASK) == ETH_PHY_CLK_OUT) - return SRDS_PLLCR0_RFCK_SEL_125; - else - clock = (sw >> 5) & 7; - } else - clock = (sw >> 6) & 3; - - switch (clock) { - case 0: - ret = SRDS_PLLCR0_RFCK_SEL_100; - break; - case 1: - ret = SRDS_PLLCR0_RFCK_SEL_125; - break; - case 2: - ret = SRDS_PLLCR0_RFCK_SEL_156_25; - break; - case 3: - ret = SRDS_PLLCR0_RFCK_SEL_161_13; - break; - case 4: - case 5: - case 6: - ret = SRDS_PLLCR0_RFCK_SEL_122_88; - break; - default: - ret = -1; - break; - } - - return ret; -} - -#define NUM_SRDS_BANKS 2 - -int misc_init_r(void) -{ - u8 sw; - serdes_corenet_t *srds_regs = - (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; - u32 actual[NUM_SRDS_BANKS]; - unsigned int i; - int clock; - - sw = QIXIS_READ(brdcfg[2]); - clock = serdes_refclock(sw, 1); - if (clock >= 0) - actual[0] = clock; - else - printf("Warning: SDREFCLK1 switch setting is unsupported\n"); - - sw = QIXIS_READ(brdcfg[4]); - clock = serdes_refclock(sw, 2); - if (clock >= 0) - actual[1] = clock; - else - printf("Warning: SDREFCLK2 switch setting unsupported\n"); - - for (i = 0; i < NUM_SRDS_BANKS; i++) { - u32 pllcr0 = srds_regs->bank[i].pllcr0; - u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK; - if (expected != actual[i]) { - printf("Warning: SERDES bank %u expects reference clock" - " %sMHz, but actual is %sMHz\n", i + 1, - serdes_clock_to_string(expected), - serdes_clock_to_string(actual[i])); - } - } - - return 0; -} - -int ft_board_setup(void *blob, bd_t *bd) -{ - phys_addr_t base; - phys_size_t size; - - ft_cpu_setup(blob, bd); - - base = env_get_bootm_low(); - size = env_get_bootm_size(); - - fdt_fixup_memory(blob, (u64)base, (u64)size); - -#ifdef CONFIG_PCI - pci_of_setup(blob, bd); -#endif - - fdt_fixup_liodn(blob); - -#ifdef CONFIG_HAS_FSL_DR_USB - fsl_fdt_fixup_dr_usb(blob, bd); -#endif - -#ifdef CONFIG_SYS_DPAA_FMAN -#ifndef CONFIG_DM_ETH - fdt_fixup_fman_ethernet(blob); -#endif - fdt_fixup_board_enet(blob); -#endif - - return 0; -} - -/* - * Dump board switch settings. - * The bits that cannot be read/sampled via some FPGA or some - * registers, they will be displayed as - * underscore in binary format. mask[] has those bits. - * Some bits are calculated differently than the actual switches - * if booting with overriding by FPGA. - */ -void qixis_dump_switch(void) -{ - int i; - u8 sw[5]; - - /* - * Any bit with 1 means that bit cannot be reverse engineered. - * It will be displayed as _ in binary format. - */ - static const u8 mask[] = {0x07, 0, 0, 0xff, 0}; - char buf[10]; - u8 brdcfg[16], dutcfg[16]; - - for (i = 0; i < 16; i++) { - brdcfg[i] = qixis_read(offsetof(struct qixis, brdcfg[0]) + i); - dutcfg[i] = qixis_read(offsetof(struct qixis, dutcfg[0]) + i); - } - - sw[0] = ((brdcfg[0] & 0x0f) << 4) | \ - (brdcfg[9] & 0x08); - sw[1] = ((dutcfg[1] & 0x01) << 7) | \ - ((dutcfg[2] & 0x07) << 4) | \ - ((dutcfg[6] & 0x10) >> 1) | \ - ((dutcfg[6] & 0x80) >> 5) | \ - ((dutcfg[1] & 0x40) >> 5) | \ - (dutcfg[6] & 0x01); - sw[2] = dutcfg[0]; - sw[3] = 0; - sw[4] = ((brdcfg[1] & 0x30) << 2) | \ - ((brdcfg[1] & 0xc0) >> 2) | \ - (brdcfg[1] & 0x0f); - - puts("DIP switch settings:\n"); - for (i = 0; i < 5; i++) { - printf("SW%d = 0b%s (0x%02x)\n", - i + 1, byte_to_binary_mask(sw[i], mask[i], buf), sw[i]); - } -} diff --git a/board/freescale/b4860qds/b4860qds.h b/board/freescale/b4860qds/b4860qds.h deleted file mode 100644 index 4a8e91b58f..0000000000 --- a/board/freescale/b4860qds/b4860qds.h +++ /dev/null @@ -1,12 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - */ - -#ifndef __CORENET_DS_H__ -#define __CORENET_DS_H__ - -void fdt_fixup_board_enet(void *blob); -void pci_of_setup(void *blob, bd_t *bd); - -#endif diff --git a/board/freescale/b4860qds/b4860qds_crossbar_con.h b/board/freescale/b4860qds/b4860qds_crossbar_con.h deleted file mode 100644 index b9d59c23be..0000000000 --- a/board/freescale/b4860qds/b4860qds_crossbar_con.h +++ /dev/null @@ -1,72 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - */ - -#ifndef __CROSSBAR_CONNECTIONS_H__ -#define __CROSSBAR_CONNECTIONS_H__ - -#define NUM_CON_VSC3316 8 -#define NUM_CON_VSC3308 4 - -static const int8_t vsc16_tx_amc[8][2] = { {15, 3}, {0, 2}, {7, 4}, {9, 10}, - {5, 11}, {4, 5}, {2, 6}, {12, 9} }; - -static int8_t vsc16_tx_sfp[8][2] = { {15, 7}, {0, 1}, {7, 8}, {9, 0}, - {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; - -static int8_t vsc16_tx_4sfp_sgmii_12_56[8][2] = { {15, 7}, {0, 1}, - {7, 8}, {9, 0}, {2, 14}, {12, 15}, - {-1, -1}, {-1, -1} }; - -static const int8_t vsc16_tx_4sfp_sgmii_34[8][2] = { {15, 7}, {0, 1}, - {7, 8}, {9, 0}, {5, 14}, {4, 15}, - {-1, -1}, {-1, -1} }; - -static int8_t vsc16_tx_sfp_sgmii_aurora[8][2] = { {15, 7}, {0, 1}, - {7, 8}, {9, 0}, {5, 14}, - {4, 15}, {2, 12}, {12, 13} }; - -#ifdef CONFIG_ARCH_B4420 -static int8_t vsc16_tx_sgmii_lane_cd[8][2] = { {5, 14}, {4, 15}, - {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; -#endif - -static const int8_t vsc16_tx_aurora[8][2] = { {2, 13}, {12, 12}, {-1, -1}, - {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; - -static const int8_t vsc16_rx_amc[8][2] = { {3, 15}, {2, 1}, {4, 8}, {10, 9}, - {11, 11}, {5, 10}, {6, 3}, {9, 12} }; - -static int8_t vsc16_rx_sfp[8][2] = { {8, 15}, {0, 1}, {7, 8}, {1, 9}, - {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; - -static int8_t vsc16_rx_4sfp_sgmii_12_56[8][2] = { {8, 15}, {0, 1}, - {7, 8}, {1, 9}, {14, 3}, {15, 12}, - {-1, -1}, {-1, -1} }; - -static const int8_t vsc16_rx_4sfp_sgmii_34[8][2] = { {8, 15}, {0, 1}, - {7, 8}, {1, 9}, {14, 11}, {15, 10}, - {-1, -1}, {-1, -1} }; - -static int8_t vsc16_rx_sfp_sgmii_aurora[8][2] = { {8, 15}, {0, 1}, - {7, 8}, {1, 9}, {14, 11}, - {15, 10}, {13, 3}, {12, 12} }; - -#ifdef CONFIG_ARCH_B4420 -static int8_t vsc16_rx_sgmii_lane_cd[8][2] = { {14, 11}, {15, 10}, - {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; -#endif - -static const int8_t vsc16_rx_aurora[8][2] = { {13, 3}, {12, 12}, {-1, -1}, - {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} }; - -static const int8_t vsc08_tx_amc[4][2] = { {2, 2}, {3, 3}, {7, 4}, {1, 5} }; - -static const int8_t vsc08_tx_sfp[4][2] = { {2, 1}, {3, 0}, {7, 6}, {1, 7} }; - -static const int8_t vsc08_rx_amc[4][2] = { {2, 3}, {3, 4}, {4, 7}, {5, 1} }; - -static const int8_t vsc08_rx_sfp[4][2] = { {1, 3}, {0, 4}, {6, 7}, {7, 1} }; - -#endif diff --git a/board/freescale/b4860qds/b4860qds_qixis.h b/board/freescale/b4860qds/b4860qds_qixis.h deleted file mode 100644 index d4299d8af1..0000000000 --- a/board/freescale/b4860qds/b4860qds_qixis.h +++ /dev/null @@ -1,28 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - */ - -#ifndef __B4860QDS_QIXIS_H__ -#define __B4860QDS_QIXIS_H__ - -/* Definitions of QIXIS Registers for B4860QDS */ - -/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */ -#define BRDCFG4_EMISEL_MASK 0xE0 -#define BRDCFG4_EMISEL_SHIFT 5 - -/* CLK */ -#define QIXIS_CLK_66 0x0 -#define QIXIS_CLK_100 0x1 -#define QIXIS_CLK_125 0x2 -#define QIXIS_CLK_133 0x3 - -#define QIXIS_SRDS1CLK_122 0x5a -#define QIXIS_SRDS1CLK_125 0x5e - -/* SGMII */ -#define PHY_BASE_ADDR 0x18 -#define PORT_NUM 0x04 -#define REGNUM 0x00 -#endif diff --git a/board/freescale/b4860qds/b4_pbi.cfg b/board/freescale/b4860qds/b4_pbi.cfg deleted file mode 100644 index 05377bac5b..0000000000 --- a/board/freescale/b4860qds/b4_pbi.cfg +++ /dev/null @@ -1,30 +0,0 @@ -#PBI commands -#Initialize CPC1 -09010000 00200400 -09138000 00000000 -091380c0 00000100 -#Configure CPC1 as 512KB SRAM -09010100 00000000 -09010104 fff80009 -09010f00 08000000 -09010000 80000000 -#Configure LAW for CPC1 -09000d00 00000000 -09000d04 fff80000 -09000d08 81000012 -#Configure alternate space -09000010 00000000 -09000014 ff000000 -09000018 81000000 -#Configure SPI controller -09110000 80000403 -09110020 2d170008 -09110024 00100008 -09110028 00100008 -0911002c 00100008 -#slowing down the MDC clock to make it <= 2.5 MHZ -094fc030 00008148 -094fd030 00008148 -#Flush PBL data -09138000 00000000 -091380c0 00000000 diff --git a/board/freescale/b4860qds/b4_rcw.cfg b/board/freescale/b4860qds/b4_rcw.cfg deleted file mode 100644 index 597d3914ca..0000000000 --- a/board/freescale/b4860qds/b4_rcw.cfg +++ /dev/null @@ -1,7 +0,0 @@ -#PBL preamble and RCW header -aa55aa55 010e0100 -# serdes protocol 0x2A_0x98 -140e0018 0f001218 00000000 00000000 -54980000 9000a000 e8104000 a9000000 -01000000 00000000 00000000 0001b1f8 -00000000 14000020 00000000 00000011 diff --git a/board/freescale/b4860qds/ddr.c b/board/freescale/b4860qds/ddr.c deleted file mode 100644 index d3aa349ddf..0000000000 --- a/board/freescale/b4860qds/ddr.c +++ /dev/null @@ -1,267 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -dimm_params_t ddr_raw_timing = { - .n_ranks = 2, - .rank_density = 2147483648u, - .capacity = 4294967296u, - .primary_sdram_width = 64, - .ec_sdram_width = 8, - .registered_dimm = 0, - .mirrored_dimm = 1, - .n_row_addr = 15, - .n_col_addr = 10, - .n_banks_per_sdram_device = 8, - .edc_config = 2, /* ECC */ - .burst_lengths_bitmask = 0x0c, - - .tckmin_x_ps = 1071, - .caslat_x = 0x2fe << 4, /* 5,6,7,8,9,10,11,13 */ - .taa_ps = 13910, - .twr_ps = 15000, - .trcd_ps = 13910, - .trrd_ps = 6000, - .trp_ps = 13910, - .tras_ps = 34000, - .trc_ps = 48910, - .trfc_ps = 260000, - .twtr_ps = 7500, - .trtp_ps = 7500, - .refresh_rate_ps = 7800000, - .tfaw_ps = 35000, -}; - -int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, - unsigned int controller_number, - unsigned int dimm_number) -{ - const char dimm_model[] = "RAW timing DDR"; - - if ((controller_number == 0) && (dimm_number == 0)) { - memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); - memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); - memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); - } - - return 0; -} - -struct board_specific_parameters { - u32 n_ranks; - u32 datarate_mhz_high; - u32 clk_adjust; - u32 wrlvl_start; - u32 wrlvl_ctl_2; - u32 wrlvl_ctl_3; - u32 cpo; - u32 write_data_delay; - u32 force_2t; -}; - -/* - * This table contains all valid speeds we want to override with board - * specific parameters. datarate_mhz_high values need to be in ascending order - * for each n_ranks group. - */ -static const struct board_specific_parameters udimm0[] = { - /* - * memory controller 0 - * num| hi| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T - * ranks| mhz|adjst| start | ctl2 | ctl3 | |delay | - */ - {2, 1350, 4, 7, 0x09080807, 0x07060607, 0xff, 2, 0}, - {2, 1666, 4, 7, 0x09080806, 0x06050607, 0xff, 2, 0}, - {2, 1900, 3, 7, 0x08070706, 0x06040507, 0xff, 2, 0}, - {1, 1350, 4, 7, 0x09080807, 0x07060607, 0xff, 2, 0}, - {1, 1700, 4, 7, 0x09080806, 0x06050607, 0xff, 2, 0}, - {1, 1900, 3, 7, 0x08070706, 0x06040507, 0xff, 2, 0}, - {} -}; - -static const struct board_specific_parameters *udimms[] = { - udimm0, -}; - -void fsl_ddr_board_options(memctl_options_t *popts, - dimm_params_t *pdimm, - unsigned int ctrl_num) -{ - const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; - ulong ddr_freq; - - if (ctrl_num > 2) { - printf("Not supported controller number %d\n", ctrl_num); - return; - } - if (!pdimm->n_ranks) - return; - - pbsp = udimms[0]; - - - /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr - * freqency and n_banks specified in board_specific_parameters table. - */ - ddr_freq = get_ddr_freq(0) / 1000000; - while (pbsp->datarate_mhz_high) { - if (pbsp->n_ranks == pdimm->n_ranks) { - if (ddr_freq <= pbsp->datarate_mhz_high) { - popts->cpo_override = pbsp->cpo; - popts->write_data_delay = - pbsp->write_data_delay; - popts->clk_adjust = pbsp->clk_adjust; - popts->wrlvl_start = pbsp->wrlvl_start; - popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; - popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - popts->twot_en = pbsp->force_2t; - goto found; - } - pbsp_highest = pbsp; - } - pbsp++; - } - - if (pbsp_highest) { - printf("Error: board specific timing not found " - "for data rate %lu MT/s\n" - "Trying to use the highest speed (%u) parameters\n", - ddr_freq, pbsp_highest->datarate_mhz_high); - popts->cpo_override = pbsp_highest->cpo; - popts->write_data_delay = pbsp_highest->write_data_delay; - popts->clk_adjust = pbsp_highest->clk_adjust; - popts->wrlvl_start = pbsp_highest->wrlvl_start; - popts->twot_en = pbsp_highest->force_2t; - } else { - panic("DIMM is not supported by this board"); - } -found: - /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed - */ - popts->half_strength_driver_enable = 0; - /* - * Write leveling override - */ - popts->wrlvl_override = 1; - popts->wrlvl_sample = 0xf; - - /* - * Rtt and Rtt_WR override - */ - popts->rtt_override = 0; - - /* Enable ZQ calibration */ - popts->zq_en = 1; - - /* DHC_EN =1, ODT = 75 Ohm */ - popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); - popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); - - /* optimize cpo for erratum A-009942 */ - popts->cpo_sample = 0x3e; -} - -int dram_init(void) -{ - phys_size_t dram_size; - -#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) - puts("Initializing....using SPD\n"); - dram_size = fsl_ddr_sdram(); -#else - dram_size = fsl_ddr_sdram_size(); -#endif - dram_size = setup_ddr_tlbs(dram_size / 0x100000); - dram_size *= 0x100000; - - gd->ram_size = dram_size; - - return 0; -} - -unsigned long long step_assign_addresses(fsl_ddr_info_t *pinfo, - unsigned int dbw_cap_adj[]) -{ - int i, j; - unsigned long long total_mem, current_mem_base, total_ctlr_mem; - unsigned long long rank_density, ctlr_density = 0; - - current_mem_base = 0ull; - total_mem = 0; - /* - * This board has soldered DDR chips. DDRC1 has two rank. - * DDRC2 has only one rank. - * Assigning DDRC2 to lower address and DDRC1 to higher address. - */ - if (pinfo->memctl_opts[0].memctl_interleaving) { - rank_density = pinfo->dimm_params[0][0].rank_density >> - dbw_cap_adj[0]; - ctlr_density = rank_density; - - debug("rank density is 0x%llx, ctlr density is 0x%llx\n", - rank_density, ctlr_density); - for (i = CONFIG_SYS_NUM_DDR_CTLRS - 1; i >= 0; i--) { - switch (pinfo->memctl_opts[i].memctl_interleaving_mode) { - case FSL_DDR_CACHE_LINE_INTERLEAVING: - case FSL_DDR_PAGE_INTERLEAVING: - case FSL_DDR_BANK_INTERLEAVING: - case FSL_DDR_SUPERBANK_INTERLEAVING: - total_ctlr_mem = 2 * ctlr_density; - break; - default: - panic("Unknown interleaving mode"); - } - pinfo->common_timing_params[i].base_address = - current_mem_base; - pinfo->common_timing_params[i].total_mem = - total_ctlr_mem; - total_mem = current_mem_base + total_ctlr_mem; - debug("ctrl %d base 0x%llx\n", i, current_mem_base); - debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); - } - } else { - /* - * Simple linear assignment if memory - * controllers are not interleaved. - */ - for (i = CONFIG_SYS_NUM_DDR_CTLRS - 1; i >= 0; i--) { - total_ctlr_mem = 0; - pinfo->common_timing_params[i].base_address = - current_mem_base; - for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { - /* Compute DIMM base addresses. */ - unsigned long long cap = - pinfo->dimm_params[i][j].capacity; - pinfo->dimm_params[i][j].base_address = - current_mem_base; - debug("ctrl %d dimm %d base 0x%llx\n", - i, j, current_mem_base); - current_mem_base += cap; - total_ctlr_mem += cap; - } - debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); - pinfo->common_timing_params[i].total_mem = - total_ctlr_mem; - total_mem += total_ctlr_mem; - } - } - debug("Total mem by %s is 0x%llx\n", __func__, total_mem); - - return total_mem; -} diff --git a/board/freescale/b4860qds/eth_b4860qds.c b/board/freescale/b4860qds/eth_b4860qds.c deleted file mode 100644 index 6d5f3d1fda..0000000000 --- a/board/freescale/b4860qds/eth_b4860qds.c +++ /dev/null @@ -1,454 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - * Author: Sandeep Kumar Singh - */ - -/* This file is based on board/freescale/corenet_ds/eth_superhydra.c */ - -/* - * This file handles the board muxing between the Fman Ethernet MACs and - * the RGMII/SGMII/XGMII PHYs on a Freescale B4860 "Centaur". The SGMII - * PHYs are the two on-board 1Gb ports. There are no RGMII PHY on board. - * The 10Gb XGMII PHY is provided via the XAUI riser card. There is only - * one Fman device on B4860. The SERDES configuration is used to determine - * where the SGMII and XAUI cards exist, and also which Fman MACs are routed - * to which PHYs. So for a given Fman MAC, there is one and only PHY it - * connects to. MACs cannot be routed to PHYs dynamically. This configuration - * is done at boot time by reading SERDES protocol from RCW. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include "../common/ngpixis.h" -#include "../common/fman.h" -#include "../common/qixis.h" -#include "b4860qds_qixis.h" - -#define EMI_NONE 0xFFFFFFFF - -#ifdef CONFIG_FMAN_ENET - -/* - * Mapping of all 16 SERDES lanes to board slots. A value n(>0) will mean that - * lane at index is mapped to slot number n. A value of '0' will mean - * that the mapping must be determined dynamically, or that the lane maps to - * something other than a board slot - */ -static u8 lane_to_slot[] = { - 0, 0, 0, 0, - 0, 0, 0, 0, - 1, 1, 1, 1, - 0, 0, 0, 0 -}; - -/* - * This function initializes the lane_to_slot[] array. It reads RCW to check - * if Serdes2{E,F,G,H} is configured as slot 2 or as SFP and initializes - * lane_to_slot[] accordingly - */ -static void initialize_lane_to_slot(void) -{ - unsigned int serdes2_prtcl; - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - serdes2_prtcl = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS2_PRTCL; - serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; - debug("Initializing lane to slot: Serdes2 protocol: %x\n", - serdes2_prtcl); - - switch (serdes2_prtcl) { - case 0x17: - case 0x18: - /* - * Configuration: - * SERDES: 2 - * Lanes: A,B,C,D: SGMII - * Lanes: E,F: Aur - * Lanes: G,H: SRIO - */ - case 0x91: - /* - * Configuration: - * SERDES: 2 - * Lanes: A,B: SGMII - * Lanes: C,D: SRIO2 - * Lanes: E,F,G,H: XAUI2 - */ - case 0x93: - /* - * Configuration: - * SERDES: 2 - * Lanes: A,B,C,D: SGMII - * Lanes: E,F,G,H: XAUI2 - */ - case 0x98: - /* - * Configuration: - * SERDES: 2 - * Lanes: A,B,C,D: XAUI2 - * Lanes: E,F,G,H: XAUI2 - */ - case 0x9a: - /* - * Configuration: - * SERDES: 2 - * Lanes: A,B: PCI - * Lanes: C,D: SGMII - * Lanes: E,F,G,H: XAUI2 - */ - case 0x9e: - /* - * Configuration: - * SERDES: 2 - * Lanes: A,B,C,D: PCI - * Lanes: E,F,G,H: XAUI2 - */ - case 0xb1: - case 0xb2: - case 0x8c: - case 0x8d: - /* - * Configuration: - * SERDES: 2 - * Lanes: A,B,C,D: PCI - * Lanes: E,F: SGMII 3&4 - * Lanes: G,H: XFI - */ - case 0xc2: - /* - * Configuration: - * SERDES: 2 - * Lanes: A,B: SGMII - * Lanes: C,D: SRIO2 - * Lanes: E,F,G,H: XAUI2 - */ - lane_to_slot[12] = 2; - lane_to_slot[13] = lane_to_slot[12]; - lane_to_slot[14] = lane_to_slot[12]; - lane_to_slot[15] = lane_to_slot[12]; - break; - - default: - printf("Fman: Unsupported SerDes2 Protocol 0x%02x\n", - serdes2_prtcl); - break; - } - return; -} - -#endif /* #ifdef CONFIG_FMAN_ENET */ - -int board_eth_init(bd_t *bis) -{ -#ifdef CONFIG_FMAN_ENET - struct memac_mdio_info memac_mdio_info; - struct memac_mdio_info tg_memac_mdio_info; - unsigned int i; - unsigned int serdes1_prtcl, serdes2_prtcl; - int qsgmii; - struct mii_dev *bus; - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - serdes1_prtcl = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS1_PRTCL; - if (!serdes1_prtcl) { - printf("SERDES1 is not enabled\n"); - return 0; - } - serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; - debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl); - - serdes2_prtcl = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS2_PRTCL; - if (!serdes2_prtcl) { - printf("SERDES2 is not enabled\n"); - return 0; - } - serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; - debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl); - - printf("Initializing Fman\n"); - - initialize_lane_to_slot(); - - memac_mdio_info.regs = - (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; - memac_mdio_info.name = DEFAULT_FM_MDIO_NAME; - - /* Register the real 1G MDIO bus */ - fm_memac_mdio_init(bis, &memac_mdio_info); - - tg_memac_mdio_info.regs = - (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR; - tg_memac_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; - - /* Register the real 10G MDIO bus */ - fm_memac_mdio_init(bis, &tg_memac_mdio_info); - - /* - * Program the two on board DTSEC PHY addresses assuming that they are - * all SGMII. RGMII is not supported on this board. Setting SGMII 5 and - * 6 to on board SGMII phys - */ - fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR); - fm_info_set_phy_address(FM1_DTSEC6, CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR); - - switch (serdes1_prtcl) { - case 0x29: - case 0x2a: - /* Serdes 1: A-B SGMII, Configuring DTSEC 5 and 6 */ - debug("Set phy addresses for FM1_DTSEC5:%x, FM1_DTSEC6:%x\n", - CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR, - CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR); - fm_info_set_phy_address(FM1_DTSEC5, - CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR); - fm_info_set_phy_address(FM1_DTSEC6, - CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR); - break; -#ifdef CONFIG_ARCH_B4420 - case 0x17: - case 0x18: - /* Serdes 1: A-D SGMII, Configuring on board dual SGMII Phy */ - debug("Set phy addresses for FM1_DTSEC3:%x, FM1_DTSEC4:%x\n", - CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR, - CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR); - /* Fixing Serdes clock by programming FPGA register */ - QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125); - fm_info_set_phy_address(FM1_DTSEC3, - CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR); - fm_info_set_phy_address(FM1_DTSEC4, - CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR); - break; -#endif - default: - printf("Fman: Unsupported SerDes1 Protocol 0x%02x\n", - serdes1_prtcl); - break; - } - switch (serdes2_prtcl) { - case 0x17: - case 0x18: - debug("Set phy address on SGMII Riser for FM1_DTSEC1:%x\n", - CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC1, - CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC2, - CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC3, - CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC4, - CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR); - break; - case 0x48: - case 0x49: - debug("Set phy address on SGMII Riser for FM1_DTSEC1:%x\n", - CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC1, - CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC2, - CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC3, - CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR); - break; - case 0xb1: - case 0xb2: - case 0x8c: - case 0x8d: - debug("Set phy addresses on SGMII Riser for FM1_DTSEC1:%x\n", - CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC3, - CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC4, - CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR); - /* - * XFI does not need a PHY to work, but to make U-Boot - * happy, assign a fake PHY address for a XFI port. - */ - fm_info_set_phy_address(FM1_10GEC1, 0); - fm_info_set_phy_address(FM1_10GEC2, 1); - break; - case 0x98: - /* XAUI in Slot1 and Slot2 */ - debug("Set phy address of AMC2PEX-2S for FM1_10GEC1:%x\n", - CONFIG_SYS_FM1_10GEC1_PHY_ADDR); - fm_info_set_phy_address(FM1_10GEC1, - CONFIG_SYS_FM1_10GEC1_PHY_ADDR); - debug("Set phy address of AMC2PEX-2S for FM1_10GEC2:%x\n", - CONFIG_SYS_FM1_10GEC2_PHY_ADDR); - fm_info_set_phy_address(FM1_10GEC2, - CONFIG_SYS_FM1_10GEC2_PHY_ADDR); - break; - case 0x9E: - /* XAUI in Slot2 */ - debug("Sett phy address of AMC2PEX-2S for FM1_10GEC2:%x\n", - CONFIG_SYS_FM1_10GEC2_PHY_ADDR); - fm_info_set_phy_address(FM1_10GEC2, - CONFIG_SYS_FM1_10GEC2_PHY_ADDR); - break; - default: - printf("Fman: Unsupported SerDes2 Protocol 0x%02x\n", - serdes2_prtcl); - break; - } - - /*set PHY address for QSGMII Riser Card on slot2*/ - bus = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME); - qsgmii = is_qsgmii_riser_card(bus, PHY_BASE_ADDR, PORT_NUM, REGNUM); - - if (qsgmii) { - switch (serdes2_prtcl) { - case 0xb2: - case 0x8d: - fm_info_set_phy_address(FM1_DTSEC3, PHY_BASE_ADDR); - fm_info_set_phy_address(FM1_DTSEC4, PHY_BASE_ADDR + 1); - break; - default: - break; - } - } - - for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { - int idx = i - FM1_DTSEC1; - - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_SGMII: - fm_info_set_mdio(i, - miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME)); - break; - case PHY_INTERFACE_MODE_NONE: - fm_info_set_phy_address(i, 0); - break; - default: - printf("Fman1: DTSEC%u set to unknown interface %i\n", - idx + 1, fm_info_get_enet_if(i)); - fm_info_set_phy_address(i, 0); - break; - } - } - - for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) { - int idx = i - FM1_10GEC1; - - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_XGMII: - fm_info_set_mdio(i, - miiphy_get_dev_by_name - (DEFAULT_FM_TGEC_MDIO_NAME)); - break; - case PHY_INTERFACE_MODE_NONE: - fm_info_set_phy_address(i, 0); - break; - default: - printf("Fman1: TGEC%u set to unknown interface %i\n", - idx + 1, fm_info_get_enet_if(i)); - fm_info_set_phy_address(i, 0); - break; - } - } - - cpu_eth_init(bis); -#endif - - return pci_eth_init(bis); -} - -void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, - enum fm_port port, int offset) -{ - int phy; - char alias[32]; - struct fixed_link f_link; - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 prtcl2 = in_be32(&gur->rcwsr[4]) & FSL_CORENET2_RCWSR4_SRDS2_PRTCL; - - prtcl2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; - - if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) { - phy = fm_info_get_phy_address(port); - - sprintf(alias, "phy_sgmii_%x", phy); - fdt_set_phy_handle(fdt, compat, addr, alias); - fdt_status_okay_by_alias(fdt, alias); - } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) { - /* check if it's XFI interface for 10g */ - switch (prtcl2) { - case 0x80: - case 0x81: - case 0x82: - case 0x83: - case 0x84: - case 0x85: - case 0x86: - case 0x87: - case 0x88: - case 0x89: - case 0x8a: - case 0x8b: - case 0x8c: - case 0x8d: - case 0x8e: - case 0xb1: - case 0xb2: - f_link.phy_id = port; - f_link.duplex = 1; - f_link.link_speed = 10000; - f_link.pause = 0; - f_link.asym_pause = 0; - - fdt_delprop(fdt, offset, "phy-handle"); - fdt_setprop(fdt, offset, "fixed-link", &f_link, - sizeof(f_link)); - break; - case 0x98: /* XAUI interface */ - strcpy(alias, "phy_xaui_slot1"); - fdt_status_okay_by_alias(fdt, alias); - - strcpy(alias, "phy_xaui_slot2"); - fdt_status_okay_by_alias(fdt, alias); - break; - case 0x9e: /* XAUI interface */ - case 0x9a: - case 0x93: - case 0x91: - strcpy(alias, "phy_xaui_slot1"); - fdt_status_okay_by_alias(fdt, alias); - break; - case 0x97: /* XAUI interface */ - case 0xc3: - strcpy(alias, "phy_xaui_slot2"); - fdt_status_okay_by_alias(fdt, alias); - break; - default: - break; - } - } -} - -/* - * Set status to disabled for unused ethernet node - */ -void fdt_fixup_board_enet(void *fdt) -{ - int i; - char alias[32]; - - for (i = FM1_DTSEC1; i <= FM1_10GEC2; i++) { - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_NONE: - sprintf(alias, "ethernet%u", i); - fdt_status_disabled_by_alias(fdt, alias); - break; - default: - break; - } - } -} diff --git a/board/freescale/b4860qds/law.c b/board/freescale/b4860qds/law.c deleted file mode 100644 index b39d720068..0000000000 --- a/board/freescale/b4860qds/law.c +++ /dev/null @@ -1,28 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - */ - -#include -#include -#include - -struct law_entry law_table[] = { - SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), -#ifdef CONFIG_SYS_BMAN_MEM_PHYS - SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), -#endif -#ifdef CONFIG_SYS_QMAN_MEM_PHYS - SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), -#endif - SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), -#ifdef CONFIG_SYS_DCSRBAR_PHYS - /* Limit DCSR to 32M to access NPC Trace Buffer */ - SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR), -#endif -#ifdef CONFIG_SYS_NAND_BASE_PHYS - SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), -#endif -}; - -int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/b4860qds/pci.c b/board/freescale/b4860qds/pci.c deleted file mode 100644 index 45dd461e77..0000000000 --- a/board/freescale/b4860qds/pci.c +++ /dev/null @@ -1,23 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -void pci_init_board(void) -{ - fsl_pcie_init_board(0); -} - -void pci_of_setup(void *blob, bd_t *bd) -{ - FT_FSL_PCI_SETUP; -} diff --git a/board/freescale/b4860qds/spl.c b/board/freescale/b4860qds/spl.c deleted file mode 100644 index fe5ce35013..0000000000 --- a/board/freescale/b4860qds/spl.c +++ /dev/null @@ -1,119 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* Copyright 2013 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include "../common/qixis.h" -#include "b4860qds_qixis.h" - -DECLARE_GLOBAL_DATA_PTR; - -phys_size_t get_effective_memsize(void) -{ - return CONFIG_SYS_L3_SIZE; -} - -unsigned long get_board_sys_clk(void) -{ - u8 sysclk_conf = QIXIS_READ(brdcfg[1]); - - switch ((sysclk_conf & 0x0C) >> 2) { - case QIXIS_CLK_100: - return 100000000; - case QIXIS_CLK_125: - return 125000000; - case QIXIS_CLK_133: - return 133333333; - } - return 66666666; -} - -unsigned long get_board_ddr_clk(void) -{ - u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); - - switch (ddrclk_conf & 0x03) { - case QIXIS_CLK_100: - return 100000000; - case QIXIS_CLK_125: - return 125000000; - case QIXIS_CLK_133: - return 133333333; - } - return 66666666; -} - -void board_init_f(ulong bootflag) -{ - u32 plat_ratio, sys_clk, uart_clk; - ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; - - /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */ - memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t)); - - /* Update GD pointer */ - gd = (gd_t *)(CONFIG_SPL_GD_ADDR); - - /* compiler optimization barrier needed for GCC >= 3.4 */ - __asm__ __volatile__("" : : : "memory"); - - console_init_f(); - - /* initialize selected port with appropriate baud rate */ - sys_clk = get_board_sys_clk(); - plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f; - uart_clk = sys_clk * plat_ratio / 2; - - NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, - uart_clk / 16 / CONFIG_BAUDRATE); - - relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0); -} - -void board_init_r(gd_t *gd, ulong dest_addr) -{ - bd_t *bd; - - bd = (bd_t *)(gd + sizeof(gd_t)); - memset(bd, 0, sizeof(bd_t)); - gd->bd = bd; - bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR; - bd->bi_memsize = CONFIG_SYS_L3_SIZE; - - arch_cpu_init(); - get_clocks(); - mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, - CONFIG_SPL_RELOC_MALLOC_SIZE); - gd->flags |= GD_FLG_FULL_MALLOC_INIT; - -#ifndef CONFIG_SPL_NAND_BOOT - env_init(); - env_relocate(); -#else - /* relocate environment function pointers etc. */ - nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, - (uchar *)SPL_ENV_ADDR); - gd->env_addr = (ulong)(SPL_ENV_ADDR); - gd->env_valid = ENV_VALID; -#endif - - i2c_init_all(); - - puts("\n\n"); - - dram_init(); - -#ifdef CONFIG_SPL_NAND_BOOT - nand_boot(); -#endif -} diff --git a/board/freescale/b4860qds/tlb.c b/board/freescale/b4860qds/tlb.c deleted file mode 100644 index 68e2295cb5..0000000000 --- a/board/freescale/b4860qds/tlb.c +++ /dev/null @@ -1,154 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - */ - -#include -#include - -struct fsl_e_tlb_entry tlb_table[] = { - /* TLB 0 - for temp stack in cache */ - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, - CONFIG_SYS_INIT_RAM_ADDR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - - /* TLB 1 */ - /* *I*** - Covers boot page */ -#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) - /* - * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the - * SRAM is at 0xfff00000, it covered the 0xfffff000. - */ - SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_1M, 1), -#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) - /* - * SRIO_PCIE_BOOT-SLAVE. When slave boot, the address of the - * space is at 0xfff00000, it covered the 0xfffff000. - */ - SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR, - CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, - 0, 0, BOOKE_PAGESZ_1M, 1), -#else - SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_4K, 1), -#endif - - /* *I*G* - CCSRBAR */ - SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 1, BOOKE_PAGESZ_16M, 1), - - /* *I*G* - Flash, localbus */ - /* This will be changed to *I*G* after relocation to RAM. */ - SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, - MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, - 0, 2, BOOKE_PAGESZ_256M, 1), - -#ifndef CONFIG_SPL_BUILD - /* *I*G* - PCI */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 3, BOOKE_PAGESZ_256M, 1), - - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x10000000, - CONFIG_SYS_PCIE1_MEM_PHYS + 0x10000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 4, BOOKE_PAGESZ_256M, 1), - - /* *I*G* - PCI I/O */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 5, BOOKE_PAGESZ_64K, 1), - - /* Bman/Qman */ -#ifdef CONFIG_SYS_BMAN_MEM_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 6, BOOKE_PAGESZ_16M, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, - CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 7, BOOKE_PAGESZ_16M, 1), -#endif -#ifdef CONFIG_SYS_QMAN_MEM_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 8, BOOKE_PAGESZ_16M, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, - CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 9, BOOKE_PAGESZ_16M, 1), -#endif -#endif -#ifdef CONFIG_SYS_DCSRBAR_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 10, BOOKE_PAGESZ_32M, 1), -#endif -#ifdef CONFIG_SYS_NAND_BASE - /* - * *I*G - NAND - */ - SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 11, BOOKE_PAGESZ_64K, 1), -#endif - SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 12, BOOKE_PAGESZ_4K, 1), - - /* - * *I*G - SRIO - * entry 14 and 15 has been used hard coded, they will be disabled - * in cpu_init_f, so we use entry 16 for SRIO2. - */ -#ifndef CONFIG_SPL_BUILD -#ifdef CONFIG_SYS_SRIO1_MEM_PHYS - /* *I*G* - SRIO1 */ - SET_TLB_ENTRY(1, CONFIG_SYS_SRIO1_MEM_VIRT, CONFIG_SYS_SRIO1_MEM_PHYS, - MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 13, BOOKE_PAGESZ_256M, 1), -#endif -#ifdef CONFIG_SYS_SRIO2_MEM_PHYS - /* *I*G* - SRIO2 */ - SET_TLB_ENTRY(1, CONFIG_SYS_SRIO2_MEM_VIRT, CONFIG_SYS_SRIO2_MEM_PHYS, - MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 16, BOOKE_PAGESZ_256M, 1), -#endif -#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE - /* - * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for - * fetching ucode and ENV from master - */ - SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR, - CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, - 0, 17, BOOKE_PAGESZ_1M, 1), -#endif -#endif - -#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD) - SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, - 0, 17, BOOKE_PAGESZ_2G, 1) -#endif -}; - -int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/configs/B4420QDS_NAND_defconfig b/configs/B4420QDS_NAND_defconfig deleted file mode 100644 index 6fcb51a1cd..0000000000 --- a/configs/B4420QDS_NAND_defconfig +++ /dev/null @@ -1,69 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x140000 -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_B4420QDS=y -CONFIG_SYS_CUSTOM_LDSCRIPT=y -CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL" -CONFIG_BOOTDELAY=10 -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_NAND_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_SPL_NAND_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_ENV_IS_IN_NAND=y -CONFIG_FSL_CAAM=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_MTD_RAW_NAND=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NAND=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/B4420QDS_SPIFLASH_defconfig b/configs/B4420QDS_SPIFLASH_defconfig deleted file mode 100644 index 5dc72cb3f2..0000000000 --- a/configs/B4420QDS_SPIFLASH_defconfig +++ /dev/null @@ -1,55 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xFFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x100000 -CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_MPC85xx=y -CONFIG_TARGET_B4420QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPIFLASH" -CONFIG_BOOTDELAY=10 -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_FSL_CAAM=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/B4420QDS_defconfig b/configs/B4420QDS_defconfig deleted file mode 100644 index 5f9a88adfa..0000000000 --- a/configs/B4420QDS_defconfig +++ /dev/null @@ -1,53 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_MPC85xx=y -CONFIG_TARGET_B4420QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xEFF20000 -CONFIG_FSL_CAAM=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/B4860QDS_NAND_defconfig b/configs/B4860QDS_NAND_defconfig deleted file mode 100644 index 0874acd83e..0000000000 --- a/configs/B4860QDS_NAND_defconfig +++ /dev/null @@ -1,69 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x140000 -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_B4860QDS=y -CONFIG_SYS_CUSTOM_LDSCRIPT=y -CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL" -CONFIG_BOOTDELAY=10 -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_NAND_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_SPL_NAND_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_ENV_IS_IN_NAND=y -CONFIG_FSL_CAAM=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_MTD_RAW_NAND=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NAND=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/B4860QDS_SECURE_BOOT_defconfig b/configs/B4860QDS_SECURE_BOOT_defconfig deleted file mode 100644 index 4d7bf5dc39..0000000000 --- a/configs/B4860QDS_SECURE_BOOT_defconfig +++ /dev/null @@ -1,56 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_NXP_ESBC=y -CONFIG_MPC85xx=y -CONFIG_TARGET_B4860QDS=y -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_DM=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_RSA=y -CONFIG_SPL_RSA=y -CONFIG_RSA_SOFTWARE_EXP=y -CONFIG_OF_LIBFDT=y diff --git a/configs/B4860QDS_SPIFLASH_defconfig b/configs/B4860QDS_SPIFLASH_defconfig deleted file mode 100644 index 566076543f..0000000000 --- a/configs/B4860QDS_SPIFLASH_defconfig +++ /dev/null @@ -1,55 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xFFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x100000 -CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_MPC85xx=y -CONFIG_TARGET_B4860QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPIFLASH" -CONFIG_BOOTDELAY=10 -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_FSL_CAAM=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/B4860QDS_SRIO_PCIE_BOOT_defconfig b/configs/B4860QDS_SRIO_PCIE_BOOT_defconfig deleted file mode 100644 index 58195adcbc..0000000000 --- a/configs/B4860QDS_SRIO_PCIE_BOOT_defconfig +++ /dev/null @@ -1,49 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xFFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_MPC85xx=y -CONFIG_TARGET_B4860QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="SRIO_PCIE_BOOT_SLAVE" -CONFIG_BOOTDELAY=10 -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_GREPENV=y -# CONFIG_CMD_FLASH is not set -CONFIG_CMD_I2C=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_ENV_IS_IN_REMOTE=y -CONFIG_ENV_ADDR=0xFFE20000 -CONFIG_FSL_CAAM=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_REMOTE=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/B4860QDS_defconfig b/configs/B4860QDS_defconfig deleted file mode 100644 index 68ff6ed953..0000000000 --- a/configs/B4860QDS_defconfig +++ /dev/null @@ -1,53 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_MPC85xx=y -CONFIG_TARGET_B4860QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xEFF20000 -CONFIG_FSL_CAAM=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h deleted file mode 100644 index a515bf9530..0000000000 --- a/include/configs/B4860QDS.h +++ /dev/null @@ -1,759 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include - -/* - * B4860 QDS board configuration file - */ -#ifdef CONFIG_RAMBOOT_PBL -#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/b4860qds/b4_pbi.cfg -#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/b4860qds/b4_rcw.cfg -#ifndef CONFIG_MTD_RAW_NAND -#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#else -#define CONFIG_SPL_FLUSH_IMAGE -#define CONFIG_SPL_PAD_TO 0x40000 -#define CONFIG_SPL_MAX_SIZE 0x28000 -#define RESET_VECTOR_OFFSET 0x27FFC -#define BOOT_PAGE_OFFSET 0x27000 -#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 -#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 -#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SPL_SKIP_RELOCATE -#define CONFIG_SPL_COMMON_INIT_DDR -#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE -#endif -#endif -#endif - -#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE -/* Set 1M boot space */ -#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) -#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ - (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) -#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#endif - -/* High Level Configuration Options */ -#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ - -#ifndef CONFIG_RESET_VECTOR_ADDRESS -#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc -#endif - -#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ -#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS -#define CONFIG_PCIE1 /* PCIE controller 1 */ -#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ -#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ - -#ifndef CONFIG_ARCH_B4420 -#define CONFIG_SYS_SRIO -#define CONFIG_SRIO1 /* SRIO port 1 */ -#define CONFIG_SRIO2 /* SRIO port 2 */ -#define CONFIG_SRIO_PCIE_BOOT_MASTER -#endif - -/* I2C bus multiplexer */ -#define I2C_MUX_PCA_ADDR 0x77 - -/* VSC Crossbar switches */ -#define CONFIG_VSC_CROSSBAR -#define I2C_CH_DEFAULT 0x8 -#define I2C_CH_VSC3316 0xc -#define I2C_CH_VSC3308 0xd - -#define VSC3316_TX_ADDRESS 0x70 -#define VSC3316_RX_ADDRESS 0x71 -#define VSC3308_TX_ADDRESS 0x02 -#define VSC3308_RX_ADDRESS 0x03 - -/* IDT clock synthesizers */ -#define CONFIG_IDT8T49N222A -#define I2C_CH_IDT 0x9 - -#define IDT_SERDES1_ADDRESS 0x6E -#define IDT_SERDES2_ADDRESS 0x6C - -/* Voltage monitor on channel 2*/ -#define I2C_MUX_CH_VOL_MONITOR 0xa -#define I2C_VOL_MONITOR_ADDR 0x40 -#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 -#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 -#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 - -#define CONFIG_ZM7300 -#define I2C_MUX_CH_DPM 0xa -#define I2C_DPM_ADDR 0x28 - -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_SPIFLASH) -#elif defined(CONFIG_SDCARD) -#define CONFIG_SYS_MMC_ENV_DEV 0 -#endif - -#ifndef __ASSEMBLY__ -unsigned long get_board_sys_clk(void); -unsigned long get_board_ddr_clk(void); -#endif -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ -#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_SYS_CACHE_STASHING -#define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_DDR_ECC -#ifdef CONFIG_DDR_ECC -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER -#define CONFIG_MEM_INIT_VALUE 0xdeadbeef -#endif - -#define CONFIG_ENABLE_36BIT_PHYS - -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_ADDR_MAP -#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ -#endif - -#if 0 -#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ -#endif - -/* - * Config the L3 Cache as L3 SRAM - */ -#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 -#define CONFIG_SYS_L3_SIZE 256 << 10 -#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) -#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) -#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) -#define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10) -#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) - -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_DCSRBAR 0xf0000000 -#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull -#endif - -/* EEPROM */ -#define CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_NXID -#define CONFIG_SYS_EEPROM_BUS_NUM 0 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 - -/* - * DDR Setup - */ -#define CONFIG_VERY_BIG_RAM -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) - -#define CONFIG_DDR_SPD -#define CONFIG_SYS_DDR_RAW_TIMING - -#define CONFIG_SYS_SPD_BUS_NUM 0 -#define SPD_EEPROM_ADDRESS1 0x51 -#define SPD_EEPROM_ADDRESS2 0x53 - -#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 -#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ - -/* - * IFC Definitions - */ -#define CONFIG_SYS_FLASH_BASE 0xe0000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) -#else -#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE -#endif - -#define CONFIG_SYS_NOR0_CSPR_EXT (0xf) -#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ - + 0x8000000) | \ - CSPR_PORT_SIZE_16 | \ - CSPR_MSEL_NOR | \ - CSPR_V) -#define CONFIG_SYS_NOR1_CSPR_EXT (0xf) -#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ - CSPR_PORT_SIZE_16 | \ - CSPR_MSEL_NOR | \ - CSPR_V) -#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) -/* NOR Flash Timing Params */ -#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(4) -#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x01) | \ - FTIM0_NOR_TEADC(0x04) | \ - FTIM0_NOR_TEAHC(0x20)) -#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ - FTIM1_NOR_TRAD_NOR(0x1A) |\ - FTIM1_NOR_TSEQRAD_NOR(0x13)) -#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x01) | \ - FTIM2_NOR_TCH(0x0E) | \ - FTIM2_NOR_TWPH(0x0E) | \ - FTIM2_NOR_TWP(0x1c)) -#define CONFIG_SYS_NOR_FTIM3 0x0 - -#define CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ - + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} - -#define CONFIG_FSL_QIXIS /* use common QIXIS code */ -#define CONFIG_FSL_QIXIS_V2 -#define QIXIS_BASE 0xffdf0000 -#ifdef CONFIG_PHYS_64BIT -#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) -#else -#define QIXIS_BASE_PHYS QIXIS_BASE -#endif -#define QIXIS_LBMAP_SWITCH 0x01 -#define QIXIS_LBMAP_MASK 0x0f -#define QIXIS_LBMAP_SHIFT 0 -#define QIXIS_LBMAP_DFLTBANK 0x00 -#define QIXIS_LBMAP_ALTBANK 0x02 -#define QIXIS_RST_CTL_RESET 0x31 -#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 -#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 -#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 - -#define CONFIG_SYS_CSPR3_EXT (0xf) -#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ - | CSPR_PORT_SIZE_8 \ - | CSPR_MSEL_GPCM \ - | CSPR_V) -#define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024) -#define CONFIG_SYS_CSOR3 0x0 -/* QIXIS Timing parameters for IFC CS3 */ -#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ - FTIM0_GPCM_TEADC(0x0e) | \ - FTIM0_GPCM_TEAHC(0x0e)) -#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ - FTIM1_GPCM_TRAD(0x1f)) -#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ - FTIM2_GPCM_TCH(0x8) | \ - FTIM2_GPCM_TWP(0x1f)) -#define CONFIG_SYS_CS3_FTIM3 0x0 - -/* NAND Flash on IFC */ -#define CONFIG_NAND_FSL_IFC -#define CONFIG_SYS_NAND_MAX_ECCPOS 256 -#define CONFIG_SYS_NAND_MAX_OOBFREE 2 -#define CONFIG_SYS_NAND_BASE 0xff800000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) -#else -#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE -#endif - -#define CONFIG_SYS_NAND_CSPR_EXT (0xf) -#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ - | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ - | CSPR_MSEL_NAND /* MSEL = NAND */ \ - | CSPR_V) -#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) - -#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ - | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ - | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ - | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ - | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ - | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ - | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ - -#define CONFIG_SYS_NAND_ONFI_DETECTION - -/* ONFI NAND Flash mode0 Timing Params */ -#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ - FTIM0_NAND_TWP(0x18) | \ - FTIM0_NAND_TWCHT(0x07) | \ - FTIM0_NAND_TWH(0x0a)) -#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ - FTIM1_NAND_TWBE(0x39) | \ - FTIM1_NAND_TRR(0x0e) | \ - FTIM1_NAND_TRP(0x18)) -#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ - FTIM2_NAND_TREH(0x0a) | \ - FTIM2_NAND_TWHRE(0x1e)) -#define CONFIG_SYS_NAND_FTIM3 0x0 - -#define CONFIG_SYS_NAND_DDR_LAW 11 - -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } -#define CONFIG_SYS_MAX_NAND_DEVICE 1 - -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) - -#if defined(CONFIG_MTD_RAW_NAND) -#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT -#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR -#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK -#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR -#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 -#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 -#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 -#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 -#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT -#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR -#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 -#else -#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT -#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR -#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 -#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT -#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR -#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK -#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR -#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 -#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 -#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 -#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 -#endif -#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT -#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR -#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 - -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE -#else -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#endif - -#if defined(CONFIG_RAMBOOT_PBL) -#define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_HWCONFIG - -/* define to use L1 as initial stack */ -#define CONFIG_L1_INIT_RAM -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 -/* The assembler doesn't like typecast */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ - ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ - CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) -#else -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe03c000 /* Initial L1 address */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS -#endif -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) -#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) - -/* Serial Port - controlled on board with jumper J8 - * open - index 2 - * shorted - index 1 - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) -#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) -#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ -#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 - -/* - * RTC configuration - */ -#define RTC -#define CONFIG_RTC_DS3231 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* - * RapidIO - */ -#ifdef CONFIG_SYS_SRIO -#ifdef CONFIG_SRIO1 -#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull -#else -#define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 -#endif -#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ -#endif - -#ifdef CONFIG_SRIO2 -#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull -#else -#define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 -#endif -#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ -#endif -#endif - -/* - * for slave u-boot IMAGE instored in master memory space, - * PHYS must be aligned based on the SIZE - */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull -/* - * for slave UCODE and ENV instored in master memory space, - * PHYS must be aligned based on the SIZE - */ -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ - -/* slave core release by master*/ -#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 -#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ - -/* - * SRIO_PCIE_BOOT - SLAVE - */ -#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE -#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 -#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ - (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) -#endif - -/* - * eSPI - Enhanced SPI - */ - -/* - * MAPLE - */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_MAPLE_MEM_PHYS 0xFA0000000ull -#else -#define CONFIG_SYS_MAPLE_MEM_PHYS 0xA0000000 -#endif - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ - -/* controller 1, direct to uli, tgtid 3, Base address 20000 */ -#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull -#else -#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 -#endif -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull -#else -#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 -#endif -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ - -/* Qman/Bman */ -#ifndef CONFIG_NOBQFMAN -#define CONFIG_SYS_BMAN_NUM_PORTALS 25 -#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull -#else -#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE -#endif -#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 -#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 -#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 -#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE -#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ - CONFIG_SYS_BMAN_CENA_SIZE) -#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 -#define CONFIG_SYS_QMAN_NUM_PORTALS 25 -#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull -#else -#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE -#endif -#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 -#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 -#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 -#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE -#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ - CONFIG_SYS_QMAN_CENA_SIZE) -#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 - -#define CONFIG_SYS_DPAA_FMAN - -#define CONFIG_SYS_DPAA_RMAN - -/* Default address of microcode for the Linux Fman driver */ -#if defined(CONFIG_SPIFLASH) -/* - * env is stored at 0x100000, sector size is 0x10000, ucode is stored after - * env, so we got 0x110000. - */ -#define CONFIG_SYS_FMAN_FW_ADDR 0x110000 -#elif defined(CONFIG_SDCARD) -/* - * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is - * about 545KB (1089 blocks), Env is stored after the image, and the env size is - * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. - */ -#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1130) -#elif defined(CONFIG_MTD_RAW_NAND) -#define CONFIG_SYS_FMAN_FW_ADDR (13 * CONFIG_SYS_NAND_BLOCK_SIZE) -#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) -/* - * Slave has no ucode locally, it can fetch this from remote. When implementing - * in two corenet boards, slave's ucode could be stored in master's memory - * space, the address can be mapped from slave TLB->slave LAW-> - * slave SRIO or PCIE outbound window->master inbound window-> - * master LAW->the ucode address in master's memory space. - */ -#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 -#else -#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 -#endif -#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 -#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) -#endif /* CONFIG_NOBQFMAN */ - -#ifdef CONFIG_SYS_DPAA_FMAN -#define SGMII_CARD_PORT1_PHY_ADDR 0x1C -#define SGMII_CARD_PORT2_PHY_ADDR 0x10 -#define SGMII_CARD_PORT3_PHY_ADDR 0x1E -#define SGMII_CARD_PORT4_PHY_ADDR 0x11 -#endif - -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#endif /* CONFIG_PCI */ - -#ifdef CONFIG_FMAN_ENET -#define CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR 0x10 -#define CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR 0x11 - -/*B4860 QDS AMC2PEX-2S default PHY_ADDR */ -#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0x7 /*SLOT 1*/ -#define CONFIG_SYS_FM1_10GEC2_PHY_ADDR 0x6 /*SLOT 2*/ - -#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c -#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d -#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e -#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f - -#define CONFIG_ETHPRIME "FM1@DTSEC1" -#endif - -#define CONFIG_SYS_FSL_B4860QDS_XFI_ERR - -/* - * Environment - */ -#define CONFIG_LOADS_ECHO /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ - -/* -* USB -*/ -#define CONFIG_HAS_FSL_DR_USB - -#ifdef CONFIG_HAS_FSL_DR_USB -#ifdef CONFIG_USB_EHCI_HCD -#define CONFIG_USB_EHCI_FSL -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#endif -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#ifdef CONFIG_CMD_KGDB -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ROOTPATH "/opt/nfsroot" -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ - -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 1000000 - -#define __USB_PHY_TYPE ulpi - -#ifdef CONFIG_ARCH_B4860 -#define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null," \ - "bank_intlv=cs0_cs1;" \ - "en_cpc:cpc2;" -#else -#define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;" -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - HWCONFIG \ - "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ - "netdev=eth0\0" \ - "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ - "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ - "tftpflash=tftpboot $loadaddr $uboot && " \ - "protect off $ubootaddr +$filesize && " \ - "erase $ubootaddr +$filesize && " \ - "cp.b $loadaddr $ubootaddr $filesize && " \ - "protect on $ubootaddr +$filesize && " \ - "cmp.b $loadaddr $ubootaddr $filesize\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=2000000\0" \ - "ramdiskfile=b4860qds/ramdisk.uboot\0" \ - "fdtaddr=1e00000\0" \ - "fdtfile=b4860qds/b4860qds.dtb\0" \ - "bdev=sda3\0" - -/* For emulation this causes u-boot to jump to the start of the proof point - app code automatically */ -#define CONFIG_PROOF_POINTS \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "cpu 1 release 0x29000000 - - -;" \ - "cpu 2 release 0x29000000 - - -;" \ - "cpu 3 release 0x29000000 - - -;" \ - "cpu 4 release 0x29000000 - - -;" \ - "cpu 5 release 0x29000000 - - -;" \ - "cpu 6 release 0x29000000 - - -;" \ - "cpu 7 release 0x29000000 - - -;" \ - "go 0x29000000" - -#define CONFIG_HVBOOT \ - "setenv bootargs config-addr=0x60000000; " \ - "bootm 0x01000000 - 0x00f00000" - -#define CONFIG_ALU \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "cpu 1 release 0x01000000 - - -;" \ - "cpu 2 release 0x01000000 - - -;" \ - "cpu 3 release 0x01000000 - - -;" \ - "cpu 4 release 0x01000000 - - -;" \ - "cpu 5 release 0x01000000 - - -;" \ - "cpu 6 release 0x01000000 - - -;" \ - "cpu 7 release 0x01000000 - - -;" \ - "go 0x01000000" - -#define CONFIG_LINUX \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "setenv ramdiskaddr 0x02000000;" \ - "setenv fdtaddr 0x01e00000;" \ - "setenv loadaddr 0x1000000;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_HDBOOT \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_LINUX - -#include - -#endif /* __CONFIG_H */ -- 2.39.5