From 7b5b9343139f934f1ce876e9466c065f20c8265c Mon Sep 17 00:00:00 2001 From: Anatolij Gustschin Date: Tue, 7 Jan 2020 16:37:42 +0100 Subject: [PATCH] imx: add imx8x capricorn giedi board Add support for i.MX8X based Capricorn Giedi SoM. Supported interfaces: GPIO, ENET, eMMC, I2C, UART. Console output: U-Boot SPL 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) Trying to boot from MMC1 Load image from MMC/SD 0x3e400 U-Boot 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) ##v01.07 CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C Model: Siemens Giedi Board: Capricorn Boot: MMC0 DRAM: 1022 MiB MMC: FSL_SDHC: 0 Loading Environment from MMC... OK In: serial@5a080000 Out: serial@5a080000 Err: serial@5a080000 Net: eth1: ethernet@5b050000 [PRIME] Autobooting in 1 seconds, press "" to stop Signed-off-by: Anatolij Gustschin --- arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx8-giedi.dts | 10 + arch/arm/dts/imx8qxp-capricorn-u-boot.dtsi | 133 ++++++ arch/arm/dts/imx8qxp-capricorn.dtsi | 285 +++++++++++++ arch/arm/mach-imx/imx8/Kconfig | 6 + board/siemens/capricorn/Kconfig | 12 + board/siemens/capricorn/MAINTAINERS | 9 + board/siemens/capricorn/Makefile | 12 + board/siemens/capricorn/board.c | 448 ++++++++++++++++++++ board/siemens/capricorn/imximage.cfg | 22 + board/siemens/capricorn/spl.c | 47 ++ board/siemens/capricorn/uboot-container.cfg | 13 + board/siemens/common/factoryset.c | 2 + configs/giedi_defconfig | 103 +++++ include/configs/capricorn-common.h | 185 ++++++++ include/configs/giedi.h | 19 + include/configs/siemens-ccp-common.h | 19 + include/configs/siemens-env-common.h | 201 +++++++++ 18 files changed, 1528 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/imx8-giedi.dts create mode 100644 arch/arm/dts/imx8qxp-capricorn-u-boot.dtsi create mode 100644 arch/arm/dts/imx8qxp-capricorn.dtsi create mode 100644 board/siemens/capricorn/Kconfig create mode 100644 board/siemens/capricorn/MAINTAINERS create mode 100644 board/siemens/capricorn/Makefile create mode 100644 board/siemens/capricorn/board.c create mode 100644 board/siemens/capricorn/imximage.cfg create mode 100644 board/siemens/capricorn/spl.c create mode 100644 board/siemens/capricorn/uboot-container.cfg create mode 100644 configs/giedi_defconfig create mode 100644 include/configs/capricorn-common.h create mode 100644 include/configs/giedi.h create mode 100644 include/configs/siemens-ccp-common.h create mode 100644 include/configs/siemens-env-common.h diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 983e235f44..f5169e173a 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -699,7 +699,8 @@ dtb-$(CONFIG_ARCH_IMX8) += \ imx8qm-rom7720-a1.dtb \ fsl-imx8qxp-ai_ml.dtb \ fsl-imx8qxp-colibri.dtb \ - fsl-imx8qxp-mek.dtb + fsl-imx8qxp-mek.dtb \ + imx8-giedi.dtb dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mm-evk.dtb \ diff --git a/arch/arm/dts/imx8-giedi.dts b/arch/arm/dts/imx8-giedi.dts new file mode 100644 index 0000000000..0dbfef2ee9 --- /dev/null +++ b/arch/arm/dts/imx8-giedi.dts @@ -0,0 +1,10 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019 Siemens AG + */ + +#include "imx8qxp-capricorn.dtsi" + +/ { + model = "Siemens Giedi"; +}; diff --git a/arch/arm/dts/imx8qxp-capricorn-u-boot.dtsi b/arch/arm/dts/imx8qxp-capricorn-u-boot.dtsi new file mode 100644 index 0000000000..1cf58fc3f9 --- /dev/null +++ b/arch/arm/dts/imx8qxp-capricorn-u-boot.dtsi @@ -0,0 +1,133 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019 Siemens AG + */ + +&{/imx8qx-pm} { + + u-boot,dm-spl; +}; + +&mu { + u-boot,dm-spl; +}; + +&clk { + u-boot,dm-spl; +}; + +&iomuxc { + u-boot,dm-spl; +}; + +&pd_lsio { + u-boot,dm-spl; +}; + +&pd_lsio_gpio0 { + u-boot,dm-spl; +}; + +&pd_lsio_gpio1 { + u-boot,dm-spl; +}; + +&pd_lsio_gpio2 { + u-boot,dm-spl; +}; + +&pd_lsio_gpio3 { + u-boot,dm-spl; +}; + +&pd_lsio_gpio4 { + u-boot,dm-spl; +}; + +&pd_lsio_gpio5 { + u-boot,dm-spl; +}; + +&pd_lsio_gpio6 { + u-boot,dm-spl; +}; + +&pd_lsio_gpio7 { + u-boot,dm-spl; +}; + +&pd_dma { + u-boot,dm-spl; +}; + +&pd_dma_lpuart0 { + u-boot,dm-spl; +}; + +&pd_dma_lpuart2 { + u-boot,dm-spl; +}; + +&pd_conn { + u-boot,dm-spl; +}; + +&pd_conn_sdch0 { + u-boot,dm-spl; +}; + +&pd_conn_sdch1 { + u-boot,dm-spl; +}; + +&pd_conn_sdch2 { + u-boot,dm-spl; +}; + +&gpio0 { + u-boot,dm-spl; +}; + +&gpio1 { + u-boot,dm-spl; +}; + +&gpio2 { + u-boot,dm-spl; +}; + +&gpio3 { + u-boot,dm-spl; +}; + +&gpio4 { + u-boot,dm-spl; +}; + +&gpio5 { + u-boot,dm-spl; +}; + +&gpio6 { + u-boot,dm-spl; +}; + +&gpio7 { + u-boot,dm-spl; +}; + +&lpuart0 { + u-boot,dm-spl; +}; + +&lpuart2 { + u-boot,dm-spl; +}; + +&usdhc1 { + u-boot,dm-spl; +}; + +&usdhc2 { + u-boot,dm-spl; +}; diff --git a/arch/arm/dts/imx8qxp-capricorn.dtsi b/arch/arm/dts/imx8qxp-capricorn.dtsi new file mode 100644 index 0000000000..db5653ea1f --- /dev/null +++ b/arch/arm/dts/imx8qxp-capricorn.dtsi @@ -0,0 +1,285 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2017 NXP + * + * Copyright 2019 Siemens AG + * + */ + +/dts-v1/; + +#include "fsl-imx8qxp.dtsi" +#include "imx8qxp-capricorn-u-boot.dtsi" + +/ { + model = "Siemens Giedi"; + compatible = "siemens,capricorn", "fsl,imx8qxp"; + + chosen { + bootargs = "console=ttyLP2,115200 earlycon=lpuart32,0x5a080000,115200"; + stdout-path = &lpuart2; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + run { + label = "run"; + gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + flt { + label = "flt"; + gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + svc { + label = "svc"; + gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + com1_tx { + label = "com1-tx"; + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + com1_rx { + label = "com1-rx"; + gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + com2_tx { + label = "com2-tx"; + gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + com2_rx { + label = "com2-rx"; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + cloud { + label = "cloud"; + gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + wlan { + label = "wlan"; + gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + dbg1 { + label = "dbg1"; + gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + dbg2 { + label = "dbg2"; + gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + dbg3 { + label = "dbg3"; + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + dbg4 { + label = "dbg4"; + gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + + muxcgrp: imx8qxp-som { + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = < + SC_P_ESAI0_FST_LSIO_GPIO0_IO01 0x06000021 + SC_P_ESAI0_TX0_LSIO_GPIO0_IO04 0x06000021 + SC_P_SAI0_TXC_LSIO_GPIO0_IO26 0x06000021 + SC_P_SAI1_RXD_LSIO_GPIO0_IO29 0x06000021 + SC_P_FLEXCAN1_RX_LSIO_GPIO1_IO17 0x06000021 + SC_P_FLEXCAN1_TX_LSIO_GPIO1_IO18 0x06000021 + SC_P_QSPI0B_SCLK_LSIO_GPIO3_IO17 0x06000021 + SC_P_QSPI0B_DATA0_LSIO_GPIO3_IO18 0x06000021 + SC_P_QSPI0B_DATA1_LSIO_GPIO3_IO19 0x06000021 + SC_P_USB_SS3_TC0_LSIO_GPIO4_IO03 0x06000021 + SC_P_ENET0_RGMII_TXD1_LSIO_GPIO5_IO00 0x06000021 + SC_P_ENET0_RGMII_TXD2_LSIO_GPIO5_IO01 0x06000021 + SC_P_ENET0_REFCLK_125M_25M_LSIO_GPIO5_IO09 0x06000021 + >; + }; + + pinctrl_lpi2c0: lpi2c0grp { + fsl,pins = < + SC_P_MIPI_CSI0_GPIO0_00_ADMA_I2C0_SCL 0x0C000020 + SC_P_MIPI_CSI0_GPIO0_01_ADMA_I2C0_SDA 0x0C000020 + >; + }; + + pinctrl_lpi2c1: lpi2c1grp { + fsl,pins = < + SC_P_MIPI_DSI0_GPIO0_00_ADMA_I2C1_SCL 0x0C000020 + SC_P_MIPI_DSI0_GPIO0_01_ADMA_I2C1_SDA 0x0C000020 + >; + }; + + pinctrl_lpuart2: lpuart2grp { + fsl,pins = < + SC_P_UART2_RX_ADMA_UART2_RX 0x06000020 + SC_P_UART2_TX_ADMA_UART2_TX 0x06000020 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + SC_P_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041 + SC_P_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021 + SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021 + SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021 + SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021 + SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021 + SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021 + SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021 + SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021 + SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021 + SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE 0x06000041 + SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B 0x00000021 + SC_P_ENET0_RGMII_TXC_LSIO_GPIO4_IO29 0x06000021 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + SC_P_ENET0_RGMII_RXC_CONN_USDHC1_CLK 0x06000041 + SC_P_ENET0_RGMII_RX_CTL_CONN_USDHC1_CMD 0x00000021 + SC_P_ENET0_RGMII_RXD0_CONN_USDHC1_DATA0 0x00000021 + SC_P_ENET0_RGMII_RXD1_CONN_USDHC1_DATA1 0x00000021 + SC_P_ENET0_RGMII_RXD2_CONN_USDHC1_DATA2 0x00000021 + SC_P_ENET0_RGMII_RXD3_CONN_USDHC1_DATA3 0x00000021 + SC_P_ENET0_RGMII_TXD2_CONN_USDHC1_CD_B 0x06000021 + //SC_P_ENET0_RGMII_TXD2_LSIO_GPIO5_IO01 0x06000021 + SC_P_ENET0_RGMII_TX_CTL_LSIO_GPIO4_IO30 0x06000021 + >; + }; + + pinctrl_fec2: fec2grp { + fsl,pins = < + SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB0_PAD 0x000014a0 + SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB1_PAD 0x000014a0 + SC_P_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD 0x000514a0 + + SC_P_ENET0_MDC_CONN_ENET1_MDC 0x00000060 + SC_P_ENET0_MDIO_CONN_ENET1_MDIO 0x00000060 + + SC_P_ESAI0_FSR_CONN_ENET1_RCLK50M_IN 0x00000060 + SC_P_SPDIF0_RX_CONN_ENET1_RGMII_RXD0 0x00000060 + SC_P_ESAI0_TX3_RX2_CONN_ENET1_RGMII_RXD1 0x00000060 + SC_P_ESAI0_TX2_RX3_CONN_ENET1_RMII_RX_ER 0x00000060 + SC_P_SPDIF0_TX_CONN_ENET1_RGMII_RX_CTL 0x00000060 + SC_P_ESAI0_TX4_RX1_CONN_ENET1_RGMII_TXD0 0x00000060 + SC_P_ESAI0_TX5_RX0_CONN_ENET1_RGMII_TXD1 0x00000060 + SC_P_ESAI0_SCKR_CONN_ENET1_RGMII_TX_CTL 0x00000060 /* ERST: Reset pin */ + >; + }; + }; +}; + +&i2c0 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpi2c0>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpi2c1>; + status = "okay"; +}; + +&lpuart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart2>; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + clock-frequency=<52000000>; + no-1-8-v; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&gpio3 { + status = "okay"; +}; + +&gpio4 { + status = "okay"; +}; + +&gpio5 { + status = "okay"; +}; + +&fec1 { + status ="disabled"; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec2>; + phy-mode = "rmii"; + + phy-handle = <ðphy1>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + ethphy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + }; +}; diff --git a/arch/arm/mach-imx/imx8/Kconfig b/arch/arm/mach-imx/imx8/Kconfig index cdb78afacf..bb45c8e3e6 100644 --- a/arch/arm/mach-imx/imx8/Kconfig +++ b/arch/arm/mach-imx/imx8/Kconfig @@ -55,6 +55,11 @@ config TARGET_COLIBRI_IMX8X select BOARD_LATE_INIT select IMX8QXP +config TARGET_GIEDI + bool "Support i.MX8QXP Capricorn Giedi board" + select BOARD_LATE_INIT + select IMX8QXP + config TARGET_IMX8QM_MEK bool "Support i.MX8QM MEK board" select BOARD_LATE_INIT @@ -78,5 +83,6 @@ source "board/freescale/imx8qxp_mek/Kconfig" source "board/advantech/imx8qm_rom7720_a1/Kconfig" source "board/toradex/apalis-imx8/Kconfig" source "board/toradex/colibri-imx8x/Kconfig" +source "board/siemens/capricorn/Kconfig" endif diff --git a/board/siemens/capricorn/Kconfig b/board/siemens/capricorn/Kconfig new file mode 100644 index 0000000000..ed1f793e40 --- /dev/null +++ b/board/siemens/capricorn/Kconfig @@ -0,0 +1,12 @@ +if TARGET_GIEDI + +config SYS_BOARD + default "capricorn" + +config SYS_VENDOR + default "siemens" + +config SYS_CONFIG_NAME + default "giedi" + +endif diff --git a/board/siemens/capricorn/MAINTAINERS b/board/siemens/capricorn/MAINTAINERS new file mode 100644 index 0000000000..5d81aaf149 --- /dev/null +++ b/board/siemens/capricorn/MAINTAINERS @@ -0,0 +1,9 @@ +CAPRICORN BOARD +M: Anatolij Gustschin +S: Maintained +F: board/siemens/capricorn/ +F: include/configs/capricorn-common.h +F: include/configs/giedi.h +F: include/configs/siemens-ccp-common.h +F: include/configs/siemens-env-common.h +F: configs/giedi_defconfig diff --git a/board/siemens/capricorn/Makefile b/board/siemens/capricorn/Makefile new file mode 100644 index 0000000000..d5846cc8e3 --- /dev/null +++ b/board/siemens/capricorn/Makefile @@ -0,0 +1,12 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright 2019 Siemens AG +# + +obj-y += board.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +else +obj-y += ../common/factoryset.o +endif diff --git a/board/siemens/capricorn/board.c b/board/siemens/capricorn/board.c new file mode 100644 index 0000000000..00fd4b9658 --- /dev/null +++ b/board/siemens/capricorn/board.c @@ -0,0 +1,448 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2017-2019 NXP + * + * Copyright 2019 Siemens AG + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#ifndef CONFIG_SPL +#include +#endif +#include "../common/factoryset.h" + +#define GPIO_PAD_CTRL \ + ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define ENET_NORMAL_PAD_CTRL \ + ((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +#define UART_PAD_CTRL \ + ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +static iomux_cfg_t uart2_pads[] = { + SC_P_UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL), + SC_P_UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx8_iomux_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); +} + +int board_early_init_f(void) +{ + /* Set UART clock root to 80 MHz */ + sc_pm_clock_rate_t rate = SC_80MHZ; + int ret; + + ret = sc_pm_setup_uart(SC_R_UART_0, rate); + ret |= sc_pm_setup_uart(SC_R_UART_2, rate); + if (ret) + return ret; + + setup_iomux_uart(); + + return 0; +} + +#define ENET_PHY_RESET IMX_GPIO_NR(0, 3) +#define ENET_TEST_1 IMX_GPIO_NR(0, 8) +#define ENET_TEST_2 IMX_GPIO_NR(0, 9) + +/*#define ETH_IO_TEST*/ +static iomux_cfg_t enet_reset[] = { + SC_P_ESAI0_SCKT | MUX_MODE_ALT(4) | MUX_PAD_CTRL(GPIO_PAD_CTRL), +#ifdef ETH_IO_TEST + /* GPIO0.IO08 MODE3: TXD0 */ + SC_P_ESAI0_TX4_RX1 | MUX_MODE_ALT(4) | + MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), + /* GPIO0.IO09 MODE3: TXD1 */ + SC_P_ESAI0_TX5_RX0 | MUX_MODE_ALT(4) | + MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL), +#endif +}; + +static void enet_device_phy_reset(void) +{ + int ret = 0; + + imx8_iomux_setup_multiple_pads(enet_reset, ARRAY_SIZE(enet_reset)); + + ret = gpio_request(ENET_PHY_RESET, "enet_phy_reset"); + if (!ret) { + gpio_direction_output(ENET_PHY_RESET, 1); + gpio_set_value(ENET_PHY_RESET, 0); + /* SMSC9303 TRM chapter 14.5.2 */ + udelay(200); + gpio_set_value(ENET_PHY_RESET, 1); + } else { + printf("ENET RESET failed!\n"); + } + +#ifdef ETH_IO_TEST + ret = gpio_request(ENET_TEST_1, "enet_test1"); + if (!ret) { + int i; + + printf("ENET TEST 1!\n"); + for (i = 0; i < 20; i++) { + gpio_direction_output(ENET_TEST_1, 1); + gpio_set_value(ENET_TEST_1, 0); + udelay(50); + gpio_set_value(ENET_TEST_1, 1); + udelay(50); + } + gpio_free(ENET_TEST_1); + } else { + printf("GPIO for ENET TEST 1 failed!\n"); + } + ret = gpio_request(ENET_TEST_2, "enet_test2"); + if (!ret) { + int i; + + printf("ENET TEST 2!\n"); + for (i = 0; i < 20; i++) { + gpio_direction_output(ENET_TEST_2, 1); + gpio_set_value(ENET_TEST_2, 0); + udelay(50); + gpio_set_value(ENET_TEST_2, 1); + udelay(50); + } + gpio_free(ENET_TEST_2); + } else { + printf("GPIO for ENET TEST 2 failed!\n"); + } +#endif +} + +int setup_gpr_fec(void) +{ + sc_ipc_t ipc_handle = -1; + sc_err_t err = 0; + unsigned int test; + + /* + * TX_CLK_SEL: it controls a mux between clock coming from the pad 50M + * input pin and clock generated internally to connectivity subsystem + * 0: internal clock + * 1: external clock ---> your choice for RMII + * + * CLKDIV_SEL: it controls a div by 2 on the internal clock path à + * it should be don’t care when using external clock + * 0: non-divided clock + * 1: clock divided by 2 + * 50_DISABLE or 125_DISABLE: + * it’s used to disable the clock tree going outside the chip + * when reference clock is generated internally. + * It should be don’t care when reference clock is provided + * externally. + * 0: clock is enabled + * 1: clock is disabled + * + * SC_C_TXCLK = 24, + * SC_C_CLKDIV = 25, + * SC_C_DISABLE_50 = 26, + * SC_C_DISABLE_125 = 27, + */ + + err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, 1); + if (err != SC_ERR_NONE) + printf("Error in setting up SC_C %d\n\r", SC_C_TXCLK); + + sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, &test); + debug("TEST SC_C %d-->%d\n\r", SC_C_TXCLK, test); + + err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_CLKDIV, 0); + if (err != SC_ERR_NONE) + printf("Error in setting up SC_C %d\n\r", SC_C_CLKDIV); + + sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_CLKDIV, &test); + debug("TEST SC_C %d-->%d\n\r", SC_C_CLKDIV, test); + + err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_DISABLE_50, 0); + if (err != SC_ERR_NONE) + printf("Error in setting up SC_C %d\n\r", SC_C_DISABLE_50); + + sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, &test); + debug("TEST SC_C %d-->%d\n\r", SC_C_DISABLE_50, test); + + err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_DISABLE_125, 1); + if (err != SC_ERR_NONE) + printf("Error in setting up SC_C %d\n\r", SC_C_DISABLE_125); + + sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_TXCLK, &test); + debug("TEST SC_C %d-->%d\n\r", SC_C_DISABLE_125, test); + + err = sc_misc_set_control(ipc_handle, SC_R_ENET_1, SC_C_SEL_125, 1); + if (err != SC_ERR_NONE) + printf("Error in setting up SC_C %d\n\r", SC_C_SEL_125); + + sc_misc_get_control(ipc_handle, SC_R_ENET_1, SC_C_SEL_125, &test); + debug("TEST SC_C %d-->%d\n\r", SC_C_SEL_125, test); + + return 0; +} + +#if IS_ENABLED(CONFIG_FEC_MXC) +#include +int board_phy_config(struct phy_device *phydev) +{ + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} + +#endif + +static int setup_fec(void) +{ + setup_gpr_fec(); + /* Reset ENET PHY */ + enet_device_phy_reset(); + return 0; +} + +void reset_cpu(ulong addr) +{ +} + +#ifndef CONFIG_SPL_BUILD +/* LED's */ +static int board_led_init(void) +{ + struct udevice *bus, *dev; + u8 pca_led[2] = { 0x00, 0x00 }; + int ret; + + /* init all GPIO LED's */ + if (IS_ENABLED(CONFIG_LED)) + led_default_state(); + + /* enable all leds on PCA9552 */ + ret = uclass_get_device_by_seq(UCLASS_I2C, PCA9552_1_I2C_BUS, &bus); + if (ret) { + printf("ERROR: I2C get %d\n", ret); + return ret; + } + + ret = dm_i2c_probe(bus, PCA9552_1_I2C_ADDR, 0, &dev); + if (ret) { + printf("ERROR: PCA9552 probe failed\n"); + return ret; + } + + ret = dm_i2c_write(dev, 0x16, pca_led, sizeof(pca_led)); + if (ret) { + printf("ERROR: PCA9552 write failed\n"); + return ret; + } + + mdelay(1); + return ret; +} +#endif /* !CONFIG_SPL_BUILD */ + +int checkboard(void) +{ + puts("Board: Capricorn\n"); + + /* + * Running build_info() doesn't work with current SCFW blob. + * Uncomment below call when new blob is available. + */ + /*build_info();*/ + + print_bootinfo(); + return 0; +} + +int board_init(void) +{ + setup_fec(); + return 0; +} + +#ifdef CONFIG_OF_BOARD_SETUP +int ft_board_setup(void *blob, bd_t *bd) +{ + return 0; +} +#endif + +int board_mmc_get_env_dev(int devno) +{ + return devno; +} + +static int check_mmc_autodetect(void) +{ + char *autodetect_str = env_get("mmcautodetect"); + + if (autodetect_str && (strcmp(autodetect_str, "yes") == 0)) + return 1; + + return 0; +} + +/* This should be defined for each board */ +__weak int mmc_map_to_kernel_blk(int dev_no) +{ + return dev_no; +} + +void board_late_mmc_env_init(void) +{ + char cmd[32]; + char mmcblk[32]; + u32 dev_no = mmc_get_env_dev(); + + if (!check_mmc_autodetect()) + return; + + env_set_ulong("mmcdev", dev_no); + + /* Set mmcblk env */ + sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw", + mmc_map_to_kernel_blk(dev_no)); + env_set("mmcroot", mmcblk); + + sprintf(cmd, "mmc dev %d", dev_no); + run_command(cmd, 0); +} + +#ifndef CONFIG_SPL_BUILD +int factoryset_read_eeprom(int i2c_addr); + +static int load_parameters_from_factoryset(void) +{ + int ret; + + ret = factoryset_read_eeprom(EEPROM_I2C_ADDR); + if (ret) + return ret; + + return factoryset_env_set(); +} + +int board_late_init(void) +{ + env_set("sec_boot", "no"); +#ifdef CONFIG_AHAB_BOOT + env_set("sec_boot", "yes"); +#endif + +#ifdef CONFIG_ENV_IS_IN_MMC + board_late_mmc_env_init(); +#endif + /* Init LEDs */ + if (board_led_init()) + printf("I2C LED init failed\n"); + + /* Set environment from factoryset */ + if (load_parameters_from_factoryset()) + printf("Loading factoryset parameters failed!\n"); + + return 0; +} + +/* Service button */ +#define MAX_PIN_NUMBER 128 +#define BOARD_DEFAULT_BUTTON_GPIO IMX_GPIO_NR(1, 31) + +unsigned char get_button_state(char * const envname, unsigned char def) +{ + int button = 0; + int gpio; + char *ptr_env; + + /* If button is not found we take default */ + ptr_env = env_get(envname); + if (!ptr_env) { + printf("Using default: %u\n", def); + gpio = def; + } else { + gpio = (unsigned char)simple_strtoul(ptr_env, NULL, 0); + if (gpio > MAX_PIN_NUMBER) + gpio = def; + } + + gpio_request(gpio, ""); + gpio_direction_input(gpio); + if (gpio_get_value(gpio)) + button = 1; + else + button = 0; + + gpio_free(gpio); + + return button; +} + +/* + * This command returns the status of the user button on + * Input - none + * Returns - 1 if button is held down + * 0 if button is not held down + */ +static int +do_userbutton(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + int button = 0; + + button = get_button_state("button_usr1", BOARD_DEFAULT_BUTTON_GPIO); + + if (argc > 1) + printf("Button state: %u\n", button); + + return button; +} + +U_BOOT_CMD( + usrbutton, CONFIG_SYS_MAXARGS, 2, do_userbutton, + "Return the status of user button", + "[print]" +); + +#define ERST IMX_GPIO_NR(0, 3) + +static int +do_eth_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + gpio_request(ERST, "ERST"); + gpio_direction_output(ERST, 0); + udelay(200); + gpio_set_value(ERST, 1); + return 0; +} + +U_BOOT_CMD( + switch_rst, CONFIG_SYS_MAXARGS, 2, do_eth_reset, + "Reset eth phy", + "[print]" +); +#endif /* ! CONFIG_SPL_BUILD */ diff --git a/board/siemens/capricorn/imximage.cfg b/board/siemens/capricorn/imximage.cfg new file mode 100644 index 0000000000..8660e50cbd --- /dev/null +++ b/board/siemens/capricorn/imximage.cfg @@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018 NXP + * + * Refer doc/README.imx8image for more details about how-to configure + * and create imx8image boot image + */ + +#define __ASSEMBLY__ + +/* Boot from SD, sector size 0x400 */ +BOOT_FROM SD 0x400 +/* SoC type IMX8QX */ +SOC_TYPE IMX8QX +/* Append seco container image */ +APPEND ahab-container.img +/* Create the 2nd container */ +CONTAINER +/* Add scfw image with exec attribute */ +IMAGE SCU capricorn-scfw-tcm.bin +/* Add ATF image with exec attribute */ +IMAGE A35 spl/u-boot-spl.bin 0x00100000 diff --git a/board/siemens/capricorn/spl.c b/board/siemens/capricorn/spl.c new file mode 100644 index 0000000000..47fe86ccc0 --- /dev/null +++ b/board/siemens/capricorn/spl.c @@ -0,0 +1,47 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 NXP + * + * Copyright 2019 Siemens AG + * + */ +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +void spl_board_init(void) +{ + struct udevice *dev; + + uclass_find_first_device(UCLASS_MISC, &dev); + + for (; dev; uclass_find_next_device(&dev)) { + if (device_probe(dev)) + continue; + } + + arch_cpu_init(); + + board_early_init_f(); + + timer_init(); + + preloader_console_init(); +} + +void board_init_f(ulong dummy) +{ + /* Clear global data */ + memset((void *)gd, 0, sizeof(gd_t)); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + board_init_r(NULL, 0); +} diff --git a/board/siemens/capricorn/uboot-container.cfg b/board/siemens/capricorn/uboot-container.cfg new file mode 100644 index 0000000000..8165811818 --- /dev/null +++ b/board/siemens/capricorn/uboot-container.cfg @@ -0,0 +1,13 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2019 NXP + */ + +#define __ASSEMBLY__ + +/* This file is to create a container image could be loaded by SPL */ +BOOT_FROM SD 0x400 +SOC_TYPE IMX8QX +CONTAINER +IMAGE A35 bl31.bin 0x80000000 +IMAGE A35 u-boot.bin CONFIG_SYS_TEXT_BASE diff --git a/board/siemens/common/factoryset.c b/board/siemens/common/factoryset.c index 7715ddf307..0d3701c03c 100644 --- a/board/siemens/common/factoryset.c +++ b/board/siemens/common/factoryset.c @@ -13,7 +13,9 @@ #include #include #include +#if !CONFIG_IS_ENABLED(TARGET_GIEDI) && !CONFIG_IS_ENABLED(TARGET_DENEB) #include +#endif #include #include #include diff --git a/configs/giedi_defconfig b/configs/giedi_defconfig new file mode 100644 index 0000000000..6b54cc8af4 --- /dev/null +++ b/configs/giedi_defconfig @@ -0,0 +1,103 @@ +CONFIG_ARM=y +CONFIG_SPL_SYS_ICACHE_OFF=y +CONFIG_SPL_SYS_DCACHE_OFF=y +CONFIG_ARCH_IMX8=y +CONFIG_SYS_TEXT_BASE=0x80020000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SYS_MALLOC_F_LEN=0x4000 +CONFIG_SPL_LOAD_IMX_CONTAINER=y +CONFIG_IMX_CONTAINER_CFG="board/siemens/capricorn/uboot-container.cfg" +CONFIG_TARGET_GIEDI=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_OFFSET=0x0 +CONFIG_NR_DRAM_BANKS=3 +CONFIG_SPL=y +CONFIG_SPL_TEXT_BASE=0x100000 +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_SYSTEM_SETUP=y +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/siemens/capricorn/imximage.cfg" +CONFIG_BOOTDELAY=3 +CONFIG_LOG=y +CONFIG_SPL_BOARD_INIT=y +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_SEPARATE_BSS=y +CONFIG_SPL_POWER_SUPPORT=y +CONFIG_SPL_POWER_DOMAIN=y +CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="U-Boot# " +CONFIG_AUTOBOOT_KEYED=y +CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"\" to stop\n" +CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b" +CONFIG_AUTOBOOT_KEYED_CTRLC=y +CONFIG_CMD_CPU=y +# CONFIG_CMD_IMPORTENV is not set +CONFIG_CMD_CLK=y +CONFIG_CMD_DM=y +CONFIG_CMD_FUSE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="imx8-giedi" +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_ENV_OFFSET_REDUND=0x2000 +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_SPL_DM=y +CONFIG_SPL_CLK=y +CONFIG_CLK_IMX8=y +CONFIG_CPU=y +CONFIG_DM_GPIO=y +CONFIG_MXC_GPIO=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_IMX_LPI2C=y +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_MISC=y +CONFIG_DM_MMC=y +CONFIG_SUPPORT_EMMC_BOOT=y +CONFIG_MMC_IO_VOLTAGE=y +CONFIG_MMC_UHS_SUPPORT=y +CONFIG_MMC_HS400_SUPPORT=y +CONFIG_FSL_USDHC=y +CONFIG_PHYLIB=y +CONFIG_MV88E61XX_SWITCH=y +CONFIG_MV88E61XX_CPU_PORT=5 +CONFIG_MV88E61XX_PHY_PORTS=0x7 +CONFIG_MV88E61XX_FIXED_PORTS=0x0 +CONFIG_DM_ETH=y +CONFIG_FEC_MXC_SHARE_MDIO=y +CONFIG_FEC_MXC_MDIO_BASE=0x5B050000 +CONFIG_FEC_MXC=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_SPL_PINCTRL=y +CONFIG_PINCTRL_IMX8=y +CONFIG_POWER_DOMAIN=y +CONFIG_IMX8_POWER_DOMAIN=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_SPL_DM_REGULATOR_GPIO=y +CONFIG_DM_SERIAL=y +CONFIG_FSL_LPUART=y +CONFIG_DM_THERMAL=y +CONFIG_IMX_SCU_THERMAL=y +# CONFIG_SPL_WDT is not set +CONFIG_SPL_TINY_MEMSET=y +# CONFIG_EFI_LOADER is not set diff --git a/include/configs/capricorn-common.h b/include/configs/capricorn-common.h new file mode 100644 index 0000000000..254b3a5a76 --- /dev/null +++ b/include/configs/capricorn-common.h @@ -0,0 +1,185 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2017-2018 NXP + * Copyright 2019 Siemens AG + */ + +#ifndef __IMX8X_CAPRICORN_H +#define __IMX8X_CAPRICORN_H + +#include +#include + +#include "siemens-env-common.h" +#include "siemens-ccp-common.h" + +/* SPL config */ +#ifdef CONFIG_SPL_BUILD + +#define CONFIG_SPL_MAX_SIZE (124 * 1024) +#define CONFIG_SYS_MONITOR_LEN (1024 * 1024) +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x800 +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 0 + +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" +#define CONFIG_SPL_STACK 0x013E000 +#define CONFIG_SPL_BSS_START_ADDR 0x00128000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */ +#define CONFIG_SYS_SPL_MALLOC_START 0x00120000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* 12 KB */ +#define CONFIG_MALLOC_F_ADDR 0x00120000 + +#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE + +#endif /* CONFIG_SPL_BUILD */ + +#define CONFIG_FACTORYSET + +#undef CONFIG_IDENT_STRING +#define CONFIG_IDENT_STRING GENERATE_CCP_VERSION("01", "07") + +#define CONFIG_REMAKE_ELF + +#define CONFIG_BOARD_EARLY_INIT_F + +/* Commands */ +#define CONFIG_CMD_READ + +#undef CONFIG_CMD_EXPORTENV +#undef CONFIG_CMD_IMPORTENV +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_CRC32 +#undef CONFIG_BOOTM_NETBSD + +/* ENET Config */ +#define CONFIG_FEC_XCV_TYPE RMII +#define FEC_QUIRK_ENET_MAC + +/* ENET1 connects to base board and MUX with ESAI */ +#define CONFIG_FEC_ENET_DEV 1 +#define CONFIG_FEC_MXC_PHYADDR 0x0 +#define CONFIG_ETHPRIME "eth1" + +/* I2C Configuration */ +#ifndef CONFIG_SPL_BUILD +#define CONFIG_SYS_I2C_SPEED 400000 +/* EEPROM */ +#define EEPROM_I2C_BUS 0 /* I2C0 */ +#define EEPROM_I2C_ADDR 0x50 +/* PCA9552 */ +#define PCA9552_1_I2C_BUS 1 /* I2C1 */ +#define PCA9552_1_I2C_ADDR 0x60 +#endif /* !CONFIG_SPL_BUILD */ + +/* AHAB */ +#ifdef CONFIG_AHAB_BOOT +#define AHAB_ENV "sec_boot=yes\0" +#else +#define AHAB_ENV "sec_boot=no\0" +#endif + +#define MFG_ENV_SETTINGS_DEFAULT \ + "mfgtool_args=setenv bootargs console=${console},${baudrate} " \ + "rdinit=/linuxrc " \ + "clk_ignore_unused "\ + "\0" \ + "kboot=booti\0"\ + "bootcmd_mfg=run mfgtool_args;" \ + "if iminfo ${initrd_addr}; then " \ + "if test ${tee} = yes; then " \ + "bootm ${tee_addr} ${initrd_addr} ${fdt_addr}; " \ + "else " \ + "booti ${loadaddr} ${initrd_addr} ${fdt_addr}; " \ + "fi; " \ + "else " \ + "echo \"Run fastboot ...\"; fastboot 0; " \ + "fi;\0" + +/* Boot M4 */ +#define M4_BOOT_ENV \ + "m4_0_image=m4_0.bin\0" \ + "loadm4image_0=fatload mmc ${mmcdev}:${mmcpart} " \ + "${loadaddr} ${m4_0_image}\0" \ + "m4boot_0=run loadm4image_0; dcache flush; bootaux ${loadaddr} 0\0" \ + +#define CONFIG_MFG_ENV_SETTINGS \ + MFG_ENV_SETTINGS_DEFAULT \ + "initrd_addr=0x83100000\0" \ + "initrd_high=0xffffffffffffffff\0" \ + "emmc_dev=0\0" + +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_MFG_ENV_SETTINGS \ + M4_BOOT_ENV \ + AHAB_ENV \ + ENV_COMMON \ + "script=boot.scr\0" \ + "image=Image\0" \ + "panel=NULL\0" \ + "console=ttyLP2\0" \ + "fdt_addr=0x83000000\0" \ + "fdt_high=0xffffffffffffffff\0" \ + "cntr_addr=0x88000000\0" \ + "cntr_file=os_cntr_signed.bin\0" \ + "initrd_addr=0x83800000\0" \ + "initrd_high=0xffffffffffffffff\0" \ + "netdev=eth0\0" \ + "nfsopts=vers=3,udp,rsize=4096,wsize=4096,nolock rw\0" \ + "hostname=capricorn\0" \ + ENV_EMMC \ + ENV_NET + +#define CONFIG_BOOTCOMMAND \ + "if usrbutton; then " \ + "run flash_self_test; " \ + "reset; " \ + "fi;" \ + "run flash_self;" \ + "reset;" + +/* Default location for tftp and bootm */ +#define CONFIG_LOADADDR 0x80280000 +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000 + +#define CONFIG_BOOTCOUNT_LIMIT +#define CONFIG_BOOTCOUNT_ENV + +/* Environment organisation */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC1, eMMC */ +#define CONFIG_SYS_MMC_ENV_PART 2 /* 2nd boot partition */ + +/* On CCP board, USDHC1 is for eMMC */ +#define CONFIG_MMCROOT "/dev/mmcblk0p2" /* eMMC */ +#define CONFIG_SYS_MMC_IMG_LOAD_PART 1 + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 * 1024)) * 1024) + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define PHYS_SDRAM_1 0x80000000 +#define PHYS_SDRAM_2 0x880000000 +/* DDR3 board total DDR is 1 GB */ +#define PHYS_SDRAM_1_SIZE 0x40000000 /* 1 GB */ +#define PHYS_SDRAM_2_SIZE 0x00000000 /* 0 GB */ + +#define CONFIG_SYS_MEMTEST_START 0xA0000000 +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \ + (PHYS_SDRAM_1_SIZE >> 2)) + +/* Console buffer and boot args */ +#define CONFIG_SYS_CBSIZE 2048 +#define CONFIG_SYS_MAXARGS 64 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +/* Generic Timer Definitions */ +#define COUNTER_FREQUENCY 8000000 /* 8MHz */ + +#define BOOTAUX_RESERVED_MEM_BASE 0x88000000 +#define BOOTAUX_RESERVED_MEM_SIZE SZ_128M /* Reserve from second 128MB */ + +#endif /* __IMX8X_CAPRICORN_H */ diff --git a/include/configs/giedi.h b/include/configs/giedi.h new file mode 100644 index 0000000000..dabb1fb171 --- /dev/null +++ b/include/configs/giedi.h @@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2019 Siemens AG + * + */ + +#ifndef __GIEDI_H +#define __GIEDI_H + +#include "capricorn-common.h" + +#undef CONFIG_IDENT_STRING +#define CONFIG_IDENT_STRING GENERATE_CCP_VERSION("01", "07") + +/* DDR3 board total DDR is 1 GB */ +#undef PHYS_SDRAM_1_SIZE +#define PHYS_SDRAM_1_SIZE 0x40000000 /* 1 GB */ + +#endif /* __GIEDI_H */ diff --git a/include/configs/siemens-ccp-common.h b/include/configs/siemens-ccp-common.h new file mode 100644 index 0000000000..01051c8ad7 --- /dev/null +++ b/include/configs/siemens-ccp-common.h @@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* Be very careful updating CONFIG_IDENT_STRING + * This string will control the update flow whether an U-Boot should be + * updated or not. If the version of installed U-Boot (in flash) is smaller + * than the version to be installed (from update file), an update will + * be performed. + * + * General rules: + * 1. First 4 characters ' ##v' or IDENT_MAGIC represent kind of a magic number + * to identify the following strings after easily. Don't change them! + * + * 2. First 2 digits after 'v' or CCP_MAJOR are updated with U-Boot version + * change, e.g. from 2015.04 to 2018.03 + * + * 3. Second 2 digits after '.' or CCP_MINOR are updated if we want to upgrade + * U-Boot within an U-Boot version. + */ +#define CCP_IDENT_MAGIC " ##v" +#define GENERATE_CCP_VERSION(MAJOR, MINOR) CCP_IDENT_MAGIC MAJOR "." MINOR diff --git a/include/configs/siemens-env-common.h b/include/configs/siemens-env-common.h new file mode 100644 index 0000000000..36fa5d936f --- /dev/null +++ b/include/configs/siemens-env-common.h @@ -0,0 +1,201 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ + +/* Common env settings */ + +/** set_bootargs() + * input: + * console: string, tty, etc. + * baudrate: string, tty baudrate + * testargs: string + * optargs: string + * output: + * bootargs: string, default boot string + */ +#define ENV_BOOTARGS_DEFAULT "set_bootargs=" \ + "setenv bootargs " \ + "console=${console} " \ + "${testargs} " \ + "${optargs}\0" + +/** set_bootargs_net() + * input: + * kernel_name: + * dtb_name: + * project_dir: + * output: + */ +#define ENV_NET_FCT_NETARGS "set_bootargs_net=" \ + "run set_bootargs;" \ + "setenv bootfile ${project_dir}/boot/${kernel_name};" \ + "setenv bootdtb ${project_dir}/boot/${dtb_name_nfs}.dtb;" \ + "setenv rootpath /home/projects/${project_dir}/;" \ + "setenv bootargs ${bootargs} " \ + "root=/dev/nfs " \ + "nfsroot=${serverip}:${rootpath},${nfsopts} " \ + "ip=${ipaddr}:${serverip}:" \ + "${gatewayip}:${netmask}:${hostname}:eth0:off\0" + +/** net_nfs() + * input: + * output: + */ +#define ENV_NET_FCT_BOOT "net_nfs=" \ + "echo Booting from network ...; " \ + "run set_bootargs_net; " \ + "tftpboot ${dtb_loadaddr} ${serverip}:${bootdtb};" \ + "if test $? -eq 1;" \ + "then " \ + "echo Loading default.dtb!;" \ + "tftpboot ${dtb_loadaddr} ${serverip}:${project_dir}/boot/${dtb_name_default}.dtb;" \ + "fi;" \ + "tftpboot ${kernel_loadaddr} ${serverip}:${bootfile};" \ + "printenv bootargs;" \ + "booti ${kernel_loadaddr} - ${dtb_loadaddr}\0" + +/** check_update() + * input: + * upgrade_available: [0|1], if set to 1 check bootcount variables + * bootcount: int, bootcount + * bootlimit: int, limit cootcount + * toggle_partition(): - toggles active partition set + * output: + * upgrade_available: [0|1], set to 0 if bootcount > bootlimit + */ +#define ENV_FCT_CHECK_UPGRADE "check_upgrade="\ + "if test ${upgrade_available} -eq 1; " \ + "then " \ + "echo upgrade_available is set; " \ + "if test ${bootcount} -gt ${bootlimit}; " \ + "then " \ + "setenv upgrade_available 0;" \ + "echo toggle partition;" \ + "run toggle_partition;" \ + "fi;" \ + "fi;\0" + +/** toggle_partition() + * input: + * partitionset_active: [A|B], selected partition set + * output: + * partitionset_active: [A|B], toggle + */ +#define ENV_FCT_TOGGLE_PARTITION "toggle_partition="\ + "setenv ${partitionset_active} true;" \ + "if test -n ${A}; " \ + "then " \ + "setenv partitionset_active B; " \ + "env delete A; " \ + "fi;" \ + "if test -n ${B}; "\ + "then " \ + "setenv partitionset_active A; " \ + "env delete B; " \ + "fi;" \ + "saveenv\0" + +/** set_partition() + * input: + * partitionset_active: [A|B], selected partition set + * rootfs_name: string, mmc device file in kernel, e.g. /dev/mmcblk0 + * output: + * mmc_active_vol: string, mmc partition device file in kernel, e.g. /dev/mmcblk0p2 + * mmc_part_nr: int, partition number of mmc, e.g. /dev/mmcblk0p2 --> 2 + */ +#define ENV_EMMC_FCT_SET_ACTIVE_PARTITION "set_partition=" \ + "setenv ${partitionset_active} true;" \ + "if test -n ${A}; " \ + "then " \ + "setenv mmc_part_nr 1;" \ + "fi;" \ + "if test -n ${B}; " \ + "then " \ + "setenv mmc_part_nr 2;" \ + "fi;" \ + "setenv mmc_active_vol ${rootfs_name}p${mmc_part_nr} \0" + +/** set_bootargs_mmc() + * input: + * bootargs: string, default bootargs + * mmc_active_vol string, mmc partition device file in kernel, e.g. /dev/mmcblk0p2 + * ip_method: string, [none|?] + * output: + * bootargs: string + */ +#define ENV_EMMC_FCT_SET_EMMC_BOOTARGS "set_bootargs_mmc=" \ + "setenv bootargs ${bootargs} " \ + "root=${mmc_active_vol} rw " \ + "rootdelay=1 rootwait " \ + "rootfstype=ext4 " \ + "ip=${ip_method} \0" + +/** mmc_load_bootfiles() + * input: + * mmc_part_nr: + * dtb_loadaddr: + * dtb_name: + * kernel_loadaddr: + * kernel_name: + */ +#define ENV_EMMC_FCT_LOADFROM_EMMC "mmc_load_bootfiles=" \ + "echo Loading from eMMC ...;" \ + "ext4load mmc 0:${mmc_part_nr} ${dtb_loadaddr} boot/${dtb_name}.dtb;" \ + "if test $? -eq 1;" \ + "then " \ + "echo Loading default.dtb!;" \ + "ext4load mmc 0:${mmc_part_nr} ${dtb_loadaddr} boot/${dtb_name_default}.dtb;" \ + "fi;" \ + "ext4load mmc 0:${mmc_part_nr} ${kernel_loadaddr} boot/${kernel_name};" \ + "printenv bootargs;\0" + +/** mmc_boot() + * input: + * mmc_part_nr: + * dtb_loadaddr: + * dtb_name: + * kernel_loadaddr: + * kernel_name: + */ +#define ENV_EMMC_FCT_EMMC_BOOT "mmc_boot=" \ + "run set_bootargs;" \ + "run check_upgrade; " \ + "run set_partition;" \ + "run set_bootargs_mmc;" \ + "run mmc_load_bootfiles;" \ + "echo Booting from eMMC ...; " \ + "booti ${kernel_loadaddr} - ${dtb_loadaddr} \0" + +#define ENV_EMMC_ALIASES "" \ + "flash_self=run mmc_boot\0" \ + "flash_self_test=setenv testargs test; " \ + "run mmc_boot\0" + +#define ENV_COMMON "" \ + "project_dir=targetdir/rootfs\0" \ + "serverip=192.168.251.2\0" \ + "ipaddr=192.168.251.1\0" \ + "dtb_name_nfs=default\0" \ + "dtb_name_default=default\0" \ + "kernel_name=Image\0" \ + "partitionset_active=A\0" \ + "dtb_loadaddr=0x83000000\0" \ + "kernel_loadaddr=0x80280000\0" \ + "ip_method=none\0" \ + "rootfs_name=/dev/mmcblk0\0" \ + "upgrade_available=0\0" \ + "bootlimit=3\0" \ + "altbootcmd=run bootcmd\0" \ + "optargs=\0" \ + +/**********************************************************************/ + +#define ENV_EMMC ENV_EMMC_FCT_EMMC_BOOT \ + ENV_EMMC_FCT_LOADFROM_EMMC \ + ENV_EMMC_FCT_SET_EMMC_BOOTARGS \ + ENV_EMMC_FCT_SET_ACTIVE_PARTITION \ + ENV_FCT_CHECK_UPGRADE \ + ENV_EMMC_ALIASES \ + ENV_FCT_TOGGLE_PARTITION + +#define ENV_NET ENV_NET_FCT_BOOT \ + ENV_NET_FCT_NETARGS \ + ENV_BOOTARGS_DEFAULT -- 2.39.5