- Add SD secure boot target for ls1046ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size
as header is appended to u-boot image. So header will also be
copied from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for the
header.
- Reduce the size of CAAM driver for SPL Blobification functions
and descriptors, that are not required at the time of SPL are
disabled. Further error code conversion to strings is disabled
for SPL build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript
from NAND to DDR. Offsets for Bootscript on NAND and DDR have been
also defined.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Thu, 30 Mar 2017 04:23:13 +0000 (09:53 +0530)]
armv8: ls1046ardb: SPL size reduction
Using changes in this patch we were able to reduce approx 4k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1046ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1046ardb/ls1046ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1046a_common.h & ls1046ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Thu, 30 Mar 2017 04:22:38 +0000 (09:52 +0530)]
armv8: ls1043ardb: SPL size reduction
Using changes in this patch we were able to reduce approx 10k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1043ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1043ardb/ls1043ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1043a_common.h & ls1043ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
5. Remove I2C driver support from SPL in case of LS1043ARDB.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Depending on DDR configuration, gcc-6.x will show up unused-const-
variable messages. Use __maybe_unused specifier for all dynamic_odt
variable definitions to remove these warnings.
Memory footprint will not increase as gcc will optimize out unused
constants.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com> Signed-off-by: York Sun <york.sun@nxp.com>
Tom Rini [Fri, 14 Apr 2017 14:06:28 +0000 (10:06 -0400)]
buildman: Translate more strings to latin-1
When writing out some of our results we may now have UTF-8 characters
in there as well. Translate these to latin-1 and ignore any errors (as
this is for diagnostic and given the githash anything else can be
reconstructed by the user.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
which caused part_init to be called when it was not previously.
Without this patch, the following happens when a USB sd card reader is used.
=> usb start
starting USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 3 USB Device(s) found
scanning usb for storage devices... Device NOT ready
Request Sense returned 02 3A 00
### ERROR ### Please RESET the board ###
Eddie Cai [Thu, 6 Apr 2017 03:37:04 +0000 (11:37 +0800)]
usb: dwc2: invalidate the dcache before starting the DMA
We should invalidate the dcache before starting the DMA. In case there are
any dirty lines from the DMA buffer in the cache, subsequent cache-line
replacements may corrupt the buffer in memory while the DMA is still going on.
Cache-line replacement can happen if the CPU tries to bring some other memory
locations into the cache while the DMA is going on.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com> Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Philipp Tomsich [Thu, 6 Apr 2017 14:58:53 +0000 (16:58 +0200)]
usb: dwc3: gadget: make cache-maintenance on event buffers more robust
Merely using dma_alloc_coherent does not ensure that there is no stale
data left in the caches for the allocated DMA buffer (i.e. that the
affected cacheline may still be dirty).
The original code was doing the following (on AArch64, which
translates a 'flush' into a 'clean + invalidate'):
# during initialisation:
1. allocate buffers via memalign
=> buffers may still be modified (cached, dirty)
# during interrupt processing
2. clean + invalidate buffers
=> may commit stale data from a modified cacheline
3. read from buffers
This could lead to garbage info being written to buffers before
reading them during even-processing.
To make the event processing more robust, we use the following sequence
for the cache-maintenance:
# during initialisation:
1. allocate buffers via memalign
2. clean + invalidate buffers
(we only need the 'invalidate' part, but dwc3_flush_cache()
always performs a 'clean + invalidate')
# during interrupt processing
3. read the buffers
(we know these lines are not cached, due to the previous
invalidation and no other code touching them in-between)
4. clean + invalidate buffers
=> writes back any modification we may have made during event
processing and ensures that the lines are not in the cache
the next time we enter interrupt processing
Note that with the original sequence, we observe reproducible
(depending on the cache state: i.e. running dhcp/usb start before will
upset caches to get us around this) issues in the event processing (a
fatal synchronous abort in dwc3_gadget_uboot_handle_interrupt on the
first time interrupt handling is invoked) when running USB mass
storage emulation on our RK3399-Q7 with data-caches on.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Thu, 6 Apr 2017 14:58:52 +0000 (16:58 +0200)]
usb: dwc3: ensure consistent types for dwc3_flush_cache
The dwc3_flush_cache() call was declared and used inconsistently:
* The declaration assumed 'int' for addresses (a potential issue
when running in a LP64 memory model).
* The invocation cast the address to 'long'.
This change ensures that both the declaration and usage of this
function consistently uses 'uintptr_t' for correct behaviour even
when the allocated buffers (to be flushed) reside outside of the
lower 32bits of memory.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Felipe Balbi [Wed, 22 Feb 2017 15:12:40 +0000 (17:12 +0200)]
usb: gadget: g_dnl: only set iSerialNumber if we have a serial#
We don't want to claim that we support a serial number string and
later return nothing. Because of that, if g_dnl_serial is an empty
string, let's skip setting iSerialNumber to a valid number.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Wed, 22 Feb 2017 15:12:39 +0000 (17:12 +0200)]
usb: gadget: g_dnl: hold maximum string descriptor
A USB String descriptor can be up to 255 characters long and it's not
NULL terminated according to the USB spec. This means our
MAX_STRING_SERIAL should be 256 (to cope with NULL terminator).
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Checking the source code, we found that the variable "pixels"
gets a wrong value:
int pixels = VIDEO_FONT_HEIGHT * vid_priv->line_length;
"pixels" here means the value of pixels for a character, rather
than the bytes for a character. So the variable "pixels" is 4
times bigger than it's exact value, which will cause the memory
overflow when the cpu runs the following code:
Kever Yang [Fri, 10 Mar 2017 04:05:14 +0000 (12:05 +0800)]
usb: dwc2: add support for external vbus supply
Some board do not use the dwc2 internal VBUS_DRV signal, but
use a gpio pin to enable the 5.0V VBUS power, add interface to
enable the power in dwc2 driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Simon Glass <sjg@chromium.org>
arm: socfpga: sr1500 use environment in common header
This removes the default environment from the sr1500 header
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
This board has no upstream devicetree in the kernel source,
so set to socfpga_cyclone5_sr1500.dtb.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
- set devicetree name to match socfpga_{fpga model}_{board model}.dts
pattern
arm: socfpga: Socrates use environment in common header
This removes the default environment from the socrates headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
arm: socfpga: SoCKit use environment in common header
This removes the default environment from the SoCKit headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
arm: socfpga: DE1 use environment in common header
This removes the default environment from the de1 headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
This board does not have a devicetree in the upstream kernel
source so set devicetree to socfpga_cyclone5_de1_soc.dtb.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in V2:
- Remove unneeded CONFIG_BOOTFILE
- set devicetree name to match socfpga_{fpga model}_{board model}.dts
pattern
arm: socfpga: C5 SoCDK use environment in common header
This removes the default environment from the C5 SoCDK headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
In addition to the above, add support to boot from the custom
a2 type partition.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
arm: socfpga: A5 SoCDK use environment in common header
This removes the default environment from the A5 socdk headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Add support to boot from the custom a2 type partition.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v3:
- Fix small typo in defconfig, missing "C"
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
- Fix dtb name
arm: socfpga: DE0 use environment in common header
This removes the default environment from the de0 headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
In addition to the above, add support to boot from the custom
a2 type partition
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
arm: socfpga: Add distro boot to socfpga common header
This adds a common environment and support for distro boot
in the common socfpga header.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v5:
- Per Frank, to support OpenSuse the ENV must be after the GPT
Changes in v4:
- Move env back to being right after the MBR
Changes in v3:
- fix spacing between asterix
- remove verify=n as a default setting
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE and fdt_addr
- cleanup spacing in MMC env size
Chee, Tien Fong [Wed, 29 Mar 2017 03:49:16 +0000 (11:49 +0800)]
ARM: socfpga: boot0 hook: remove macro from boot0 header file
Commit ce62e57fc571 ("ARM: boot0 hook: remove macro, include whole
header file") miss out cleaning macro in this header file, and this
has broken implementation of a boot header capability in socfpga
SPL. Remove the macro in this file, and recovering it back
to proper functioning.
With the port C enabled, we can read the GPI input state of:
* the DIP switches (USER_DIPSW_HPS[3:0]/HPS_GPI[7:4])
* the push buttons (USER_PB_HPS[3:0]/HPS_GPI[11:8])
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Signed-off by: Sid-Ali Teir <git.syedelec@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Marek Vasut <marex@denx.de>
Stephen Arnold [Fri, 24 Mar 2017 01:58:08 +0000 (18:58 -0700)]
ARM: socfpga: add fpga build and bsp handoff instructions to readme
This patch adds the steps to manually (re)build a Quartus FPGA project,
generate the required BSP glue, and update u-boot handoff files for
mainline SPL support. Requires Quartus toolchain and current U-Boot.
Signed-off-by: Steve Arnold <stephen.arnold42@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de>
Stefan Agner [Tue, 11 Apr 2017 05:42:14 +0000 (11:12 +0530)]
board: toradex: colibri_vf: Add DCU support for Colibri Vybrid
The Vybrid SoC family has the same display controller unit (DCU)
like the LS1021A SoC. This patch adds platform data, pinmux defines
and clock control to enable the driver for Toradex Colibri Vybrid
module.
DCU_LAYER_MAX_NUM is currently used for DCU_MODE_BLEND_ITER and it
actually overflows the maximum value of BLEND_ITER for Vybrid and
LS102XA. Fix this by using a default value of 2.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Stefan Agner [Tue, 11 Apr 2017 05:42:11 +0000 (11:12 +0530)]
video: fsl_dcu_fb: Enable pixel clock after initialization
When enabling the DCU and pixel clock, the test mode is activated
since this is the reset configuration. The test mode immediately
shows a red screen on a LCD. A moment later, the DCU gets
initialized properly.
This patch enables the pixel clock after initialization of the DCU
control register. This avoids this initial flicker on LCD screens.
While at it change the polarity of pixel clock to display samples
data on the rising edge.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Reviewed-by: Alison Wang <alison.wang@nxp.com>
Stefan Agner [Tue, 11 Apr 2017 05:42:10 +0000 (11:12 +0530)]
video: fsl_dcu_fb: fix framebuffer to the end of memory
Fix the framebuffer location to the very end of the available memory.
This allows to remove the area from available memory for the kernel,
which in turn allows to display the splash screen through the Linux
kernel boot process.
Ideas has been taken from the sunxi display driver, e.g. 20779ec3a5 ("sunxi: video: Dynamically reserve framebuffer memory")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Alex Deymo [Sun, 2 Apr 2017 08:24:34 +0000 (01:24 -0700)]
mmc: sdhci: Wait for SDHCI_INT_DATA_END when transferring.
sdhci_transfer_data() function transfers the blocks passed up to the
number of blocks defined in mmc_data, but returns immediately once all
the blocks are transferred, even if the loop exit condition is not met
(bit SDHCI_INT_DATA_END set in the STATUS word).
When doing multiple writes to mmc, returning right after the last block
is transferred can cause the write to fail when sending the
MMC_CMD_STOP_TRANSMISSION command right after the
MMC_CMD_WRITE_MULTIPLE_BLOCK command, leaving the mmc driver in an
unconsistent state until reboot. This error was observed in the rpi3
board.
This patch waits for the SDHCI_INT_DATA_END bit to be set even after
sending all the blocks.
Test: Reliably wrote 2GiB of data to mmc in a rpi3.
Signed-off-by: Alex Deymo <deymo@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
The linux kernel driver for this module does not use a delay when
writing to the SDHCI_BUFFER register. This patch mimics that behavior
in order to speed up the mmc writes on the Raspberry Pi.
Signed-off-by: Alex Deymo <deymo@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Thu, 13 Apr 2017 02:29:22 +0000 (10:29 +0800)]
mmc: gen_atmel_mci: add driver model support for mci
Add the driver model support for Atmel mci while retaining the
existing legacy code. This allows the driver to support boards
that have converted to driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Carlo Caione [Wed, 12 Apr 2017 18:30:42 +0000 (20:30 +0200)]
mmc: meson: add MMC driver for Meson GX (S905)
This driver implements MMC support on Meson GX (S905) based systems.
It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring
Signed-off-by: Carlo Caione <carlo@caione.org> Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Tested-by: Vagrant Cascadian <vagrant@debian.org>
Wenyou Yang [Thu, 13 Apr 2017 02:31:20 +0000 (10:31 +0800)]
board: sama5d4ek: clean up code
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Wenyou Yang [Thu, 13 Apr 2017 02:31:19 +0000 (10:31 +0800)]
board: sama5d4ek: update to support DM/DT
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Wenyou Yang [Thu, 13 Apr 2017 02:31:17 +0000 (10:31 +0800)]
board: sama5d4_xplained: clean up code
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Wenyou Yang [Thu, 13 Apr 2017 02:31:16 +0000 (10:31 +0800)]
board: sama5d4_xplained: update to support DM/DT
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Wenyou Yang [Fri, 24 Mar 2017 03:34:06 +0000 (11:34 +0800)]
ARM: at91: lds: use "_image_binary_end" for DT location
The MMC SPL locates the BSS section to a different memory region
from text, then use "_image_binary_end" variable to point to the
correct device tree location.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Fri, 24 Mar 2017 01:18:44 +0000 (09:18 +0800)]
ARM: dts: at91: add dts file for sama5d4ek
Add the device tree file for sama5d4ek board.
The dts file is copied from Linux-4.4, do the following changes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Fri, 24 Mar 2017 01:18:43 +0000 (09:18 +0800)]
ARM: dts: at91: add dts files for sama5d4 Xplained
Add the device tree files for sama5d4 Xplained board.
The dts files are copied from Linux-4.4, do the following changes.
- add reg property for pinctrl node.
- move the gpio nodes(pioA, pioB, pioC ...) from the pinctrl child's
nodes to its slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Fri, 24 Mar 2017 01:18:42 +0000 (09:18 +0800)]
ARM: at91: dt: add dts file for sama5d3 Xplained
Add the device tree file for sama5d3 Xplained board.
The dts files are copied from the Linux-4.9, do changes as below.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Fri, 24 Mar 2017 01:18:41 +0000 (09:18 +0800)]
ARM: at91: dt: add dts files for sama5d3xek board
Add the device tree files for sama5d3xek board.
The dts files are copied from Linux-4.9, do the changes as below.
- add reg property for the pinctrl node.
- move the gpio nodes (pioA, pioB, pioC ...) as the pinctrl's
slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
- add spi0 node aliases.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Thu, 23 Mar 2017 04:44:37 +0000 (12:44 +0800)]
pinctrl: at91: add pinctrl driver
AT91 PIO controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.
Each SoC will have to describe the its limitation and pin
configuration via device tree. This will allow to do not need
to touch the C code when adding new SoC if the IP version is
supported.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Thu, 23 Mar 2017 04:55:21 +0000 (12:55 +0800)]
mtd: nand: atmel: use another functions to set gpio value
Because there isn't the implementation of gpio_set/get_value()
and gpio_set/get_value() after the at91 gpio driver is converted
to support the driver model, use at91_set_gpio_value() and
at91_get_gpio_value()
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Thu, 23 Mar 2017 04:55:20 +0000 (12:55 +0800)]
ARM: at91: gpio: fix at91_set_gpio_value() define
When the CONFIG_ATMEL_LEGACY is undefined, according to the following
defines, at91_set_gpio_value() references to at91_set_pio_value(x, y)
with two parameters.
#define at91_set_gpio_value(x, y) at91_set_pio_value(x, y)
#define at91_get_gpio_value(x) at91_get_pio_value(x)
But there isn't the implementation of at91_set_pio_value(x, y) with
two parameters in U-Boot. This is an error.
Same as at91_get_gpio_value(x) define.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Not force to use python from PATH. Issue was noted when building with
Yocto, because python from the distro is always taken instead of
python-native built during Yocto process.
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 4 Apr 2017 19:00:19 +0000 (13:00 -0600)]
dm: core: Ensure DMA regions start up with the cache clean
There is a strange interaction with drivers which use DMA if the cache
starts off in a dirty state. Buffer space which the driver reads (but has
not previously written) can contain zero bytes from alloc_priv(). This can
cause corruption of the memory used by DMA for incoming data.
Fix this and add a comment to explain the problem.
This allows the dwc2 driver to work correctly with driver model, for
example.
core/uclass: Print name of device in uclass_find_device_by_seq()
uclass_find_device_by_seq() prints seq and req_seq when debugging is
enabled, but this information is not very useful by itself. Add the
name of he driver to this information. This improves debugging as it
shows which devices are being considered.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Simon Glass <sjg@chromium.org>
With Python 3.5.2 encode will throw an exception if val is a byte array.
Decode it to a string first. This assumes it's utf-8, if it's not valid
utf-8 it will throw an exception.
Signed-off-by: George McCollister <george.mccollister@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
os.read() returns a byte array in Python 3.5.2 and needs to be converted
into a string. Check if the returned value is an instance of bytes and
if it is decode it as a utf-8 string. If it is not a utf-8 encoded string
the decoding may fail with an exception.
Prior to this fix the comparisions check data == "" would fail when data
was b'' and would cause an infinite memory leaking loop. joins would
also fail with an exception below but due to the infinite loop it never
made it that far.
Signed-off-by: George McCollister <george.mccollister@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
serial: ns16550: Link in the DM driver when when using platdata
Do not condition the compilation of the U_BOOT_DRIVER by !OF_PLATDATA.
This is inconsistent with the majority of other drivers. This also
blocks OF_PLATDATA boards with an 16550-compatible serial from using
serial in SPL.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Added tweak for rock to avoid a TPL build failure: Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 12 Apr 2017 20:41:00 +0000 (16:41 -0400)]
sandbox: Change CONFIG_SANDBOX_BITS_PER_LONG to hard-coded
Instead of having CONFIG_SANDBOX_BITS_PER_LONG in sandbox.h set to 64
with a comment to change to 32 on a 32bit host, simply set this to 64 in
asm/types.h and have the comment be there.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Vignesh R [Mon, 10 Apr 2017 06:53:22 +0000 (12:23 +0530)]
tiny-printf: Add support for %p format
Add support for %p, %pa[p], %pM, %pm and %pI4 formats to tiny-printf.
%pM and %pI4 are widely used by SPL networking stack and is required if
networking support is desired in SPL.
%p, %pa and %pap are mostly used by debug prints and hence supported
only when DEBUG is enabled.
Before this patch:
$ size spl/u-boot-spl
text data bss dec hex filename
99325 4899 218584 322808 4ecf8 spl/u-boot-spl
After this patch (with CONFIG_SPL_NET_SUPPORT):
$ size spl/u-boot-spl
text data bss dec hex filename
99666 4899 218584 323149 4ee4d spl/u-boot-spl
So, this patch adds ~350 bytes to code size.
If CONFIG_SPL_NET_SUPPORT is not enabled, this adds ~25 bytes.
If CONFIG_USE_TINY_PRINTF is disabled then:
$ size spl/u-boot-spl
text data bss dec hex filename
101116 4899 218584 324599 4f3f7 spl/u-boot-spl
So, there is still ~1.4K space saved even with support for %pM/%pI4.
Compiler used is to build is:
arm-linux-gnueabihf-gcc (Linaro GCC 6.2-2016.11) 6.2.1 20161016
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log