Simon Glass [Tue, 22 Aug 2023 03:16:55 +0000 (21:16 -0600)]
initcall: Support manual relocation
Move the manual-relocation code to the initcall file. Make sure to avoid
manually relocating event types. Only true function pointers should be
relocated.
Simon Glass [Tue, 22 Aug 2023 03:16:54 +0000 (21:16 -0600)]
initcall: Support emitting events
At present the initcall list consists of a list of function pointers. Over
time the initcall lists will likely change to mostly emitting events,
since most of the calls are board- or arch-specific.
As a first step, allow an initcall to be an event type instead of a
function pointer. Add the required macro and update initcall_run_list() to
emit an event in that case, or ignore it if events are not enabled.
The bottom 8 bits of the function pointer are used to hold the event type,
with the rest being all ones. This should avoid any collision, since
initcalls should not be above 0xffffff00 in memory.
Convert misc_init_f over to use this mechanism.
Add comments to the initcall header file while we are here. Also fix up
the trace test to handle the change.
Simon Glass [Tue, 22 Aug 2023 03:16:52 +0000 (21:16 -0600)]
initcall: Adjust the failure message and return value
Move the failure message outside the loop, so it is easier to follow the
code. Avoid swallowing the error code - just pass it along.
Drop the initcall-list address from the output. This is confusing since
we show two addresses. Really it is only the function address which is
useful, since it can be looked up in the map, e.g. with:
Simon Glass [Tue, 22 Aug 2023 03:16:51 +0000 (21:16 -0600)]
initcall: Adjust the loop logic
Use a variable to hold the function, so we don't need to repeat the
pointer access each time. Rename the init pointer to 'ptr' since we only
refer to it in the for() statement now.
Tom Rini [Thu, 31 Aug 2023 16:23:36 +0000 (12:23 -0400)]
Merge branch '2023-08-30-assorted-code-improvements' into next
- pcie-bcmstb improvements, nvmxip improvements, fix a corner case in
the serial uclass, send error messages to stderr in host tools, fwu
library CI state fixup, turn some setexpr diagnostic messages to debug
Marek Vasut [Wed, 23 Aug 2023 00:18:19 +0000 (02:18 +0200)]
drivers/mtd/nvmxip: Print phys_addr_t without warnings on both 32bit and 64bit systems
Cast the address such that it can be printed without warnings
on both 32bit and 64bit systems. This really should use some
better print formatter, but for the lack of it, do it this way.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Wed, 23 Aug 2023 00:18:18 +0000 (02:18 +0200)]
drivers/mtd/nvmxip: Rework the read accessor to support 32bit systems
Get rid of nvmxip_mmio_rawread() and just implement the readl()/readq()
reader loop within nvmxip_blk_read(). Cast the destination buffer as
needed and increment the read by either 4 or 8 bytes depending on if
this is systemd with 32bit or 64bit physical address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Wed, 23 Aug 2023 00:18:17 +0000 (02:18 +0200)]
drivers/mtd/nvmxip: Trigger post bind as probe on driver level
Perform all the block device creation only once, after the driver itself
successfully bound. Do not do this in uclass post bind, as this might be
triggered multiple times. For example the ut_dm_host test triggers this
and triggers a memory leak that way, since there are now multiple block
devices created using the blk_create_devicef() .
To retain the old probe-on-boot behavior, set DM_FLAG_PROBE_AFTER_BIND
flag in uclass post_bind callback, so the driver model would probe the
driver at the right time.
Rename the function as well, to match similar functions in
other block-related subsystems, like the mmc one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Wed, 23 Aug 2023 00:16:52 +0000 (02:16 +0200)]
fwu: Initialize global fwu library state during CI test
The current CI test worked by sheer luck, the g_dev global pointer
in the fwu library was never initialized and the test equally well
failed on sandbox64. Trigger the main loop in sandbox tests too to
initialize that global state, and move the sandbox specific exit
from fwu_boottime_checks after g_dev is initialized.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Maksim Kiselev [Fri, 18 Aug 2023 09:34:30 +0000 (12:34 +0300)]
serial-uclass: reset gd->cur_serial_dev to NULL if serial not found
Reset gd->cur_serial_dev pointer to avoid calling non-relocated code
from relocated code if a serial driver is not found and
CONFIG_REQUIRE_SERIAL_CONSOLE is disabled.
Here is detailed explanation of what this patch is trying to fix.
U-boot calls the serial_find_console_or_panic() function twice.
The first console setup occurs before U-boot relocation in
the serial_init(). This stage uses simple FDT parsing and
assigns gd->cur_serial_dev to a "serial" device that lives in
non-relocated code too.
The second console setup after U-boot relocation(from serial_initialize())
may use full live DT (if OF_LIVE enabled) probe sequence with buses,
clocks, resets, etc... And if the console setup fails at this step,
than we should be caught by panic_str("No serial driver found").
But... If we disable CONFIG_REQUIRE_SERIAL_CONSOLE, than we
return from serial_init() with gd->cur_serial_dev pointing
to the "old"(non-relocated) serial device.
And if this area, where "old" serial device is placed, is changed
(e.g. Linux kernel may be relocated at this address), than we will get
an unexpected crash on the next call of printf().
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
The make by default cuts off the stdout output from external tools,
so all error messages from the image-host are not shown in a make
output. Besides that, it is a common approach to use stderr stream
for error messages.
Use stderr for all error messages in image-host.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Reviewed-by: Simon Glass <sjg@chromium.org>
Sam Edwards [Wed, 16 Aug 2023 22:27:53 +0000 (15:27 -0700)]
pci: pcie-brcmstb: do not rely on CLKREQ# signal
When the Broadcom STB PCIe controller is initialized, it must be set
into one of three CLKREQ# modes: "none"/"aspm"/"l1ss". The Linux driver,
through today, hard-codes "aspm" since the vast majority of boards using
this driver have a fixed PCIe bus with the CLKREQ# signal wired up.
The Raspberry Pi CM4, however, can be connected to a plethora of PCIe
devices, some of which do not connect the CLKREQ# line (they just leave
it floating). So "aspm" mode is no longer appropriate in all cases. In
Linux, there is a proposed patchset [1] to determine the proper mode.
This doesn't really make sense in U-Boot's case, so we just change the
assumption from "aspm" to "none" (which is always safe).
This patch DOES resolve a real-world crash that occurs when U-Boot is
running on a Raspberry Pi CM4 installed in slot 3 of a Turing Pi 2
cluster board.
Sam Edwards [Mon, 14 Aug 2023 22:34:13 +0000 (16:34 -0600)]
pci: pcie-brcmstb: bring over some robustness improvements from Linux
Since the initial U-Boot driver was ported here from Linux, the latter
has had a few changes for robustness/stability. This patch brings over
two of them:
- Do not attempt to access the configuration space of a PCIe device if
the link has gone down, as that will result in an asynchronous SError
interrupt which will crash U-Boot.
- Wait for the recommended 100ms after PERST# is deasserted.
I sent this patch while debugging a crash involving PCIe, but these
are unrelated improvements. I do not believe that this patch fixes any
real-world bug.
Tom Rini [Tue, 29 Aug 2023 20:58:42 +0000 (16:58 -0400)]
Merge branch '2023-08-29-integrate-efi-capsule-update-better-in-to-u-boot-buildflow' into next
To quote the author:
This patchset aims to bring two capsule related tasks under the U-Boot
build flow.
The first task is related to generation of capsules. The capsules can be
generated as part of U-Boot build, and this is being achieved through
binman, by adding a capsule entry type. The capsules can be generated by
specifying the capsule parameters as properties under the capsule entry
node.
The other task is the embedding of the public key into the platform's
DTB. The public key is in the form of an EFI Signature List(ESL) file
and is used for capsule authentication. This is being achieved by adding
the signature node containing the capsule public key in the platform's
DTB.
Corresponding changes have also been made to the test setup of the EFI
capsule update feature. The ESL public key file was embedded into the
sandbox platform's test.dtb as part of the test setup, post U-Boot
build. This is now no longer needed as the embedding of the ESL happens
as part of the build.
Secondly, the capsules needed for testing the EFI capsule update feature
were being generated through the invocation of the mkeficapsule tool.
This setup has also been changed to introduce generation of these
capsules through binman.
The document has been updated to reflect the above changes.
Sughosh Ganu [Tue, 22 Aug 2023 17:40:07 +0000 (23:10 +0530)]
test: capsule: Remove logic to add public key ESL
The public key EFI Signature List(ESL) needed for capsule
authentication is now embedded into the platform's DTB as part of the
build. Remove the superfluous logic from the test setup.
Sughosh Ganu [Tue, 22 Aug 2023 17:40:06 +0000 (23:10 +0530)]
sandbox: capsule: Add path to the public key ESL file
Add the path to the public key EFI Signature List(ESL) file for the
sandbox variants which enable capsule authentication. This ESL file
gets embedded into the platform's device-tree as part of the build.
Sughosh Ganu [Tue, 22 Aug 2023 17:40:05 +0000 (23:10 +0530)]
scripts/Makefile.lib: Embed capsule public key in platform's dtb
The EFI capsule authentication logic in u-boot expects the public key
in the form of an EFI Signature List(ESL) to be provided as part of
the platform's dtb. Currently, the embedding of the ESL file into the
dtb needs to be done manually.
Add a target for generating a dtsi file which contains the signature
node with the ESL file included as a property under the signature
node. Include the dtsi file in the dtb. This brings the embedding of
the ESL in the dtb into the U-Boot build flow.
The path to the ESL file is specified through the
CONFIG_EFI_CAPSULE_ESL_FILE symbol.
Sughosh Ganu [Tue, 22 Aug 2023 17:40:04 +0000 (23:10 +0530)]
scripts/Makefile.lib: Add dtsi include files as deps for building DTB
At the time of building the DTB, some dtsi files can be selected for
inclusion. Have these dtsi files as dependencies for the DTB
target. This also ensures generation or updating the dtsi files if
need be.
Sughosh Ganu [Tue, 22 Aug 2023 17:40:03 +0000 (23:10 +0530)]
scripts/Makefile.lib: Collate all dtsi files for inclusion
At the time of building a device-tree file, all the *u-boot.dtsi files
are looked for, in a particular order, and the first file found is
included. Then, the list of files specified in the
CONFIG_DEVICE_TREE_INCLUDES symbol are included.
Combine these files that are to be included into a variable, and then
include all these files in one go.
Sughosh Ganu [Tue, 22 Aug 2023 17:40:02 +0000 (23:10 +0530)]
sandbox: trace: Increase trace buffer size
When running the trace test on the sandbox platform, the current size
of 16MiB is no longer large enough for capturing the entire trace
history, and results in truncation. Use a size of 32MiB for the trace
buffer on the sandbox platform while running the trace test.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Sughosh Ganu [Tue, 22 Aug 2023 17:40:00 +0000 (23:10 +0530)]
test: capsule: Generate EFI capsules through binman
Support has been added for generating the EFI capsules through
binman. Make changes in the EFI capsule update testing feature to
generate capsules through binman.
Sughosh Ganu [Tue, 22 Aug 2023 17:39:59 +0000 (23:09 +0530)]
binman: capsule: Add support for generating EFI capsules
Add support in binman for generating EFI capsules. The capsule
parameters can be specified through the capsule binman entry. Also add
test cases in binman for testing capsule generation.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Sughosh Ganu [Tue, 22 Aug 2023 17:39:57 +0000 (23:09 +0530)]
sandbox: capsule: Enable EFI capsule module on sandbox variants
Enable the EFI capsule update code on all sandbox variants. This was
already enabled on the sandbox, sandbox64 and sandbox_flattree
variants. The rest of the variants also have the EFI capsule update
module enabled now. With this commit, the mkeficapsule tool also gets
enabled on all variants.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Sughosh Ganu [Tue, 22 Aug 2023 17:39:56 +0000 (23:09 +0530)]
sandbox: capsule: Add keys and certificates needed for capsule update testing
Add the private keys and public key certificates which are to be used
for capsule authentication while testing the EFI capsule update
functionality. There are two pairs of private and public keys, good
and bad. The good key pair will be used for signing capsules, whilst
the bad key pair is to be used as malicious keys for testing
authentication failure cases. The capsule_pub_key_good.crt is also
converted to an EFI Signature List(ESL) file, SIGNER.esl, which is
embedded in the platform's device-tree for capsule authentication.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Sughosh Ganu [Tue, 22 Aug 2023 17:39:54 +0000 (23:09 +0530)]
binman: bintool: Build a tool from a list of commands
Add support to build a tool from source with a list of commands. This
is useful when a tool can be built with multiple commands instead of a
single command.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Alexander Dahl [Wed, 23 Aug 2023 13:58:55 +0000 (15:58 +0200)]
board: sam9x60-curiosity: Let LED subsystem init leds if enabled
If CONFIG_LED and CONFIG_LED_GPIO are enabled, it is not necessary to
initialize the RGB LED on the board by manually setting hardcoded GPIOs
anymore. Everything is well defined in dts and can be used like on
boards of other vendors.
Keep the old behaviour as fallback, though.
With all this in place enabling CONFIG_CMD_LED gives us a working 'led'
command on the U-Boot shell.
Alexander Dahl [Wed, 23 Aug 2023 13:58:53 +0000 (15:58 +0200)]
configs: at91: sam9x60: Switch to new reset driver
Since commit 61040097a9d1 ("reset: at91: Add reset driver for basic
assert/deassert operations") the compatible "microchip,sam9x60-rstc" for
the sam9x60 reset controller in sam9x60.dtsi is not handled by
CONFIG_SYSRESET_AT91 anymore, but by CONFIG_RESET_AT91 now. This
resulted in the following error message, when trying to reset from
U-Boot shell:
U-Boot> reset
resetting ...
System reset not supported on this platform
### ERROR ### Please RESET the board ###
Fixed by enabling the new driver in the relevant defconfigs. Tested on
sam9x60-curiosity board. Defconfigs for sam9x60ek adapted in the same
way, but without testing. These should be all sam9x60 boards affected
in U-Boot here.
Alexander Dahl [Wed, 23 Aug 2023 13:58:52 +0000 (15:58 +0200)]
configs: at91: sam9x60_curiosity: Sync both defconfig variants
The board has two SD card slots and we have two defconfigs for booting
from either the first (micro SD) named 'sam9x60_curiosity_mmc_defconfig'
or the second (full size SD) named 'sam9x60_curiosity_mmc1_defconfig'.
For comparable Microchip boards (sama5d27-som1-ek, sama5d29-curiosity,
sama7g5ek) with two card slots the defconfigs only differ in BOOTARGS,
BOOTCOMMAND, and ENV_FAT_DEVICE_AND_PART and the same should be the case
for sam9x60_curiosity.
Here the 'mmc1' config has more options enabled to support the raw NAND
flash populated on the board, so the 'mmc' config (for mmc0) was adapted
by enabling additional options, instead of removing options from mmc1.
The 'mem=128M' argument can be dropped from kernel command line, because
it is redundant to memory node in dts in both Linux and U-Boot:
Tom Rini [Sat, 26 Aug 2023 15:25:08 +0000 (11:25 -0400)]
Merge branch '2023-08-26-bootstd-chromeos-impreovements-and-move-to-gcc-13.2' into next
First, update CI to using gcc-13.2 from 13.1, and rebuild the CI
containers. This is needed because the second part adds utilities for
tests and provides, to quote the author:
This updates the ChromiumOS bootmeth to detect multiple kernel
partitions on a disk.
It also includes minor code improvements to the partition drivers,
including accessors for the optional fields.
This series also includes some other related tweaks in testing.
Simon Glass [Thu, 24 Aug 2023 19:55:45 +0000 (13:55 -0600)]
bootstd: cros: Allow detection of any kernel partition
The existing ChromiumOS bootmeth only supports reading a single kernel
partition, either 2 or 4. In fact there are normally two options
available.
Use the GUID to detect kernel partitions, with the BOOTMETHF_ANY_PART
flag, so that bootstd does not require a valid filesystem before calling
the bootmeth.
Tidy up and improve the logging while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
[trini: Add missing select of PARTITION_TYPE_GUID] Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Thu, 24 Aug 2023 19:55:41 +0000 (13:55 -0600)]
bootstd: Add a test for bootmeth_cros
The ChromiumOS bootmeth has no tests at present. Before adding more
features. add a basic test.
This creates a disk which can be scanned by the bootmeth, so make sure
things work. It is quite rudimentary, since the kernel is faked, the root
disk is missing and there is no cmdline stored.
Enable the bootmeth for snow so it can build the unit test.
Simon Glass [Thu, 24 Aug 2023 19:55:38 +0000 (13:55 -0600)]
test: Move 1MB.fat32.img and 2MB.ext2.img
These are currently created in the source directory, which is not ideal.
Move them to the persistent-data directory instead. Update the test so
skip validating the filename, since it now includes a full path.
Simon Glass [Thu, 24 Aug 2023 19:55:37 +0000 (13:55 -0600)]
sandbox: Add a way to access persistent test files
Some pytests create files in the persistent-data directory. It is useful
to be able to access these files in C tests. Add a function which can
locate a file given its leaf name, using the environment variable set
up in test/py/conftest.py
Simon Glass [Thu, 24 Aug 2023 19:55:35 +0000 (13:55 -0600)]
dm: core: Correct error handling when event fails
Follow the correct path in device_probe() when and event handler fails.
This avoids getting into a strange state where the device appears to be
activated but is not.
Simon Glass [Thu, 24 Aug 2023 19:55:29 +0000 (13:55 -0600)]
part: nac: Use desc instead of dev_desc
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the mac code to
just use 'desc'.
Simon Glass [Thu, 24 Aug 2023 19:55:28 +0000 (13:55 -0600)]
part: iso: Use desc instead of dev_desc
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the iso code to
just use 'desc'.
Simon Glass [Thu, 24 Aug 2023 19:55:27 +0000 (13:55 -0600)]
part: efi: Use desc instead of dev_desc
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the efi code to
just use 'desc'.
Simon Glass [Thu, 24 Aug 2023 19:55:26 +0000 (13:55 -0600)]
part: dos: Use desc instead of dev_desc
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the dos code to
just use 'desc'.
Simon Glass [Thu, 24 Aug 2023 19:55:25 +0000 (13:55 -0600)]
part: amiga: Use desc instead of dev_desc
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the amiga code to
just use 'desc'.
Simon Glass [Thu, 24 Aug 2023 19:55:24 +0000 (13:55 -0600)]
part: Use desc instead of dev_desc
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the partition code to
just use 'desc', as is done with driver model.
Tom Rini [Fri, 25 Aug 2023 21:52:59 +0000 (17:52 -0400)]
Merge branch '2023-08-25-add-persistent-config-editor-via-expo' into next
To quote the author:
So far cedit does not support reading and writing the configuration.
This series add several features related to this:
First, it adds support for using a file on a filesystem. This is in
FDT format and provides enough information to reset the cedit back to
the saved settings.
Second, it adds support for using the U-Boot environment. Since the
environment is generally saved across reboots, this feature provides an
easy way of storing the state on most boards. The variables all have a
'c.' prefix to avoid confusion with other variables.
Finally it adds support for using CMOS RAM. This is commonly used on x86
devices to store BIOS settings. The expo schema provides information on
the register layout.
Some other minor tweaks and improvements are included along the way.
Simon Glass [Mon, 14 Aug 2023 22:40:37 +0000 (16:40 -0600)]
expo: cedit: Support writing settings to CMOS RAM
Add a command to write cedit settings to CMOS RAM so that it can be
preserved across a reboot. This uses a simple bit-encoding, where each
field has a 'bit position' and a 'bit length' in the schema.
Simon Glass [Mon, 14 Aug 2023 22:40:33 +0000 (16:40 -0600)]
expo: cedit: Support writing settings to a file
Support writing settings from an expo into a file in FDT format. It
consists of a single node with a two properties for each sceneitem,
one with tag ID chosen by the user and another for its text value.
Simon Glass [Mon, 14 Aug 2023 22:40:29 +0000 (16:40 -0600)]
expo: Add documentation for the configuration editor
This is mentioned in passing in the 'cedit' command. Its file format is
described under `expo`. But it would be better if it had its own entry
in the documentation.
Add a new 'cedit' entry with a few details about this feature.
Simon Glass [Mon, 14 Aug 2023 22:40:28 +0000 (16:40 -0600)]
expo: Tidy up the expo.py tool and usage
Tidy up this tool a little:
- define which arguments are needed
- split the enum values out into a header file
- warn if no enum values are found
- display the dtc error if something goes wrong
- avoid a Python traceback on error
Simon Glass [Mon, 14 Aug 2023 22:40:24 +0000 (16:40 -0600)]
expo: Refactor menu_build() to return the object created
The caller reads the ID but menu_build() does this again. Add the ID as
a parameter to avoid this. Return the object created so that the caller
can adjust it.
Tom Rini [Thu, 24 Aug 2023 21:42:48 +0000 (17:42 -0400)]
Merge branch '2023-08-24-enable-more-features-in-qemu-arm' into next
To quote the author:
Now that the driver for the Bochs VGA card emulated by QEMU is no longer
limited to x86 architectures, this series enables it on arm and arm64 virtual
machines to provide a graphical interface. In line with that series this also
enables console buffering and USB keyboard.
Tested with the Debian 12 installer using GRUB EFI:
doc: qemu: arm: Add a section on booting Linux distros
Add an example qemu-system-aarch64 command that can make U-Boot on QEMU
boot into the Debian Installer, along with resulting console messages
from U-Boot, based on the existing documentation section for the x86
version.
Commit 02be57caf730 ("riscv: qemu: Enable usb keyboard as an input
device") adds PCI xHCI support to QEMU RISC-V virtual machines and
enables using a USB keyboard as one of the input devices. Similarly,
enable those for ARM virtual machines as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng@tinylab.org>
Commit 608b80b5b855 ("riscv: qemu: Enable PRE_CONSOLE_BUFFER") enables
buffering console messages for QEMU RISC-V virtual machines so those
printed before the video console is available will still show up on the
display. Similarly, enable it for ARM virtual machines as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng@tinylab.org>
Commit 716161663ec49 ("riscv: qemu: Enable Bochs video support") enables
a video console for QEMU RISC-V virtual machines using an emulated Bochs
VGA card. Similarly, enable it for ARM virtual machines as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Bin Meng <bmeng@tinylab.org>
Marek Vasut [Wed, 16 Aug 2023 15:05:55 +0000 (17:05 +0200)]
ufs: Implement cache management
Add function to flush and invalidate cache over request and response
queue entries, and perform flush and optional invalidate over block
layer data that are passed into the UFS layer. This makes it possible
to use UFS with caches enabled.
Marek Vasut [Wed, 16 Aug 2023 15:05:54 +0000 (17:05 +0200)]
ufs: Use utp_transfer_req_desc pointer in ufshcd_get_tr_ocs
Use utp_transfer_req_desc pointer to reference to utrdl queue
instead of referencing the queue directly. This makes the code
more consistent. No functional change.
Marek Vasut [Wed, 16 Aug 2023 15:05:53 +0000 (17:05 +0200)]
ufs: Pass hba pointer to ufshcd_prepare_req_desc_hdr()
Pass the hba pointer itself to ufshcd_prepare_req_desc_hdr()
instead of duplicating utp_transfer_req_desc access at each
call site. No functional change.
projects / u-boot.git / log