Samuel Holland [Mon, 28 Nov 2022 07:02:28 +0000 (01:02 -0600)]
video: sunxi: dw-hdmi: Use DM for HVCC regulator
The HDMI PHY depends on the HVCC supply being enabled. So far we have
relied on it being enabled by an earlier firmware stage (SPL or TF-A).
Attempt to enable the regulator here, so we can remove that dependency.
Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Samuel Holland [Mon, 28 Nov 2022 07:02:27 +0000 (01:02 -0600)]
video: sunxi: dw-hdmi: Use DM for clock gates and resets
This abstracts away the CCU register layout, which is necessary for
supporting new SoCs like H6 with a reorganized CCU. One of the resets is
referenced from the PHY node instead of the controller node, so it will
have to wait until the PHY code is factored out to a separate driver.
Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
This driver is actually used for powerpc and m68k/ColdFire.
On ColdFire SoC's, interrupt flag get not set if IIEN flag (mbcr bit6,
interrupt enabled) is not set appropriately before each transfert.
As a result, the transfert hangs forever waiting for IIEN.
This patch set IIEN before each transfert, while considering this fix
as not harming powerpc arch.
Ye Li [Thu, 6 Apr 2023 10:26:35 +0000 (18:26 +0800)]
i2c: imx_lpi2c: Fix misuse the IS_ENABLED for DM clock
The IS_ENABLED, which does not consider SPL build, should be replaced
by CONFIG_IS_ENABLED.
For the case that we only enable DM CLK for u-boot but not in SPL, the
IS_ENABLED(CONFIG_CLK) still returns true, then cause clock failure.
Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Haibo Chen [Mon, 27 Mar 2023 11:21:43 +0000 (19:21 +0800)]
i2c: correct I2C deblock logic
Current code use dm_gpio_get_value() to get SDA and SCL value, and the
value depends on whether DTS file config the GPIO_ACTIVE_LOW. In ususal
case for i2c GPIO, DTS need to set GPIO_ACTIVE_LOW for SCL/SDA pins. So
here the logic is not correct.
And we must not use GPIOD_ACTIVE_LOW in client code include the
dm_gpio_set_dir_flags(), it is DTS's responsibility for this flag. So
remove GPIOD_ACTIVE_LOW here.
This code first figures out if there is an i2c,speeds property, if so
its size in u32s, and then reads the value into the local speeds[]
array. Both 'size' and 'speeds' are completely unused thereafter.
It's not at all clear what this is supposed to do. Of course, it could
be seen as a sanity check that the DT node does have an i2c,speeds
property with an appropriate number of elements, but for that one
wouldn't actually need to read it into speeds[]. Also, I can't find
anywhere else in the U-Boot code which makes use of values from that
property (this is is the only C code referencing "i2c,speeds"), so it
seems pointless to insist that it's there.
Pali Rohár [Sat, 11 Mar 2023 10:44:27 +0000 (11:44 +0100)]
mmc: Use EXT_CSD_EXTRACT_BOOT_PART() macro for extracting boot part
Mask macro PART_ACCESS_MASK filter out access bits of emmc register and
macro EXT_CSD_EXTRACT_BOOT_PART() extracts boot part bits of emmc register.
So use EXT_CSD_EXTRACT_BOOT_PART() when extracting boot partition.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Fri, 10 Feb 2023 12:23:50 +0000 (13:23 +0100)]
mmc: mv_sdhci: Simplify call to sdhci_mvebu_mbus_config()
This driver already depends on CONFIG_ARCH_MVEBU, so there is no need
to have some checks for this Kconfig symbol in the driver itself. Let's
remove these superfluous checks.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Loic Poulain [Thu, 26 Jan 2023 09:24:18 +0000 (10:24 +0100)]
mmc: erase: Use TRIM erase when available
The default erase command applies on erase group unit, and
simply round down to erase group size. When the start block
is not aligned to erase group size (e.g. erasing partition)
it causes unwanted erasing of the previous blocks, part of
the same erase group (e.g. owned by other logical partition,
or by the partition table itself).
To prevent this issue, a simple solution is to use TRIM as
argument of the Erase command, which is usually supported
with eMMC > 4.0, and allow to apply erase operation to write
blocks instead of erase group
Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Loic Poulain [Thu, 26 Jan 2023 09:24:17 +0000 (10:24 +0100)]
mmc: Check support for TRIM operations
When secure/insecure TRIM operations are supported.
When used as erase command argument it applies the
erase operation to write blocks instead of erase
groups.
Tom Rini [Sat, 8 Apr 2023 15:20:47 +0000 (11:20 -0400)]
Merge tag 'video-20230407' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix building sandbox without SDL
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
If console multiplexing in enabled (CONFIG_CONSOLE_MUX=y), the output of
the coninfo command should show the file association (stdin, stderr,
stdout) for all devices not only the default ones.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a reference document for the U-Boot documentation style.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Tue, 28 Feb 2023 01:55:23 +0000 (02:55 +0100)]
video: tl070wsh30: Fix use of CONFIG_IS_ENABLED on DM_REGULATOR
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Tue, 28 Feb 2023 01:55:22 +0000 (02:55 +0100)]
video: simple-panel: Fix use of CONFIG_IS_ENABLED on DM_REGULATOR
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Tue, 28 Feb 2023 01:55:21 +0000 (02:55 +0100)]
video: rm68200: Fix use of CONFIG_IS_ENABLED on DM_REGULATOR
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Tue, 28 Feb 2023 01:55:20 +0000 (02:55 +0100)]
video: otm8009a: Fix use of CONFIG_IS_ENABLED on DM_REGULATOR
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Tue, 28 Feb 2023 01:55:19 +0000 (02:55 +0100)]
mmc: npcm_sdhci: Fix use of CONFIG_IS_ENABLED on DM_REGULATOR
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Tue, 28 Feb 2023 01:55:18 +0000 (02:55 +0100)]
misc: ub251xb: Fix use of CONFIG_IS_ENABLED on DM_REGULATOR
The DM_REGULATOR symbol has SPL counterpart in:
drivers/power/regulator/Kconfig:config SPL_DM_REGULATOR
Use CONFIG_IS_ENABLED() macro to match on the correct
variant depending on the build stage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Svyatoslav Ryhel [Mon, 27 Mar 2023 08:11:48 +0000 (11:11 +0300)]
video: tegra20: add DSI controller driver
Adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features
like ganged mode won't work. Driver is heavily based on
mainline Tegra DSI and re-uses much of its features.
Only T30 is supported for now but T20 support can be added
if any supported devices will be found.
Driver is wrapped as panel driver since Tegra DC driver supports
only panel drivers calls.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF600T T30 Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30 Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Svyatoslav Ryhel [Mon, 27 Mar 2023 08:11:47 +0000 (11:11 +0300)]
video: tegra-dc: pass DC regmap to internal devices
Internal video devices like DSI and HDMI controllers
require sending commands into DC register field.
To make this available, lets create platform data,
which is restricted to pass DC regmap only to
pre-defined devices.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30 Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00 Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20 Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30 Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Svyatoslav Ryhel [Mon, 27 Mar 2023 08:11:46 +0000 (11:11 +0300)]
video: tegra-dc: add panel_set_backlight call
Tegra DC driver does not call panel_set_backlight, which can
result in absence of backlight on device. Fix this by calling
panel_set_backlight with BACKLIGHT_DEFAULT just after
panel_enable_backlight.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20 Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00 Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30 Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30 Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Svyatoslav Ryhel [Mon, 27 Mar 2023 08:11:43 +0000 (11:11 +0300)]
video: tegra-dc: request timings from panel driver first
Check if panel driver has display timings and get those.
If panel driver does not pass timing, try to find timing
under rgb node for backwards compatibility.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20 Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00 Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30 Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30 Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Marcel Ziswiler [Mon, 27 Mar 2023 08:11:40 +0000 (11:11 +0300)]
tegra: lcd: video: integrate display driver for t30
On popular request make the display driver from T20 work on T30 as
well. Turned out to be quite straight forward. However a few notes
about some things encountered during porting: Of course the T30 device
tree was completely missing host1x as well as PWM support but it turns
out this can simply be copied from T20. The only trouble compiling the
Tegra video driver for T30 had to do with some hard-coded PWM pin
muxing for T20 which is quite ugly anyway. On T30 this gets handled by
a board specific complete pin muxing table. The older Chromium U-Boot
2011.06 which to my knowledge was the only prior attempt at enabling a
display driver for T30 for whatever reason got some clocking stuff
mixed up. Turns out at least for a single display controller T20 and
T30 can be clocked quite similar. Enjoy.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30 Tested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de> # Surface RT T30 Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30 Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Hai Pham [Tue, 28 Feb 2023 21:37:08 +0000 (22:37 +0100)]
ARM: renesas: Add R8A779G0 V4H White Hawk board code
Add board code for R8A779G0 V4H White Hawk board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Tho Vu <tho.vu.wh@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message
Rename DTs to match Linux, which has dash between white-hawk]
Hai Pham [Tue, 28 Feb 2023 21:37:05 +0000 (22:37 +0100)]
ARM: dts: renesas: Add R8A779G0 V4H DT extras
Add R8A779G0 V4H DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Phong Hoang [Tue, 28 Feb 2023 21:37:04 +0000 (22:37 +0100)]
ARM: dts: renesas: Add R8A779G0 V4H DT
Add initial DT support for R8A779G0 (R-Car V4H). Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Hai Pham [Tue, 28 Feb 2023 21:37:03 +0000 (22:37 +0100)]
pinctrl: renesas: Add R8A779G0 V4H PFC tables
Add pinctrl tables for R8A779G0 V4H SoC.
Based on Linux next 20230228 PFC tables tables up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com> Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, sort sh_pfc_pinconf_set voltage args]
Hai Pham [Tue, 28 Feb 2023 21:37:02 +0000 (22:37 +0100)]
clk: renesas: Add R8A779G0 V4H clock tables
Add clock tables for R8A779G0 V4H SoC from Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
There is an adjustment to the clock tables to make them easier suitable
for U-Boot, PLL2 is not treated as GEN4 PLL type PLL2_VAR, but rather a
plain PLL2. This should be sufficient until PLL2_VAR is implemented in
the clock core.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228 . Update from CLK to CPG core driver
Treat PLL2 as non-PLL2_VAR for now]
Add all Clock Pulse Generator Core Clock Outputs for the
Renesas R-Car V4H (R8A779G0) SoC from Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Tho Vu <tho.vu.wh@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update to linux next 20230228 state]
Tho Vu [Tue, 28 Feb 2023 21:37:00 +0000 (22:37 +0100)]
dt-bindings: power: Add R8A779G0 V4H SYSC power domain definitions
Add power domain indices for R-Car V4H (R8A779G0) from Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Tho Vu <tho.vu.wh@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update to linux next 20230228 state]
Hai Pham [Tue, 28 Feb 2023 21:34:46 +0000 (22:34 +0100)]
ARM: renesas: Add R8A779F0 S4 Spider board code
Add board code for R8A779F0 S4 Spider board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Hai Pham [Tue, 28 Feb 2023 21:34:43 +0000 (22:34 +0100)]
ARM: dts: renesas: Add R8A779F0 S4 DT extras
Add R8A779F0 S4 DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Hai Pham [Tue, 28 Feb 2023 21:34:42 +0000 (22:34 +0100)]
ARM: dts: renesas: Add R8A779F0 S4 DT
Add initial DT for R8A779F0 S4 SoC. Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Hai Pham [Tue, 28 Feb 2023 21:34:41 +0000 (22:34 +0100)]
ARM: rmobile: Turn R-Car V3U into R-Car Gen4
Despite the name, R-Car V3U is the first member of the R-Car Gen4
family [1]. Hence reflect this in related files, select appropriate
configuration options and split DT build into its own GEN4 entry.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Deduplicate DTC_FLAGS addition using RCAR_64 symbol
Update commit message]
LUU HOAI [Tue, 28 Feb 2023 21:34:40 +0000 (22:34 +0100)]
pinctrl: renesas: Add R8A779F0 S4 PFC tables
Add pinctrl tables for R8A779F0 S4 SoC.
Based on Linux next 20230228 PFC tables tables up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Use RCAR_64 Kconfig, sync with Linux next 20230228]
Hai Pham [Tue, 28 Feb 2023 21:34:39 +0000 (22:34 +0100)]
clk: renesas: Add R8A779F0 S4 clock tables
Add clock tables for R8A779F0 S4 SoC
Based on Linux commit 24aaff6a6ce4 ("clk: renesas: cpg-mssr: Add support
for R-Car S4-8") by Yoshihiro Shimoda and sync the tables up to Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228 . Update from CLK to CPG core driver]
Marek Vasut [Tue, 28 Feb 2023 21:34:38 +0000 (22:34 +0100)]
clk: renesas: Update R-Car Gen3 driver Gen4 support
Update R-Car Gen4 support in Gen3 clock driver. This patch renames the
V3U clock parts to Gen4 and extends them by new PLL2, PLL3, PLL4, PLL6
as well as SDSRC clock which use undocumented bits so far, and RPCSRC
clock which uses its own more capable divider table. The Gen4 module
standby and reset tables are also updated.
This patch makes use of union to alias Gen3 and more extensive Gen4
PLL tables, as the driver cannot ever be instantiated on hardware
that would identify itself as both Gen3 and Gen4.
The V3U clock driver is updated to match Gen4 clock driver behavior,
it is augmented with a more extensive PLL table and a valid MODEMR
register offset.
This supersedes "clk: renesas: Introduce R-Car Gen4 CPG driver"
from Hai Pham as the R-Car Gen3 and Gen4 clock core drivers are
extremely similar. That implementation was in turn based on Linux
commit 470e3f0d0b15 ("clk: renesas: rcar-gen4: Introduce R-Car Gen4 CPG driver")
by Yoshihiro Shimoda .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add definitions for R8A779F0 S4 CPG Core Clock headers from Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Tho Vu <tho.vu.wh@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update to linux next 20230228 state]
Tho Vu [Tue, 28 Feb 2023 21:34:36 +0000 (22:34 +0100)]
dt-bindings: power: Add R8A779F0 S4 SYSC power domain definitions
Add power domain indices for R-Car S4 (R8A779F0) from Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Tho Vu <tho.vu.wh@renesas.com> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update to linux next 20230228 state]
Hai Pham [Tue, 28 Feb 2023 21:29:19 +0000 (22:29 +0100)]
serial: sh: Add HSCIF support for R-Car SoC
Provide the basic HSCIF support for R-Car SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Fill in HSSRR offset for Gen2 and SCBRR calculation for Gen2 and Gen3] Reviewed-by: Simon Glass <sjg@chromium.org>
Hai Pham [Tue, 28 Feb 2023 21:29:18 +0000 (22:29 +0100)]
serial: sh: Add R-Car Gen4 support
Add R-Car Gen4 family support. The basic function is as same as previous
R-Car Generation.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Swap RZ/A1 and Gen4 to keep the GenN sequence, use RCAR_64]
Hai Pham [Fri, 7 Apr 2023 15:12:17 +0000 (17:12 +0200)]
net: ravb: Add R-Car Gen4 support
Add support for R-Car Gen4 SoCs and a matching DT compatible.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop SoC specific compatible, use RCAR_64 Kconfig symbol, update commit message]
Hai Pham [Tue, 28 Feb 2023 21:24:06 +0000 (22:24 +0100)]
mmc: renesas-sdhi: Add R-Car Gen4 support
Support R-Car Gen4 family. The default quirk is similar to previous
generation.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Use RCAR_64 Kconfig
Marek Vasut [Tue, 28 Feb 2023 21:18:13 +0000 (22:18 +0100)]
mmc: tmio: Replace ifdeffery with IS_ENABLED/CONFIG_IS_ENABLED macros
Instead of #if and #ifdef, use IS_ENABLED and CONFIG_IS_ENABLED macros.
This improves build test coverage. The CONFIG_SPL_BUILD must remain an
ifdef, as CONFIG_SPL_STACK may not always be defined, e.g. in U-Boot
proper build. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Marek Vasut [Tue, 28 Feb 2023 21:18:12 +0000 (22:18 +0100)]
mmc: tmio: Check 'addr' width before checking for 64bit limitation
The 64bit limitation check is compiled and optimized out on 32bit
platforms, but generates a type width warning:
drivers/mmc/tmio-common.c: In function ‘tmio_sd_addr_is_dmaable’:
drivers/mmc/tmio-common.c:376:26: warning: right shift count >= width of type [-Wshift-count-overflow]
376 | if (addr >> 32)
| ^~
Fix the warning by checking the addr type width to see whether the
shift even makes sense in the first place. The width check is also
optimized out at compile time.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Hai Pham [Tue, 28 Feb 2023 21:25:51 +0000 (22:25 +0100)]
i2c: rcar_i2c: Add R-Car Gen4 support
Add support for R-Car Gen4 SoCs into the driver.
While I2C on R-Car Gen4 does support some extra features (Slave Clock
Stretch Select), for now it is treated the same as I2C on R-Car Gen3,
which let us share the same driver.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Use RCAR_64 Kconfig Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Fri, 7 Apr 2023 14:44:19 +0000 (10:44 -0400)]
Merge branch '2023-04-06-assorted-updates'
- Make use of the semi-formal "fallthrough" mechanism, update env tools
to use /run for lockfile, add 2048 game (as a way to test console
changes), update some CONFIG option logic in Kconfig, have lmb command
show regions in use, remove some duplicate serial code, add
__gnu_thumb1_case_si code and fix m68k custodian email address.
Hai Pham [Tue, 28 Feb 2023 21:23:07 +0000 (22:23 +0100)]
gpio: renesas: Add R-Car Gen4 support
Add support for the GPIO controller block in the R-Car Gen4 family.
It has a General Input Enable Register (INEN), whose reset state is to
have all inputs disabled.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: - Enable DTO support by default
- Sort the Kconfig lists
- Select RCAR_64 Kconfig option to pull in all the shared
Kconfig options with Gen3, and use where applicable to
deduplicate entries.
- Fix reference [2] typo in commit message
- Drop config options moved to Kconfig, rename rest to CFG_
accordingly to synchronize with upstream changes. Drop
removed CONFIG_VERY_BIG_RAM.
- Move board size limit to arch/Kconfig
- Move GICR_BASE to headers instead of common config]
Marek Vasut [Sun, 19 Mar 2023 17:09:42 +0000 (18:09 +0100)]
phy: Add .set_mode and .set_speed callbacks
Add two new callbacks matching the Linux ones. The .set_mode is used to set
PHY mode and submode, where mode is either USB, Ethernet, and so on, while
submode is e.g. for Ethernet case RGMII, RMII, and so on. The .set_speed is
used to configure link speed into the PHY. Unlike the existing configure
callback, which is used to pass arbitrary custom information to the PHY,
these two callbacks are used to pass standardized set of information to
the PHY.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Sun, 19 Mar 2023 17:08:10 +0000 (18:08 +0100)]
net: phy: marvell10g: Adapt Marvell 10G PHY driver from Linux
Pull Marvell 10G PHY driver from Linux 6.1.y as of commit d6d29292640d3 ("net: phy: marvell10g: select host interface configuration")
and heavily adapt to match U-Boot PHY framework. Support for
hwmon is removed as is much other functionality which could
not be tested, this results in much simpler driver which can
only bring the PHY up and set MAC type.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Sun, 19 Mar 2023 17:08:09 +0000 (18:08 +0100)]
net: phy: Add MDIO PCS 2.5G and 5G speed macros from Linux
Add MDIO PCS 2.5G and 5G speed macros from Linux 5.1.y as of commit 7fd8afa8933a0 ("net: phy: Add generic support for 2.5GBaseT and 5GBaseT")
This is used by the upcoming Marvell 10G PHY driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Sun, 19 Mar 2023 17:08:08 +0000 (18:08 +0100)]
net: phy: Add phy_read_mmd_poll_timeout() from Linux
Add phy_read_mmd_poll_timeout() from Linux 5.7.y as of commit bd971ff0b7392 ("net: phy: introduce phy_read_mmd_poll_timeout macro")
This is used by the upcoming Marvell 10G PHY driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Sun, 19 Mar 2023 17:08:07 +0000 (18:08 +0100)]
net: phy: Add phy_modify_mmd() and phy_modify_mmd_changed() from Linux
Add phy_modify_mmd()/phy_modify_mmd_changed() from Linux 5.1.y as of commit b8554d4f7288f ("net: phy: add register modifying helpers returning 1 on change")
This is used by the upcoming Marvell 10G PHY driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Sun, 19 Mar 2023 17:08:06 +0000 (18:08 +0100)]
net: phy: marvell: Import and use marvell_phy.h from Linux
Import marvell_phy.h from Linux 5.14.y as of commit a5de4be0aaaa6 ("net: phy: marvell10g: fix differentiation of 88X3310 from 88X3340")
and use it in marvell PHY driver instead of current ad-hoc macros.
Two of the PHY IDs are unknown to Linux, 88E1149S and 88E1680, for
those two, only sync the length of the hexadecimal number to 8 digits.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Tue, 21 Mar 2023 17:25:54 +0000 (18:25 +0100)]
net: phy: Synchronize PHY interface modes with Linux
Synchronize PHY interface modes with Linux next 6.2.y commit: 0194b64578e90 ("net: phy: improve phy_read_poll_timeout")
Retain LX2160A/LX2162A PHY modes as those are not yet supported
by the Linux kernel, but isolate those with ifdeffery.
Isolate NCSI which are also not supported by Linux kernel. Note
that the ifdeffery cannot be avoided with IS_ENABLED() here due
to compilation of the entire conditional, which would fail in
case NCSI symbols are not available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Tue, 21 Mar 2023 17:25:53 +0000 (18:25 +0100)]
net: mvpp2: Replace PHY_INTERFACE_MODE_SFI with 5GBASER/10GBASER/XAUI
Replace PHY_INTERFACE_MODE_SFI with PHY_INTERFACE_MODE_5GBASER,
PHY_INTERFACE_MODE_10GBASER and PHY_INTERFACE_MODE_XAUI to match
Linux PHY interface modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Tue, 21 Mar 2023 17:25:52 +0000 (18:25 +0100)]
net: mvpp2: Drop PHY_INTERFACE_MODE_SGMII_2500 support
This mode does not seem to be well defined and used anywhere, remove support for it.
Based on discussion:
- 1000baseX does c37 AN of duplex+pause
- SGMII does AN of duplex+pause+speed, at lower speed bytes are repeated 10x/100x
- 2500baseX does not do AN, or does very different c73 AN
- SGMII 2500 behavior is unclear
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Marek Vasut [Sun, 19 Mar 2023 17:03:17 +0000 (18:03 +0100)]
net: phy: Only call phy_init() on systems needing manual relocation
The phy_init() is now used only to perform manual relocation of PHY
driver callbacks. Wrap it in ifdeffery and only call it on systems
which still require manual relocation, i.e. m68k .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Michal Simek <michal.simek@amd.com> Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
Marek Vasut [Sun, 19 Mar 2023 17:03:16 +0000 (18:03 +0100)]
net: phy: Re-inline phy_drv_reloc()
Wrap phy_drv_reloc() back into phy_init() to reduce ifdeffery,
since phy_drv_reloc() is now called only from one call site.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Michal Simek <michal.simek@amd.com> Tested-by: Michal Simek <michal.simek@amd.com> #microblaze (MANUAL_RELOC)
projects / u-boot.git / log