Heiko Stuebner [Thu, 18 Jun 2020 14:23:25 +0000 (16:23 +0200)]
lib: rsa: free local arrays after use in rsa_gen_key_prop()
n, rr and rrtmp are used for internal calculations, but in the end
the results are copied into separately allocated elements of the
actual key_prop, so the n, rr and rrtmp elements are not used anymore
when returning from the function and should of course be freed.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
lib: rsa: fix allocated size for rr and rrtmp in rsa_gen_key_prop()
When calculating rrtmp/rr rsa_gen_key_prop() tries to make
(((rlen + 31) >> 5) + 1) steps in the rr uint32_t array and
(((rlen + 7) >> 3) + 1) / 4 steps in uint32_t rrtmp[]
with rlen being num_bits * 2
On a 4096bit key this comes down to to 257 uint32_t elements
in rr and 256 elements in rrtmp but with the current allocation
rr and rrtmp only have 129 uint32_t elements.
On 2048bit keys this works by chance as the defined max_rsa_size=4096
allocates a suitable number of elements, but with an actual 4096bit key
this results in other memory parts getting overwritten.
So as suggested by Heinrich Schuchardt just use the actual bit-size
of the key as base for the size calculation, in turn making the code
compatible to any future keysizes.
Heiko Stuebner [Thu, 18 Jun 2020 14:23:23 +0000 (16:23 +0200)]
lib: rsa: bring exp_len in line when generating a key_prop
The exponent field of struct key_prop gets allocated an uint64_t,
and the contents are positioned from the back, so an exponent of
"0x01 0x00 0x01" becomes 0x0 0x0 0x0 0x0 0x0 0x1 0x0 0x1"
Right now rsa_gen_key_prop() allocates a uint64_t but sets exp_len
to the size returned from the parser, while on the other hand the
when getting the key from the devicetree exp_len always gets set to
sizeof(uint64_t).
So bring that in line with the established code.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Heiko Stuebner [Thu, 18 Jun 2020 14:23:21 +0000 (16:23 +0200)]
lib: rsa: distinguish between tpl and spl for CONFIG_RSA_VERIFY
While the SPL may want to do signature checking this won't be
the case for TPL in all cases, as TPL is mostly used when the
amount of initial memory is not enough for a full SPL.
So on a system where SPL uses DM but TPL does not we currently
end up with a TPL compile error of:
lib/rsa/rsa-verify.c:48:25: error: dereferencing pointer to incomplete type ‘struct checksum_algo’
To prevent that change the $(SPL_) to $(SPL_TPL_) to distinguish
between both. If someone really needs FIT signature checking in
TPL as well, a new TPL_RSA_VERIFY config symbol needs to be added.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Heiko Stuebner [Mon, 29 Jun 2020 23:05:45 +0000 (01:05 +0200)]
cmd: add a panic command
Even in boot scripts it may be needed to "panic" when all options
are exhausted and the device specification specifies hanging
instead of resetting the board.
So add a new panic command that just wraps around the core panic
call in U-Boot and can take an optional message.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Stefan Roese [Fri, 15 May 2020 05:09:03 +0000 (07:09 +0200)]
debug_uart: Add CR before and after announce string
Add linefeeds before and after the announce string. This makes the
output easier to read, especially if some text follows the announce
message without a specific additional CR.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Johannes Holland [Mon, 11 May 2020 13:22:25 +0000 (15:22 +0200)]
tpm: add #ifndef to fix redeclaration build errors
tpm_tis_spi.c directly includes tpm_tis.h and tpm-v2.h which both
define the same enums (see e.g. TPM_ACCESS_VALID). Add an #ifndef to
prevent redeclaration errors.
Signed-off-by: Johannes Holland <johannes.holland@infineon.com>
Bruno Thomsen [Fri, 12 Jun 2020 15:17:33 +0000 (17:17 +0200)]
tpm2: tis_spi: add linux compatible fallback string
This solves a compatibility issue with Linux device trees
that contain TPMv2.x hardware. So it's easier to import DTS
from upstream kernel when migrating board init from C code
to DTS.
The issue is that fallback binding is different between Linux
and u-Boot.
Linux: "tcg,tpm_tis-spi"
U-Boot: "tis,tpm2-spi"
As there are currently no in-tree users of the U-Boot binding,
it makes sense to use Linux fallback binding.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
The PHY needs a reset in order to be functionnal for U-Boot, add the old
PHY reset bindings for dwmac until we support the new bindings in the PHY node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Anand Moon <linux.amoon@gmail.com>
Andre Przywara [Thu, 11 Jun 2020 11:03:20 +0000 (12:03 +0100)]
arm: juno: Enable PCI
The ARM Juno boards in their -r1 and -r2 variants sport a PCIe
controller, which we configure already in board specific code to be ECAM
compliant. Hence we can just enable the generic ECAM driver to let
U-Boot use PCIe devices.
Add the respective options to the Juno defconfig to enable the PCI
framework and the generic ECAM driver, and initialise the driver upon
loading U-Boot.
Make some functions in the Juno PCIe init code static on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Andre Przywara [Thu, 11 Jun 2020 11:03:18 +0000 (12:03 +0100)]
arm: juno: Enable DM_ETH
The smc911X driver is now DM enabled, so we can switch the Juno board
over to use DM_ETH for the on-board Fast Ethernet device.
Works out of the box by using the DT.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Andre Przywara [Thu, 11 Jun 2020 11:03:17 +0000 (12:03 +0100)]
net: smc911x: Properly handle EEPROM MAC address
When compiled as a DM_ETH driver, the scm911x driver was reading the MAC
address from the optional EEPROM storage, but failed to copy this to the
platdata struct. Since it was also missing a definition of the
read_rom_hwaddr() function, the generic Ethernet code was dismissing
this MAC address, falling back to a random address or denying to start
at all.
Add an implementation of .read_rom_hwaddr, and refactor the function
reading the ROM address to be called by all interested parties.
This fixes MAC address issues when using the driver in DM_ETH "mode".
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-By: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Andre Przywara [Thu, 11 Jun 2020 11:03:16 +0000 (12:03 +0100)]
net: dm: Remove warning about EEPROM provided MAC address
Similar to patch 821fec0ceb3e ("net: remove scary warning about EEPROM
provided MAC address") this removes the somewhat awkward "warning" on
boards using DM_ETH:
In many parts of the computing world having a unique MAC address
sitting in some on-NIC storage is considered the normal case.
If there is a properly provided MAC address (either from ROM or from DT),
remove the warning to not scare the user unnecessarily.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-By: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Andre Przywara [Thu, 11 Jun 2020 11:03:15 +0000 (12:03 +0100)]
arm: vexpress64: Fix counter frequency
The arch timer on 64-bit Arm Ltd. platforms is driven by a 24 MHz
crystal oscillator, so the frequency is not 25165824 MHz, as the current
code suggests.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
On ARM systems gd is stored in register r9 or x18. When compiling with
clang gd is defined as a macro calling function gd_ptr(). So we can not
make assignments to gd.
Use function set_gd() for setting the register on ARM.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Heiko Schocher [Fri, 22 May 2020 09:08:59 +0000 (11:08 +0200)]
gpio: search for gpio label if gpio is not found through bank name
dm_gpio_lookup_name() searches for a gpio through
the bank name. But we have also gpio labels, and it
makes sense to search for a gpio also in the labels
we have defined, if no gpio is found through the
bank name definition.
This is useful for example if you have a wp pin on
different gpios on different board versions.
If dm_gpio_lookup_name() searches also for the gpio labels,
you can give the gpio an unique label name and search
for this label, and do not need to differ between
board revisions.
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Don't enable by default] Signed-off-by: Tom Rini <trini@konsulko.com>
net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings
RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.
This commits lets proper packets to be transmitted over the network.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
net: phy: realtek: Add support for RTL8201F PHY module.
This patch adds support for Realtek PHY RTL8201F 10/100Mbs
(with variants: RTL8201FN and RTL8201FL) PHYceiver. It is
present on Actions Semi Cubieboard7 board.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Calculate the SDRAM size from DDR capacity register registers instead
of using hard-coded value. This is quite useful to get correct size
on differnt boards based on Actions OWL family of SoCs (S700 and S900).
There is no documentation available that talks about DDR registers, and
this is very much taken from vendor source.
This commit lets Linux boot on Cubieboard7-lite(based on S700).
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Niel Fourie [Mon, 30 Mar 2020 15:22:58 +0000 (17:22 +0200)]
cmd: blkls: Add blkls command
Add a command to print a list of available block device drivers,
and for each, the list of known block devices.
Signed-off-by: Niel Fourie <lusus@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
Renamed dm "drivers" subcommand to "compat" (as it listed
compatibility strings) and prevent it from segfaulting when
drivers have no of_match populated.
Added a new "drivers" subcommand to dump a list of all known DM
drivers and for each, their uclass id, uclass driver and names of
attached devices.
Added a new "static" subcommand to dump a list of DM drivers with
statically defined platform data.
Signed-off-by: Niel Fourie <lusus@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Niel Fourie [Tue, 24 Mar 2020 15:17:04 +0000 (16:17 +0100)]
cmd: fs: Add command to list supported fs types
Added command "fstypes" to list supported/included filesystems.
Signed-off-by: Niel Fourie <lusus@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Limit to sandbox] Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 7 Jul 2020 18:00:44 +0000 (14:00 -0400)]
Merge tag 'u-boot-stm32-20200707' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- arch and board update for stm32mp15:
- use OPP information in device tree for 800MHz/650MHz support
- ram: inprovments of test command
- solve boot on closed chip when access to DBGMCU_IDC is protected
- stm32prog command: Add "device anme" during USB enumeration
- update configs: activate WATCHDOG and 'env erase' command,
increase teed partition, support SD card after NOR boot by default and
use env info in env_check
- some sboard cleanups: gpio hog in dh board, specific driver for
type-c stusb1600 controller code in a driver move part of code in spl.c
and in common directory
- fix STM32 compatible for dwc_eth_qos driver
- support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx
drivers
- vrefbuf: fix a possible overshoot when re-enabling
ARM Architecture reference manual clearly states that PE pipeline
should be flushed after changes to some system registers. Refer to
paragraph "B2.3.5 Memory Barriers" at page B2-92 of "Arm Architecture
Reference Manual ARMv8 for ARMv8-A Architecture Profile" (ARM DDI
0487B.a).
Failing to issue instruction synchronization barrier can lead to
spurious errors, like synchronous exception when accessing FPU
registers. This is very prominent on CPUs with long instruction
pipeline, like ARM Cortex A72.
ram: stm32mp1: add size and addr parameter to test all
Add size and addr parameter to test "All" to override the default
value (4kB and STM32_DDR_BASE) used in tests with these optional
parameters: [size] or [addr].
When other optional parameters are present before [addr],
they are replaced by default value:
- [loop] = "1"
- [pattern] = "-" (new: force default pattern)
Example to use:
DDR>test 0 1 0x20000
DDR>test 0 1 0x1000000 0xD0000000
Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
ram: stm32mp1: use the DDR size by default in the test addressBus
The test 4 = "AddressBus [size] [addr]" without parameter
detects alias for any address bit only when:
- size = real size of DDR
- addr = start of DDR = 0xC0000000
These value must be the default value when parameters are absent.
This patch sets bufsize to STM32_DDR_SIZE and get_bufsize() selects
the correct value for bufsize when this parameter is absent =
full size of the DDDR
On EV1 board :
DDR> test 4
running at 0xC0000000 length 0x40000000
On DK2 board
DDR> test 4
running at 0xC0000000 length 0x20000000
Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
ram: stm32mp1: protect minimum value in get_bufsize
Add protection on minimum value for result of get_bufsize
and check the alignment of buffer size: only multiple min_size
is allowed; only 4 bytes alignment was checked previously
(value & 0x3).
For example the "Random" test raises an issue when size is not 8 bytes
aligned because address for buffer = address + size / 2 is not word
aligned.
This patch avoid test error for unsupported size value.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the define ENV_IS_IN_DEVICE to test if one the
CONFIG_ENV_IS_IN_... is defined and correct the detection of
persistent storage support in the command "env info"
if CONFIG_ENV_IS_NOWHERE is activated.
Since commit 60d5ed2593c9 ("env: allow ENV_IS_NOWHERE with
other storage target") test CONFIG_ENV_IS_NOWHERE is not
enough; see also commit 953db29a1e9c6 ("env: enable saveenv
command when one CONFIG_ENV_IS_IN is activated").
This patch avoids issue for this command in stm32mp1 platform.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Mon, 29 Jun 2020 08:34:06 +0000 (10:34 +0200)]
board: st: move type-c stusb1600 controller code in a driver
Migrate the ST Microelectronics STUSB160X Type-C controller code in
a generic I2C driver in st/common, based on Linux one in :
drivers/usb/typec/stusb160x.c
This patch simplifies the stm32mp1 board code and allows to reuse
this STUSB160X driver in other boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Tue, 16 Jun 2020 16:27:44 +0000 (18:27 +0200)]
arm: stm32mp: protect DBGMCU_IDC access with BSEC
As debugger must be totally closed on Sec closed chip,
the DBGMCU_IDC register is no more accessible (self
hosted debug is disabled with OTP).
This patch adds a function bsec_dbgswenable() to check
if the DBGMCU registers are available before to access them:
BSEC_DENABLE.DBGSWENABLE = self hosted debug status.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Tue, 16 Jun 2020 16:25:14 +0000 (18:25 +0200)]
arm: stm32mp: stm32prog: add "Device Name" in iproduct during DFU USB enumeration
Add "Device Name" in iproduct during DFU USB enumeration
to have this information in STM32CubeProgrammer trace
(this tools is compatible with @Name since v2.3)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Fabrice Gasnier [Fri, 12 Jun 2020 08:40:58 +0000 (10:40 +0200)]
power: regulator: stm32: vrefbuf: fix a possible overshoot when re-enabling
There maybe an overshoot:
- when disabling, then re-enabling vrefbuf too quickly
- or upon platform reset as external capacitor maybe slow
discharging (VREFBUF is HiZ at reset by default).
VREFBUF is used by ADC/DAC on some boards. An overshoot on the reference
voltage make the conversions inaccurate for a short period of time. So:
- Don't put the VREFBUF in HiZ when disabling, to force an active
discharge.
- Enforce a 1ms OFF/ON delay, also upon reset
Penalty is a 1ms delay is applied (even for a cold boot), when enabling
VREFBUF.
Fixes: 93cf0ae7758d ("power: regulator: Add support for stm32-vrefbuf") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Patrick Delaunay [Thu, 11 Jun 2020 14:51:17 +0000 (16:51 +0200)]
configs: stm32mp1: activate WATCHDOG
As kernel v5.6 have a solution since so we will be able to enable
the watchdog at boot time. It is reloaded by the watchdog
framework (if CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is set) and
until the userspace watchdog daemon takes over control.
Need presence of kernel patch 85fdc63fe256 ("drivers: watchdog:
stm32_iwdg: set WDOG_HW_RUNNING at probe") integrated in v5.6-rc1.
This patch revert the previous commit ca351e705a5c ("stm32mp1:
deactivate WATCHDOG in defconfig").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
pinctrl: stm32: add information on pin configuration
Add information on pin configuration used for pinmux command:
- bias configuration for output (disable, pull up, pull down)
- otype for input (open drain or push pull)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
gpio: stmfx: move function to prepare new ops introduction
Move the functions stmfx_pinctrl_set_pupd and stmfx_pinctrl_set_type;
they can be used by the new ops get_dir_flags and set_dir_flags introduced
by next patch.
No functional change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Mon, 25 May 2020 10:19:49 +0000 (12:19 +0200)]
board: stm32mp1: move the function board_debug_uart_init in spl.c
Move the debug function board_debug_uart_init in spl.c
as the debug_uart_init() function is called in arch_cpu_init()
only for SPL and remove the board.c file.
For TFABOOT, the UART TX pin configuration is done in TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Mon, 25 May 2020 10:19:48 +0000 (12:19 +0200)]
ARM: dts: stm32mp1: use OPP information for PLL1 settings in SPL
This patch allows to switch the CPU frequency to 800MHz on the
ST Microelectronics board (DK1/DK2 and EV1) or dh electronics SOM
using the STM32MP15x SOC and when it is supported by the HW
(for STM32MP15xD and STM32MP15xF).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Mon, 25 May 2020 10:19:47 +0000 (12:19 +0200)]
board: stm32mp1: update vddcore in SPL
For board using STPMIC1, the vddcore is provided by BUCK1 of STPMIC1
and need to be updated for 800MHz support and only after the clock
tree initialization.
The VDDCORE voltage value is provided by clock driver, saved in global
variable opp_voltage_mv and udpated in SPL board_early_init_f(),
just after clock tree initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Mon, 25 May 2020 10:19:46 +0000 (12:19 +0200)]
board: st: stpmic1: add function stpmic1_init
Add a function stmpic_init to early initialize the PMIC STPMIC1
- keep vdd on during the reset cycle (to avoid issue when backup battery
is absent)
- Check if debug is enabled to program PMIC according to the bit
This patch allows to remove the compilation of spl.c file from stm32mp1
board in dh_stm32mp1.
CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier
in SPL, in the function board_early_init_f.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Mon, 25 May 2020 10:19:42 +0000 (12:19 +0200)]
ARM: dts: stm32: add cpufreq support on stm32mp15x
This commit adds cpufreq support on stm32mp15x SOC. STM32 cpufreq uses
operating points V2 bindings (no legacy). Nvmem cells have to be used to
know the chip version and then which OPPs are available. Note that STM32
cpufreq driver is mainly based on "cpufreq-dt" driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Thu, 14 May 2020 13:00:23 +0000 (15:00 +0200)]
net: dwc_eth_qos: update the compatible supported for STM32
Update the compatible associated with the STM32 MPU glue
in the DWC ethernet driver.
The supported compatible is the specific "st,stm32mp1-dwmac"
as indicated in Linux binding
Documentation/devicetree/bindings/net/stm32-dwmac.txt
and not the "snps,dwmac-4.20a" only used to the select IP
version.
This glue is implemented in Linux kernel in:
drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
For information in stm32mp151.dtsi, the 2 compatibles are
supported:
According to the FAT specification it is valid to have files with an
attribute value of 0x0. This fixes a regression where different U-Boot
versions are showing different amount of files on the same storage
device. With this change U-Boot shows the same number of files and folders
as Linux and Windows.
common/board_f: Respect original FDT size while relocating
While relocating FDT we reserve some memory for the new FDT and
set the size of the FDT with that respect. But FDT may be placed
at the end of the RAM leading to memory access beyond it.
Fix this by copying exact FDT size bytes, not the reserved size.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Radxa dalang carrier boards are used to mount vmarc SoM's
of rk3399pro and rk3288 to make complete SBC.
Among these combinations, card detection gpio, max-frequency
properties are used with rk3399pro SoM but not required for
rk3288 SoM based on the hardware schematics.
So, let's move these sdmmc specific properties on associate
vmarc dtsi to make common use of dalang carrier device tree file.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
SPL_ATF_NO_PLATFORM_PARAM is selected by default for RK3399 configs, to
guard against issues when used with TF-A versions that perform
insufficient validation on the platform parameter. However, since commit 8109f738ffa7 "rockchip: increase FDT buffer size" in TF-A, passing a
device tree as platform parameter no longer causes problems for upstream
TF-A for RK3399.
Since SPL_ATF_NO_PLATFORM_PARAM doesn't need to be selected when using
upstream TF-A, change the Kconfig option from select to imply. It'll
still default to being selected but can be deselected by a user if they
know they will be using a compatible version of TF-A.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Walter Lozano <walter.lozano@collabora.com>
Jagan Teki [Wed, 10 Jun 2020 10:36:58 +0000 (16:06 +0530)]
arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support
Rock Pi N10 is a Rockchip RK3399Pro based SBC, which has
- VMARC RK3399Pro SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3399Pro SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N10 SBC.
So, add initial support for Rock Pi N10 by including rk3399,
rk3399pro vamrc-som and raxda dalang carrier board dtsi files.
rk3399pro-rock-pi-n10.dts was synced from linux-next v5.7-rc1.
Tested
- ROCK PI N10 Model B
- ROCK PI N10 Model C
- Boot from SD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Carrier board often referred as baseboard. For making
complete SBC or any other industrial boards, these
carrier boards will be used with associated SOMs.
Radxa has Dalang carrier board which supports on-board
peripherals, ports like USB-2.0, USB-3.0, HDMI, MIPI DSI/CSI,
eDP, Ethernet, WiFi, PCIe, USB-C, 40-Pin GPIO header and etc.
Right now Dalang carrier board is used with two SBC-variants:
Rock Pi N10 => VMARC RK3399Por SOM + Dalang carrier board
Rock Pi N8 => VMARC RK3288 SOM + Dalang carrier board(+codec)
So add this carrier board dtsi as a separate file in
ARM directory, so-that the same can reuse it in both
rk3288, rk3399pro variants of Rockchip SOMs.
Sync this dtsi from linux-next v5.7-rc1.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Peter Robinson [Mon, 8 Jun 2020 22:50:30 +0000 (23:50 +0100)]
rockchip: Pinebook Pro: Fix SPI flash and store env on it
Some minor fixes for SPI flash on the Pinebook Pro and also
default to saving environment to the SPI flash as it's
guaranteed to be on board.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(applied with make savedefconfig) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
With video output enabled and USB keyboard supported there is no need
for serial console. So let initialize USB subsystem so keyboard connected to
board (either directly or via hub) can be used to interrupt autoboot.
U-Boot TPL 2020.07-rc3-00123-g52d6cbd1a7 (Jun 03 2020 - 17:34:20)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
256B stride
256B stride
lpddr4_set_rate: change freq to 400000000 mhz 0, 1
lpddr4_set_rate: change freq to 800000000 mhz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...
SoC: Rockchip rk3399
Reset cause: RST
Model: Pine64 RockPro64 v2.1
DRAM: 3.9 GiB
PMIC: RK808
MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
OK
In: serial
Out: vidconsole
Err: vidconsole
Model: Pine64 RockPro64 v2.1
Net: eth0: ethernet@fe300000
starting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: USB EHCI 1.00
Bus usb@fe3e0000: USB OHCI 1.0
Bus dwc3: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3e0000 for devices... 2 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
=>
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
As part of merging the next branch in to master, the sifive_fu540 will
fail to link:
riscv64-linux-ld.bfd: lib/built-in.o: in function `panic_finish':
lib/panic.c:28: undefined reference to `do_reset'
make[2]: *** [spl/u-boot-spl] Error 1
make[1]: *** [spl/u-boot-spl] Error 2
make: *** [sub-make] Error 2
And while the "fix the build" option of enabling CONFIG_SPL_SYSRESET may
solve the issue, it is unclear that it is the correct path exactly. For
the moment, I am reverting this commit and take a "revert the revert"
and proper fix as soon as it's available.
video: restore CONFIG_VIDCONSOLE_AS_LCD as boolean
This patch restores CONFIG_VIDCONSOLE_AS_LCD as boolean
and introduce a separate sting as CONFIG_VIDCONSOLE_AS_NAME
to search this string in stdout used as videoconsole.
This patch avoid issue with board defconfig or code expecting
CONFIG_VIDCONSOLE_AS_LCD as boolean.
Fixes: 22b897a12323 ("video: extend stdout video console work-around for 'vga'") Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
projects / u-boot.git / log