Quentin Schulz [Thu, 23 May 2024 16:59:35 +0000 (18:59 +0200)]
rockchip: Use common bss and stack addresses on PX30
See commit
008ba0d56d00 ("rockchip: Add common default bss and stack
addresses") for memory layout. This migrates PX30 to use the new layout,
except for TPL. Indeed, PX30 is extremely limited in SRAM, so we need to
be extra careful about what goes into the TPL and how much we can
allocate there, so let's keep the current value for
TPL_SYS_MALLOC_F_LEN (already present in the PX30-specific Kconfig, from
an earlier commit).
This will allow us to use the same memory layout on one more Rockchip
SoC, which is always a nice thing. Additionally, this will make it
easier to fix U-Boot proper pre-reloc running out of memory on PX30 in a
subsequent commit.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Quentin Schulz [Thu, 23 May 2024 16:59:34 +0000 (18:59 +0200)]
rockchip: px30: default TPL_SYS_MALLOC_F_LEN to 0x600 on PX30 Kconfig level
This is the kind of setting that typically doesn't need to be changed
between boards based on the same SoC, so let's make it the default in
PX30 Kconfig so we don't have to care about it in the defconfig if we
don't want to.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Heiko Stuebner [Wed, 22 May 2024 17:31:29 +0000 (19:31 +0200)]
clk: rockchip: rk3588: Set SPLL frequency during SPL stage
All parts expect the SPLL to run at 702MHz. In U-Boot it's the SPLL_HZ
declaring this rate and in the kernel it's a fixed clock definition.
While everything is expecting 702MHz, the SPLL is not running that
frequency when coming from the bootrom though, instead it's running
at 351MHz and the vendor-u-boot just sets it to the expected frequency.
The SPLL itself is located inside the secure-BUSCRU and in theory
accessible as an SCMI clock, though this requires an unknown amount
of cooperation from trusted-firmware to set at a later stage, though
during the SPL stage we can still access the relevant CRU directly.
The SPLL is for example necessary for the DSI controllers to produce
output.
As the SPLL is "just" another rk3588 pll, just set the desired rate
directly during the SPL stage.
Tested on rk3588-rock5b and rk3588-tiger by reading back the PLL rate
and also observing working DSI output with this change.
Fixes: 6737771600d4 ("rockchip: rk3588: Add support for sdmmc clocks in SPL")
Suggested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Anand Moon [Tue, 14 May 2024 04:05:22 +0000 (09:35 +0530)]
rockchip: rv1126: Migrate to OF_UPSTREAM
Migrate RV1126 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is migrated to use OF_UPSTREAM:
- rv1126-edgeble-neu2 : Board is an industrial form factor
IO board.
- sonoff-ihost-rv1126 : Gateway device designed to provide a
Smart Home Hub.
Cc: Tim Lunn <tim@feathertop.org>
Cc: Jagan Teki <jagan@edgeble.ai>
Reviewed-By: Tim Lunn <tim@feathertop.org>
Tested-By: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <anand@edgeble.ai>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Fabio Estevam [Thu, 9 May 2024 16:42:25 +0000 (13:42 -0300)]
rockchip: rv1108: Remove unneeded local rv1108-cru.h
After the conversion of RV1108 to OF_UPSTREAM,
include/dt-bindings/clock/rv1108-cru.h is no longer needed because
there is dts/upstream/include/dt-bindings/clock/rv1108-cru.h from
upstream Linux.
Remove the unneeded rv1108-cru.h file.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini [Mon, 20 May 2024 16:05:16 +0000 (10:05 -0600)]
Prepare v2024.07-rc3
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sun, 19 May 2024 02:20:43 +0000 (20:20 -0600)]
Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit
c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to
2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Fiona Klute [Wed, 1 May 2024 08:54:09 +0000 (10:54 +0200)]
Init virtio before loading ENV from EXT4 or FAT
Specifying a file in an EXT4 or FAT partition on a virtio device as
environment location failed because virtio hadn't been initialized by
the time the environment was loaded. This patch mirrors commit
54ee5ae84191 ("Add SCSI scan for ENV in EXT4 or FAT") in issue and
fix, just for a different kind of block device.
The additional include in include/virtio.h is needed so all functions
called there are defined, the alternative would have been to include
dm/device.h separately in the env/ sources.
Checkpatch suggests using "if (IS_ENABLED(CONFIG...))" instead of
"#if defined(CONFIG_...)", I'm sticking to the style of the existing
code here.
Signed-off-by: Fiona Klute <fiona.klute@gmx.de>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Bin Meng <bmeng.cn@gmail.com>
CC: Rogier Stam <rogier@unrailed.org>
Tom Rini [Thu, 16 May 2024 15:52:24 +0000 (09:52 -0600)]
Merge tag 'u-boot-dfu-
20240516' of https://source.denx.de/u-boot/custodians/u-boot-dfu
u-boot-dfu-
20240516
- Fix cdns3 low power hang via fast access bit
- Multiple dwc3 gadget fixes, mainly for USB support on TI AM6232
- Consistent USB_GADGET_MANUFACTURER for PHYTEC boards
- MAINTAINERS file update for u-boot-dfu
Mattijs Korpershoek [Thu, 16 May 2024 09:15:42 +0000 (11:15 +0200)]
MAINTAINERS: add USB gadget regex to u-boot-dfu tree
We try to split work with Marek on USB as following:
- Mattijs handles USB gadget
- Marek handles the rest of USB
Add additional gadget patterns to the maintainers file so that I
get cc'ed more often on USB gadget patches.
Acked-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240516-gadget-maintainer-v2-2-23cc916df434@baylibre.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Mattijs Korpershoek [Thu, 16 May 2024 09:15:41 +0000 (11:15 +0200)]
MAINTAINERS: add tree link for fastboot
Fastboot patches go through the u-boot-dfu tree.
Add a link in the maintainers file for it.
Link: https://lore.kernel.org/r/20240516-gadget-maintainer-v2-1-23cc916df434@baylibre.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Thinh Nguyen [Fri, 12 Apr 2024 20:26:06 +0000 (22:26 +0200)]
usb: dwc3: gadget: Disable GUSB2PHYCFG.SUSPHY for End Transfer
Upstream Linux commit
3aa07f72894d.
If there's a disconnection while operating in eSS, there may be a delay
in VBUS drop response from the connector. In that case, the internal
link state may drop to operate in usb2 speed while the controller thinks
the VBUS is still high. The driver must make sure to disable
GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed.
The End Transfer command may be called, and only that command needs to
go through at this point. Let's keep it simple and unconditionally
disable GUSB2PHYCFG.SUSPHY whenever we issue the command.
This scenario is not seen in real hardware. In a rare case, our
prototype type-c controller/interface may have a slow response
triggerring this issue.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5651117207803c26e2f22ddf4e5ce9e865dcf7c7.1668045468.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240412202611.3565052-7-alexander.sverdlin@siemens.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Felipe Balbi [Fri, 12 Apr 2024 20:26:05 +0000 (22:26 +0200)]
usb: dwc3: gadget: properly check ep cmd
Upstream Linux commit
5999914f227b.
The cmd argument we pass to
dwc3_send_gadget_ep_cmd() could contain extra
arguments embedded. When checking for StartTransfer
command, we need to make sure to match only lower 4
bits which contain the actual command and ignore the
rest.
Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[A. Sverdlin: cherry-picked only DWC3_DEPCMD_CMD() define]
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240412202611.3565052-6-alexander.sverdlin@siemens.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Thinh Nguyen [Fri, 12 Apr 2024 20:26:04 +0000 (22:26 +0200)]
usb: dwc3: gadget: Check ENBLSLPM before sending ep command
Upstream Linux commit
87dd96111b0b.
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.
Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.
DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240412202611.3565052-5-alexander.sverdlin@siemens.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Felipe Balbi [Fri, 12 Apr 2024 20:26:03 +0000 (22:26 +0200)]
usb: dwc3: gadget: only resume USB2 PHY in <=HIGHSPEED
Upstream Linux commit
ab2a92e7a608.
As a micro-power optimization, let's only resume the
USB2 PHY if we're working on <=HIGHSPEED. If we're
gonna work on SUPERSPEED or SUPERSPEED+, there's no
point in resuming the USB2 PHY.
Fixes: 2b0f11df84bb ("usb: dwc3: gadget: clear SUSPHY bit before ep cmds")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240412202611.3565052-4-alexander.sverdlin@siemens.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Felipe Balbi [Fri, 12 Apr 2024 20:26:02 +0000 (22:26 +0200)]
usb: dwc3: gadget: clear SUSPHY bit before ep cmds
Upstream Linux commit
2b0f11df84bb.
Synopsys Databook 2.60a has a note that if we're
sending an endpoint command we _must_ make sure that
DWC3_GUSB2PHY(n).SUSPHY bit is cleared.
This patch implements that particular detail.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240412202611.3565052-3-alexander.sverdlin@siemens.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Felipe Balbi [Fri, 12 Apr 2024 20:26:01 +0000 (22:26 +0200)]
usb: dwc3: gadget: combine return points into a single one
Upstream Linux commit
c0ca324d09a0.
dwc3_send_gadget_ep_cmd() had three return
points. That becomes a pain to track when we need to
debug something or if we need to add more code
before returning.
Let's combine all three return points into a single
one just by introducing a local 'ret' variable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240412202611.3565052-2-alexander.sverdlin@siemens.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tom Rini [Tue, 14 May 2024 13:45:49 +0000 (07:45 -0600)]
Merge https://source.denx.de/u-boot/custodians/u-boot-riscv
CI: https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/20690
- RISC-V: Add NULL check after parsing compatible string
- Board: Add Milk-V Mars CM board
- Andes: Unify naming policy
Tom Rini [Tue, 14 May 2024 13:45:14 +0000 (07:45 -0600)]
Merge branch 'qcom-main' of https://source.denx.de/u-boot/custodians/u-boot-snapdragon
This [pull request] for master fixes framebuffer video on almost all
Qualcomm platforms where the framebuffer is initialised by the first
stage bootloader.
Leo Yu-Chi Liang [Tue, 14 May 2024 09:50:11 +0000 (17:50 +0800)]
andes: Unify naming policy for Andes related source
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Heinrich Schuchardt [Tue, 14 May 2024 05:51:42 +0000 (07:51 +0200)]
riscv: simplify backtrace report
* We already have a header 'backtrace', there is no need to repeat the
word backtrace on every line.
* Add a blank line before the backtrace section of the crash report for
improved readability.
* If U-Boot is compiled without backtrace, there is no need to write a
message at all.
* Avoid #ifdef. We prefer functions to always be compiled and let
the linker remove them if not needed.
* Foresee 3 digits for the backtrace index.
For testing the 'exception' command can be used.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Heinrich Schuchardt [Sun, 12 May 2024 04:25:26 +0000 (06:25 +0200)]
starfive: add mac vendor sub-command
As boards from multiple vendors (Milk-V, StarFive, Pine64) use the mac
command provide a sub-command to set the vendor string.
Reported-by: E. Shattow <lucent@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sun, 12 May 2024 04:25:25 +0000 (06:25 +0200)]
configs: visionfive2: enable SPL_YMODEM_SUPPORT
We can use U-Boot for recovering JH7110 based boards via UART
if CONFIG_SPL_YMODEM_SUPPORT=y.
* Send u-boot-spl.normal.out via XMODEM.
* Send u-boot.itb via YMODEM.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E. Shattow <lucent@gmail.com>
Heinrich Schuchardt [Sun, 12 May 2024 04:25:24 +0000 (06:25 +0200)]
doc: Milk-V Mars CM and Milk-V Mars CM Lite
Provide a man-page describing the usage of U-Boot on
the Milk-V Mars CM and Milk-V Mars CM Lite boards.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Heinrich Schuchardt [Sun, 12 May 2024 04:25:23 +0000 (06:25 +0200)]
board: add support for Milk-V Mars CM
We already support the VisionFive 2 and the Milk-V Mars board by
patching the VisionFive 2 device tree. With this patch the same
is done for the Milk-V Mars CM.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: E. Shattow <lucent@gmail.com>
Reviewed-by: E. Shattow <lucent@gmail.com>
Heinrich Schuchardt [Sun, 12 May 2024 04:25:22 +0000 (06:25 +0200)]
board: starfive: function to read eMMC size
The EEPROM provides information about the size of the eMMC.
Provide a new function get_mmc_size_from_eeprom() to read it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E. Shattow <lucent@gmail.com>
Hanyuan Zhao [Mon, 6 May 2024 09:10:06 +0000 (17:10 +0800)]
riscv: add NULL check before calling strlen in the riscv cpu's get_desc()
Without the NULL check, if the devicetree that u-boot loads does not have a
compatible property then a store access fault will be raised and force the
machine to reset, due to the NULL pointer we passed to strlen. This commit
adds this check and will return -ENOSPC to indicate the get_desc failed.
Signed-off-by: Hanyuan Zhao <zhaohy22@mails.tsinghua.edu.cn>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Benjamin Hahn [Fri, 3 May 2024 07:00:38 +0000 (09:00 +0200)]
configs: Make USB_GADGET_MANUFACTURER consistent over all PHYTEC boards
Set CONFIG_USB_GADGET_MANUFACTURER to PHYTEC for all PHYTEC boards.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Acked-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240503-wip-bhahn-bspimx8m-3196-v1-1-855c7242151f@phytec.de
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Aswath Govindraju [Wed, 24 Apr 2024 07:39:11 +0000 (13:09 +0530)]
usb: cdns3: gadget.c: Set fast access bit
When the device port is in a low power state [U3/L2/Not Connected],
accesses to usb device registers may take a long time. This could lead to
potential core hang when the controller registers are accessed after the
port is disabled by setting DEVDS field. Setting the fast register access
bit ensures that the PHY clock is keeping up in active state.
Therefore, set fast access bit to ensure the accesses to device registers
are quick even in low power states.
commit
b5148d946f45 ("usb: cdns3: gadget: set fast access bit") in the
upstream kernel is taken as reference.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240424073911.1943-1-r-gunasekaran@ti.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Sam Day [Tue, 7 May 2024 18:41:23 +0000 (18:41 +0000)]
mach-snapdragon: do carveouts for qcs404 only
The newly introduced carve_out_reserved_memory causes issues when
U-Boot is chained from the lk2nd bootloader. lk2nd provides a
simple-framebuffer device and marks the framebuffer region as no-map in
the supplied /reserved-memory. Consequently, the simple_video driver
triggers a page fault when it tries to write to this region.
As per Caleb's advice, this simple patch only does the carveouts for the
qcs404 SoC for which it was originally designed. The intent is to do the
carveouts for more Qualcomm SoCs in future.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Tom Rini [Mon, 13 May 2024 15:15:51 +0000 (09:15 -0600)]
Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"
Roger Quadros <rogerq@kernel.org> says:
Sync AM62 device tree files with Linux v6.9 and
add in the missing bits in -u-boot.dtsi to get CPSW
Ethernet working.
CI testing: https://github.com/u-boot/u-boot/pull/534
Roger Quadros [Mon, 13 May 2024 12:13:56 +0000 (15:13 +0300)]
arm: dts: k3-am625-beagleplay: Fix Ethernet PHY reset GPIO
Move GPIO pinmux to MDIO node. Add GB Ethernet reset GPIO.
Add PIN_INPUT to Fix SPE ethernet reset gpio so that
reading the GPIO can give correct status.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Roger Quadros [Mon, 13 May 2024 12:13:55 +0000 (15:13 +0300)]
arm: dts: k3-am625-beagleplay: get CPSW Ethernet to work
Add missing bits in -u-boot.dtsi to get CPSW Ethernet working.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Roger Quadros [Mon, 13 May 2024 12:13:54 +0000 (15:13 +0300)]
arm: dts: k3-am62*: sync with Linux v6.9
Update k3-am62 DT files from Linux v6.9
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tom Rini [Mon, 6 May 2024 21:22:30 +0000 (15:22 -0600)]
doc/sphinx: Bump Jinja2 to 3.1.4
While we unlikely to have an issue with CVE-2024-22195, it is simple
enough to bump our version of Jinja2 to receive the fix, do so.
Reported-by: GitHub dependabot
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 13 May 2024 13:43:52 +0000 (07:43 -0600)]
Merge tag 'rpi-2024.07-rc3' of https://source.denx.de/u-boot/custodians/u-boot-raspberrypi
Updates for RPi for 2024.07:
- Switch to OF_HAS_PRIOR_STAGE by default
Tom Rini [Fri, 24 Dec 2021 16:57:04 +0000 (11:57 -0500)]
rpi: Switch to OF_HAS_PRIOR_STAGE by default
On all Raspberry Pi platforms, we're loaded by a prior stage firmware
that has assembled and passed on a device tree binary for us to use.
Switch to using this tree by default.
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: François Ozog <francois.ozog@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sun, 12 May 2024 17:36:57 +0000 (11:36 -0600)]
Merge branch 'master-cleanup' of https://source.denx.de/u-boot/custodians/u-boot-sh
Marek Vasut [Sat, 27 Apr 2024 18:59:41 +0000 (20:59 +0200)]
ARM: dts: renesas: Drop DTs with OF_UPSTREAM counterparts
Remove DTs which are now replaced by OF_UPSTREAM counterparts.
No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Adam Ford <aford173@gmail.com> #beacon boards
Tom Rini [Fri, 10 May 2024 16:44:58 +0000 (10:44 -0600)]
Merge patch series "Add AM64x Support to PRUSS and PRU_RPROC driver"
MD Danish Anwar <danishanwar@ti.com> says:
This series adds AM64x related compatibles to PRUSS and PRU_RPROC drivers.
This series is a prerequisite for ICSSG Ethernet driver.
Once Support for AM64x is added to PRUSS and PRU_RPROC driver, I'll send
another series to enable ICSSG Ethernet driver for AM64x as well.
Tom Rini [Fri, 10 May 2024 16:43:09 +0000 (10:43 -0600)]
Merge patch series "Generate all SR boot binaries"
Neha Malcom Francis <n-francis@ti.com> says:
Add support for missing HS SRs in the build for J721E and J7200.
Boot logs (updated for v2):
https://gist.github.com/nehamalcom/
e652752623537aced8cf31308015d7c9
Tom Rini [Fri, 10 May 2024 16:42:25 +0000 (10:42 -0600)]
Merge patch series "*** Commonize board code for K3 based SoMs ***"
Wadim Egorov <w.egorov@phytec.de> says:
Factor out code that we can reuse across all our K3 based SoMs.
2nd patch of this series require patch [1] to be applied first.
[1] https://lists.denx.de/pipermail/u-boot/2024-April/552021.html
Wadim Egorov [Wed, 24 Apr 2024 12:43:20 +0000 (14:43 +0200)]
arm: mach-k3: am642: Provide a way to obtain boot device for non SPLs
Let's provide get_boot_device() for AM64, similar to what we did
in commit
2f9095e2bf59 ("arm: mach-k3: am625: Provide a way to obtain boot
device for non SPLs") for AM62.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
MD Danish Anwar [Tue, 30 Apr 2024 10:46:33 +0000 (16:16 +0530)]
soc: ti: pruss: Add support for AM64x
Add support for AM64x by adding it's compatible in pruss driver.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
MD Danish Anwar [Tue, 30 Apr 2024 10:46:32 +0000 (16:16 +0530)]
remoteproc: pru: Add support for AM64x PRU / RTU cores
Add support for AM64x PRU cores by adding compatibles for AM64x.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Neha Malcom Francis [Thu, 25 Apr 2024 22:06:59 +0000 (03:36 +0530)]
arm: dts: k3-j7200-binman: Add support for HSSE1.0 and HSFS1.0
J7200 has SR1.0 and SR2.0 having three variants of each GP, HS-FS and
HS-SE. Current build does not generate HS-SE SR1.0 and HS-FS SR1.0 so
add support for them.
Reported-by: Suman Anna <s-anna@ti.com>
Reported-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Neha Malcom Francis [Thu, 25 Apr 2024 22:06:58 +0000 (03:36 +0530)]
arm: dts: k3-j721e-binman: Add support for HSFS1.1
J721E has SR1.1 and SR2.0 having three variants of each GP, HS-FS and
HS-SE. Current build does not generate HS-FS SR1.1 so add support for
them.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Wadim Egorov [Wed, 24 Apr 2024 12:53:35 +0000 (14:53 +0200)]
phycore_am64x_a53_defconfig: Enable CONFIG_BOARD_LATE_INIT
Enable CONFIG_BOARD_LATE_INIT to use PHYTECs common board_late_init()
to set handy environment variables for u-boot.
Also, resync after savedefconfig.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Wadim Egorov [Wed, 24 Apr 2024 12:53:34 +0000 (14:53 +0200)]
board: phytec: Commonize board code for K3 based SoMs
Environment handling code can be reused across all our K3 based SoMs.
Instead of adding the same code for every new SoM, move it to a common
board.c file.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tom Rini [Wed, 24 Apr 2024 22:45:37 +0000 (16:45 -0600)]
test/py: Make the number of SPL banners seen a variable
Currently we have the option to tell the console code that we should
ignore the SPL banner. We also have an option to say that we can see it
a second time, and ignore it. However, some platforms such as TI AM64x
will have us see the SPL banner three times. Rather than add an
"spl3_skipped" option, rework the code. By default we expect to see the
banner once, but boards can specify seeing it as many times as they
expect to.
Signed-off-by: Tom Rini <trini@konsulko.com>
Boon Khai Ng [Wed, 17 Apr 2024 07:46:56 +0000 (15:46 +0800)]
net: Add drivers for Sysnopsys Ethernet 10G device
This driver support the Synopsys Designware Ethernet 10G
IP block refer from the driver dwc_eth_qos.
The driver MAC register mapping is different between
Synopsys QoS IP and Synopsys 10G IP, and thus new file
is created meant for Sysnopsys 10G IP.
The dwc_eth_xgmac_socfpga.c is specific to a device family,
the driver support the specific configuration used in
Intel SoC FPGA Agilex5.
This driver is extensible for other device family to use.
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
Tom Rini [Wed, 8 May 2024 01:24:07 +0000 (19:24 -0600)]
Merge patch series "arm: Add Analog Devices SC5xx Machine Type"
Greg Malysa <greg.malysa@timesys.com> says:
This series adds support for the ADI SC5xx machine type and includes two
core drivers that are required for being able to boot any board--a UART
driver, the gptimer driver which is used as a clock reference (CNTVCNT
is not supported on the armv7 sc5xx SoCs) and the clock tree driver. Our
corresponding Linux support relies on u-boot configuring the clocks
correctly before booting, so it is not possible to boot any board
without the CGU/CDU configuration happening here. There are also no
board files, device trees, or defconfigs included here, but some common
definitions that will be used to build board files currently are. The
sc5xx SoCs themselves include many armv7 families (sc57x, sc58x, and
sc594) all using an ARM Cortex-A5, and one armv8 family (sc598) indended
to be a drop-in replacement for the SC594 in terms of peripherals, with
a Cortex-A55 instead.
Some of the configuration code in dmcinit and clkinit is quite scary and
causes a lot of checkpatch violations. It is modified from code
initially provided by ADI, but it has not been fully rewritten. There's
a question of how important it is to clean up this code--it has some
quality violations, but it has been in use (including in production) for
over two years and is known to work for performing the low level SoC
initialization, while a rewrite might introduce timing or sequence bugs
that could take a significant amount of time to detect in the future.
Greg Malysa [Thu, 25 Apr 2024 00:04:03 +0000 (20:04 -0400)]
drivers: timer: Add in driver support for ADI SC5XX-family GP timer peripheral
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Co-developed-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Nathan Barrett-Morrison [Thu, 25 Apr 2024 00:04:02 +0000 (20:04 -0400)]
drivers: serial: Add in UART for ADI SC5XX-family processors
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Nathan Barrett-Morrison [Thu, 25 Apr 2024 00:04:01 +0000 (20:04 -0400)]
drivers: clk: adi: Add in SC5XX-family clock driver
This adds support for the SC5XX clock trees which are required for reading
clock speeds on the SoCs. This is largely a port of the same support for
Linux, which has not yet been submitted upstream.
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Nathan Barrett-Morrison [Thu, 25 Apr 2024 00:04:00 +0000 (20:04 -0400)]
arch: arm: Add Analog Devices SC5xx machine type
Add support for the SC5xx machine type from Analog Devices. This
includes support for the SC57x, SC58x, SC59x, and SC59x-64 SoCs, which
have many common features such as common ADI IP blocks, and SHARC DSP
cores. This commit introduces core functionality required for all boards
using an SC5xx SoC, such as:
- SPL configuration
- Required CPU hooks such as reset
- Boot ROM interaction to load the stage 2 bootloader in the reference
configuration. Other options are possible but not officially supported
at this time
- SoC-common configuration expected to be reused by all boards
- Early initialization for system clocks and DDR controller
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Tom Rini [Tue, 7 May 2024 17:59:26 +0000 (11:59 -0600)]
Merge patch series "arm: davinci: Migrate da850-evm to OF_UPSTREAM"
- This series moves some additional 32bit TI platforms to using
OF_UPSTREAM.
Adam Ford [Wed, 1 May 2024 09:57:53 +0000 (04:57 -0500)]
arm: ti: logicpd-som-lv: Migrate to OF_UPSTREAM
The DM37 and OMAP35 SOM-LV share a few files, but both of them
can be migrated to OF_UPSTREAM with a small update to their
respective u-boot.dtsi files to address changes made the aliases.
Both defconfigs need to properly point to the upstream directory
structure for the device trees. With those updated, the U-Boot
device tree files can be deleted.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT from Makefile
Adam Ford [Wed, 1 May 2024 09:57:52 +0000 (04:57 -0500)]
arm: ti: logicpd-torpedo: Migrate to OF_UPSTREAM
The DM37 and OMAP35 Torpedo share a few files, but both of them
can be migrated to OF_UPSTREAM with a small update to their
respective u-boot.dtsi files to address changes made the aliases.
Both defconfigs need to properly point to the upstream directory
structure for the device trees. With those updated, the U-Boot
device tree files can be deleted.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT from Makefile
Adam Ford [Wed, 1 May 2024 09:57:51 +0000 (04:57 -0500)]
arm: ti: am3517_evm: Migrate to OF_UPSTREAM
With the feature of OF_UPSTREAM now available, the device trees
for the SOM and baseboard can now deleted and the device tree
locations need to point to the ti/omap directory.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT reference from Makefile.
Adam Ford [Wed, 1 May 2024 09:57:50 +0000 (04:57 -0500)]
arm: davinci: Migrate da850-evm to OF_UPSTREAM
The da850-evm can remove the U-Boot device trees if migrated
to OF_UPSTREAM. This means pointing the device trees to the
ti/davinci directory.
Signed-off-by: Adam Ford <aford173@gmail.com>
v2: Remove DTS from Makefile.
Tom Rini [Tue, 7 May 2024 14:27:24 +0000 (08:27 -0600)]
Merge tag 'u-boot-rockchip-
20240507' of https://source.denx.de/u-boot/custodians/u-boot-rockchip
CI: https://source.denx.de/u-boot/custodians/u-boot-rockchip/-/pipelines/20628
- migrate to use OF_UPSTREAM for rv1108, rk3308, rk3328, rk356x, rk3588;
Tom Rini [Tue, 7 May 2024 14:01:06 +0000 (08:01 -0600)]
Merge branch '2024-05-06-remove-include-common_h' into next
- Merge the four series that I made to finally remove include/common.h.
For the most part, this is just removing <common.h> entirely. In a few
cases we needed to add <linux/types.h> or <time.h>. In the case of
PowerPC related code, we instead need to bring in <asm/ppc.h>.
Tom Rini [Thu, 2 May 2024 01:31:38 +0000 (19:31 -0600)]
common.h: Remove this file and all references
With all files that had included this file directly having been updated,
we can now remove this file.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:37 +0000 (19:31 -0600)]
api: Remove <common.h> and add needed includes
Remove <common.h> from here and when needed add missing include files
directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:36 +0000 (19:31 -0600)]
xen: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:35 +0000 (19:31 -0600)]
watchdog: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Acked-by: Angelo Dureghello <angelo@kernel-space.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:34 +0000 (19:31 -0600)]
w1-eeprom: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:33 +0000 (19:31 -0600)]
w1: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:32 +0000 (19:31 -0600)]
virtio: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:31 +0000 (19:31 -0600)]
video: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:30 +0000 (19:31 -0600)]
usb: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:29 +0000 (19:31 -0600)]
ufs: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:28 +0000 (19:31 -0600)]
tpm: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:27 +0000 (19:31 -0600)]
timer: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:26 +0000 (19:31 -0600)]
thermal: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:25 +0000 (19:31 -0600)]
sysreset: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:24 +0000 (19:31 -0600)]
sysinfo: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:23 +0000 (19:31 -0600)]
spmi: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:22 +0000 (19:31 -0600)]
spi: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:21 +0000 (19:31 -0600)]
sound: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:20 +0000 (19:31 -0600)]
soc: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:19 +0000 (19:31 -0600)]
smem: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:18 +0000 (19:31 -0600)]
sm: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:17 +0000 (19:31 -0600)]
serial: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:16 +0000 (19:31 -0600)]
scsi: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:15 +0000 (19:31 -0600)]
rtc: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:14 +0000 (19:31 -0600)]
reset: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:13 +0000 (19:31 -0600)]
remoteproc: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:12 +0000 (19:31 -0600)]
reboot-mode: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:11 +0000 (19:31 -0600)]
ram: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:10 +0000 (19:31 -0600)]
pwm: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:09 +0000 (19:31 -0600)]
power: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:08 +0000 (19:31 -0600)]
pinctrl: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:07 +0000 (19:31 -0600)]
phy: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:06 +0000 (19:31 -0600)]
pci_endpoint: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:05 +0000 (19:31 -0600)]
pci: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:04 +0000 (19:31 -0600)]
pch: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:03 +0000 (19:31 -0600)]
nvme: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 2 May 2024 01:31:02 +0000 (19:31 -0600)]
net: Remove <common.h> and add needed includes
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>