Samuel Holland [Thu, 22 Oct 2020 02:12:09 +0000 (21:12 -0500)]
binman: Only write FDT once per node
Due to an extra level of indentation, the "data" property containing the
FDT was being written repeatedly after every other property in the node.
This caused the generated FIT image to be invalid.
Move the block up one level, so the property is added exactly once.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Samuel Holland [Thu, 22 Oct 2020 02:12:08 +0000 (21:12 -0500)]
Makefile: Only define u-boot.itb rule when applicable
If neither CONFIG_SPL_FIT_SOURCE nor CONFIG_USE_SPL_FIT_GENERATOR is
enabled, U_BOOT_ITS will be undefined, and attempting to make u-boot.itb
will pass invalid arguments to mkimage, causing it to print its help
message.
Remove the rule in that case, so it is more obvious that u-boot.itb is
not something that can be made. This will reduce confusion as platforms
move away from CONFIG_USE_SPL_FIT_GENERATOR, as u-boot.itb was
previously a valid goal for those platforms.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Icenowy Zheng [Fri, 16 Oct 2020 09:33:08 +0000 (17:33 +0800)]
sunxi: make V3s DRAM initialization more proper
Previously, because we have no source code about the DRAM initialization
of V3s and missing some configurations (delays and MBUS QoS info), our
V3s DRAM initialization sequence is hacked from the H3 one.
As the SDK shipped with PineCube contains source code for V3s libdram,
we can retrieve these information from it and tweak some other magic
bits.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The current default of 0x400 for SYS_MALLOC_F_LEN is too small if any
additional drivers marked as DM_FLAG_PRE_RELOC are loaded before
relocation.
CONFIG_RSA=y which is needed for UEFI secure boot or for FIT image
verification loads the driver mod_exp_sw which has DM_FLAG_PRE_RELOC.
CONFIG_LOG=Y is another setting requiring additional early malloc
area, cf. log_init().
When running pine64-lts_defconfig with CONFIG_RSA=y and debug UART enabled
we see as output in main U-Boot
alloc_simple() alloc space exhausted
With this patch the default values of SYS_MALLOC_F_LEN and
SPL_SYS_MALLOC_F_LEN on ARCH_SUNXI are raised to 0x2000.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Update email address of Maxime Ripard in git-mailrc to match more
recently updated entry in MAINTAINERS.
commit 9bd9b2bcbee1 ("MAINTAINERS: Update my email address")
commit bf8f4c4400e3 ("MAINTAINERS: Update email address for Maxime Ripard")
Signed-off-by: Jonas Smedegaard <dr@jones.dk> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:46 +0000 (01:40 +0100)]
sunxi: Pine-H64: Explicitly enable PHY regulator
According to the devicetree and the schematic, the 3.3V power rail for
the PHY is enabled by GPIO PC16. It's wired as active-high, with a
pull-up resistor, so actually works already when the GPIO is in
High-Z state.
However we should not take any chances and explicitly set the GPIO pin
to high, to avoid accidentally losing the PHY power.
The existing MACPWR Kconfig allows to do this easily.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:45 +0000 (01:40 +0100)]
net: sun8i-emac: Lower MDIO frequency
When sending a command via the MDIO bus, the Designware MAC expects some
bits in the CMD register to describe the clock divider value between
the main clock and the MDIO clock.
So far we were omitting these bits, resulting in setting "00", which
means "/ 16", so ending up with an MDIO frequency of either 18.75 or
12.5 MHz.
All the internal PHYs in the H3/H5/H6 SoCs as well as the Gbit Realtek
PHYs seem to be fine with that - although it looks like to be severly
overclocked (the MDIO spec limits the frequency to 2.5 MHz).
However the external 100Mbit PHY on the Pine64 (non-plus) board is
not happy with that, Ethernet was actually never working there, as the
PHY didn't probe.
As we set the EMAC clock (via AHB2) to 300 MHz in ATF (on the 64-bit
SoCs), and use 200 MHz on the H3, we need the highest divider of 128
to let the MDIO clock end up below the required 2.5 MHz.
This enables Ethernet on the Pine64(non-plus).
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Wed, 21 Oct 2020 17:57:32 +0000 (23:27 +0530)]
net: sun8i-emac: Make internal PHY handling more robust
The current implementation of sun8i_get_ephy_nodes() makes quite some
assumptions, in general relying on DT path names is a bad idea.
I think the idea of the code was to determine if we are using the
internal PHY, for which there are simpler and more robust methods:
Rewrite (and rename) the existing function to simply lookup the DT node
that "phy-handle" points to, using the device's DT node.
Then check whether the parent of that PHY node is using an "H3 internal
MDIO" compatible string. If we ever get another internal MDIO bus
implementation, we will probably need code adjustments anyway, so this
is good enough for now.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: rebase on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:43 +0000 (01:40 +0100)]
net: sun8i_emac: Simplify and fix error handling for RX
The error handling in recv() is somewhat broken, for instance
good_packet isn't really used, and it's hardly readable. Also we try
to check for short or too big packets, but those are actually filtered
out by the hardware.
Simplify the whole routine and improve the error handling:
- Bail out early if the current RX descriptor is not ready.
- Enable propagation of runt, huge and broken packets.
- Check for runt and huge packets, and return 0 to indicate this.
This will force the framework to call free_pkt for cleanup.
- Avoid aligning the packet buffer for invalidation again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:42 +0000 (01:40 +0100)]
net: sun8i_emac: Fix MAC soft reset
The EMAC soft reset routine was subtly broken, using an open coded
timeout routine without any actual delay.
Remove the unneeded initial reset bit read, and call wait_for_bit_le32()
to handle the timeout correctly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:41 +0000 (01:40 +0100)]
net: sun8i_emac: Fix overlong lines
When iterating over all RX/TX buffers, we were using a rather long "idx"
control variable, which lead to a nasty overlong line.
Replace "idx" with "i" to avoid this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:40 +0000 (01:40 +0100)]
net: sun8i_emac: Wrap and simplify cache maintenance operations
To meet the current alignment requirements for our cache maintenance
functions, we were explicitly aligning the *arguments* to those calls.
This is not only ugly to read, but also wrong, as we need to make sure
we are not accidentally stepping on other data.
Provide wrapper functions for the common case of cleaning or
invalidating a descriptor, to make the cache maintenance calls more
readable. This fixes a good deal of the problematic calls.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:39 +0000 (01:40 +0100)]
net: sun8i_emac: Drop unneeded cache invalidation before sending
There is no reason to invalidate a TX descriptor before we are setting
it up, as we will only write to a field.
Remove the not needed invalidate_dcache_range() call.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:38 +0000 (01:40 +0100)]
net: sun8i_emac: Reduce cache maintenance on TX descriptor init
When we initialise the TX descriptors, there is no need yet to clean
them all to memory, as they don't contain any data yet. Later we will
touch and clean each descriptor anyway.
However we tell the MAC about the beginning of the chain, so we have to
clean at least the first descriptor, to make it clear that this is empty
and there are no packets to transfer yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:37 +0000 (01:40 +0100)]
net: sun8i_emac: Improve cache maintenance on RX descriptor init
Before we initialise the RX descriptors, there is no need to *clean*
them from the cache, as we touch them for the first time.
However we should cover the case that those buffers contain dirty cache
lines, which could be evicted and written back to DRAM any time later,
in the worst case *after* the MAC has transferred a packet into them.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:36 +0000 (01:40 +0100)]
net: sun8i_emac: Name magic bits and simplify read-modify-write calls
The EMAC driver contains a lot of magic bits, although the manuals
and the Linux driver have all names for them.
Define those names and use them when programming the registers.
Also this replaces a lot of readl/mask/writel operations with the much
easier-to-read setbits_le32() macro.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Apparently due to copying from some older or converted driver, the
sun8i_emac driver contains pointless wrapper functions to bridge
between a legacy driver and the driver model.
Since sun8i_emac is (and always was) driver model only, there is no
reason to have those confusing wrappers. Just remove them, and use
the driver model prototypes directly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When preparing the register value for the MDIO command register, we
start with a zeroed register, so there is no need to mask off certain
bits before setting them.
Simplify the sequence, and rename the variable to a more matching
mii_cmd on the way.
Also the open-coded time-out routine can be replaced with a much safer
and easier-to-read call to wait_for_bit_le32().
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:33 +0000 (01:40 +0100)]
net: sun8i_emac: Don't hand out TX descriptor too early
When initialising the TX DMA descriptors, we mostly chain them up,
but of course don't know about any data or its length yet.
That means they are still invalid, and the OWN bit should NOT be set
yet.
In fact when we later tell the MAC about the beginning of the chain,
and enable TX DMA in the start() routine, the MAC will start fetching
TX descriptors prematurely, as it can be seen by dumping the TX_DMA_STA
and TX_DMA_CUR_DESC registers.
Clear the owner bit, to not give the MAC the wrong illusion that it
owns the descriptors already.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Mon, 6 Jul 2020 00:40:32 +0000 (01:40 +0100)]
net: sun8i-emac: Bail out on PHY error
When phy_startup() returns with an error, because there is no link or
the user interrupted the process, we shall stop the _start() routine
and return with an error, instead of proceeding anyway.
This fixes pointless operations when there is no Ethernet cable
connected, for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+ Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tom Rini [Mon, 19 Oct 2020 13:29:05 +0000 (09:29 -0400)]
Merge tag 'u-boot-atmel-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.01 cycle:
This feature set brings the rework of the clock tree for sam9x60 SoC.
This makes the clock tree fully compatible with Common Clock Framework
and allows full clock configuration in U-Boot. This means that the
sam9x60 boards can boot now using U-Boot.
This also includes the definitions for sam9x60 SiPs and a divisor fix
for the clock on sama7g5 SoC.
Patrick Delaunay [Mon, 28 Sep 2020 09:30:14 +0000 (11:30 +0200)]
configs: migrate CONFIG_VIDEO_BMP_GZIP to defconfigs
Done with:
./tools/moveconfig.py VIDEO_BMP_GZIP
The 3 suspicious migration because CMD_BMP and SPLASH_SCREEN
are not activated in these defconfigs:
- trats_defconfig
- s5pc210_universal_defconfig
- trats2_defconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Neil Armstrong [Fri, 2 Oct 2020 09:16:09 +0000 (11:16 +0200)]
video: dw-mipi-dsi: permit configuring the escape clock rate
The Amlogic D-PHY in the Amlogic AXG SoC Family does support a frequency
higher than 10MHz for the TX Escape Clock, thus make the target rate
configurable.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] a328ca7e4af3 ("drm/bridge: dw-mipi-dsi: permit configuring the escape clock rate")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 2 Oct 2020 09:16:08 +0000 (11:16 +0200)]
video: dw-mipi-dsi: driver-specific configuration of phy timings
The timing values for dw-dsi are often dependent on the used display and
according to Philippe Cornu will most likely also depend on the used phy
technology in the soc-specific implementation.
To solve this and allow specific implementations to define them as needed
add a new get_timing callback to phy_ops and call this from the dphy_timing
function to retrieve the necessary values for the specific mode.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] 25ed8aeb9c39 ("drm/bridge/synopsys: dsi: driver-specific configuration of phy timings")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sean Anderson [Tue, 13 Oct 2020 19:20:52 +0000 (15:20 -0400)]
test: Fix sandbox tests failing to build
syslog_test.h is in test/log/, not include/
Fixes: 52d3df7fef ("log: Allow LOG_DEBUG to always enable log output") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
watchdog: octeontx_wdt: Add support for start and stop
This patch enhances the Octeon TX/TX2 watchdog driver to fully enable
the WDT. With this changes, the "wdt" command is now also supported
on these platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Aaron Williams <awilliams@marvell.com> Cc: Suneel Garapati <sgarapati@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com>
Tom Rini [Thu, 15 Oct 2020 12:20:42 +0000 (08:20 -0400)]
Merge tag 'mmc-2020-10-14' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmc
- fsl_esdhc_imx cleanup
- not send cm13 if send_status is 0.
- Add reinit API
- Add mmc HS400 for fsl_esdhc
- Several cleanup for fsl_esdhc
- Add ADMA2 for sdhci
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
Set the defaults on probe for the packet buffer size registers
for the i210.
The TX/RX PBSIZE register of the i210 resets to its default value
only at power-on - see Intel Ethernet Controller I210 Datasheet rev 3.5
chapter 8.3 'Internal Packet Buffer Size Registers'.
If something (another driver, another OS, etc.) modifies this register
from its default value, the e1000 driver doesn't function correctly. It
detects a hang of the transmitter and continuously resets the adapter.
Here we set this value to its default when resetting the i210 to
resolve this issue.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
checkpatch.pl: Make CONFIG_IS_ENABLED(CONFIG_*) an error
CONFIG_IS_ENABLED() takes the kconfig name without the CONFIG_ prefix,
e.g. CONFIG_IS_ENABLED(CLK) for CONFIG_CLK. Make including the prefix
an error in checkpatch.pl so calls in the wrong format aren't
accidentally reintroduced.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_IS_ENABLED() takes the kconfig name without the CONFIG_ prefix,
e.g. CONFIG_IS_ENABLED(CLK) for CONFIG_CLK. Some of these were being
fixed every now and then, see:
Sean Anderson [Wed, 9 Sep 2020 20:24:56 +0000 (16:24 -0400)]
time: Fix get_ticks being non-monotonic
get_ticks does not always succeed. Sometimes it can be called before the
timer has been initialized. If it does, it returns a negative errno.
This causes the timer to appear non-monotonic, because the value will
become much smaller after the timer is initialized.
No users of get_ticks which I checked handle errors of this kind. Further,
functions like tick_to_time mangle the result of get_ticks, making it very
unlikely that one could check for an error without suggesting a patch such
as this one.
This patch panics if we ever get an error. There are two cases in which
this can occur. The first is if we couldn't find/probe the timer for some
reason. One reason for this is if the timer is not available so early. This
likely indicates misconfiguration. Another reason is that the timer has an
invalid/missing device tree binding. In this case, panicing is also
correct. The second case covers errors calling get_count. This can only
occur if the timer is missing a get_count function (or on RISC-V, but that
should be fixed soon).
Fixes: c8a7ba9e6a5 Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
David Woodhouse [Tue, 4 Aug 2020 09:05:47 +0000 (10:05 +0100)]
env/ext4.c: allow loading from an EXT4 partition on the MMC boot device
This parallels what I added for FAT in commit 6731bef6966, allowing the
environment to be found in a specific partition on the device that the
board's mmc_get_env_dev() returns. On the Banana Pi R2 that means the
device that U-Boot was loaded from; either the internal eMMC or an SD
card.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Frédéric Danis [Fri, 20 Mar 2020 09:59:24 +0000 (10:59 +0100)]
cmd: Fixup DT to pass PStore Ramoops parameters
To simplify configuration and keep synchronized the PStore/Ramoops between
U-Boot and the Linux kernel, this commit dynamically adds the Ramoops
parameters defined in the U-Boot session to the Device Tree.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com> Cc: Tom Rini <trini@konsulko.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
Frédéric Danis [Fri, 20 Mar 2020 09:59:23 +0000 (10:59 +0100)]
test: Add PStore command tests
Add PStore command to sandbox and sandbox64 defconfigs.
Add test checking:
- 'pstore display' of all records
- 'pstore display' only the 2nd dump record
- 'pstore save' of all records
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
[trini: Adjust to always load files from source directory] Signed-off-by: Tom Rini <trini@konsulko.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
Frédéric Danis [Fri, 20 Mar 2020 09:59:22 +0000 (10:59 +0100)]
cmd: Add command to display or save Linux PStore dumps
This patch adds a new pstore command allowing to display or save ramoops
logs (oops, panic, console, ftrace and user) generated by a previous
kernel crash.
PStore parameters can be set in U-Boot configuration file, or at run-time
using "pstore set" command. Records size should be the same as the ones
used by kernel, and should be a power of 2.
This command allows:
- to display uncompressed logs
- to save compressed or uncompressed logs, compressed logs are saved as a
compressed stream, it may need some work to be able to decompress it,
e.g. adding a fake header:
"printf "\x1f\x8b\x08\x00\x00\x00\x00\x00\x00\x00" |
cat - dmesg-ramoops-0.enc.z | gzip -dc"
- ECC part is not used to check memory corruption
- only 1st FTrace log is displayed or saved
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
[trini: Minor updates for current design, correct spacing in rST] Signed-off-by: Tom Rini <trini@konsulko.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
Michael Walle [Mon, 12 Oct 2020 08:07:14 +0000 (10:07 +0200)]
mmc: fsl_esdhc: add ADMA2 support
Newer eSDHC controllers support ADMA2 descriptor tables which support
64bit DMA addresses. One notable user of addresses in the upper memory
segment is the EFI loader.
If support is enabled, but the controller doesn't support ADMA2, we
will fall back to SDMA (and thus 32 bit DMA addresses only).
Andre Heider [Fri, 4 Sep 2020 15:33:54 +0000 (17:33 +0200)]
arm64: dts: a3720: add support for espressobin with populated emmc
Import armada-3720-espressobin-emmc.dts from Linux, but use sdhc1 for
emmc, since our dtsi is still based on downstream and sdhc0 is used for
the sd card.
Add support for this, while retaining backward-compatibility with
existing device trees; the driver will preserve existing behavior if a
cs-gpios list is not given, or if a particular line is specified as <0>
(native).
This implementation is inspired by similar implementations in
neighboring drivers for other platforms: atmega, mxc, etc.
Signed-off-by: George Hilliard <ghilliar@amazon.com> Reviewed-by: Stefan Roese <sr@denx.de>
Luka Kovacic [Fri, 28 Aug 2020 22:35:51 +0000 (00:35 +0200)]
arm: mvebu: mvebu_armada-8k: Add support for initializing iEi Puzzle-M801 networking
Add support for the marvell,armada8040-puzzle-m801 compatible string
in the board/Marvell/mvebu_armada-8k/board.c file to initialize the
networking on iEi Puzzle-M801 board (2x CP1 1 Gb ports).
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr> Reviewed-by: Stefan Roese <sr@denx.de>
projects / u-boot.git / log