Albert ARIBAUD [Fri, 12 Apr 2013 05:14:30 +0000 (05:14 +0000)]
ARM: fix CONFIG_SPL_MAX_SIZE semantics
Remove SPL-related ASSERT() in arch/arm/cpu/u-boot.lds
as this file is never used for SPL builds.
Rewrite the ASSERT() in arch/arm/cpu/u-boot-spl.lds
to separately test image (text,data,rodata...) size,
BSS size, and full footprint each against its own max,
and make Tegra boards check full footprint.
Also, output section mmutable is not used in SPL builds.
Remove it.
Finally, update README regarding the (now homogeneous)
semantics of CONFIG_SPL_[BSS_]MAX_SIZE and add the new
CONFIG_SPL_MAX_FOOTPRINT macro.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Andrew Gabbasov [Sun, 7 Apr 2013 23:06:08 +0000 (23:06 +0000)]
fsl_esdhc: Fix DMA transfer completion waiting loop
Rework the waiting for transfer completion loop condition
to continue waiting until both Transfer Complete and DMA End
interrupts occur. Checking of DLA bit in Present State register
looks not needed in addition to interrupts status checking,
so it can be removed from the condition. Also, DMA Error
condition is added to the list of data errors, checked in the loop.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Albert ARIBAUD [Thu, 11 Apr 2013 05:43:21 +0000 (05:43 +0000)]
ARM: Fix __bss_start and __bss_end in linker scripts
Commit 3ebd1cbc introduced compiler-generated __bss_start
and __bss_end__ and commit c23561e7 rewrote all __bss_end__
as __bss_end. Their merge caused silent and harmless but
potentially bug-inducing clashes between compiler- and linker-
generated __bss_end symbols.
Make __bss_end and __bss_start compiler-only, and create
__bss_base and __bss_limit for linker-only use.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The glitch in the SPI clock line, which commit 3cea335c34 (spi: mxc_spi: Fix spi
clock glitch durant reset) solved, is back now and itwas re-introduced by
commit d36b39bf0d (spi: mxc_spi: Fix ECSPI reset handling).
Actually the glitch is happening due to always toggling between slave mode
and master mode by configuring the CHANNEL_MODE bits in this reset function.
Since the spi driver only supports master mode, set the mode for all channels
always to master mode in order to have a stable, "glitch-free" SPI clock line.
When swi instruction is executed, it is expected to get message
"software interrupt" in console and dump registers and reboot, as
do_software_interrupt() in arch/arm/lib/interrupts.c.
But, actually it causes data abort accessing wrong address in get_bad_stack_swi
macro in arch/arm/cpu/v7/start.S.
This patch fixes this problem.
The same mistake in arch/arm/cpu/{arm1136,arm1176,pxa}/start.S.
Tom Rini [Fri, 12 Apr 2013 16:38:16 +0000 (12:38 -0400)]
am335x: Really correct DDR timings on new BeagleBone part
The previous timings were done on the internal-only A1 board which has
different DDR part than all later revs. The timings need a slight
adjustment to be correct in all cases with later revs.
Holger Brunck [Tue, 15 Jan 2013 22:51:22 +0000 (22:51 +0000)]
arm/km: add support for kmsuv31 board
This board is from a u-boot point of view a mixture between kmnusa and
a standard km_kirkwood board. We have our u-boot environment in the spi
NOR flash, but we have a direct connection between the kirkwood and the
piggy. A FPGA is connected via the PCIe interface. So we only have to
select the specific features in the board setup.
Holger Brunck [Tue, 15 Jan 2013 22:51:20 +0000 (22:51 +0000)]
arm/km: rename BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
commit 9660e442 cosmetic: s/BOARD_LATE_INIT/CONFIG_BOARD_LATE_INIT
removes BOARD_LATE_INIT and uses CONFIG_BOARD_LATE_INIT instead.
Therefore we have to use this define.
arm: Make all linker scripts compatible with per-symbol sections
Let all ARM linker scripts handle properly -ffunction-sections
and -fdata-sections. This will be useful for future changes in order to create
symbol-specific sections in common .S files.
Following the removal of the smdk6400 board, the MMU setup code in
arm1176/start.S becomes unused, so remove it. It will still be possible to
restore it later from the Git history if necessary, in which case it should be
moved out of the relocate_code() function.
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
The migration of boards from Makefile to boards.cfg was due for v2012.03, but
smdk6400 did not follow, and it does not build, so move it to scrapyard. It will
still be possible to restore it from the Git history before fixing it.
make never uses the SHELL variable from the environment. Instead, it
uses /bin/sh, or the value assigned to the SHELL variable by the Makefile. This
makes the export of the SHELL variable useless for sub-makes (but still useful
for the environment of recipes). However, we want all makes to use the same
shell.
This patch fixes this issue by moving the SHELL variable setup and export to the
top config.mk, so that all Makefile-s including it use the same shell.
Since BASH is used by default, this makes it possible to use things
like 'echo -e ...' in sub-makes, which would otherwise fail e.g. with /bin/sh
symlinked to /bin/dash on Ubuntu.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Reviewed-by: Tom Rini <trini@ti.com>
Commit e05e5de7fae5bec79617e113916dac6631251156 made the 2 1st parameters of
ARM's relocate_code() useless since it moved the code handling them to crt0.S.
So, drop these parameters.
Automatically build the 'u-boot.imx' (i.e. imx header + u-boot.bin) and 'SPL'
(i.e. imx header + u-boot-spl.bin) make targets for all imx processors
supporting this header, so for arm926ejs, arm1136 and armv7. Some combinations
were missing.
At the same time, fix the build of SPL targets not supporting the imx header on
arm1136. For arm1136, the 'SPL' make target was forced to build in all cases if
CONFIG_SPL_BUILD was defined, even for non-imx platforms or imx setups without
an imx header.
autoconfig.mk: Make it possible to define configs from other configs
Give more flexibility to define configs that can be interpreted by make, e.g. to
define fallback values of configs like in the example below.
Before this change, the config lines:
#define CONFIG_SPL_MAX_SIZE 2048
#define CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE
would have been changed in autoconfig.mk into:
CONFIG_SPL_MAX_SIZE=2048
CONFIG_SPL_PAD_TO="CONFIG_SPL_MAX_SIZE"
Hence, a make recipe using as an argument to $(OBJCOPY):
--pad-to=$(CONFIG_SPL_PAD_TO)
would have issued:
--pad-to="CONFIG_SPL_MAX_SIZE"
which means nothing for $(OBJCOPY) and makes it fail.
Thanks to this change, the config lines above are changed in autoconfig.mk into:
CONFIG_SPL_MAX_SIZE=2048
CONFIG_SPL_PAD_TO=$(CONFIG_SPL_MAX_SIZE)
Hence, the make recipe above now issues:
--pad-to=2048
as expected from the defined config.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Reviewed-by: Tom Rini <trini@ti.com>
arm: relocate_code(): Use __image_copy_end for end of relocation
Use __image_copy_end instead of __bss_start for the end of the image to
relocate. This is the same as commit 033ca72, but applied to all ARM start.S.
This is a more appropriate symbol naming for an image copy & relocate feature,
and this also saves a useless copy of data put between __image_copy_end and
__bss_start in linker scripts (e.g. relocation information, or MMU
initialization tables used only before jumping to the relocated image).
Currently is_16bit_nand() is a per SoC function and it decides the bus nand
width by reading some boot related registers.
This method works when NAND is the boot medium, but does not work if another
boot medium is used. For example: booting from a SD card and then using NAND
to store the environment variables, would lead to the following error:
NAND bus width 16 instead 8 bit
No NAND device found!!!
0 MiB
Use CONFIG_SYS_NAND_BUSWIDTH_16BIT symbol to decide the bus width.
If it is defined in the board file, then consider 16-bit NAND bus-width,
otherwise assume 8-bit NAND is used.
This also aligns with Documentation/devicetree/bindings/mtd/nand.txt, which
states:
nand-bus-width : 8 or 16 bus width if not present 8
Joe Hershberger [Mon, 8 Apr 2013 10:32:50 +0000 (10:32 +0000)]
mtd: Make mtdparts work with pre-reloc env
The env in UBI needs to look up the mtd partition as part of relocation,
which happens before relocation. Make the mtdparts code capable of
working on the default env to start with.
The code tries to set values in the env as well, but again, the env
isn't there yet, so add a check to setenv to not allow sets before the
env is relocated.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Jon Hunter [Tue, 9 Apr 2013 21:41:32 +0000 (16:41 -0500)]
omap5912-osk: Increase flash partition for u-boot
The current u-boot binary needs more than 128KB of flash space and so
move the u-boot environment from an offset of 128KB to 256KB in flash
to ensure the enviroment does not overlap with u-boot.
Jon Hunter [Tue, 9 Apr 2013 21:41:31 +0000 (16:41 -0500)]
omap5912-osk: Fix device initialisation
In the current u-boot, the device pin multiplexing and clock
initialisation needs to be early during the boot process and before
board_init() is called. U-boot is currently crashing on this board
because this is not being done early enough. Therefore, add a s_init()
function for the omap5912-osk board to do this.
Also fix the stack pointer so that it is pointing to the end of the
internal RAM and not the beginning as this was also causing the device
to crash.
Jon Hunter [Tue, 9 Apr 2013 21:41:30 +0000 (16:41 -0500)]
omap5912-osk: Fix booting from NOR flash
The omap5912-osk board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash at address
0x00000000.
The omap5912-osk board only has 32MB of RAM and so fix the comment
in the omap5912-osk config.mk file as well.
Jon Hunter [Tue, 9 Apr 2013 21:41:29 +0000 (16:41 -0500)]
omap5912-osk: Fix DRAM initialisation
The size of the DRAM for the omap5912-osk board is getting setup in the
dram_init() function. However, for the current u-boot release this is
too late and needs to be done in dram_init_banksize(). Therefore, add
a dram_init_banksize() function for the omap5912-osk board and setup the
DRAM size there.
The omap4460_volts struct was incorrectly referencing tps62361
instead of twl6030 as PMIC for the core and mm voltages (the
tps is used for mpu supply only). This shall lead to bad OPP
settings while booting kernel. Fixing it.
powerpc/lib: fix unsafe register handling in wait_ticks
If watchdog is enabled, the arch/powerpc/lib/ticks.S::wait_ticks() function
calls the function specified by the WATCHDOG_RESET macro.
The wait_ticks function depends on the registers r0, r6 and r7 being
preserved however that is not guaranteed, e.g. if the reset function is a
C function this will probably overwrite r0 and cause an endless loop.
The following patch changes to using r14+r15 instead of r6+r7 (to resemble
what would have been generated by a C compiler) and saves all necessary
registers on the stack.
The patch has been tested on a custom MPC5125 based machine using the 512x
powerpc architecture.
Signed-off-by: Mats Karrman <mats.karrman@tritech.se> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Tested-by: Stefan Roese <sr@denx.de>
ramneek mehresh [Sun, 17 Feb 2013 18:23:32 +0000 (18:23 +0000)]
powerpc/usb: Fix usb device-tree fix-up
Fix USB device-tree fixup to properly handle device-tree fixup and
print appropriate message when wrong/junk "dr_mode" or "phy_type"
are mentioned in hwconfig string
am335x_evm: Enable DFU for NAND and MMC, provide example alt_infos
- Add CONFIG_DFU_NAND, CONFIG_DFU_MMC
- Set dfu_alt_info_nand, dfu_alt_info_emmc and dfu_alt_info_mmc to show
working examples for those cases.
- Increase CONFIG_SYS_MAXARGS due to hush parsing bugs that would
otherwise disallow 'setenv dfu_alt_info ${dfu_alt_info_nand}'.
- Enable CONFIG_FAT_WRITE to allow updating on MMC
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Thu, 14 Mar 2013 05:32:50 +0000 (05:32 +0000)]
nand: Extend nand_(read|write)_skip_bad with *actual and limit parameters
We make these two functions take a size_t pointer to how much space
was used on NAND to read or write the buffer (when reads/writes happen)
so that bad blocks can be accounted for. We also make them take an
loff_t limit on how much data can be read or written. This means that
we can now catch the case of when writing to a partition would exceed
the partition size due to bad blocks. To do this we also need to make
check_skip_len count not just complete blocks used but partial ones as
well. All callers of nand_(read|write)_skip_bad are adjusted to call
these with the most sensible limits available.
The changes were started by Pantelis and finished by Tom.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com>
Previously we didn't support upload/download larger than available
memory. This is pretty bad when you have to update your root filesystem
for example.
This patch removes that limitation (and the crashes when you transfered
any file larger than 4MB) by making raw image writes be done in chunks
and making file maximum size be configurable.
The sequence number is a 16 bit counter; make sure we handle rollover
correctly. This fixes the wrong transfers for large (> 256MB) images.
Also utilize a variable to handle initialization, so that we don't rely
on just the counter sent by the host.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com>
Simon Glass [Tue, 26 Mar 2013 13:09:44 +0000 (13:09 +0000)]
patman: Add Series-process-log tag to sort/uniq change logs
For some series with lots of changes it is annoying that duplicate change
log items are not caught. It is also helpful sometimes to sort the change
logs.
Add a Series-process-log tag to enable this, which can be placed in a
commit to control this.
The change to the Cc: line is to fix a checkpatch warning.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Simon Glass [Tue, 26 Mar 2013 13:09:43 +0000 (13:09 +0000)]
patman: Add -a option to refrain from test-applying the patches
Especially with the Linux kernel, it takes a long time (a minute or more)
to test-apply the patches, so patman becomes significantly less useful.
The only real problem that is found with this apply step is trailing spaces.
Provide a -a option to skip this step, for those working with clean patches.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Doug Anderson [Fri, 1 Mar 2013 11:11:07 +0000 (11:11 +0000)]
patman: Don't barf if the word 'commit' starts a line
Patman's regular expression for detecting the start of a
commit in a git log was a little simplistic and could be
confused if the git log itself had the word "commit" as
the start of a line (as this commit does). Make patman
a little more robust.
Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 26 Mar 2013 13:09:42 +0000 (13:09 +0000)]
patman: Provide option to ignore bad aliases
Often it happens that patches include tags which don't have aliases. It
is annoying that patman fails in this case, and provides no option to
continue other than adding empty tags to the .patman file.
Correct this by adding a '-t' option to ignore tags that don't exist.
Print a warning instead.
Since running the tests is not a common operation, move this to --test
instead, to reserve -t for this new option.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Mingkai Hu [Sun, 7 Apr 2013 22:13:32 +0000 (22:13 +0000)]
cmd_sf: include header file common.h before div64.h
The header file div64.h includes <asm/types.h> which defines
the phys_addr_t according to the macro CONFIG_PHYS_64BIT, while
the macro CONFIG_PHYS_64BIT is included in common.h which comes
after div64.h, so in order to get consistent type definition for
phys_addr_t, common.h should be included before div64.h, Or else,
the parameters of phys_addr_t type will be passed wrongly when
CONFIG_PHYS_64BIT is defined.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
introduced cleanup of ext4write semantics to be consistent with other
filesystem's writing commands (e.g. fatwrite).
This commit provides correct ext4write command generation at DFU eMMC
code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tom Rini [Fri, 5 Apr 2013 06:21:45 +0000 (06:21 +0000)]
omap5_uevm.h: Move uEVM-specific choices to omap5_uevm.h
The omap5_uevm platform has eMMC, and it makes sense to say that our
default env storage shall reside there. Other platforms may not, so
move this choice to the EVM config. In addition, we should provide some
way to partition the flash for later usage, so take advantage of the GPT
partition table support code and allow that to be setup with some
reasonable defaults.
Cc: Sricharan R <r.sricharan@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 5 Apr 2013 06:21:44 +0000 (06:21 +0000)]
OMAP3/4/5/AM33xx: Correct logic for checking FAT or RAW MMC
In the case of booting from certain peripherals, such as UART, we must
not see what the device descriptor says for RAW or FAT mode because in
addition to being nonsensical, it leads to a hang. This is why we have
a test currently for the boot mode being within range. The problem
however is that on some platforms we get MMC2_2 as the boot mode and not
the defined value for MMC2, and in others we get the value for MMC2_2.
This is required to fix eMMC booting on omap5_uevm.
Tested on am335x_evm (UART, NAND, SD), omap3_beagle (NAND, SD on
classic, SD only on xM rev C5) and omap5_uevm (SD, eMMC).
Commit "8602114 omap: emif: configure emif only when required"
breaks SDRAM_AUTO_DETECTION.
The issue is dmm_init() depends on emif_sizes[](SDRAM Auto detection)
done in do_sdram_init(). The above commit moves dmm_init() above
do_sdram_init() because of which dmm_init() uses uninitialized
emif_sizes[].
So instead of using global emif_sizes[], get sdram details locally
and calculate emif sizes.
Reported-by: Michael Cashwell <mboards@prograde.net> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
SRICHARAN R [Thu, 4 Apr 2013 23:39:47 +0000 (23:39 +0000)]
ARM: OMAP4/5: Make bootz as the default boot command
So with OMAP added to multi platform kernel,
the uImage no more contains a valid load address.
With the uboot already supporting zImage,
change the default boot command to bootz
instead.
projects / u-boot.git / log