arm: dts: k3-j721e-main: Update the speed modes supported and their itap delay values for MMCSD subsystems
According to latest errata of J721e [1], HS400 mode is not supported
in MMCSD0 subsystem (i2024) and SDR104 mode is not supported in MMCSD1/2
subsystems (i2090). Therefore, replace mmc-hs400-1_8v with mmc-hs200-1_8v
in MMCSD0 subsystem and add a sdhci mask to disable SDR104 speed mode.
Also, update the itap delay values for all the MMCSD subsystems according
the latest J721e data sheet[2]
test: pinmux: add test for 'pinctrl-single' driver
The test adds two pinmux nodes to the device tree, one to test when a
register changes only one pin's mux (pinctrl-single,pins), and the other
to test when more than one pin's mux is changed (pinctrl-single,bits).
This required replacing the controller's register access functions when
the driver is used on sandbox.
Signed-off-by: Dario Binacchi <dariobin@libero.it> Reviewed-by: Simon Glass <sjg@chromium.org>
It allows to display the muxing of a given pin. Inspired by more recent
versions of the Linux driver, in addition to the address and the value
of the configuration register I added the pin function retrieved from
the DT. In doing so, the information displayed does not depend on the
platform, being a generic type driver, and it can be useful for debug
purposes.
Signed-off-by: Dario Binacchi <dariobin@libero.it> Reviewed-by: Simon Glass <sjg@chromium.org>
The configuration of pinmux registers was implemented with duplicate
code which can be removed by adding two functions for read/write access.
Access to 8-bit registers has also been added.
Signed-off-by: Dario Binacchi <dariobin@libero.it> Reviewed-by: Simon Glass <sjg@chromium.org>
pinctrl: single: change function mask default value
The patch is inspired by more recent versions of the Linux driver.
Replacing the default value 0xffffffff of the function mask with 0 is
certainly more conservative in case the "pinctrl-single,function-mask"
DT property is missing.
Signed-off-by: Dario Binacchi <dariobin@libero.it> Reviewed-by: Simon Glass <sjg@chromium.org>
In more recent versions of the Linux kernel the driver's probe function
returns an error if the "pinctrl-single,register-width" DT property is
missing. The lack of this information, in fact, does not allow to know
whether to access the registers of the controller at 8, 16, ... bits.
Signed-off-by: Dario Binacchi <dariobin@libero.it> Reviewed-by: Simon Glass <sjg@chromium.org>
The dev_dbg(dev, " reg/val 0x%pa/0x%08x\n", ®, val); prints the 'reg'
address preceded by the prefix 0x0x instead of 0x. This because the
printf '%pa' format specifier already prepends the prefix '0x' to the
address displayed.
The pinmux configuration DT node of a peripheral does not define a
physical address but an offset. Only by adding it to the base address of
the controller it is possible to calculate the physical address of the
register to be configured. Printing an offset also requires a different
formatting option than a physical address.
pinctrl: single: fix the loop counter variable type
The 'n' variable is used as a loop counter, not as a physical address,
and is used in a comparison with an int. So it makes sense to change
its type from phys_addr_t to int.
Adam Ford [Sat, 13 Mar 2021 15:46:32 +0000 (09:46 -0600)]
configs: omap35_logic_somlv: Fix MMC booting
A previous patch had removed the GPIO nodes from being built
into the SPL Device tree, but CONFIG_SPL_GPIO_SUPPORT remained
which makes the MMC card detect fail and the board does not boot.
Fix this by disabling CONFIG_SPL_GPIO_SUPPORT.
Fixes: 6f1efe81aa84 ("configs: omap3/35_logic and omap3/35_logic_somlv: Reduce SPL size") Signed-off-by: Adam Ford <aford173@gmail.com>
Tom Rini [Sun, 4 Apr 2021 20:04:56 +0000 (16:04 -0400)]
sphinx: Pin to docutils-0.16
In newer docutils writers/latex2e/docutils.sty has a unicode character
in the comments which can in turn cause Python 3.6 at least to fail.
Pin to the previous docutils release for now.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Wed, 31 Mar 2021 22:18:13 +0000 (11:18 +1300)]
Makefile: Silence the deprecation script
This bash code is currently showing up in the build unless 'make -s' is
used. We don't normally show these sorts of things as they are confusing.
Also this code was not shown before the recent refactoring of how these
messages are displayed.
Add an '@' to silence it.
Suggested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Bin Meng <bmeng.cn@gmail.com> Fixes: 13732528516 ("Makefile: Add common code to report deprecation")
Andy Shevchenko [Thu, 11 Feb 2021 14:40:12 +0000 (16:40 +0200)]
test: Don't unmount not (yet) mounted system
When test suite tries to create a file for a new filesystem test case and fails,
the clean up of the exception tries to unmount the image, that has not yet been
mounted. When it happens, the fuse_mounted global variable is set to False and
inconveniently the test case tries to use sudo, so without this change the
admin of the machine gets an (annoying) email:
Subject: *** SECURITY information for example.com ***
example.com : Feb 5 19:43:47 : ... COMMAND=/bin/umount .../build-sandbox/persistent-data/mnt
and second run of the test cases on uncleaned build folder will ask for sudo
which is not what expected.
Besides that there is a double unmount calls during successfully run test case.
All of these due to over engineered Python try-except clause and people didn't
get it properly at all. The rule of thumb is that don't use more keywords than
try-except in the exception handling code. Nevertheless, here we adjust code
to be less intrusive to the initial logic behind that complex and unclear
constructions in the test case, although it adds a lot of lines of the code,
i.e. splits one exception handler to three, so on each step we know what
cleanup shall perform.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Thu, 25 Mar 2021 16:20:13 +0000 (16:20 +0000)]
sunxi: H616: Change TF-A load address to beginning of DRAM
Loading Trusted-Firmware's BL31 at 16KB into DRAM was originally a hack
to allow sharing more code with the other SoCs (which use this offset
in SRAM). However there is no longer a reason for that, as the
problematic macros have been properly separated there.
The latest (and hopefully final) TF-A code drop now changes the load
address to the beginning of DRAM, which is also more easily protected
by the Trustzone memory controller (code to be done).
Adjust the load address of BL31 now, to avoid any issues with
incompatible versions later on (the TF-A patches are about to be merged).
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Samuel Holland <samuel@sholland.org>
Jessica Clarke [Sat, 20 Mar 2021 20:43:05 +0000 (20:43 +0000)]
Support building on macOS/arm64
On Arm-based Macs, -no_pie is ignored and gives a linker warning.
Moreover, the build falls over with:
ld: Absolute addressing not allowed in arm64 code but used in '_image_type_ptr_aisimage' referencing '_image_type_aisimage'
for dumpimage and mkimage, since we put data structs in text sections
not data sections and so cannot have dynamic relocations. Instead, move
the sections to __DATA and drop disabling PIE.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Sean Anderson [Fri, 26 Mar 2021 02:02:28 +0000 (22:02 -0400)]
dm: test: Always include command.h for print_ut
We need this header for U_BOOT_CMD, which is always present even without
EFI.
Fixes: 82c468a049 ("dm: test: Update Makefile conditions") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 27 Mar 2021 17:53:08 +0000 (06:53 +1300)]
test: Add udevice declaration to avoid build error
When including this file on a board other than sandbox (e.g by enabling
UNIT_TEST and CMD_SETEXPR) an results. Fix it by declaring struct udevice
first.
Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Sat, 27 Mar 2021 15:58:37 +0000 (11:58 -0400)]
Merge branch '2021-03-27-master-imports'
- Rework the deprecation warnings to be consistently phrased.
- Add in a warning for DM_I2C, for a year from next release.
- Fix Azure builds of Windows host tools.
Tom Rini [Fri, 26 Mar 2021 19:14:14 +0000 (15:14 -0400)]
Azure: Use "pacman -Sy" to install the toolchain
We now see an error such as:
warning: database file for 'ucrt64' does not exist (use '-Sy' to download)
error: failed to prepare transaction (could not find database)
So use -Sy as suggested.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 25 Mar 2021 08:24:42 +0000 (21:24 +1300)]
Makefile: Use common code for DM_ETH deprecation warning
Update the CONFIG_DM_ETH check to use the 'deprecated' function.
Tested with snow
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:41 +0000 (21:24 +1300)]
Makefile: Use common code for WDT deprecation warning
Update the CONFIG_WDT check to use the 'deprecated' function.
Tested with kmcent2
Old message:
===================== WARNING ======================
This board does not use CONFIG_WDT (DM watchdog support).
Please update the board to use CONFIG_WDT before the
v2019.10 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_WDT (Driver Model
for DM watchdog). Please update the board to use
CONFIG_WDT before the v2019.10 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:40 +0000 (21:24 +1300)]
Makefile: Use common code for SPI_FLASH deprecation warning
Update the CONFIG_DM_SPI_FLASH check to use the 'deprecated' function.
Tested with vinco
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH (Driver Model
for SPI flash). Please update the board to use
CONFIG_DM_SPI_FLASH before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:39 +0000 (21:24 +1300)]
Makefile: Use common code for DM_VIDEO deprecation warning
Update the CONFIG_DM_VIDEO check to use the 'deprecated' function.
Tested with pxm2
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO (Driver Model
for video). Please update the board to use
CONFIG_DM_VIDEO before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
==================================================
Simon Glass [Thu, 25 Mar 2021 08:24:38 +0000 (21:24 +1300)]
Makefile: Use common code for PCI deprecation warning
Update the CONFIG_DM_PCI check to use the 'deprecated' function.
Tested with MPC8349ITX
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI (Driver Model
for PCI). Please update the board to use
CONFIG_DM_PCI before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:37 +0000 (21:24 +1300)]
Makefile: Use common code for LIBATA deprecation warning
Update the CONFIG_LIBATA check to use the 'deprecated' function.
Tested with MPC8349ITX
Old message:
===================== WARNING ======================
This board does use CONFIG_LIBATA but has CONFIG_AHCI not
enabled. Please update the storage controller driver to use
CONFIG_AHCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_AHCI (Driver Model
for AHCI). Please update the board to use
CONFIG_AHCI before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:36 +0000 (21:24 +1300)]
Makefile: Use common code for MVSATA_IDE deprecation warning
Update the CONFIG_MVSATA_IDE check to use the 'deprecated' function.
Tested with nas220
Old message:
===================== WARNING ======================
This board does use CONFIG_MVSATA_IDE which is not
ported to driver-model (DM) yet. Please update the storage
controller driver to use CONFIG_AHCI before the v2019.07
release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_AHCI (Driver Model
for AHCI instead of CONFIG_MVSATA_IDE). Please update the board to use
CONFIG_AHCI before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:35 +0000 (21:24 +1300)]
Makefile: Use common code for USB deprecation warning
Update the USB check to use the 'deprecated' function.
Tested with xpress
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB (Driver Model
for USB). Please update the board to use
CONFIG_DM_USB before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:34 +0000 (21:24 +1300)]
Makefile: Use common code for MMC deprecation warning
Update the MMC check to use the 'deprecated' function.
Tested with zc5202
Old message:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
New message:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC (Driver Model
for MMC). Please update the board to use
CONFIG_DM_MMC before the v2019.04 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Simon Glass [Thu, 25 Mar 2021 08:24:33 +0000 (21:24 +1300)]
Makefile: Add common code to report deprecation
Add a function which can be called to report a migration problem. This
will make it easier to add new migration checks, since the logic and
strings are not spread out over 8 lines of code.
Maxim Kochetkov [Fri, 12 Mar 2021 06:27:41 +0000 (09:27 +0300)]
mtd: rawnand: fsl_ifc: fix FSL NAND driver to read all ONFI parameter pages
Linux commit a75bbe71a27 ("mtd: rawnand: fsl_ifc: fix FSL NAND driver to
read all ONFI parameter pages")
Per ONFI specification (Rev. 4.0), if the CRC of the first parameter page
read is not valid, the host should read redundant parameter page copies.
Fix FSL NAND driver to read the two redundant copies which are mandatory
in the specification.
Signed-off-by: Jane Wan <Jane.Wan@nokia.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 11 Mar 2021 07:30:51 +0000 (15:30 +0800)]
pci: layerscape: Change to allocate zeroed memery for struct ls_pcie
As on some incipient Layerscape platforms (LS1043A series) there isn't
separate PF control register block, these registers reside in the LUT
register block, so when the driver detected there isn't 'ctrl', it will
assign the 'lut' address to the ls_pcie->ctrl.
The current code allocate memory for the struct ls_pcie with random
contents, this can result in skipping to assign the ls_pcie->ctrl with
the 'lut' address, then further crash with the incorrect address.
Fixes: 118e58e26eba ("pci: layerscape: Split the EP and RC driver") Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Chris Packham [Wed, 3 Mar 2021 01:09:46 +0000 (14:09 +1300)]
board: freescale: t208xrdb: Add link to User Guide
The User Guide contains handy things like block diagrams and DIP switch
settings and it's even available on the public web. Add a link to it in
the README.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Chris Packham [Wed, 3 Mar 2021 01:09:44 +0000 (14:09 +1300)]
rtc: ds1307: Add ds1339 compatible
As far as u-boot is concerned the ds1339 is compatible with the other
devices supported by the ds1307 driver. The Linux driver does expose
some additional functionality but as far as u-boot is concerned just
adding the compatible string is enough.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
fsl_ifc: fix typo in the NOR CSOR register definition
The name of the define must indicate 'Asynchronous', so 'ASYNC' is more
appropriate. AYSNC is probably a typo, and checkpatch script is throwing
a warning if this is set in the board include files.
It is save to change this now as none of the existing designs is using it
so far, but we will use it in our design it help to make IFC settings
more transparent.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
arm: socfpga: Only do 'is OS booted from FIT' checking when VAB is enabled
Check CONFIG_SOCFPGA_SECURE_VAB_AUTH before perform 'is OS booted from FIT'
checking in board_prep_linux function. And, fix typo of
CONFIG_SOCFPGA_SECURE_VAB_AUTH_ALLOW_NON_FIT_IMAGE.
CONFIG_FIT will be enabled in both ATF and VAB boot flow, thus,
board_prep_linux function will always be called by both ATF and
VAB boot flow.
board_pre_linux function will do 'is OS booted from FIT' checking,
and it will be called before board_fit_image_post_process function.
VAB boot flow expects the OS is always booted from FIT and with VAB
signed cerfiticate because the VAB authentication is implemented in
board_fit_image_post_process function. So, VAB needs the 'is OS booted
from FIT' checking in board_pre_linux function.
However, for ATF boot flow, it is not a requirement that the OS must
always booted from FIT. The OS can be booted from individual Image and
kernel dtb file. Thus, we should not do 'if OS is booted from FIT'
checking in board_prep_linux function.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
When uploading an EFI binary via the UART we need to assign a device path.
* Provide devicepath node to text conversion for Uart() node.
* Provide function to create Uart() device path.
* Add UART support to efi_dp_from_name().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Andre Przywara [Tue, 2 Mar 2021 15:43:43 +0000 (15:43 +0000)]
nvme: Elaborate on cache maintenance operation in get/set_features
At the moment the nvme_get_features() and nvme_set_features() functions
carry a (somewhat misleading) comment about missing cache maintenance.
As it turns out, nvme_get_features() has no caller at all in the tree,
and nvme_set_features' only user doesn't use a DMA buffer.
Mention that in the comment, and leave some breadcrumbs for the future,
should those functions attract more users.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andre Przywara [Mon, 8 Feb 2021 13:31:54 +0000 (13:31 +0000)]
nvme: Always invalidate whole cqes[] array
At the moment nvme_read_completion_status() tries to invalidate a single
member of the cqes[] array, which is shady as just a single entry is
not cache line aligned.
The structure is dictated by hardware, and with 16 bytes is smaller than
any cache line we usually deal with. Also multiple entries need to be
consecutive in memory, so we can't pad them to cover a whole cache line.
As a consequence we can only always invalidate all of them - U-Boot just
uses two of them anyway. This is fine, as they are only ever read by the
CPU (apart from the initial zeroing), so they can't become dirty.
Make this obvious by always invalidating the whole array, regardless of
the entry number we are about to read.
Also blow up the allocation size to cover whole cache lines, to avoid
other heap allocations to sneak in.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Marek Behún [Sat, 6 Mar 2021 22:43:22 +0000 (23:43 +0100)]
api: fix a potential serious bug caused by undef CONFIG_SYS_64BIT_LBA
The api_public.h header file undefined macro CONFIG_SYS_64BIT_LBA.
But api/api_storage.c includes this header before including part.h,
causing the type of lbaint_t and subsequently the type signature of
blk_dread() and blk_dwrite() functions to change from the rest of U-Boot
(if CONFIG_SYS_64BIT_LBA is defined for the board).
This is of course wrong, because the call to blk_dread() / blk_dwrite()
will receive mangled arguments.
Fix this by removing the undef of macro CONFIG_SYS_64BIT_LBA and instead
make the immediate code do what it would do as if the macro was not
defined.
Add a FIXME to whoever is maintaining this code.
CI managed to trigger this bug when compiling for lsxhl_defconfig, which
has CONFIG_API selected. The compiler complained about blk_dwrite() and
blk_dread() not matching original declarations:
include/blk.h:280:15: warning: type of ‘blk_dwrite’ does not match
original declaration
[-Wlto-type-mismatch]
280 | unsigned long blk_dwrite(struct blk_desc *block_dev, lbaint_t st
| ^
drivers/block/blk-uclass.c:456:15: note: type mismatch in parameter 2
456 | unsigned long blk_dwrite(struct blk_desc *block_dev, lbaint_t st
| ^
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Simon Glass <sjg@chromium.org>
Dario Binacchi [Tue, 16 Mar 2021 20:51:44 +0000 (21:51 +0100)]
bus: ti-sysc: change in a normal driver
The module defines a duplicate uclass driver for UCLASS_SIMPLE_BUS, but
it is not allowed. This breaks of-platdata and makes the result
non-deterministic.
The driver does not need to be an uclass driver, so lets remove it. I
had turned it into an uclass driver because I thought wrongly it had to
call the dm_scan_fdt_dev routine to work properly, but some tests on the
board have shown otherwise.
Signed-off-by: Dario Binacchi <dariobin@libero.it> Reviewed-by: Simon Glass <sjg@chromium.org>
Michael Walle [Wed, 17 Mar 2021 14:01:35 +0000 (15:01 +0100)]
board: sl28: disable HS400 mode
Since commit 8ee802f899ef ("mmc: fsl_esdhc: make sure delay chain locked
for HS400") HS400 mode is unreliable on LS1028A SoCs. Some workarounds are
missing for this SoC.
Frank Wunderlich [Tue, 16 Mar 2021 18:05:33 +0000 (19:05 +0100)]
ahci: mediatek: fix undefined reference of dev_err
building with MTK_AHCI enabled results in implicit declaration and
undefined reference of dev_err followed by a segfault of gcc
drivers/ata/mtk_ahci.c: In function 'mtk_ahci_parse_property':
drivers/ata/mtk_ahci.c:65:4: warning:
implicit declaration of function 'dev_err'
drivers/ata/mtk_ahci.c:65: undefined reference to `dev_err'
in function `mtk_ahci_probe':
drivers/ata/mtk_ahci.c:92: undefined reference to `dev_err'
Segmentation fault
fix this by adding the dm/device_compat.h to includes
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Tom Rini [Thu, 18 Mar 2021 16:53:35 +0000 (12:53 -0400)]
Merge branch '2021-03-17-assorted-fixes'
- Make tests search /sbin for tools, don't use ENODATA in host tools to
be more portable, avb fix when partition isn't found and a bugfix for
mediatek mmc.
Andy Shevchenko [Thu, 11 Feb 2021 14:40:09 +0000 (16:40 +0200)]
test: Include /sbin to the PATH when creating ext4 disk image
On some distributions the mkfs.ext4 is under /sbin and /sbin is not set
for mere users. Include /sbin to the PATH when creating ext4 disk image,
so that users won't get a scary traceback from Python.
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 24 Feb 2021 13:50:32 +0000 (08:50 -0500)]
image: Avoid -ENODATA in host tools
Unfortunately -ENODATA is not available in OpenBSD. Use -EBADMSG
instead, to indicate a missing timestamp.
Fixes: c5819701a3d image: Adjust the workings of fit_check_format() Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Daniel Golle [Mon, 15 Mar 2021 15:31:11 +0000 (15:31 +0000)]
mmc: mtk-sd: don't ignore max-frequency from device tree
commit e58e68d9 ("mmc: mtk-sd: assign plat->cfg.f_max with a correct value")
wrongly assumed that plat->cfg.f_max is always unset at the time
mscd_drv_probe() is run. This is not true in case max-frequency being
defined in device tree, as it is then already set by mmc_of_parse()
in msdc_of_to_plat().
Only set plat->cfg.f_max to the default maximum value in case it is
not already set to a sane value.
Fixes: e58e68d93e ("mmc: mtk-sd: assign plat->cfg.f_max with a correct value") Cc: Stefan Roese <sr@denx.de> Cc: Weijie Gao <weijie.gao@mediatek.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move README.dfu to doc/usage/dfu.rst and convert to reStructured text.
In the long run this page should be split into two. One for the overview
and one for the dfu command. UEFI capsule updates and dfutftp should be
integrated into the overview page.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Glass [Sun, 7 Feb 2021 21:27:02 +0000 (14:27 -0700)]
efi: Fix compiler warnings
This occur when building on Raspberry Pi 400 (32-bit ARM). Fix them.
Examples:
cmd/efidebug.c: In function ‘do_efi_capsule_update’:
cmd/efidebug.c:75:49: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
ret = EFI_CALL(RT->update_capsule(&capsule, 1, (u64)NULL));
^
include/efi_loader.h:104:9: note: in definition of macro ‘EFI_CALL’
typeof(exp) _r = exp; \
^~~
cmd/efidebug.c:75:49: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
ret = EFI_CALL(RT->update_capsule(&capsule, 1, (u64)NULL));
^
include/efi_loader.h:104:19: note: in definition of macro ‘EFI_CALL’
typeof(exp) _r = exp; \
^~~
In file included from include/common.h:20,
from lib/efi_loader/efi_capsule.c:9:
lib/efi_loader/efi_capsule.c: In function ‘efi_update_capsule’:
include/efi_loader.h:83:8: warning: format ‘%lu’ expects argument of type
‘long unsigned int’, but argument 10 has type ‘size_t’
{aka ‘unsigned int’} [-Wformat=]
debug("%sEFI: Entry %s(" format ")\n", __efi_nesting_inc(), \
^~~~~~~~~~~~~~~~~~
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
#define pr_fmt(fmt) fmt
^~~
include/log.h:229:2: note: in expansion of macro ‘log’
log(LOG_CATEGORY, LOGL_DEBUG, fmt, ##args); \
^~~
include/log.h:249:2: note: in expansion of macro ‘debug_cond’
debug_cond(_DEBUG, fmt, ##args)
^~~~~~~~~~
include/efi_loader.h:83:2: note: in expansion of macro ‘debug’
debug("%sEFI: Entry %s(" format ")\n", __efi_nesting_inc(), \
^~~~~
lib/efi_loader/efi_capsule.c:444:2: note: in expansion of macro ‘EFI_ENTRY’
EFI_ENTRY("%p, %lu, %llu\n", capsule_header_array, capsule_count,
^~~~~~~~~
lib/efi_loader/efi_capsule.c:444:19: note: format string is defined here
EFI_ENTRY("%p, %lu, %llu\n", capsule_header_array, capsule_count,
~~^
%u
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace (uintptr_t)NULL by 0. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ilias Apalodimas [Sat, 13 Mar 2021 21:47:32 +0000 (23:47 +0200)]
efi_selftest: Remove loadfile2 for initrd selftests
We are redefining how u-boot locates the initrd to load via the kernel
LoadFile2 protocol. This selftest is not relevant any more, so remove
it. A new one will be added later
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Glass [Sun, 7 Feb 2021 21:27:01 +0000 (14:27 -0700)]
mkeficapsule: Correct printf() strings
Use %z when printing size_t values. This avoids errors on 32-bit
machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use a conversion to size_t for printing stat.st_size. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Mark Kettenis [Sun, 14 Mar 2021 19:04:24 +0000 (20:04 +0100)]
efi_loader: fix memory type for memory reservation block
The (yet unreleased version of the) devicetree specification clearly
states that:
As with the /reserved-memory node, when booting via UEFI
entries in the Memory Reservation Block must also be listed
in the system memory map obtained via the GetMemoryMap() toi
protect against allocations by UEFI applications. The memory
reservation block entries should be listed with type
EfiReservedMemoryType.
This restores the behaviour that was changed by commit 4cbb2930bd8c
("efi_loader: consider no-map property of reserved memory").
Fixes: 4cbb2930bd8c ("efi_loader: consider no-map property of reserved memory") Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: disable GRUB_ARM32_WORKAROUND on ARCH_SUNXI
GRUB_ARM32_WORKAROUND can be disabled on ARCH_SUNXI as the Allwinner SoCs
only have a level 2 cache controlled via CP15 and not an architecturally
defined cache. Having the cache available speeds up booting Linux.
On ARCH_BCM283X it is already disabled via rpi_2_defconfig. But let's move
this setting to Kconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Mon, 15 Mar 2021 12:43:19 +0000 (08:43 -0400)]
Merge tag 'u-boot-stm32-20210312' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Add WATCHDOG_RESET() in MTD framework and STM32 QSPI driver
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
Adam Ford [Sat, 6 Mar 2021 02:48:50 +0000 (20:48 -0600)]
ARM: da850-evm: Fix boot issues from missing SPL_PAD_TO
In a previous attempt to unify config options and remove items
from the whitelist file, SPL items were moved into a section
enabled with CONFIG_SPL_BUILD. Unfortunately, SPL_PAD_TO
is referenced at the head Makefile and uses this define
to create padding of the output file. When it was moved
to CONFIG_SPL_BUILD, it caused boot errors with devices
that are not booting from NOR. Fix the boot issues by moving
SPL_PAD_TO out so it's always.
Fixes: 7bb33e4684aa ("ARM: da850-evm: Unify config options with Kconfig") Signed-off-by: Adam Ford <aford173@gmail.com>
- Some more updates/sync's to A38x DDR3 code (Marek & Pali)
- marvell/ddr/AXP: Some type fixes found in the LTO work (Marek)
- Espressobin: Enable more options (Pali)
- pci-aardvark: Implement workaround for the readback value of
VEND_ID (Paili)
Patrice Chotard [Wed, 24 Feb 2021 12:53:27 +0000 (13:53 +0100)]
arm: stm32mp: Fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled
Fix following compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS
are enabled :
arch/arm/mach-stm32mp/cpu.c: In function ‘early_enable_caches’:
arch/arm/mach-stm32mp/cpu.c:223:10: error: ‘volatile struct arch_global_data’ has no member named ‘tlb_size’
223 | gd->arch.tlb_size = PGTABLE_SIZE;
| ^
arch/arm/mach-stm32mp/cpu.c:224:10: error: ‘volatile struct arch_global_data’ has no member named ‘tlb_addr’
224 | gd->arch.tlb_addr = (unsigned long)&early_tlb;
| ^
Patrice Chotard [Wed, 24 Feb 2021 12:38:20 +0000 (13:38 +0100)]
board: st: Remove board_early_init_f and board_late_init callbacks for stm32 boards
Remove board_early_init_f() and board_late_init() callbacks for stm32
boards as the corresponding flags (CONFIG_BOARD_LATE_INIT and
CONFIG_BOARD_EARLY_INIT_R) are now disabled.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrice Chotard [Wed, 24 Feb 2021 12:38:19 +0000 (13:38 +0100)]
configs: stm32: Remove BOARD_EARLY_INIT_F and BOARD_LATE_INIT for stm32 boards
These flags was defined and callbacks linked to these flags are empty
and only returning 0.
Remove BOARD_EARLY_INIT_F and BOARD_LATE_INIT flags for these stm32 boards.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
projects / u-boot.git / log