Simon Glass [Thu, 31 Oct 2019 13:42:50 +0000 (07:42 -0600)]
patman: Adjust 'command' to return strings instead of bytes
At present all the 'command' methods return bytes. Most of the time we
actually want strings, so change this. We still need to keep the internal
representation as bytes since otherwise unicode strings might break over
a read() boundary (e.g. 4KB), causing errors. But we can convert the end
result to strings.
Add a 'binary' parameter to cover the few cases where bytes are needed.
Simon Glass [Sun, 27 Oct 2019 15:47:41 +0000 (09:47 -0600)]
mx6: tbs2910: Minimise libfdt code size
This board appears to be very near its size limit and cannot accept the
new checking code in libfdt. Disable this code so this the board can
continue to build.
Simon Glass [Sun, 27 Oct 2019 15:47:40 +0000 (09:47 -0600)]
fdt: Add Kconfig options to control code size
For better or worse libfdt recent grew a lot of code that checks the
validity of the device tree in great detail. When using unsigned or
unverified data this makes things safer, but it does add to code size.
Add some controls to select the trade-off between safety and code size.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sun, 27 Oct 2019 15:47:39 +0000 (09:47 -0600)]
fdt: Add INT32_MAX to kernel.h for libfdt
Unfortunately libfdt needs this value now, which is present in the
stdint.h header. That file is just a placeholder in U-Boot and these sorts
of constants appear in the linux/kernel.h header instead.
To keep libfdt happy, add INT32_MAX too.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
- i.MX NAND: nandbcb support for MX6UL / i.MX7
- i.MX8: support for HAB
- Convert to DM (opos6ul, mccmon6)
- Toradex i.MX6ull colibri
- sync DTS with kernel
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[trini: Add <dm/ofnode.h> to provide the prototype to ofnode] Signed-off-by: Tom Rini <trini@konsulko.com>
- Add support for Intel FSP-S and FSP-T in binman
- Correct priority selection for image loaders for SPL
- Add a size check for TPL
- Various small SPL/TPL bug fixes and changes
- SPI: Add support for memory-mapped flash
Tom Rini [Sat, 2 Nov 2019 18:43:06 +0000 (14:43 -0400)]
tbs2910: Disable Plan9/RTEMS bootm support
We have once again reached a point where this board does not build in
some cases with supported toolchains due to reaching a size constraint.
To regain some space, disable support for Plan 9 / RTEMS images with the
bootm command.
Acked-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
Igor Opaniuk [Sun, 3 Nov 2019 15:49:46 +0000 (16:49 +0100)]
imx: nandbcb: add support for writing BCB only
Add subcommand for add writing BCB only, where we provide appropriate
offsets for firmware1 and firmware2 and size.
Example of usage:
> nandbcb bcbonly 0x00180000 0x00080000 0x00200000
Writing 1024 bytes to 0x0: randomizing
OK
Writing 1024 bytes to 0x20000: randomizing
OK
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Tested-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Igor Opaniuk [Sun, 3 Nov 2019 15:49:43 +0000 (16:49 +0100)]
nand: mxs_nand: add API for switching different BCH layouts
On i.MX7 in a sake of reducing the disturbances caused by a neighboring
cells in the FCB page in the NAND chip, a randomizer is enabled when
reading the FCB page by ROM bootloader.
Add API for setting BCH to specific layout (and restoring it back) used by
ROM bootloader to be able to burn it in a proper way to NAND using
nandbcb command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee> Tested-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Igor Opaniuk [Sun, 3 Nov 2019 15:49:42 +0000 (16:49 +0100)]
imx: gpmi: add defines for hw randominizer
Extend GPMI Integrated ECC Control Register Description, include
additional defines for enabling randomizer function and providing
proper randomizer type.
For additional details check i.MX7 APR, section
9.6.6.3 GPMI Integrated ECC Control Register Description
(GPMI_ECCCTRLn)
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Tested-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Tom Rini [Sun, 3 Nov 2019 12:41:12 +0000 (07:41 -0500)]
tbs2910: Disable Plan9/RTEMS bootm support
We have once again reached a point where this board does not build in
some cases with supported toolchains due to reaching a size constraint.
To regain some space, disable support for Plan 9 / RTEMS images with the
bootm command.
Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stefano Babic <sbabic@denx.de>
Ye Li [Sat, 26 Oct 2019 14:24:03 +0000 (16:24 +0200)]
mach-imx: Adding new argument for SIP call interface
Need to pass total 5 arguments for SIP HAB call on i.MX8MQ,
so update the interface to add new argument.
Signed-off-by: Ye Li <ye.li@nxp.com>
[agust: fixed imx8m-power-domain build] Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Patrick Wildt <patrick@blueri.se> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 25 Sep 2019 08:11:14 +0000 (08:11 +0000)]
imx8: Add AHAB secure boot support
Add function and new command "auth_cntr" for secure boot support.
When booting with life cycle set to OEM closed, we need to use
this function to authenticate the OS container and load kernel & FDT
from OS container to their destination.
Also add image authentication call when loading container images.
Users can set CONFIG_AHAB_BOOT=y to enable the feature. It is not
set at default.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 16 Oct 2019 10:24:39 +0000 (10:24 +0000)]
imx8m: evk: spl: probe clk in spl early stage
We are going to add i2c pmic support before dram could be used.
So we need enable clk driver earlier, so use spl_early_init
and move clock controller probe eariler to board_init_f.
Peng Fan [Wed, 16 Oct 2019 10:24:17 +0000 (10:24 +0000)]
imx8m: imx8mq: get chip rev for B1 revision
The i.MX8MQ B1 uses OCOTP_HW_OCOTP_READ_FUSE_DATA register for chip id.
It returns a magic number 0xff0055aa. update get_cpu_rev to support it,
and enable ocotp clock to access ocotp.
Patrick Wildt [Mon, 14 Oct 2019 11:19:00 +0000 (13:19 +0200)]
imx: update i.MX8MQ device trees
This updates the i.MX8MQ device trees and, necessarily, also the
i.MX8MQ clock bindings. These are taken verbatim from from the
Linux kernel version v5.4-rc2, which three small changes which
were already part of the previous device tree:
* Keep the PSCI reserved memory range
* Keep the alias for ethernet, so that the MAC address can be set
* Keep the modified #include for the IOMUXC pins
Signed-off-by: Patrick Wildt <patrick@blueri.se> Acked-by: Peng Fan <peng.fan@nxp.com>
Lukasz Majewski [Tue, 15 Oct 2019 08:28:45 +0000 (10:28 +0200)]
spl: nor: Provide falcon boot support for NOR memories
This commit adds falcon boot support (by also copying args necessary for
booting) to the SPL NOR memory driver.
After this change it is possible to use the falcon boot in the same way
as on NAND memories. The necessary configs (i.e. CONFIG_CMD_SPL_NOR_OFS)
are now defined in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
Lukasz Majewski [Tue, 15 Oct 2019 08:28:44 +0000 (10:28 +0200)]
ARM: imx: Decouple mccmon6's SPL and u-boot proper code
The mccmon6 has been used a "mixed" approach between SPL and
U-Boot proper sources.
This commit decoupes SPL and u-boot proper, which allows clear
distinction between those two code bases and facilitates
conversion to DM/DTS on this particular board.
Robert Hancock [Tue, 6 Aug 2019 17:05:30 +0000 (11:05 -0600)]
watchdog: imx: Use immediate reset bits for expire_now
The expire_now function was previously setting the watchdog timeout to
minimum and waiting for the watchdog to expire. However, this watchdog
also has bits to trigger immediate reset. Use those instead, like the
Linux imx2_wdt driver does.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Robert Hancock [Tue, 6 Aug 2019 17:05:29 +0000 (11:05 -0600)]
watchdog: imx: Add DT ext-reset handling
The Linux imx2_wdt driver uses a fsl,ext-reset-output boolean in the
device tree to specify whether the board design should use the external
reset instead of the internal reset. Use this boolean to determine which
mode to use rather than using external reset unconditionally.
For the legacy non-DM mode, the external reset is always used in order
to maintain the previous behavior.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Marek Vasut [Tue, 15 Oct 2019 16:26:57 +0000 (18:26 +0200)]
arm: mxs: Increase VDDD voltage to match specification
According to IMX28CEC rev. 4, 10/2018, Table 15. Recommended Operating
Conditions, page 16, the VDDD should be set to 1.55V when the CPU is
operating at 454MHz. This is the case in U-Boot, hence increase the
VDDD voltage. This fixes instability when performing TFTP transfers.
Increase the brownout threshold to 1.4V. The documentation recommends
1.45V setting for the brownout, however, this triggers failure during
power block init, so keep the brownout slightly lower.
Claudius Heine [Tue, 29 Oct 2019 12:08:43 +0000 (13:08 +0100)]
ARM: imx: Fix bmode detection from grp10
imx6_is_bmode_from_gpr9 always returns false, because
IMX6_SRC_GPR10_BMODE is 1<<28 and gets casted to u8 on return.
This moves the function body into imx6_src_get_boot_mode, since that is the
only one using it and it is on the same abstraction level (accessing
registers directly).
Lukasz Majewski [Mon, 14 Oct 2019 15:43:34 +0000 (17:43 +0200)]
imx: defconfig: Enable CONFIG_SPL_FORCE_MMC_BOOT on display5
After the following commit:
commit 772b55723bcb ("imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC
boot on falcon mode")
it is possible to set the CONFIG_SPL_FORCE_MMC_BOOT flag, which allows
using MMC device as boot device regardless of the device used by Boot ROM
(FBL) as the first boot medium.
Display5 board needs this flag set to allow falcon boot from eMMC device.
net: ti: am65x-cpsw: fix mac tx internal delay for rgmii-rxid mode
Now AM65x CPSW2G driver will disable MAC TX internal delay for PHY
interface mode "rgmii-rxid" which is incorrect. Hence, fix it by keeping
default value (enabled) for MAC TX internal delay when "rgmii-rxid"
interface mode is selected.
net: ti: cpsw: enable 10Mbps link speed support in rgmii mode
According to TRMs the 10Mbps link speed is supported in RGMII only when
CPSW2G MAC SL is configured for External Control ("in band") mode
CPSW_SL_MACCTRL.EXT_EN(18) = 1.
Hence update cpsw_slave_update_link() to follow documentation.
Simon Glass [Mon, 21 Oct 2019 03:37:55 +0000 (21:37 -0600)]
x86: Move CPU init to before spl_init()
At present we call spl_init() before identifying the CPU. This is not a
good idea - e.g. if bootstage is enabled then it will try to set up the
timer which works better if the CPU is identified.
Put explicit code at each entry pointer to identify the CPU.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 21 Oct 2019 03:37:50 +0000 (21:37 -0600)]
x86: tpl: Add a fake PCI bus
In TPL we try to minimise code size so do not include the PCI subsystem.
We can use fixed BARs and drivers can directly program the devices that
they need.
However we do need to bind the devices on the PCI bus and without PCI this
does not ordinarily happen. As a work-around, define a fake PCI bus which
does this binding, but no other PCI operations. This is a convenient way
to ensure that we can use the same device tree for TPL, SPL and U-Boot
proper:
TPL - CONFIG_TPL_PCI is not set (no auto-config, fake PCI bus)
SPL - CONFIG_SPL_PCI is set (no auto-config but with real PCI bus)
U-Boot - CONFIG_PCI is set (full auto-config after relocation)
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 21 Oct 2019 03:37:49 +0000 (21:37 -0600)]
x86: spl: Support init of a PUNIT
The x86 power unit handles power management. Support initing this device
which is modelled as a new type of system controller since there are no
operations needed.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 21 Oct 2019 03:37:47 +0000 (21:37 -0600)]
x86: timer: Use a separate flag for whether timer is inited
At present the value of the timer base is used to determine whether the
timer has been set up or not. It is true that the timer is essentially
never exactly 0 when it is read. However 'time 0' may indicate the time
that the machine was reset so it is useful to be able to denote that.
Update the code to use a separate flag instead.
Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 21 Oct 2019 03:31:47 +0000 (21:31 -0600)]
spi: Add support for memory-mapped flash
On x86 platforms the SPI flash can be mapped into memory so that the
contents can be read with normal memory accesses.
Add a new SPI method to find the location of the SPI flash in memory. This
differs from the existing device-tree "memory-map" mechanism in that the
location can be discovered at run-time.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 21 Oct 2019 03:31:45 +0000 (21:31 -0600)]
spl: Correct priority selection for image loaders
At present the name of the image comes first in the linker-list symbol
used. This means that the name of the function sets the sort order, which
is not the intention.
Update it to put the boot-device type first, then the priority. This
produces the expected behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Mon, 21 Oct 2019 03:31:34 +0000 (21:31 -0600)]
binman: Correct symbol calculation with non-zero image base
At present binman adds the image base address to the symbol value before
it writes it to the binary. This is not correct since the symbol value
itself (e.g. image position) has no relationship to the image base.
Fix this and update the tests to cover this case.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With the __packed attribute sandbox_defconfig cannot be compiled with GCC
9.2.1:
fs/cbfs/cbfs.c: In function ‘file_cbfs_fill_cache’:
fs/cbfs/cbfs.c:164:16: error: taking address of packed member of
‘struct cbfs_cachenode’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
164 | cache_tail = &new_node->next;
| ^~~~~~~~~~~~~~~
struct cbfs_cachenode is only an internal structure. So let's rearrange the
fields such that the structure is naturally packed and remove the __packed
attribute.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 1 Nov 2019 21:49:40 +0000 (17:49 -0400)]
Merge tag 'arc-fixes-for-2020.01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-arc
ARC fixes for v2020.01-rc2
The main change is move to DM_MMC of yet 2 another ARC boards:
AXS101 & IoTDK.
Among that we improve handling of stock-formatted SD-cards of high volume
on EM SDP as well as introduction of reset driver for HSDK which is required
for prepser reinitialization of some peripherals like USB etc.
Tom Rini [Fri, 1 Nov 2019 17:59:14 +0000 (13:59 -0400)]
azure: Update the script to prepend PATH not override PATH
Similar to 90d3d78a1c68 ("gitlab-ci: Prepend to PATH rather than replace
it") we need to prepend the PATH with our additional binaries and not
replace the value fully as doing so breaks virtualenv.
Alexey Brodkin [Wed, 9 Oct 2019 07:18:18 +0000 (10:18 +0300)]
arc: emsdp: docs: Prefer Degilent over Opella-XD
Back in the day on early board samples built-in Digilent JTAG probe
was not functional so we used externally attached Ashling Opella-XD
probe. But now with production units everything works as expected and
so we anybody may enjoy readily avaialble built-in JTAG probe so
we specify Digilent oprion on MDB's command line example.
Alexey Brodkin [Tue, 8 Oct 2019 10:25:30 +0000 (13:25 +0300)]
arc: emsdp: Increase max FAT cluster size
Some especially large SD-cards come from stock formatted with
larger FAT cluster size so to accommodate those we just increase
what we expect to have here in U-Boot given we have a plenty of
space on EM SDP (16 MiB).
Sam Protsenko [Mon, 21 Oct 2019 10:55:16 +0000 (13:55 +0300)]
cmd: avb: Support A/B slots
Add optional parameter to 'avb verify' sub-command, so that user is able
to specify which slot to use, in case when user's partitions are
slotted. If that parameter is omitted, the behavior of 'avb verify' will
be the same as before, so user API is content.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com> Acked-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Sam Protsenko [Thu, 15 Aug 2019 17:49:47 +0000 (20:49 +0300)]
cmd: avb: Fix requested partitions list
The requested_partitions[] array should contain only boot partitions.
Usually it's only 'boot' partition, as can be seen in [1]. Also, seems
like the requested_partitions[] are only used when there is no 'vbmeta'
partition [2], which is not a regular use-case.
Make requested_partitions[] contain only 'boot' partition as it was
supposed to be, and also make that array to be a local in
do_avb_verify_part() function, as nobody else needs that.
projects / u-boot.git / log