]> git.dujemihanovic.xyz Git - u-boot.git/log
u-boot.git
5 years agoarmv8: ls2088aqds: Add bootcmd for TFA boot
Wasim Khan [Mon, 10 Jun 2019 10:17:25 +0000 (10:17 +0000)]
armv8: ls2088aqds: Add bootcmd for TFA boot

Add bootcmd for IFC NOR boot and SD boot.

Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarm: ls1028a: define the integrated PCI bus (ECAM)
Alex Marginean [Fri, 7 Jun 2019 14:03:07 +0000 (17:03 +0300)]
arm: ls1028a: define the integrated PCI bus (ECAM)

LS1028A includes an integrated PCI bus with 11 PCI functions residing on
bus 0.  ECAM plus the device register space takes up 256MB of address
space.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: fsl-lsch2: add clock support for the second eSDHC
Yinbo Zhu [Mon, 3 Jun 2019 11:24:23 +0000 (19:24 +0800)]
armv8: fsl-lsch2: add clock support for the second eSDHC

Layerscape began to use two eSDHC controllers, for example,
LS1012A. They are same IP block with same reference clock.
This patch is to add clock support for the second eSDHC.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoconfigs/ls1046ardb_*: disable CONFIG_SPI_FLASH_USE_4K_SECTORS
Maciej Pijanowski [Fri, 31 May 2019 20:30:58 +0000 (22:30 +0200)]
configs/ls1046ardb_*: disable CONFIG_SPI_FLASH_USE_4K_SECTORS

With this setting enabled, the on-board QSPI cannot be
properly flashed. There are no error messages, but the simple
write / read / compare tests fail.

This is already disabled in the qspi and tfa defconfigs for the
LS1046ARDB platform.

Signed-off-by: Maciej Pijanowski <maciej.pijanowski@3mdeb.com>
Cc: piotr.krol@3mdeb.com
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarm: fsl-layerscape: add 0x3040 serdes1 settings for LS1046A
Maciej Pijanowski [Fri, 31 May 2019 14:11:35 +0000 (16:11 +0200)]
arm: fsl-layerscape: add 0x3040 serdes1 settings for LS1046A

Signed-off-by: Maciej Pijanowski <maciej.pijanowski@3mdeb.com>
Cc: piotr.krol@3mdeb.com
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarm: fsl-layerscape: fix 0x3363 serdes1 settings for ls1046a
Maciej Pijanowski [Fri, 31 May 2019 14:00:26 +0000 (16:00 +0200)]
arm: fsl-layerscape: fix 0x3363 serdes1 settings for ls1046a

As per LS1046A hardware manual, SGMII.9 and SGMII.10 present on
lane D and lane C respectively for 0x3363 protocol.

So fix serdes1 settings for ls1046a.

Signed-off-by: Maciej Pijanowski <maciej.pijanowski@3mdeb.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoconfigs: Unset CONFIG_SPI_FLASH_BAR, move CONFIG_FSL_QSPI to defconfig
Ashish Kumar [Fri, 31 May 2019 10:33:28 +0000 (16:03 +0530)]
configs: Unset CONFIG_SPI_FLASH_BAR, move CONFIG_FSL_QSPI to defconfig

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: fsl-layerscape: fix config dependency for layerscape pci code
Alex Marginean [Thu, 30 May 2019 16:28:31 +0000 (19:28 +0300)]
armv8: fsl-layerscape: fix config dependency for layerscape pci code

Fixes a link error on layerscape platform, linking fails with CONFIG_PCI
set and CONFIG_PCI_LAYERSCAPE unset.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: fsl-layerscape: Change bootcmd update logic
Pankit Garg [Thu, 30 May 2019 12:04:15 +0000 (12:04 +0000)]
armv8: fsl-layerscape: Change bootcmd update logic

Change bootcmd update logic when CONFIG_ENV_ADDR is not defined

Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agols1046ardb: Add CONFIG_ENV_ADDR to init env in qspi boot
Pankit Garg [Thu, 30 May 2019 12:04:14 +0000 (12:04 +0000)]
ls1046ardb: Add CONFIG_ENV_ADDR to init env in qspi boot

Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: fsl-layerscape: Update qspi clk cfg
Pankit Garg [Wed, 29 May 2019 12:12:36 +0000 (12:12 +0000)]
armv8: fsl-layerscape: Update qspi clk cfg

Update qspi clock configuration in TFABOOT in case
of all boot sources except qspi boot source.

Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoARM: dts: ls1021a: Fixed reg for sata node
Peng Ma [Wed, 29 May 2019 02:40:47 +0000 (02:40 +0000)]
ARM: dts: ls1021a: Fixed reg for sata node

This patch is to fixed the reg read to "0" for armv7
architecture.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8/fsl-layerscape: Add loop to check L3 dcache status
Meenakshi Aggarwal [Tue, 28 May 2019 16:07:58 +0000 (21:37 +0530)]
armv8/fsl-layerscape: Add loop to check L3 dcache status

Flushing L3 cache may need variable time depending upon cache line
allocation.

Coming up with a proper timeout value would be best handled by
simulations under multiple scenarios in your actual system.
>From the purely HN-F point of view, the flush would take ~15 cycles for
a clean line, and ~22 cycles for a dirty line.  For the dirty line case,
there are many variables outside the HN-F that will increase the
duration per line.  For example, a *DBIDResp from the SN-F/SBSX,
memory controller latency, SN-F/SBSX RetryAck responses, CCN ring
congestion, CCN ring hops, etc, etc.  The worst-case timeout would
have to factor in all of these variables plus the HN-F cycles for
every line in the L3, and assuming all lines are dirty

In case if L3 is not flushed properly, system behaviour will be
erratic, so remove timeout and add loop to check status of L3 cache.

System will stuck in while loop if there is some issue in L3 cache
flushing.

Signed-off-by: Udit Kumar <udit.kumar@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: lx2160aqds: Enable eSDHC controllers
Yinbo Zhu [Mon, 27 May 2019 04:17:18 +0000 (12:17 +0800)]
armv8: lx2160aqds: Enable eSDHC controllers

This patch is to enable esdhc controllers for lx2160aqds

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: ls1028a: Add secure boot defconfig
Yuantian Tang [Fri, 24 May 2019 06:36:27 +0000 (14:36 +0800)]
armv8: ls1028a: Add secure boot defconfig

Add secure boot defconfig for ls1028aqds and ls1028ardb boards.

Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoboard: lx2160a: use default scan_dev_for_boot
Mian Yousaf Kaukab [Thu, 23 May 2019 08:57:34 +0000 (10:57 +0200)]
board: lx2160a: use default scan_dev_for_boot

Default environment variable is more complete. Also scans for efi
binaries for example.

Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoboard: lx2160a: fix fsl-mc status in fdt with bootefi
Mian Yousaf Kaukab [Thu, 23 May 2019 08:57:33 +0000 (10:57 +0200)]
board: lx2160a: fix fsl-mc status in fdt with bootefi

fsl-mc lazyapply command applies dpl from efi_exit_boot_services().
Status of fsl-mc node in working fdt is updated at this stage.
However, an efi application like grub may already have copied the fdt.
So the updates to fdt done at efi_exit_boot_services() may not be
visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply
command is used.

Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: ls1028a: Add ecc address node for sata.
Peng Ma [Thu, 23 May 2019 04:06:48 +0000 (04:06 +0000)]
armv8: ls1028a: Add ecc address node for sata.

Move the ecc addr from driver to dts

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agommc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled
Yangbo Lu [Thu, 23 May 2019 03:05:46 +0000 (11:05 +0800)]
mmc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled

u-boot is trying to make CONFIG_BLK as a hard requirement
for DM_MMC. But now it's still not.

config BLK
bool "Support block devices"
depends on DM
default y if DM_MMC

When fsl_esdhc driver was reworked for DM_MMC support, DM_MMC
without CONFIG_BLK enabled wasn't considered. This patch is to
fix probe issue without CONFIG_BLK enabled.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: fsl-lsch3: add clock support for the second eSDHC
Yangbo Lu [Thu, 23 May 2019 03:05:45 +0000 (11:05 +0800)]
armv8: fsl-lsch3: add clock support for the second eSDHC

Layerscape began to use two eSDHC controllers, for example,
LS1028A. They are same IP block with same reference clock.
This patch is to add clock support for the second eSDHC.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: lx2160aqds: Enable sata
Peng Ma [Wed, 22 May 2019 02:43:22 +0000 (02:43 +0000)]
armv8: lx2160aqds: Enable sata

Change sata node status to enable sata.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: ls1028a: Add other serdes protocal support
Xiaowei Bao [Tue, 21 May 2019 10:28:31 +0000 (18:28 +0800)]
armv8: ls1028a: Add other serdes protocal support

Add other serdes protocal support.

Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: ls1028a: enable workaround for USB errarum A-009007
Yinbo Zhu [Tue, 14 May 2019 09:34:57 +0000 (17:34 +0800)]
armv8: ls1028a: enable workaround for USB errarum A-009007

Rx Compliance tests may fail intermittently at high jitter
frequencies using default register values.

So program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoarmv8: ls1028a: enable workaround for USB erratum A-008997
Ran Wang [Tue, 14 May 2019 09:34:56 +0000 (17:34 +0800)]
armv8: ls1028a: enable workaround for USB erratum A-008997

Enable workaround for USB erratum A-008997. Here PCSTXSWINGFULL
registers has been moved to DSCR as compared to other Layerscape SoCs
where it was in SCFG.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoboard/fsl/layerscape: Modify the aliases names
Pankaj Bansal [Mon, 22 Apr 2019 06:31:42 +0000 (06:31 +0000)]
board/fsl/layerscape: Modify the aliases names

when compiling dts file using DTC_FLAG='-@', the device tree compiler
reports these warnings:

Warning (alias_paths): /aliases: aliases property name must include
only lowercase and '-'

Fixed the node aliases to silence these warnings.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
5 years agoMerge tag 'efi-2019-07-rc5-2' of git://git.denx.de/u-boot-efi
Tom Rini [Sat, 15 Jun 2019 17:03:00 +0000 (13:03 -0400)]
Merge tag 'efi-2019-07-rc5-2' of git://git.denx.de/u-boot-efi

Pull request for UEFI sub-system for v2019.07-rc5 (2)

This pull request provides bug fixes for the UEFI sub-system. The most
relevant one concerns the allocation of memory at address 0. It is
needed for booting Linux on several boards via bootefi, e.g. the Asus
TinkerBoard.

An undefined reference bug in disk/part.c related to a division is
resolved.

5 years agoMerge branch 'master' of git://git.denx.de/u-boot-socfpga
Tom Rini [Sat, 15 Jun 2019 17:02:26 +0000 (13:02 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga

- SPL size check for Gen5, i2c enablement for S10

5 years agoMerge branch 'master' of git://git.denx.de/u-boot-sh
Tom Rini [Sat, 15 Jun 2019 17:02:12 +0000 (13:02 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-sh

- More board removal

5 years agoMerge branch '2019-06-14-master-imports'
Tom Rini [Sat, 15 Jun 2019 16:58:06 +0000 (12:58 -0400)]
Merge branch '2019-06-14-master-imports'

- Kconfig migrations of SPL_BOOT_xxx, SYS_LDSCRIPT, IP_DEFRAG,
  TFTP_BLOCKSIZE.
- Typo fixes, other minor corrections.

5 years agocmd: define CMD_DATA_SIZE when CONFIG_CMD_SETEXPR is selected
Bartosz Golaszewski [Mon, 20 May 2019 08:22:14 +0000 (10:22 +0200)]
cmd: define CMD_DATA_SIZE when CONFIG_CMD_SETEXPR is selected

The setexpr shell command calls cmd_get_data_size() which is only built
when CMD_DATA_SIZE is defined. We need to define CMD_DATA_SIZE if
CONFIG_CMD_SETEXPR is selected or the build will fail if no other
command selecting this option is enabled.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
5 years agoconfigs: Migrate CONFIG_SYS_LDSCRIPT to Kconfig
Tom Rini [Sun, 2 Jun 2019 12:57:32 +0000 (08:57 -0400)]
configs: Migrate CONFIG_SYS_LDSCRIPT to Kconfig

In order to migrate this symbol to Kconfig introduce a new symbol to
guard it, CONFIG_SYS_CUSTOM_LDSCRIPT.  When that is set we can then
provide the exact final location o the script.

Signed-off-by: Tom Rini <trini@konsulko.com>
5 years agoconfigs: Remove unneeded CONFIG_SYS_LDSCRIPT instances
Tom Rini [Sun, 2 Jun 2019 12:57:31 +0000 (08:57 -0400)]
configs: Remove unneeded CONFIG_SYS_LDSCRIPT instances

A number of boards set CONFIG_SYS_LDSCRIPT and then end up using one of
the default searched LDSCRIPT paths.  Remove these customizations.

Signed-off-by: Tom Rini <trini@konsulko.com>
5 years agoconfigs: Migrate the various SPL_BOOT_xxx choices for PowerPC
Tom Rini [Sat, 1 Jun 2019 18:20:25 +0000 (14:20 -0400)]
configs: Migrate the various SPL_BOOT_xxx choices for PowerPC

The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a
choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and
CONFIG_SPL_SPI_BOOT.  Migrate this to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
5 years agocommon: Fix a typo abnove -> above
Andy Shevchenko [Wed, 12 Jun 2019 12:35:24 +0000 (15:35 +0300)]
common: Fix a typo abnove -> above

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
5 years agotools: add tools/spl_size_limit to ignore list
Simon Goldschmidt [Tue, 11 Jun 2019 20:18:51 +0000 (22:18 +0200)]
tools: add tools/spl_size_limit to ignore list

This tool has just been added but it seems I forgot to add it to
the ignore list. So to prevent the built binary being marked as
unversioned, add it to the ignore list.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
5 years agonet: Convert CONFIG_TFTP_BLOCKSIZE to Kconfig
Marek Vasut [Tue, 11 Jun 2019 02:51:15 +0000 (04:51 +0200)]
net: Convert CONFIG_TFTP_BLOCKSIZE to Kconfig

Convert CONFIG_TFTP_BLOCKSIZE to Kconfig, update defconfigs,
headers and whitelist.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
5 years agonet: Convert CONFIG_IP_DEFRAG to Kconfig
Marek Vasut [Tue, 11 Jun 2019 02:51:14 +0000 (04:51 +0200)]
net: Convert CONFIG_IP_DEFRAG to Kconfig

Convert CONFIG_IP_DEFRAG to Kconfig, update defconfigs, headers
and whitelist. This patch is a follow-up on a patch by Christian
Gmeiner with the added config/header/whitelist updates.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
5 years agoefi_loader: fix SetAttribute()
Heinrich Schuchardt [Fri, 14 Jun 2019 05:16:57 +0000 (07:16 +0200)]
efi_loader: fix SetAttribute()

The SetAttribute() service and the Reset() service of the simple text
output protocol must update the attribute value in the mode information.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoefi_loader: fix SetMode()
Heinrich Schuchardt [Fri, 14 Jun 2019 05:20:51 +0000 (07:20 +0200)]
efi_loader: fix SetMode()

Correct the check of the mode number in SetMode() service of the simple
text output protocol.

Clear the screen in SetMode().

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoefi_loader: GetTime() must return EFI_UNSUPPORTED
Heinrich Schuchardt [Thu, 13 Jun 2019 16:42:40 +0000 (18:42 +0200)]
efi_loader: GetTime() must return EFI_UNSUPPORTED

If the GetTime() runtime service is not supported, EFI_UNSUPPORTED has to
be returned.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoefi_loader: add RuntimeServicesSupported variable
AKASHI Takahiro [Wed, 5 Jun 2019 04:21:38 +0000 (13:21 +0900)]
efi_loader: add RuntimeServicesSupported variable

This variable is defined in UEFI specification 2.8, section 8.1.
Its value should be updated whenever we add any usable runtime services
function.

Currently we only support SetVirtualAddress() for all systems and
ResetSystem() for some.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoefi_loader: parameter checks SetVariable()
Heinrich Schuchardt [Wed, 12 Jun 2019 21:28:42 +0000 (23:28 +0200)]
efi_loader: parameter checks SetVariable()

Return EFI_INVALID_PARAMETER if the variable name has zero length or the
variable has runtime access but not boottime access.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agodisk: part: avoid undefined reference to `__udivmoddi4'
Heinrich Schuchardt [Sat, 1 Jun 2019 22:04:50 +0000 (00:04 +0200)]
disk: part: avoid undefined reference to `__udivmoddi4'

When compiling with FTRACE=1 an error

ld.bfd: disk/built-in.o: in function `lba512_muldiv':
disk/part.c:114: undefined reference to `__udivmoddi4

occurred.

Use '>> 11' instead of '/ 2048' to avoid the division.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoefi_loader: legal characters in StrToFat()
Heinrich Schuchardt [Wed, 12 Jun 2019 19:06:28 +0000 (21:06 +0200)]
efi_loader: legal characters in StrToFat()

The UEFI specification does not specify if the characters that have to be
replaced by underscore in function StrToFat() of the Unicode collation
protocol are those forbidden in FAT long names or those in FAT short names.
EDK2 and UEFI SCT assume it is those forbidden in FAT 8.3 short names.

Adjust the list of forbidden characters.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoefi_loader: MetaiMatch() must be case insensitive
Heinrich Schuchardt [Wed, 12 Jun 2019 17:18:24 +0000 (19:18 +0200)]
efi_loader: MetaiMatch() must be case insensitive

The MetaiMatch() service of the UnicodeCollationProtocol2 must be case
insensitive.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoefi_loader: AllocatePages() must accept addr == 0
Heinrich Schuchardt [Wed, 12 Jun 2019 05:17:04 +0000 (07:17 +0200)]
efi_loader: AllocatePages() must accept addr == 0

It must be possible to allocate memory at address 0 with AllocatePages().

Move a NULL pointer check.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoefi_loader: correct ExitBootServices()
Heinrich Schuchardt [Tue, 11 Jun 2019 18:05:40 +0000 (20:05 +0200)]
efi_loader: correct ExitBootServices()

Always use EFI_EXIT() to return from the function.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoefi_loader: loaded images cannot be started twice
Heinrich Schuchardt [Tue, 11 Jun 2019 17:35:20 +0000 (19:35 +0200)]
efi_loader: loaded images cannot be started twice

If an image already has been started, return EFI_INVALID_PARAMETER when
StartImage() is called for the same handle again.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoefi_loader: LoadImage must return EFI_NOT_FOUND
Heinrich Schuchardt [Tue, 11 Jun 2019 17:00:56 +0000 (19:00 +0200)]
efi_loader: LoadImage must return EFI_NOT_FOUND

If the file path does not relate to an existing file, LoadImage() must
return EFI_NOT_FOUND.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoefi_loader: LoadImage w/o SourceBuffer and DevicePath
Heinrich Schuchardt [Tue, 11 Jun 2019 16:52:33 +0000 (18:52 +0200)]
efi_loader: LoadImage w/o SourceBuffer and DevicePath

If both SourceBuffer and DevicePath are NULL, LoadImage() must return
EFI_INVALID_PARAMETER.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
5 years agoMAINTAINERS: change Ramon Fried email address
Ramon Fried [Thu, 6 Jun 2019 18:35:05 +0000 (21:35 +0300)]
MAINTAINERS: change Ramon Fried email address

Change my email address, too many mails
gets to my private mail, created specific email
account just for developmement.

Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
5 years agosh: r0p7734: Remove the board
Marek Vasut [Mon, 20 May 2019 01:28:00 +0000 (03:28 +0200)]
sh: r0p7734: Remove the board

Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
5 years agosh: ap325rxa: Remove the board
Marek Vasut [Mon, 20 May 2019 01:27:27 +0000 (03:27 +0200)]
sh: ap325rxa: Remove the board

Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
5 years agosh: ap_sh4a_4a: Remove the board
Marek Vasut [Mon, 20 May 2019 01:21:39 +0000 (03:21 +0200)]
sh: ap_sh4a_4a: Remove the board

Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
5 years agosh: ms7750se: Remove the board
Marek Vasut [Mon, 20 May 2019 01:19:44 +0000 (03:19 +0200)]
sh: ms7750se: Remove the board

Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
5 years agosh: ms7722: Remove the board
Marek Vasut [Mon, 20 May 2019 01:18:46 +0000 (03:18 +0200)]
sh: ms7722: Remove the board

Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
5 years agosh: espt_giga: Remove the board
Marek Vasut [Mon, 20 May 2019 01:16:27 +0000 (03:16 +0200)]
sh: espt_giga: Remove the board

Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
5 years agoarm: socfpga: provide default SPL_SIZE_LIMIT for gen5
Simon Goldschmidt [Thu, 13 Jun 2019 19:50:28 +0000 (21:50 +0200)]
arm: socfpga: provide default SPL_SIZE_LIMIT for gen5

This provides an SPL_SIZE_LIMIT that makes the build check that the SPL
binary loaded from flash fits into the SRAM (64 KiB) and leaves enough
room for global data, heap  and stack (512 bytes assumed stack usage).

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
5 years agoarm: dts: Stratix10: Enable i2c
Ley Foon Tan [Thu, 13 Jun 2019 08:17:23 +0000 (16:17 +0800)]
arm: dts: Stratix10: Enable i2c

Enable i2c1 in Stratix 10 devkit.

SOCFPGA_STRATIX10 # i2c bus
Bus 0:  i2c@ffc02900
SOCFPGA_STRATIX10 # i2c dev 0
Setting bus to 0
SOCFPGA_STRATIX10 # i2c probe
Valid chip addresses: 14 4C 51 68 74

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
5 years agoMerge tag 'u-boot-amlogic-20190612' of git://git.denx.de/u-boot-amlogic
Tom Rini [Wed, 12 Jun 2019 19:28:34 +0000 (15:28 -0400)]
Merge tag 'u-boot-amlogic-20190612' of git://git.denx.de/u-boot-amlogic

- pinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groups
- pinctrl: meson-gxbb: add hdmi related pins to fix HDMI on GXBB
- pinctrl: meson: add support for getting pinmux status
- pinctrl: meson-g12a: add support for drive-strength-microamp property

5 years agoMerge tag 'efi-2019-07-rc5' of git://git.denx.de/u-boot-efi
Tom Rini [Wed, 12 Jun 2019 11:15:38 +0000 (07:15 -0400)]
Merge tag 'efi-2019-07-rc5' of git://git.denx.de/u-boot-efi

Pull request for UEFI sub-system for v2019.07-rc5

This pull request provides fixes for event services.

5 years agopinctrl: meson-gxbb: add hdmi related pins
Maxime Jourdan [Tue, 4 Jun 2019 20:26:37 +0000 (22:26 +0200)]
pinctrl: meson-gxbb: add hdmi related pins

The GXBB pinctrl is missing pins related to HDMI, namely hot plug
detection (hpd) and I2C (sda + scl).

This fixes HDMI support for GXBB in u-boot.

Reported-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
5 years agopinctrl: meson: g12a: add DS bank value
Guillaume La Roque [Tue, 4 Jun 2019 11:53:08 +0000 (13:53 +0200)]
pinctrl: meson: g12a: add DS bank value

add drive-strength bank regiter and bit value for G12A SoC

Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
5 years agopinctrl: meson: add support of drive-strength-microamp
Guillaume La Roque [Tue, 4 Jun 2019 11:53:07 +0000 (13:53 +0200)]
pinctrl: meson: add support of drive-strength-microamp

drive-strength-microamp is a new feature needed for G12A SoC.
the default DS setting after boot is usually 500uA and it is not enough for
many functions. We need to be able to set the drive strength to reliably
enable things like MMC, I2C, etc ...

Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
5 years agodm: pinctrl: Add driver-strength-microamp property
Guillaume La Roque [Tue, 4 Jun 2019 11:53:06 +0000 (13:53 +0200)]
dm: pinctrl: Add driver-strength-microamp property

Add drive-strength-microamp property support to allow drive strength in uA

Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
5 years agopinctrl: meson-axg: add support for getting pinmux status
Neil Armstrong [Tue, 4 Jun 2019 09:04:54 +0000 (11:04 +0200)]
pinctrl: meson-axg: add support for getting pinmux status

In order to support the "pinmux status" command, use the common functions
to get the pins count and names, and add the AXG specific function to get
the current function from registers.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
5 years agopinctrl: meson-gx: add support for getting pinmux status
Neil Armstrong [Tue, 4 Jun 2019 09:04:53 +0000 (11:04 +0200)]
pinctrl: meson-gx: add support for getting pinmux status

In order to support the "pinmux status" command, use the common functions
to get the pins count and names, and add the GX specific function to get
the current function from registers.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
5 years agopinctrl: meson: add common function to get pins name
Neil Armstrong [Tue, 4 Jun 2019 09:04:52 +0000 (11:04 +0200)]
pinctrl: meson: add common function to get pins name

In order to support the "pinmux status" command, add common function
to get pins count and pin name.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
5 years agopinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groups
Neil Armstrong [Tue, 4 Jun 2019 09:04:51 +0000 (11:04 +0200)]
pinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groups

The GPIO_TEST_N was in the wrong pmx group table, move it back with the AO
groups, GPIODV_18 was missing, add it back, and finally the GPIOCLK_*
group names were missing.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
5 years agoMerge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot
Tom Rini [Tue, 11 Jun 2019 21:22:22 +0000 (17:22 -0400)]
Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot

- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board

5 years agoMerge tag 'u-boot-imx-20190612' of git://git.denx.de/u-boot-imx
Tom Rini [Tue, 11 Jun 2019 17:41:24 +0000 (13:41 -0400)]
Merge tag 'u-boot-imx-20190612' of git://git.denx.de/u-boot-imx

u-boot-imx-20190612
--------------------

- Board fixes:
- imx6logic
- wandboard
- mx6sabre boots again
- imx8qm_mek
- pico-* boards
- Toradex apalis / colibri
- engicam imx6 (environment)
- KP MX53
- opos6ul
- Switch to DM:
- vining2000
- dh MX6
- Toradex colibri i.MX7
- Novena
- Security : fix CSF size for HAB
- Other:
      - imx: fix building for i.mx8 without spl
      - pcie and switch to DM

      mx6sabreauto: Enable SPL SDP support

5 years agoconfigs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT
Heinrich Schuchardt [Wed, 27 Feb 2019 19:05:43 +0000 (20:05 +0100)]
configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT

The SPL for the Tinker Board has to fit into 32 KiB. Currently this limit
is exceeded.

CONFIG_SPL_I2C_SUPPORT is not needed to move to main U-Boot. So let's
disable it.

Suggested-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
5 years agospl: imx6: Provide a SPL_SIZE_LIMIT default
Fabio Estevam [Sat, 8 Jun 2019 17:56:44 +0000 (14:56 -0300)]
spl: imx6: Provide a SPL_SIZE_LIMIT default

As explained in include/configs/imx6_spl.h. the i.MX6 SPL
size limit is 68KB (4KB header + 64KB max size).

Provide such limit for all i.MX6 boards that use SPL
to detect SPL size overflow in build time.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
5 years agomx6sabreauto: Enable SPL SDP support
Sjoerd Simons [Tue, 4 Jun 2019 19:56:28 +0000 (21:56 +0200)]
mx6sabreauto: Enable SPL SDP support

To allow loading u-boot over USB enable SDP support in the SPL.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
5 years agomx6sabreauto: Remove CONFIG_SPL_DM to decrease the SPL size
Sjoerd Simons [Tue, 4 Jun 2019 19:56:27 +0000 (21:56 +0200)]
mx6sabreauto: Remove CONFIG_SPL_DM to decrease the SPL size

The i.mx6 SPL binary cannot be bigger then 68K, while with the current
defconfig for sabreauto it's only about 56K as soon as USB support gets
added the size will overflows.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
5 years agoarm: dts: imx6qdl-u-boot: Alias usb0 to usbotg
Sjoerd Simons [Tue, 4 Jun 2019 13:49:58 +0000 (15:49 +0200)]
arm: dts: imx6qdl-u-boot: Alias usb0 to usbotg

All i.mx6 boards seems to have moved to DM_USB, however gadget support
for mx6 is still pre-DM as CI_UDC isn't converted yet. To make this work
the usb otg controller used for gadgets needs to be usb number 0.
Add an alias for this directly in the main u-boot mx6qdl dtsi so it
doesn't need to be done for each board separately.

This fixes regressions wrt. usb gadget functionality in several boards
that have gadget functions enabled in their config, but no usb0 alias in
their device-tree.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
5 years agomx6sabreauto: set SYS_MALLOC_F for video
Sjoerd Simons [Tue, 4 Jun 2019 13:49:57 +0000 (15:49 +0200)]
mx6sabreauto: set SYS_MALLOC_F for video

Sabre Auto boards currently hang with:
```
U-Boot 2019.07-rc3-00057-gc41940c406 (Jun 03 2019 - 14:42:41 +0200)

CPU:   Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz)
CPU:   Automotive temperature grade (-40C to 125C)Reset cause: WDOG
Model: Freescale i.MX6 Quad Plus SABRE Automotive Board
Board: MX6Q-Sabreauto revA
I2C:   ready
DRAM:  2 GiB
Video device 'ipu@2400000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Video device 'ipu@2800000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Some drivers failed to bind
Error binding driver 'generic_simple_bus': -28
Some drivers failed to bind
initcall sequence 8ffe00b8 failed at call 1780e93b (err=-28)
```

Set SYS_MALLOC_F_LEN to reserve_video to work.

This is similar to the change Peng Fan did for mx6sabresd (9002e735e717)

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
5 years agomx6sabreauto: Select pinctrl driver
Sjoerd Simons [Tue, 4 Jun 2019 13:49:56 +0000 (15:49 +0200)]
mx6sabreauto: Select pinctrl driver

With the conversion to DM we should select the pinctrl driver.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
5 years agoimx8mq_evk: Staticize when appropriate
Fabio Estevam [Sat, 18 May 2019 16:18:45 +0000 (13:18 -0300)]
imx8mq_evk: Staticize when appropriate

Staticize 'spl_dram_init' and 'i2c_pad_info1' to fix the
following sparse warnings:

board/freescale/imx8mq_evk/spl.c:30:6: warning: symbol 'spl_dram_init' was not declared. Should it be static?
board/freescale/imx8mq_evk/spl.c:41:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static?

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
5 years agoimx: define ARCH_MXC for i.MX8/8M/7ULP
Peng Fan [Thu, 9 May 2019 08:33:55 +0000 (08:33 +0000)]
imx: define ARCH_MXC for i.MX8/8M/7ULP

Without this definition, fsl_esdhc will access reserved registers
on i.MX chips, so define ARCH_MXC to fix it.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
5 years agoimx: drop imx-regs.h
Peng Fan [Thu, 9 May 2019 08:33:52 +0000 (08:33 +0000)]
imx: drop imx-regs.h

imx-regs.h under arch-imx has no user, drop it.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
5 years agoimx8: cpu: get temperature when print cpu desc
Peng Fan [Fri, 26 Apr 2019 01:44:27 +0000 (01:44 +0000)]
imx8: cpu: get temperature when print cpu desc

Read the temperature when print cpu inforation.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
5 years agopinctrl: imx: Define imx6_pinctrl_soc_info in .data section
Lukasz Majewski [Tue, 23 Apr 2019 14:44:51 +0000 (16:44 +0200)]
pinctrl: imx: Define imx6_pinctrl_soc_info in .data section

This commit is necessary to be able to re-use the pinctrl code in early
SPL to properly configure pins.

The problem is that those "static" structures (without explicit
initialization) are placed in the SDRAM area, which corresponds to
u-boot proper (not even SPL).
Hence, when one wants to configure pins before relocation via DTS/DM,
the board hangs (imx6q SoC powered one) as only OCRAM area is available
(0x009xxxxx).

This commit prevents from this issue by moving the imx6_pinctrl_soc_info
structure to data section (from BSS).

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
5 years agonet: fec_mxc: not access reserved register on i.MX8
Peng Fan [Mon, 15 Apr 2019 05:18:33 +0000 (05:18 +0000)]
net: fec_mxc: not access reserved register on i.MX8

We should not access reserved register on i.MX8, otherwise met SERROR

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
5 years agoARM: imx: vining2000: Enable DM Serial
Marek Vasut [Fri, 17 May 2019 20:25:28 +0000 (22:25 +0200)]
ARM: imx: vining2000: Enable DM Serial

Enable DM Serial support on iMX6SX VINING|2000.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
5 years agoARM: imx: vining2000: Enable DM PCI
Marek Vasut [Fri, 17 May 2019 20:25:27 +0000 (22:25 +0200)]
ARM: imx: vining2000: Enable DM PCI

Enable DM PCI support on iMX6SX VINING|2000.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
5 years agoARM: imx: vining2000: Enable DM GPIO
Marek Vasut [Fri, 17 May 2019 20:25:26 +0000 (22:25 +0200)]
ARM: imx: vining2000: Enable DM GPIO

Enable DM GPIO support on iMX6SX VINING|2000 and fix up
board code where applicable.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
5 years agoARM: imx: vining2000: Enable DM USB
Marek Vasut [Fri, 17 May 2019 20:25:25 +0000 (22:25 +0200)]
ARM: imx: vining2000: Enable DM USB

Enable DM USB support on iMX6SX VINING|2000.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
5 years agoARM: imx: vining2000: Convert MMC and block to DM
Marek Vasut [Fri, 17 May 2019 20:25:24 +0000 (22:25 +0200)]
ARM: imx: vining2000: Convert MMC and block to DM

Enable DM block and DM MMC support on iMX6SX VINING|2000 .
Convert board code to match the DM support. This disables
USB mass storage support due to missing DM USB, however
that will be re-enabled in subsequent patch.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
5 years agoARM: imx: vining2000: Enable DM pin control
Marek Vasut [Fri, 17 May 2019 20:25:23 +0000 (22:25 +0200)]
ARM: imx: vining2000: Enable DM pin control

Enable DM pin control support on iMX6SX VINING|2000.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
5 years agoARM: dts: imx: vining2000: Import VINING|2000 DT from Linux
Marek Vasut [Fri, 17 May 2019 20:25:22 +0000 (22:25 +0200)]
ARM: dts: imx: vining2000: Import VINING|2000 DT from Linux

Import iMX6SX VINING|2000 device tree from Linux 5.1.1 b724e9356404 .
Enable DT control in full U-Boot .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
5 years agoARM: imx: Rename VINING|2000
Marek Vasut [Fri, 17 May 2019 20:25:21 +0000 (22:25 +0200)]
ARM: imx: Rename VINING|2000

The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
5 years agomx6sx: vining2000: pinmux usdhc4 reset
Christoph Fritz [Fri, 17 May 2019 19:19:31 +0000 (21:19 +0200)]
mx6sx: vining2000: pinmux usdhc4 reset

This patch configures pinmux for pin usdhc4 reset.

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
5 years agoMAINTAINERS: Add imx dts files to i.MX maintainers list
Fabio Estevam [Fri, 10 May 2019 12:23:53 +0000 (09:23 -0300)]
MAINTAINERS: Add imx dts files to i.MX maintainers list

Add imx dts files to the MAINTAINERS file list, so that i.MX
devicetree related patches can be properly sent to the i.MX folks.

Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
5 years agoserial: mxc: Add iMX6SX compatible string
Marek Vasut [Fri, 17 May 2019 19:56:40 +0000 (21:56 +0200)]
serial: mxc: Add iMX6SX compatible string

Add compatible string for iMX6SX.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
5 years agoARM: imx: novena: Enable DM PCI
Marek Vasut [Fri, 17 May 2019 18:32:19 +0000 (20:32 +0200)]
ARM: imx: novena: Enable DM PCI

Enable DM PCI support on iMX6Q Novena.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
5 years agopci: imx: Add DM and DT support
Marek Vasut [Sun, 9 Jun 2019 01:50:55 +0000 (03:50 +0200)]
pci: imx: Add DM and DT support

Add DM support and support for probing the iMX PCI driver from DT.
The legacy non-DM support is retained, however shall be removed once
DM PCI is the only option remaining.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
5 years agopci: imx: Pass driver private data around
Marek Vasut [Sun, 9 Jun 2019 01:50:54 +0000 (03:50 +0200)]
pci: imx: Pass driver private data around

Pass the driver private data around the driver as much as possible, instead
of having it as a static global variable. This is done in preparation for
the DM conversion, no functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
5 years agopci: imx: Fix potential 64bit memory access clamping
Marek Vasut [Sun, 9 Jun 2019 01:50:53 +0000 (03:50 +0200)]
pci: imx: Fix potential 64bit memory access clamping

The driver limits the config space base to 32bit, however it can be
64bit on 64bit iMX hardware too. Remove that limitation. This patch
has no impact on the iMX6, which is the only SoC currently supported
by this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
5 years agopci: imx: Factor out hard-coded register base addresses
Marek Vasut [Sun, 9 Jun 2019 01:50:52 +0000 (03:50 +0200)]
pci: imx: Factor out hard-coded register base addresses

Pull out hard-coded register base addresses into driver private
structure in preparation for DM conversion. No functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>