Hai Pham [Thu, 26 Jan 2023 20:05:55 +0000 (21:05 +0100)]
mmc: renesas-sdhi: R-Car M3 r1.3 also uses 4 tuning taps
Early ES revisions of M3-W SoCs requires 4-tap HS400. Reflect the status
from datasheet.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Thu, 26 Jan 2023 20:02:05 +0000 (21:02 +0100)]
clk: renesas: Drop core param from gen3_clk_get_rate64_pll_mul_reg
Drop 'core' parameter from gen3_clk_get_rate64_pll_mul_reg() function
as it is only used in debug print. No functional change except for the
debug print, which is disabled by default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Hai Pham [Thu, 26 Jan 2023 20:02:04 +0000 (21:02 +0100)]
clk: renesas: Use pre-defined offset for RPC clocks
Since commit f7b4e4c0949f ("clk: renesas: Synchronize R-Car Gen3 tables
with Linux 5.12"), the custom macros for RPC clocks were dropped.
Use pre-defined offset for RPC clocks, same as what Linux does, instead
of retrieving it from the macros
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Thu, 26 Jan 2023 20:02:03 +0000 (21:02 +0100)]
clk: renesas: Add and enable CPG reset driver
Add trivial reset driver extension to the CPG clock driver. The change
turns current CPG UCLASS_CLK driver instance into an UCLASS_NOP proxy
driver, which in turn binds both generic rcar3_clk UCLASS_CLK clock
driver as well as generic rcar_rst UCLASS_RESET reset driver to the
CPG DT node. This way, any other drivers which use the 'reset' DT
property can now obtain valid reset handle backed by a reset driver.
The clock tables have been updated to represent the CPG driver and only
implement the generic CPG proxy driver bind call, which binds the clock
and reset drivers.
The DM_RESET is now enabled for all R-Car Gen3 platforms.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Hai Pham [Thu, 26 Jan 2023 20:02:02 +0000 (21:02 +0100)]
clk: renesas: r8a7796: Add R8A77961 CPG/MSSR support
Add support for the R-Car M3-W+ (R8A77961) SoC.
R-Car M3-W+ is very similar to R-Car M3-W (R8A77960), which allows for
both SoCs to share a driver.
Based on Linux commit 2ba738d56db4 ("clk: renesas: r8a7796: Add R8A77961
CPG/MSSR support")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Hai Pham [Thu, 26 Jan 2023 20:02:01 +0000 (21:02 +0100)]
clk: renesas: Rename CLK_R8A7796 to CLK_R8A77960
Rename CONFIG_CLK_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_CLK_R8A77960, to avoid confusion with R-Car M3-W+ (R8A77961),
which will use CONFIG_CLK_R8A77961.
Based on Linux commit 92d1ebae9abf ("clk: renesas: Rename CLK_R8A7796
to CLK_R8A77960")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename CLK_TYPE_R8A779A0_ to CLK_TYPE_GEN4_ to match the new
clock tables. Add CLK_TYPE_GEN4_SD, CLK_TYPE_GEN4_RPC and
CLK_TYPE_GEN4_RPCD2 macros and handling into Gen3 CPG core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Hai Pham [Thu, 26 Jan 2023 20:01:49 +0000 (21:01 +0100)]
clk: renesas: Add dummy SDnH clock
Currently, SDnH is handled together with SDn. This caused lots of
problems, so we want SDnH as a separate clock. Introduce a dummy SDnH
type here which creates a fixed-factor clock with factor 1. That allows
us to convert the per-SoC CPG drivers while keeping the old behaviour
for now. A later patch then will add the proper functionality.
Based on Linux series by Wolfram Sang:
commit a31cf51bf6b4b ("clk: renesas: rcar-gen3: Add dummy SDnH clock"),
commit 1abd04480866c ("clk: renesas: rcar-gen3: Add SDnH clock"),
commit 63494b6f98f26 ("clk: renesas: r8a779a0: Add SDnH clock to V3U")
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Switch to gen3_clk_get_rate64
Hai Pham [Thu, 26 Jan 2023 20:01:48 +0000 (21:01 +0100)]
pinctrl: renesas: r8a7796: Add R8A77961 PFC support
R-Car M3-W+ (R8A77961) is pin compatible with R-Car M3-W (R8A77960),
which allows for both SoCs to share a driver.
Based on Linux commit 708c69e9eacc ("pinctrl: sh-pfc: r8a7796: Add
R8A77961 PFC support") and 74ce7a8044b0 ("pinctrl: renesas: r8a7796:
Optimize pinctrl image size for R8A774A1")
Parts picked from
pinctrl: renesas: Synchronize R-Car Gen2/Gen3 tables with Linux 5.18.3
- Add pin groups for the green and high8 subsets of the Video IN pins
- Add MediaLB pins
- Add bias support for various SoCs
- Share more pin group data, to reduce size and ease review
- Miscellaneous cleanups, fixes and improvements.
This contains port of Linux kernel commit 6210905586ae ("pinctrl: renesas: Add shorthand for reserved register fields")
to handle negative entries in GROUP() macros correctly.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This is only a copyright and SPDX identifier update, no
functional change.
The following script has been used for the synchronization:
$ for i in $(cd include/dt-bindings/clock/ ; ls -1 r8a*) ; do cp /linux-2.6/include/dt-bindings/clock/$i include/dt-bindings/clock/ ; done
$ for i in $(cd include/dt-bindings/power/ ; ls -1 r8a*) ; do cp /linux-2.6/include/dt-bindings/power/$i include/dt-bindings/power/ ; done
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Mario Kicherer [Wed, 1 Feb 2023 06:16:22 +0000 (14:16 +0800)]
armv7: ls102xa: make QSPI clock selection optional during SoC init
To improve startup times when booting from QSPI flash, the QSPI frequency
can be configured very early in the boot process [1] to reduce loading
times of U-Boot itself. This patch adds an option to disable setting the
frequency to a default value during SoC initialization.
Manoj Sai [Mon, 28 Nov 2022 11:45:31 +0000 (17:15 +0530)]
configs: imx8mp_evk: revert to old ram settings
The 'commit 864ac2cf383e ("board: imx8mp: Add Engicam
i.Core MX8M Plus EDIMM2.2 Starter Kit")' has changed the imx8mp evk ram
settings from 6GB ram to 2GB.
This changeset reverts the above change.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reported-by : Peter Bergin <peter@berginkonsult.se> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
Arnaud Ferraris [Thu, 15 Dec 2022 14:51:17 +0000 (15:51 +0100)]
imx8mq_pins: fix configuration for UART4 on ECSPI2 pads
When routing UART4 using the ECSPI2 pads, register
IOMUXC_UART4_RXD_SELECT_INPUT (offset 0x050C) should be changed only
when dealing with RX, as its name suggests.
Ye Li [Tue, 13 Dec 2022 04:08:02 +0000 (05:08 +0100)]
imx8: scu_api: sync sc_rm_is_pad_owned api change
SCFW has fixed a overflow issue in sc_rm_is_pad_owned API. This
requires u-boot to update API implementation, since it will cause
compatible issue. Otherwise all pad checking will have problem and
cause pad setting not continue.
Due to the compatible issue, the new u-boot only works with new
SCFW (API version: 1.21 and later).
old scfw + old u-boot: API overflow issue
old scfw + new u-boot, or new scfw + old u-boot: API compatible issue
new scfw + new u-boot: Working
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Jason Liu <Jason.hui.liu@nxp.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Adam Ford [Sat, 19 Nov 2022 19:30:08 +0000 (13:30 -0600)]
configs: imx8mn_beacon_fspi: Add config for booting from QSPI
The imx8mn-beacon SOM has a QSPI part on it connected to the
FlexSPI controller. Add a defconfig option which supports
booting from the QSPI NOR flash instead of sd/mmc.
Tim Harvey [Fri, 11 Nov 2022 16:03:07 +0000 (08:03 -0800)]
board: gateworks: venice: poll I2C lines to wait for GSC firmware
In some situations the GSC firmware where the EEPROM containing the
model and DRAM configuration may not be ready by the time the SoC
is ready to talk to it over I2C.
Instead of a hard delay, poll the I2C lines to wait until they are
released to avoid the I2C drivers 'Arbitation lost' error message.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
Tom Rini [Tue, 31 Jan 2023 15:15:39 +0000 (10:15 -0500)]
Merge tag 'u-boot-amlogic-20230131' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- jethub j100: add rescue boot from microSD
- move meson sm command to cmd/meson and add efusedump sub-command
- switch dwc2 otg to DM for G12A, GXL & AXG
- Add new boards:
- Odroid Go Ultra
- Odroid-N2L
Max Krummenacher [Mon, 30 Jan 2023 12:39:06 +0000 (13:39 +0100)]
ARM: arm: colibri-imx6ull-emmc: fix emmc access
Synchronizing the device tree with linux introduced a regression.
The U-Boot specific dtsi mustn't override the alias settings for
the eMMC/SD interfaces.
Without this U-Boot cannot access the eMMC and boot the kernel.
Fixes: c21b61bff15 ("colibri-imx6ull/-emmc: synchronise device tree with linux") Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Implement basic PSCI provider to let OS turn CPU cores off and on,
power off and restart the system and determine PSCI version. This
is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following Kconfig options:
# CONFIG_PSCI_RESET is not set
CONFIG_ARMV8_MULTIENTRY=y
CONFIG_ARMV8_SET_SMPEN=y
CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y
CONFIG_ARMV8_EA_EL3_FIRST=y
CONFIG_ARMV8_PSCI=y
CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4
CONFIG_ARMV8_SECURE_BASE=0x970000
CONFIG_ARM_SMCCC=y
CONFIG_SYS_HAS_ARMV8_SECURE_BASE=y
Marek Vasut [Thu, 22 Dec 2022 00:46:42 +0000 (01:46 +0100)]
arm: imx: imx8m: Program CSU and TZASC if PSCI provider
In case U-Boot is the PSCI provider, it is necessary to correctly
program CSU and TZASC registers. Those are poorly documented, so
push in the correct values.
Marek Vasut [Thu, 22 Dec 2022 00:46:41 +0000 (01:46 +0100)]
arm: imx: imx8m: Define trampoline location if PSCI provider
The common code used to bring up secondary cores requires a final
jump location to be stored in some sort of memory location, define
this memory location to be the start of OCRAM, since it is available.
Marek Vasut [Thu, 22 Dec 2022 00:46:40 +0000 (01:46 +0100)]
arm: imx: imx8m: Map RAM as NS if PSCI provider
In case U-Boot is a PSCI provider, map RAM explicitly as NS,
otherwise secondary cores crash with SError when attempting
to access RAM mapped as secure in EL2.
Marek Vasut [Thu, 22 Dec 2022 00:46:38 +0000 (01:46 +0100)]
arm: imx: imx8m: Only use ROM pointers if not PSCI provider
The ROM pointers are in fact populated by the ATF BL31 blob, in case
U-Boot itself if the PSCI provider, there is no ATF BL31 blob, hence
ignore the ROM pointers.
Marek Vasut [Thu, 22 Dec 2022 00:46:37 +0000 (01:46 +0100)]
arm: dts: imx8m: Require ATF BL31 blob only if not PSCI provider
In case U-Boot itself if the PSCI provider on i.MX8M, do not
require the ATF BL31 blob, as at that point the blob is useless
and would interfere with U-Boot operation.
Marek Vasut [Thu, 22 Dec 2022 00:46:36 +0000 (01:46 +0100)]
arm: imx: Drop custom lowlevel_init
The custom lowlevel_init implementation is no longer necessary, since
it is responsible for routing and trapping SErrors in U-Boot in EL2,
which is implemented in common code since commit: 6c7691edd55 ("armv8: Always unmask SErrors")
Marek Vasut [Thu, 22 Dec 2022 00:46:35 +0000 (01:46 +0100)]
arm: psci: Fix RESET2 hook
The RESET2 hook is a PSCI v1.1 functionality, rename the macro accordinly.
Add missing handler for the RESET2 hook, so it can be implemented by U-Boot.
They need to be kept so that the mmc cards are in the right order.
Without the aliases, u-boot reports:
MMC: FSL_SDHC: 2, FSL_SDHC: 3
With the aliases, u-boot reports:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
The upstream linux device tree does not contain the same aliases than
u-boot (It keeps the devices order with /dev/mmcblk2 and /dev/mmcblk3).
Because this board has been using different aliases in u-boot
and linux, a imx6q-sabrelite-u-boot.dtsi file is added to be
automatically included in imx6q-sabrelite.dts.
This way, linux and u-boot each keep their own aliases and there
is no breakage on current installations.
This should never be done for new boards as we want to keep linux and
u-boot with the same aliases as much as possible.
This patch is only necessary to avoid breaking existing setups.
The introduction of CONFIG_FSL_QSPI_AHB_FULL_MAP as default in:
def88bce094e ("spi: fsl_qspi: Support to use full AHB space on i.MX")
broke the SPI NAND read access on the Kontron SL i.MX6UL/ULL boards.
Reading data from the flash returns garbage instead of the actual
content. Fix this for now by disabling the introduced option.
In the long run this should be fixed globally.
Fixes: def88bce094e ("spi: fsl_qspi: Support to use full AHB space on i.MX") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Fabio Estevam <festevam@denx.de>
John Keeping [Thu, 19 Jan 2023 12:56:12 +0000 (12:56 +0000)]
power: act8846_pmic: fix number of registers
The highest register on ACT8846 is 0xf5, so set the number of registers
to 0xf6, ensuring that the pmic read/write commands are able to access
all of the supported registers (and many that are not valid, since the
register space is quite sparse).
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for HS400 in mode2timing array.
Add a quirk for Versal NET platform to indicate that HS400 is supported
through bit63 of capability register.
mmc: sdhci: Check and call config_dll callback functions
Check if the low level driver supports config_dll callback function and
call it if it does. Call with dll disable before calling set_clock and
with dll enable after it.
mmc: zynq_sdhci: Add support for eMMC5.1 for Versal NET platform
Add support for eMMC 5.1 for Versal NET platform
- Add new compatible string(xlnx,versal-net-5.1-emmc).
- Add CONFIG_ARCH_VERSAL_NET condition wherever required.
- Add DLL and Delay Chain mode support
- Add input and output tap delays for eMMC.
- Add Strobe select tap for HS400 mode.
Marek Vasut [Thu, 5 Jan 2023 14:19:08 +0000 (15:19 +0100)]
cmd: mmc: Expand bkops handling
Add more capable "bkops" command which allows enabling and disabling both
manual and automatic bkops. The existing 'mmc bkops-enable' subcommand is
poorly named to cover all the possibilities, hence the new-ish subcommand.
Note that both commands are wrappers around the same common code.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Ye Li [Wed, 18 Jan 2023 09:31:15 +0000 (17:31 +0800)]
ARM: dts: imx8ulp-evk: Fix iomuxc issue
The property fsl,mux_mask is deleted by commit ed7bda5 (imx8ulp:
synchronise device tree with linux). This causes the pinctrl
driver not work on 8ULP, so fail to print any log.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
projects / u-boot.git / log