Fix compatible node to use regular Toradex notation.
Annotate device tree with standard Colibri pin muxing comments.
Use open-drain I2C pin muxings.
Alphabetically re-order iomuxc nodes.
Rename snvs-ad7879-int-grp touch interrupt node as per Linux device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Ye Li [Wed, 17 Apr 2019 09:41:23 +0000 (09:41 +0000)]
mxc_ocotp: Disable fuse sense for imx8mq B1
On iMX8MQ Rev B1, reading from fuse box is not allowed. The
OCOTP_READ_FUSE_DATA register is tied to magic number 0xff0055aa
for chip rev. So u-boot has to disable the fuse sense function for it.
Signed-off-by: Ye Li <ye.li@nxp.com> Tested-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Wed, 17 Apr 2019 09:41:20 +0000 (09:41 +0000)]
mxc_ocotp: Update redundancy banks for mx7ulp B0
On mx7ulp B0, beside bank 0 and 1, the fuse bank 9, 10, 28 are changed to
Redundancy mode not ECC, so they can support to program different bits of
a word in multiple times.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 15 Apr 2019 12:00:50 +0000 (12:00 +0000)]
imx: 8qxp_mek: fix fdt_file and console
Fix fdt_file and console to boot upstream Linux Kernel.
Upstream linux use imx8qxp-mek.dtb, and pass lpuart32 to earlycon
will not work for i.MX8QXP, only need to pass earlycon,
check drivers/tty/serial/earlycon.c,
" /* Just 'earlycon' is a valid param for devicetree and ACPI SPCR. */ "
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Ludwig Zenz [Mon, 15 Apr 2019 09:13:08 +0000 (11:13 +0200)]
ARM: imx6: DHCOM i.MX6 PDK: use Kconfig for inclusion of DDR calibration
The four x16 DDR3 are wired in T-topology. From NXP AN4467:
'Although not required, T-Topologies may also benefit from performing
Write Leveling as there are package delays on both the processor and DDR
devices that can be de-skewed by performing Write Leveling. Therefore,
Freescale recommends determining Write Leveling calibration parameters
for all boards, regardless of topology used.'
That is why write level calibration is also done.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Chris Packham [Sat, 13 Apr 2019 08:21:48 +0000 (20:21 +1200)]
ARM: imx: Fix typo in select option for ZMX25
Correct CPU_ARM926EJS1 to CPU_ARM926EJS.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
After DM conversion, the size of U-Boot binary to increase.
Previous size is 480K after DM Conversion the new size is 557K
So it's necessary to increase the dfu request for store u-boot-dtb.img in eMMC.
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
colibri-imx6ull: migrate mmc to using driver model
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
colibri-imx6ull: migrate pinctrl and regulators to dtb/dm
Migrate pinctrl and regulators to device tree resp. driver model:
Ethernet, NAND and UART.
Drop BOARD_EARLY_INIT_F as it is anyway no longer used.
Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Drop disabling SPL_SYS_THUMB_BUILD as we anyway do not use SPL.
Enbale CRC32 verify, USB SDP and EFI loader support.
Drop CMD_GPT and disabling RANDOM_UUID.
Do savedefconfig which drops USB_FUNCTION_SDP.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Disable output driver of PAD CCM_PMIC_STBY_REQ. This prevents the
SOC to request for a lower voltage during sleep. This is necessary
because the voltage is changing too slow for the SOC to wake up
properly.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Stefan Agner [Tue, 9 Apr 2019 15:24:10 +0000 (17:24 +0200)]
apalis/colibri_imx6/imx6ull: make sure loadaddr does not collide
Currently $loadaddr and $fdt_addr_r point to the same address. This
might be not ideal for some distro boot scripts which make use of
$loadaddr after loading the device tree.
Make sure the two variables point to two different addresses. Moving
$loadaddr is not entirly trivial since it is defined in mx6_common.h.
Move $fdt_addr_r and $ramdisk_addr_r by 1MiB, which should be enough
for scripts.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Stefan Agner [Tue, 9 Apr 2019 15:24:09 +0000 (17:24 +0200)]
colibri-imx6ull: set module variant depending on config block
Using CPU temperature grading as a discriminator if the Wi-Fi /
Bluetooth chip is populated is no longer possible due to upcoming
SKUs. Set variant to -wifi only if a valid config block is present
and the product id mentions a SKU with Wi-Fi / Bluetooth.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Stefan Agner [Tue, 9 Apr 2019 15:24:08 +0000 (17:24 +0200)]
tdx-cfg-block: simplify i.MX 6 module detection
Use CONFIG_TARGET_... at compile time to differentiate between
Apalis iMX6, Colibri iMX6 and Colibri iMX6ULL. Avoid code
duplication by moving question about Wi-Fi / Bluetooth before
IT/non-IT decision.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Thu, 28 Mar 2019 22:24:50 +0000 (23:24 +0100)]
colibri_vf: fix ethernet by adding explicit phy node
The implicit fallback mechanism for searching the whole MDIO bus for at
least one PHY has been gone with the following commit b882005a18de
("drivers/net/fec: phy_init: remove redundant logic"). This lead to the
Ethernet driver erroring out as follows:
Net: Could not get PHY for FEC0: addr -19
eth-1: fec@400d1000
Colibri VFxx # dhcp
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
No ethernet found.
Could not get PHY for FEC0: addr -19
Colibri VFxx #
This commit adds an explicit PHY node which makes it work again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This commit converts i.MX5's EHCI USB host driver to driver model (DM_USB).
It is a straightforward conversion (to reuse as much code as possible),
based on ehci-mx6.c code.
DTS: Enable USB host support (including regulators) on HSC|DDC boards
This commit enables the support for K&P's HSC|DDC imx53 based boards.
It was also necessary to provide device tree description for regulators
to avoid board specific code definition.
The GPIO pin description responsible for VBUS control has been moved from
"hog" group to usbh1 dedicated one.
DTS: Provide USB host DTS description for i.MX53 devices
This code has been ported from Linux kernel - tag v5.1-rc2.
The difference from the kernel is the removal of:
fsl,usbmisc = <&usbmisc 1>;
fsl,usbphy = <&usbphy1>;
properties, which are not needed for correct u-boot operation (as PHY
setup is done in ehci-mx5.c file itself).
Adam Ford [Thu, 11 Apr 2019 18:44:59 +0000 (13:44 -0500)]
ARM: imx6q_logic: Allow storing environment in FAT on eMMC
Some variations of the imx6q_logic board have eMMC instead of
NAND. Rather than creating a separate defconfig, this patch
adds the ability to read/write to eMMC (mmc 0:1) when NAND
doesn't exist.
Adam Ford [Thu, 11 Apr 2019 18:46:09 +0000 (13:46 -0500)]
ARM: imx6q_logic: Allow optional arguments to cmd line
This adds an extra, optional environmental variable called
'optargs' which if enabled allow additional parameters to be
passed to the kernel (ie, quiet, cma=128M, etc.)
Each script that setups the bootargs will just append this.
Tom Rini [Wed, 24 Apr 2019 13:04:23 +0000 (09:04 -0400)]
Merge branch '2019-04-22-master-imports'
- Add and enable brcmnand driver on a number of relevant platforms.
Also add and enable LED drivers on more bcm platforms.
- Various ARMv8 fixes/improvements, including extending PSCI
functionality.
- fs_loader improvments
- Various FIT/SPL improvements
- PCI bugfixes
- Poplar platform ethernet support
- MediaTek MMC improvements
- Android boot improvements
According to Android image format [1], kernel image resides at 1 page
offset from the boot image address. Grab the magic number from there
and allow U-Boot to handle LZ4-compressed KNL binaries instead of
hardcoding compression type to IH_COMP_NONE. Other compression types,
if needed, can be added later.
Tested on H3ULCB-KF using the image detailed in [2].
[1] Excerpt from include/android_image.h
+-----------------+
| boot header | 1 page
+-----------------+
| kernel | n pages
+-----------------+
| ramdisk | m pages
+-----------------+
| second stage | o pages
+-----------------+
Lars Povlsen [Thu, 4 Apr 2019 12:38:50 +0000 (14:38 +0200)]
ARMv8: PSCI: Fix PSCI_TABLE relocation issue
This fixes relaction isses with the PSCI_TABLE entries in
the psci_32_table and psci_64_table.
When using 32-bit adress pointers relocation was not being applied to
the tables, causing PSCI handlers to point to the un-relocated code
area. By using 64-bit data relocation is properly applied. The
handlers are thus in the "secure data" area, which is protected by
/memreserve/ in the FDT.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Trent Piepho [Wed, 27 Mar 2019 23:50:09 +0000 (23:50 +0000)]
bootm: Simplying cache flush code
The cache flush of the kernel load area needs to be aligned outward to
the DMA cache alignment. The operations are simpler if we think of this
as aligning the start down, ALIGN_DOWN(load, ARCH_DMA_MINALIGN), and
aligning the end up, ALIGN(load_end, ARCH_DMA_MINALIGN), and then find
the length of the flushed region by subtracting the former from the
latter.
Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Simon Glass <sjg@chromium.org>
malloc: Fix memalign not honoring alignment prior to full malloc init
When using memalign() in a scenario where U-Boot is configured for full
malloc support with simple malloc not explicitly enabled and before the
full malloc support is initialized, a memory block is being allocated
and returned without the alignment parameter getting honored.
Fix this issue by replacing the existing memalign pre-full malloc init
logic with a call to memalign_simple() this way ensuring proper alignment
of the returned memory block.
Fixes: ee038c58d519 ("malloc: Use malloc simple before malloc is fully initialized in memalign()") Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Stefan Roese [Tue, 26 Mar 2019 12:04:00 +0000 (13:04 +0100)]
spl: spl_nand.c: Add NAND loading message
This patch adds a short message to the SPL NAND loader, which displays
the source and destinations addresses including the size of the
loaded image, like this:
U-Boot SPL 2019.04-rc3-00113-g486efd8aaf (Mar 15 2019 - 14:18:02 +0100)
Trying to boot from NAND
Loading U-Boot from 0x00040000 (size 0x000a0000) to 0x22900000
I find this message quite helpful - hopefully others do so as well.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Shawn Guo [Wed, 20 Mar 2019 07:32:41 +0000 (15:32 +0800)]
poplar: enable Ethernet driver support
The 'phy' reset of gmac device in kernel device tree is not generic
enough for u-boot to use, so we need to overwrite the 'resets' property
as needed. With this device tree fixup and poplar_defconfig changes,
Ethernet starts working on Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Shawn Guo [Wed, 20 Mar 2019 07:32:40 +0000 (15:32 +0800)]
net: add higmacv300 Ethernet driver for HiSilicon platform
It adds the driver for HIGMACV300 Ethernet controller found on HiSilicon
SoCs like Hi3798CV200. It's based on a downstream U-Boot driver, but
quite a lot of code gets rewritten and cleaned up to adopt driver model
and PHY API.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Shawn Guo [Wed, 20 Mar 2019 07:32:39 +0000 (15:32 +0800)]
reset: add reset driver for HiSilicon platform
It adds a Driver Model compatible reset driver for HiSlicon platform.
The driver implements a custom .of_xlate function, and uses .data field
as reset register offset and .id field as bit shift.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Thierry Reding [Fri, 15 Mar 2019 15:32:33 +0000 (16:32 +0100)]
pci: Scale MAX_PCI_REGIONS based on CONFIG_NR_DRAM_BANKS
If a platform defines CONFIG_NR_DRAM_BANKS, each DRAM bank will be added
as a PCI region. The number of MAX_PCI_REGIONS therefore needs to scale
with the number of DRAM banks, otherwise we will end up with too little
space in the hose->regions array to store all system memory regions.
Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Thierry Reding [Fri, 15 Mar 2019 15:32:32 +0000 (16:32 +0100)]
pci: Add boundary check for hose->regions
Make sure that we don't overflow the hose->regions array, otherwise we
would end up overwriting the hose->region_count field and cause mayhem
to ensue. Also print an error message when we'd be overflowing because
it indicates that there aren't enough regions available and the number
needs to be increased.
Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log