Convert 'cadence_spi_ofdata_to_platdata' to use dev_read_* functions to
read driver parameters and 'dev_read_first_subnode'/'ofnode_read_*' to
read flash (child node) parameters.
Tested on socfpga_socrates (socfpga gen5).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tien Fong Chee [Tue, 7 May 2019 09:42:32 +0000 (17:42 +0800)]
ARM: socfpga: Increase Malloc pool size to support FAT filesystem in SPL
Increasing Malloc pool size up to 0x15000 is required to support FAT in SPL
. The result of calculation is come from default max cluster(0x10000) +
others(0x2000) + additional memory for headroom(0x3000).
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Tien Fong Chee [Tue, 7 May 2019 09:42:30 +0000 (17:42 +0800)]
spl: socfpga: Implement fpga bitstream loading with socfpga loadfs
Add support for loading FPGA bitstream to get DDR up running before
U-Boot is loaded into DDR. Boot device initialization, generic firmware
loader and SPL FAT support are required for this whole mechanism to work.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Tien Fong Chee [Tue, 7 May 2019 09:42:29 +0000 (17:42 +0800)]
ARM: socfpga: Add the configuration for FPGA SoCFPGA A10 SoCDK
Update the default configuration file to enable the necessary functionality
to get the SoCFPGA loadfs driver support. This would enable the
implementation of programming bitstream into FPGA from MMC.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add FPGA driver to support program FPGA with FPGA bitstream loading from
filesystem. The driver are designed based on generic firmware loader
framework. The driver can handle FPGA program operation from loading FPGA
bitstream in flash to memory and then to program FPGA.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Tien Fong Chee [Tue, 7 May 2019 09:42:27 +0000 (17:42 +0800)]
ARM: socfpga: Moving the watchdog reset to the for-loop status polling
Current watchdog reset is misplaced after for-loop status polling, so
this poses a risk that watchdog can't be reset timely if polling taking
longer than watchdog timeout. This patch moving the watchdog reset
into polling to ensure the watchdog can be reset timely.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Marek Vasut [Tue, 7 May 2019 19:59:57 +0000 (21:59 +0200)]
sh: mpr2: Remove the board
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Mark Jonas <mark.jonas@de.bosch.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Chris Packham [Sat, 13 Apr 2019 09:13:58 +0000 (21:13 +1200)]
Remove #define CONFIG_CRC32
There is no check for CONFIG_CRC32 so the #define in image.h does
nothing. Remove it.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
Chris Packham [Sat, 13 Apr 2019 08:35:23 +0000 (20:35 +1200)]
sysreset: select DM_GPIO instead of GPIO
CONFIG_GPIO does not exist. sysreset_gpio.c uses the DM gpio APIs so the
correct option to select is DM_GPIO.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 10 May 2019 11:07:49 +0000 (07:07 -0400)]
Merge branch '2019-05-09-master-imports'
- Minor fixes (ata memory leak, implement feedback on ohci-da8xx
changes, avb test fix, mmc test fix, spelling fixes, make FIT really
optional, fit-dtb blob cleanups, TI K3 workflow improvements, bootz
can boot barebox on 32bit ARM).
There is one case where 400ms is not sufficient for loading the
system firmware:
- System firmware is not signed with rsa degenerate key.
- ROM loading the sysfw directly from SPI flash which is in memory
mapped mode.
The above scenario is definitely not desired in production use cases
as it effects boot time. But still keeping this support as this is
a valid boot scenario.
Lokesh Vutla [Thu, 2 May 2019 10:05:50 +0000 (15:35 +0530)]
tools: k3_get_x509 cert: Add a script to generate x509 certificate for K3 devices
TI's K3 boot architecture mandates a x509 certificate for every boot image.
While signing the image K3 ROM allows for two types of keys based on which
the boot image gets loaded in different ways:
- Degenerate RSA keys: This generates a signature which is equal to the digest.
When ROM sees this, it does a DMA for copying the images,
which significantly improves the boot time.
- Any other key: Does a memcpy to load the image. This is introduced as a
fallback for DMA copy.
Add a script for generating boot images with the above options. Default
generates image using rsa degenerate key in order to improve boot time.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Stephen Warren [Tue, 16 Apr 2019 22:04:49 +0000 (16:04 -0600)]
test/py: don't use mmc_rd config for other mmc tests
Fix test_mmc_dev(), test_mmc_rescan(), test_mmc_info() not to use the
same configuration data that test_mmc_rd() does. Doing so causes the
following issues:
* The new code uncondtionally expects certain keys to exist in the
configuration data. These keys do not exist in existing configuration
data since they were not previously required, and there was no
notification re: a requirement to add these new keys. This causes test
failures due to thrown exceptions when accessing the non-existent keys.
* The new tests logically operate on different objects. test_mmc_rd()
operates on ranges of sectors on an MMC device (which may be the entire
set of sectors of a device, or a part of a device), whereas all the new
tests operate solely on entire devices. These are separate things, and
it's entirely likely that the user will wish to runs the two types of
tests on different sets of data; see the example configuration data that
this commit adds. Ideally, the new tests would have been added to a
separate Python file, since they aren' closely related to the existing
tests.
FIXME: Marek, can you please replace the "???" in this patch with some
reasonable looking data? Thanks.
fdt_shrink_to_minimum: do not mark fdt space reserved unconditionally
This function merely relocates the fdt blob, so don't let it alter
it by adding reservations that didn't exist before.
Instead, if the memory used for the fdt blob has been reserved
before calling this function, ensure the relocated memory is
marked as reserved instead.
Due to some mistakes in the source code, it was not possible to really
turn FIT support off. This commit fixes the problem by means of the
following changes:
- Enclose "bootm_host_load_image" and "bootm_host_load_images" between
checks for CONFIG_FIT_SIGNATURE, in common/bootm.c.
- Enclose the declaration of "bootm_host_load_images" between checks for
CONFIG_FIT_SIGNATURE, in common/bootm.h.
- Condition the compilation and linking of fit_common.o fit_image.o
image-host.o common/image-fit.o to CONFIG_FIT=y, in tools/Makefile.
Signed-off-by: Carlos Santos <casantos@datacom.ind.br>
[fabio: adapt for 2016.07] Signed-off-by: Fabio Estevam <festevam@gmail.com>
[Ricardo: fix conditional compilation and linking of the files mentioned above
for 2016.07] Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
[Jörg: adapt for 2019.01] Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
[Retrieved from:
https://git.buildroot.net/buildroot/tree/package/uboot-tools/0003-Make-FIT-support-really-optional.patch] Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Marek Vasut [Sat, 4 May 2019 17:10:05 +0000 (19:10 +0200)]
env: spi: Fix incorrect entry description
Fix the max frequency entry description, it's incorrect.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Tom Rini <trini@konsulko.com>
Adam Ford [Tue, 7 May 2019 11:57:39 +0000 (06:57 -0500)]
usb: ohci: ohci-da8xx: Cleanup Error handling and fix flags
Per feedback from Marek, he suggested better handling and
to enable DM_FLAG_OS_PREPARE, this patch re-orders some of
the error checking, and errors returns the error code right
away and also sets DM_FLAG_OS_PREPARE.
Stefan Roese [Thu, 9 May 2019 08:16:20 +0000 (10:16 +0200)]
dm: MIGRATION: Add migration plan for WDT (DM watchdog support)
As much of the watchdog system has been migrated to DM now, formalize a
deadline for migration.
Please note that the old CONFIG_HW_WATCHDOG macro should be removed
completely at some point.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 9 May 2019 11:12:51 +0000 (07:12 -0400)]
Merge tag 'rockchip-for-v2019.07-rc1' of git://git.denx.de/u-boot-rockchip
Improvements and new features:
- split more rockchip pinctrl_core feature into per SoC
- enable TPL for evb-rk3399 board
- enable TPL/SPL for evb-px5 board
- enable TPL and OP-TEE support for evb-rk3229
- update fix in arm common assembly start code for rockchip header file
- update default SPL_FIT_GENERATOR for rockchip
- rk3399 boards update to use '-u-boot.dtsi'
- add new rk3399 boards: Nanopi M4, Nanopc T4
- enable sound for chromebook_minnie
Jagan Teki [Wed, 8 May 2019 05:41:51 +0000 (11:11 +0530)]
doc: rockchip: Add global doc for rk3399 build/flash
Since rockchip have an individual doc/README.rockchip, it would
be better to update the same instead of maintaining it separately
in board files.
So, add the documentation for rk3399
- procedure to build for Rockchip miniloader and
U-Boot SPL options
- procedure to boot from SD for Rockchip miniloader and
U-Boot SPL options
- procedure to build ATF, PMU M0 firmware for puma boards
- add boot logs of each option, so-that it would help for future
boards porting
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Wed, 8 May 2019 05:41:47 +0000 (11:11 +0530)]
rockchip: rk3399: Add Nanopc T4 board support
Add initial support for Nanopc T4 board.
Specification
- Rockchip RK3399
- Dual-Channel 4GB LPDDR3-1866
- SD card slot
- 16GB eMMC
- RTL8211E 1Gbps
- AP6356S WiFI/BT
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-nanopc-t4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: Add NanoPC-T4 IR receiver"
(sha1: 95658e21b1707ad7844f873db2fdaa295109a5a3)
Tested-by: Daniel Gröber <dxld@darkboxed.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Wed, 8 May 2019 05:41:46 +0000 (11:11 +0530)]
rockchip: rk3399: Add Nanopi M4 board support
Add initial support for Nanopi M4 board.
Specification
- Rockchip RK3399
- Dual-Channel 4GB LPDDR3-1866
- SD card slot
- eMMC socket
- RTL8211E 1Gbps
- AP6356S WiFI/BT
- HDMI In/Out, DP, MIPI DSI/CSI
- USB 3.0 x4
- USB Type C power and data
- GPIO1, GPIO2 expansion ports
- DC5V/3A
Commit details of rk3399-nanopi-m4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: Refine nanopi4 differences"
(sha1: c62ffaf5026d0b7633e62b2cea8450b5543c349a)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Jagan Teki [Wed, 8 May 2019 05:41:45 +0000 (11:11 +0530)]
rockchip: dts: rk3399: nanopi4: Use CD pin as RK_FUNC_1
Attaching GPIO functionality to SDMMC0_DET pin (which
does in Linux base dts) make dwmmc driver "fail to detect
the card".
Card did not respond to voltage select!
It may be because the existing driver can't support gpio
card detection. So, change the pinctrl functionality from
RK_FUNC_GPIO to RK_FUNC_1 like other rk3399 dts does via
sdmmc_cd pin.
Cc: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Atish Patra [Tue, 7 May 2019 00:49:39 +0000 (17:49 -0700)]
RISCV: image: Add booti support
This patch adds booti support for RISC-V Linux kernel. The existing
bootm method will also continue to work as it is.
It depends on the following kernel patch which adds the header to the
flat Image. Gzip compressed Image (Image.gz) support is not enabled with
this patch.
Rick Chen [Tue, 30 Apr 2019 05:49:33 +0000 (13:49 +0800)]
riscv: Introduce CONFIG_XIP to support booting from flash
When U-Boot boots from flash, during the boot process,
hart_lottery and available_harts_lock variable addresses
point to flash which is not writable. This causes boot
failures on AE350. Introduce a config option CONFIG_XIP
to support such configuration.
Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
riscv: qemu: Use correct SYS_TEXT_BASE for S-mode on 32bit system
For 32bit system, the OpenSBI (or BBL) will jump to 0x80400000 address
in S-mode whereas for 64bit system it will jump to 0x80200000 address
in S-mode.
Currently, the S-mode U-Boot sets SYS_TEXT_BASE to 0x80200000 for both
32bit and 64bit system. This breaks S-mode U-Boot for 32bit system.
This patch sets different SYS_TEXT_BASE for 32bit and 64bit system so
that S-mode U-Boot works fine for both.
After updating Fedora/RISCV kernel to 5.1-rc3+ the size increased above
the current threshold. Looking into HiKey, Dragonboards, etc. seems that
SZ_64M is a popular option.
This sucessfully boots Fedora/RISCV with 5.1-rc3+ kernel on QEMU 4.0 (master)
with OpenSBI -> U-Boot (S-mode) [extlinux] -> Kernel setup.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Neil Armstrong [Tue, 19 Feb 2019 13:21:04 +0000 (14:21 +0100)]
mach-meson: g12a: add DWC2 peripheral mode support
Adds support for Amlogic G12A USB Device mode.
The DWC2 Controller behind the Glue can be connected to an OTG
capable PHY. The Glue setups the PHY mode.
This patch implements Device mode support by adding a board_usb_init/cleanup
setting up the DWC2 controller and switch the OTG capable port to Device
before starting the DWC2 controller in Device mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Tue, 19 Feb 2019 14:17:29 +0000 (15:17 +0100)]
phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY drivers
This adds support for the USB PHYs found in the Amlogic G12A SoC Family.
The USB2 PHY supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.
The second driver supports USB3 Host mode or PCIE 2.0 mode, depending on
the layout of the board.
Selection is done by the #phy-cells, making the mode static and exclusive.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Tue, 19 Feb 2019 12:42:01 +0000 (13:42 +0100)]
usb: dwc3: Add Meson G12A USB Glue
Adds support for Amlogic G12A USB Control Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
This driver sets the OTG capable port as Host mode by default,
the switch to Device mode is to be done in a separate patch.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Marek Vasut <marex@denx.de>
Luka Kovacic [Tue, 7 May 2019 17:35:55 +0000 (19:35 +0200)]
arm: mvebu: Add CRS305-1G-4S board
CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and
like some of the other similar boards requires bin_hdr.
bin_hdr (DDR3 init stage) is currently retrieved from the stock
bootloader and compiled into the kwb image.
Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip
support and writing env to SPI flash.
Signed-off-by: Luka Kovacic <me@lukakovacic.xyz> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 3 May 2019 06:42:19 +0000 (08:42 +0200)]
arm: mvebu: db-88f6820-gp: Enable BLK and DM support
This patch enables CONFIG_BLK and some DM enabled drivers on
db-88f6820-gp to remove these compile warnings:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does use CONFIG_LIBATA but has CONFIG_AHCI not
enabled. Please update the storage controller driver to use
CONFIG_AHCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Chris Packham <judge.packham@gmail.com>
This patch enables CONFIG_BLK to remove this compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Stefan Roese [Fri, 3 May 2019 06:42:17 +0000 (08:42 +0200)]
arm: mvebu: clearfog: Enable BLK and DM support
This patch enables CONFIG_BLK and some DM enabled drivers on clearfog
to remove these compile warnings:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does use CONFIG_LIBATA but has CONFIG_AHCI not
enabled. Please update the storage controller driver to use
CONFIG_AHCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
James Byrne [Mon, 4 Mar 2019 17:40:34 +0000 (17:40 +0000)]
net: phy: micrel: Find Micrel PHY node correctly
In some of the device trees that specify skew values for KSZ90x1 PHYs
the values are stored (incorrectly) in the MAC node, whereas in others
it is in an 'ethernet-phy' subnode. Previously the code would fail to
find and program these skew values, so this commit changes it to look
for an "ethernet-phy" subnode first, and revert to looking in the MAC
node if there isn't one.
The device trees affected (where the skew values are in a subnode) are
imx6qdl-icore-rqs.dtsi, r8a77970-eagle.dts, r8a77990-ebisu.dts,
r8a77995-draak.dts, salvator-common.dtsi, sama5d3xcm.dtsi,
sama5d3xcm_cmp.dtsi, socfpga_cyclone5_vining_fpga.dts,
socfpga_stratix10_socdk.dts and ulcb.dtsi. Before this change the skew
values in these device trees would be ignored.
The device trees where the skew values are in the MAC node are
socfpga_arria10_socdk.dtsi, socfpga_arria5_socdk.dts,
socfpga_cyclone5_de0_nano_soc.dts, socfpga_cyclone5_de10_nano.dts,
socfpga_cyclone5_de1_soc.dts, socfpga_cyclone5_is1.dts,
socfpga_cyclone5_socdk.dts, socfpga_cyclone5_sockit.dts. These should be
unaffected by this change.
The changes were tested on a sama5d3xcm.
Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
James Byrne [Mon, 4 Mar 2019 17:40:33 +0000 (17:40 +0000)]
net: phy: micrel: Use correct skew values on KSZ9021
Commit ff7bd212cb8a ("net: phy: micrel: fix divisor value for KSZ9031
phy skew") fixed the skew value divisor for the KSZ9031, but left the
code using the same divisor for the KSZ9021, which is incorrect.
The preceding commit c16e69f702b1 ("net: phy: micrel: add documentation
for Micrel KSZ90x1 binding") added the DTS documentation for the
KSZ90x1, changing it from the equivalent file in the Linux kernel to
correctly state that for this part the skew value is set in 120ps steps,
whereas the Linux documentation and driver continue to this day to use
the incorrect value of 200 that came from the original KSZ9021 datasheet
before it was corrected in revision 1.2 (Feb 2014).
This commit sorts out the resulting confusion in a consistent way by
making the following changes:
- Update the documentation to be clear about what the skew values mean,
in the same was as for the KSZ9031.
- Update the Micrel PHY driver to select the appropriate divisor for
both parts.
- Adjust all the device trees that state skew values for KSZ9021 PHYs to
use values based on 120ps steps instead of 200ps steps. This will result
in the same values being programmed into the skew registers as the
equivalent device trees in the Linux kernel do, where it incorrectly
uses 200ps steps (since that's where all these device trees were copied
from).
Signed-off-by: James Byrne <james.byrne@origamienergy.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: phy: aquantia: Set only autoneg on in register 4.c441
For AQR405 in register 4.c441 bit 15 was override with 0. This caused the
phy to not negotiate at 2.5GB rate with mac. To avoid
this override it needed first to know the previous value of reg 4.c441
and set only bit 3.
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: phy: Reloc next and prev pointers inside phy_drivers
This patch relocates the pointers inside phy_drivers incase
of manual reloc. Without this reloc, these points to invalid
pre relocation address and hence causes exception or hang.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Murali Karicheri [Mon, 25 Feb 2019 20:27:34 +0000 (15:27 -0500)]
ARM: k2g-ice: Add pinmux support for rgmii interface
This add pinmux configuration for rgmii interface so that network
driver can be supported on K2G ICE boards. The pinmux configurations
for this are generated using the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
As this required some BUFFER_CLASS definitions, same is re-used
from the linux defnitions in include/dt-bindings/pinctrl/keystone.h
Chen-Yu Tsai [Fri, 3 May 2019 02:27:41 +0000 (10:27 +0800)]
sunxi: Enable EMAC on the Bananapi M3
The Bananapi M3 has an RTL8211E PHY connected to the EMAC using
RGMII. The PHY is powered by DCDC1 through SW @ 3.3V.
The board is designed to use 3.3V with RGMII, instead of the standard
reduced voltage of 2.5V we see everywhere. DLDO3, which provides the
I/O voltages, is raised to match.
This patch enables the EMAC and Realtek PHY drivers in the defconfig.
The device tree file already has the EMAC enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Chen-Yu Tsai [Fri, 3 May 2019 02:27:40 +0000 (10:27 +0800)]
sunxi: Enable EMAC on the Cubietruck Plus
The Cubietruck Plus has an RTL8211E PHY connected to the EMAC using
RGMII. The PHY is powered by DLDO4 @ 3.3V, while the I/O pins are
powered by DLDO3 @ 2.5V.
This patch enables the EMAC and Realtek PHY drivers in the defconfig.
The device tree file already has the EMAC enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Known broken:
- Internal keyboard (seems to be because the keyboard firmware loads a
bootloader first, and then disconnects bootloader and connect real
keyboard). External ones connected to the USB port work fine.
This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).
Linux commit details about the sun50i-a64-teres-i.dts sync:
"arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins"
(sha1: d91ebb95b96c8840932dc3a10c9f243712555467)
Cosmetic warnings regarding whitespace and placement of SPDX notice for
dts file was ignored.
config and .dtsi file are adapted from pinebook files.
Tested-by: Jonas Smedegaard <dr@jones.dk> Signed-off-by: Jonas Smedegaard <dr@jones.dk> Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: move board entry in MAINTAINERS file at proper position] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 27 Feb 2019 18:56:55 +0000 (00:26 +0530)]
reset: Get the RESET by index without device
Getting a RESET by index with device is not straight forward
for some use-cases like handling clock operations for child
node in parent driver. So we need to process the child node
in parent probe via ofnode and process RESET operation for child
without udevice but with ofnode.
So add reset_get_by_index_nodev() and move the common code
in reset_get_by_index_tail() to use for reset_get_by_index()
Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Wed, 27 Feb 2019 18:56:52 +0000 (00:26 +0530)]
clk: Get the CLK by index without device
Getting a CLK by index with device is not straight forward
for some use-cases like handling clock operations for child
node in parent driver. So we need to process the child node
in parent probe via ofnode and process CLK operation for child
without udevice but with ofnode.
So add clk_get_by_index_nodev() and move the common code
in clk_get_by_index_tail() to use for clk_get_by_index()
Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Wed, 8 May 2019 14:26:16 +0000 (19:56 +0530)]
serial: sifive: Change include order
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the serial_sifive driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/riscv/include/asm/u-boot.h:23:0,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from drivers/serial/serial_sifive.c:6:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in serial_sifive.c to include first common.h file.
Cc: Anup Patel <Anup.Patel@wdc.com> Cc: Rick Chen <rick@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 8 May 2019 14:22:18 +0000 (19:52 +0530)]
clk: sifive: fu540-prci: Change include order
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the fu540-prci driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/riscv/include/asm/u-boot.h:23:0,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from include/clk-uclass.h:13,
from drivers/clk/sifive/fu540-prci.c:32:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in fu540-prci.c to include first common.h file.
Cc: Anup Patel <Anup.Patel@wdc.com> Cc: Rick Chen <rick@andestech.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
projects / u-boot.git / log