]> git.dujemihanovic.xyz Git - u-boot.git/log
u-boot.git
4 years agoMerge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
Tom Rini [Thu, 13 Aug 2020 12:25:25 +0000 (08:25 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell

- Fix dtc warnings for some MVEBU boards

4 years agoMerge tag 'u-boot-stm32-20200813' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
Tom Rini [Thu, 13 Aug 2020 12:11:27 +0000 (08:11 -0400)]
Merge tag 'u-boot-stm32-20200813' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

  - Use IS_ENABLED to prevent ifdef in board_key_check for STM32MP
  - Add STM32 FMC2 EBI controller driver
  - Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
  - Add fitImage its entry for 587-200 DHCOR SoM
  - Add both PDK2 and DRC02 DT into DHCOM fitImage its
  - Fix DHCOM KS8851 ethernet MAC address
  - Remove stm32mp1 board.c file
  - Use const for struct node_info in board stm32mp1.c file

4 years agoarm: mvebu: armada-3720-turris-mox.dts: Fix dtc warning
Stefan Roese [Mon, 10 Aug 2020 08:16:56 +0000 (10:16 +0200)]
arm: mvebu: armada-3720-turris-mox.dts: Fix dtc warning

Fix this dtc warning:
Warning (avoid_default_addr_size)

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek BehĂșn <marek.behun@nic.cz>
4 years agoarm: mvebu: armada-388-gp.dts: Fix dtc warnings
Stefan Roese [Mon, 10 Aug 2020 08:16:55 +0000 (10:16 +0200)]
arm: mvebu: armada-388-gp.dts: Fix dtc warnings

Fix these dtc warnings:
Warning (reg_format)
Warning (avoid_default_addr_size)

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
4 years agoarm: mvebu: armada-xp-maxbcm.dts: Fix dtc warning
Stefan Roese [Mon, 10 Aug 2020 08:16:54 +0000 (10:16 +0200)]
arm: mvebu: armada-xp-maxbcm.dts: Fix dtc warning

Fix this dtc warning:
Warning (avoid_default_addr_size)

Signed-off-by: Stefan Roese <sr@denx.de>
4 years agoarm: mvebu: armada-xp-theadorable.dts: Fix dtc warning
Stefan Roese [Mon, 10 Aug 2020 08:16:53 +0000 (10:16 +0200)]
arm: mvebu: armada-xp-theadorable.dts: Fix dtc warning

Fix this dtc warning:
Warning (avoid_default_addr_size)

Signed-off-by: Stefan Roese <sr@denx.de>
4 years agoboard: stm32mp1: use const for struct node_info
Patrick Delaunay [Wed, 29 Jul 2020 11:24:52 +0000 (13:24 +0200)]
board: stm32mp1: use const for struct node_info

Use const for the variable nodes in ft_board_setup,
this patch follow fdt_fixup_mtdparts prototype and no more use stack.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoboard: stm32mp1: remove board.c
Patrick Delaunay [Thu, 30 Jul 2020 11:57:34 +0000 (13:57 +0200)]
board: stm32mp1: remove board.c

Remove the file board/st/stm32mp1/board.c which is not more
compiled since commit 156732cc8939 ("board: stm32mp1: move the
function board_debug_uart_init in spl.c")

Fixes: 4fb46816c7e2 ("board: stm32mp1: move the function board_debug_uart_init in spl.c")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoARM: dts: stm32: Update eth1addr from EEPROM if eth1 present
Marek Vasut [Thu, 30 Jul 2020 23:34:50 +0000 (01:34 +0200)]
ARM: dts: stm32: Update eth1addr from EEPROM if eth1 present

The STM32MP1 DHCOM has two ethernet interfaces, the on-SoM DWMAC and KS8851.
Set eth1addr for the KS8851 to a MAC address of the DWMAC incremented by 1.
The MAC of the DWMAC is set from on-SoM EEPROM already, but the MAC address
of KS8851 was left uninitialized, so fix this.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoARM: stm32: Add fitImage its entry for 587-200 DHCOR SoM
Marek Vasut [Thu, 30 Jul 2020 23:35:51 +0000 (01:35 +0200)]
ARM: stm32: Add fitImage its entry for 587-200 DHCOR SoM

The new 587-200 DHCOR SoM is compatible with the 587-100 prototype,
hence just replicate the entries, as there is no pattern matching.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoARM: stm32: Add both PDK2 and DRC02 DT into DHCOM fitImage its
Marek Vasut [Thu, 30 Jul 2020 23:35:33 +0000 (01:35 +0200)]
ARM: stm32: Add both PDK2 and DRC02 DT into DHCOM fitImage its

Include both PDK2 and DRC02 DTs in the DHCOM fitImage .its and implement
support in SPL to select the correct configuration entry for U-Boot by
using the machine compatible string from SPL DT.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoARM: dts: stm32: add FMC2 EBI support for stm32mp157c
Christophe Kerello [Fri, 31 Jul 2020 07:53:44 +0000 (09:53 +0200)]
ARM: dts: stm32: add FMC2 EBI support for stm32mp157c

This patch adds FMC2 External Bus Interface support on stm32mp157c.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoconfigs: stm32mp: add CONFIG_STM32_FMC2_EBI
Christophe Kerello [Fri, 31 Jul 2020 07:53:43 +0000 (09:53 +0200)]
configs: stm32mp: add CONFIG_STM32_FMC2_EBI

This patch enables the support of FMC2 EBI.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoboard: stm32mp1: update fdt fixup partitions table
Christophe Kerello [Fri, 31 Jul 2020 07:53:42 +0000 (09:53 +0200)]
board: stm32mp1: update fdt fixup partitions table

This patch adds "st,stm32mp1-fmc2-nfc" compatible string in the
fdt fixup partitions table.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agomtd: rawnand: stm32_fmc2: get resources from parent node
Christophe Kerello [Fri, 31 Jul 2020 07:53:41 +0000 (09:53 +0200)]
mtd: rawnand: stm32_fmc2: get resources from parent node

FMC2 EBI support has been added. Common resources (registers base
address and clock) can now be shared between the 2 drivers using
"st,stm32mp1-fmc2-nfc" compatible string. It means that the
common resources should now be found in the parent device when EBI
node is available.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agomemory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver
Christophe Kerello [Fri, 31 Jul 2020 07:53:40 +0000 (09:53 +0200)]
memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver

The driver adds the support for the STMicroelectronics FMC2 EBI controller
found on STM32MP SOCs.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agomtd: rawnand: stm32_fmc2: use clrsetbits_le32
Christophe Kerello [Fri, 31 Jul 2020 07:53:39 +0000 (09:53 +0200)]
mtd: rawnand: stm32_fmc2: use clrsetbits_le32

This patch uses clrsetbits_le32 function instead of multiple instructions.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agomtd: rawnand: stm32_fmc2: use FIELD_PREP/FIELD_GET macros
Christophe Kerello [Fri, 31 Jul 2020 07:53:38 +0000 (09:53 +0200)]
mtd: rawnand: stm32_fmc2: use FIELD_PREP/FIELD_GET macros

This patch removes custom macros and uses FIELD_PREP and FIELD_GET macros.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agomtd: rawnand: stm32_fmc2: cosmetic change to use nfc instead of fmc2 where relevant
Christophe Kerello [Fri, 31 Jul 2020 07:53:37 +0000 (09:53 +0200)]
mtd: rawnand: stm32_fmc2: cosmetic change to use nfc instead of fmc2 where relevant

This patch renames functions and local variables.
This cleanup is done to get all functions starting by stm32_fmc2_nfc
in the FMC2 raw NAND driver when all functions will start by
stm32_fmc2_ebi in the FMC2 EBI driver.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agomtd: rawnand: stm32_fmc2: use FMC2_TIMEOUT_5S for timeouts
Christophe Kerello [Fri, 31 Jul 2020 07:53:36 +0000 (09:53 +0200)]
mtd: rawnand: stm32_fmc2: use FMC2_TIMEOUT_5S for timeouts

FMC2_TIMEOUT_5S will be used each time that we need to wait.
It was seen, during stress tests in an overloaded system,
that we could be close to 1 second, even if we never met this
value. To be safe, FMC2_TIMEOUT_MS is set to 5 seconds.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agomtd: rawnand: stm32_fmc2: remove useless inline comments
Christophe Kerello [Fri, 31 Jul 2020 07:53:35 +0000 (09:53 +0200)]
mtd: rawnand: stm32_fmc2: remove useless inline comments

Remove inline comments that are useless since function label are
self explanatory.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agomtd: rawnand: stm32_fmc2: fix a buffer overflow
Christophe Kerello [Fri, 31 Jul 2020 07:53:34 +0000 (09:53 +0200)]
mtd: rawnand: stm32_fmc2: fix a buffer overflow

The chip select defined in the device tree could only be 0 or 1.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoarm: stm32mp: stm32prog: use IS_ENABLED to prevent ifdef
Patrick Delaunay [Fri, 31 Jul 2020 14:31:52 +0000 (16:31 +0200)]
arm: stm32mp: stm32prog: use IS_ENABLED to prevent ifdef

Use IS_ENABLED to prevent ifdef in stm32prog command.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoarm: stm32mp: bsec: use IS_ENABLED to prevent ifdef
Patrick Delaunay [Fri, 31 Jul 2020 14:31:51 +0000 (16:31 +0200)]
arm: stm32mp: bsec: use IS_ENABLED to prevent ifdef

Use IS_ENABLED to prevent ifdef in bsec driver.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoboard: stm32mp1: use IS_ENABLED to prevent ifdef in ft_board_setup
Patrick Delaunay [Fri, 31 Jul 2020 14:31:50 +0000 (16:31 +0200)]
board: stm32mp1: use IS_ENABLED to prevent ifdef in ft_board_setup

Use IS_ENABLED to prevent ifdef in ft_board_setup.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoboard: stm32mp1: use IS_ENABLED to prevent ifdef in env functions
Patrick Delaunay [Fri, 31 Jul 2020 14:31:49 +0000 (16:31 +0200)]
board: stm32mp1: use IS_ENABLED to prevent ifdef in env functions

Use IS_ENABLED to prevent ifdef in env functions:
- env_get_location
- env_ext4_get_intf
- mmc_get_env_dev

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoboard: stm32mp1: use IS_ENABLED to prevent ifdef in board_late_init
Patrick Delaunay [Fri, 31 Jul 2020 14:31:48 +0000 (16:31 +0200)]
board: stm32mp1: use IS_ENABLED to prevent ifdef in board_late_init

Use IS_ENABLED to prevent ifdef in board_late_init.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoboard: stm32mp1: use IS_ENABLED to prevent ifdef in dk2_i2c1_fix
Patrick Delaunay [Fri, 31 Jul 2020 14:31:47 +0000 (16:31 +0200)]
board: stm32mp1: use IS_ENABLED to prevent ifdef in dk2_i2c1_fix

Use IS_ENABLED to prevent ifdef in dk2_i2c1_fix.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoboard: stm32mp1: use IS_ENABLED to prevent ifdef in set_dfu_alt_inf
Patrick Delaunay [Fri, 31 Jul 2020 14:31:46 +0000 (16:31 +0200)]
board: stm32mp1: use IS_ENABLED to prevent ifdef in set_dfu_alt_inf

Use CONFIG_IS_ENABLED to prevent ifdef in set_dfu_alt_inf.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoboard: stm32mp1: use IS_ENABLED to prevent ifdef in sysconf_init
Patrick Delaunay [Fri, 31 Jul 2020 14:31:45 +0000 (16:31 +0200)]
board: stm32mp1: use IS_ENABLED to prevent ifdef in sysconf_init

Use IS_ENABLED to prevent ifdef in sysconf_init.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoboard: stm32mp1: use IS_ENABLED to prevent ifdef in board_check_usb_power
Patrick Delaunay [Fri, 31 Jul 2020 14:31:44 +0000 (16:31 +0200)]
board: stm32mp1: use IS_ENABLED to prevent ifdef in board_check_usb_power

Use IS_ENABLED to prevent ifdef in board_check_usb_power.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoboard: stm32mp1: use IS_ENABLED to prevent ifdef in g_dnl_board_usb_cable_connected
Patrick Delaunay [Fri, 31 Jul 2020 14:31:43 +0000 (16:31 +0200)]
board: stm32mp1: use IS_ENABLED to prevent ifdef in g_dnl_board_usb_cable_connected

Use IS_ENABLED to prevent ifdef in g_dnl_board_usb_cable_connected
and in g_dnl_bind_fixup

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agoboard: stm32mp1: use IS_ENABLED to prevent ifdef in board_key_check
Patrick Delaunay [Fri, 31 Jul 2020 14:31:42 +0000 (16:31 +0200)]
board: stm32mp1: use IS_ENABLED to prevent ifdef in board_key_check

Use IS_ENABLED to prevent ifdef in board_key_check

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
4 years agousb: host: dwc3-sti-glue: Fix ofnode_valid() parameter
Patrice Chotard [Mon, 29 Jun 2020 09:19:02 +0000 (11:19 +0200)]
usb: host: dwc3-sti-glue: Fix ofnode_valid() parameter

node varaible is used as iterator into ofnode_for_each_subnode()
loop, when exiting of it, node is no more a valid ofnode.
Use dwc3_node instead as parameter of ofnode_valid()

Fixes: ac28e59a574d ("usb: Migrate to support live DT for some driver")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
4 years agoMakefile: fix annoying sunxi hack message
Frank Wunderlich [Tue, 11 Aug 2020 15:19:54 +0000 (17:19 +0200)]
Makefile: fix annoying sunxi hack message

every compilation shows this error

 Hack for sunxi which doesn't have a proper binman definition for
 64-bit boards

not only for sunxi-boards/arm64

fix this by changing to real comments

Fixes: 9f55ee259d0c ("Makefile: sunxi: Don't use binman to build ATF image")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
4 years agoMerge tag 'ti-v2020.10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
Tom Rini [Wed, 12 Aug 2020 03:03:46 +0000 (23:03 -0400)]
Merge tag 'ti-v2020.10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti

- Added support for J7200 evm
- DM_ETH and DM_USB migrations for omap3
- USB DFU and mass storage support for AM65x evm
- RTI watchdog support for K3 devices
- Fix an issue with L3 cache on K3 devices

4 years agoarm: dts: k3-j7200-common-proc-board: Enable CPSW2G port
Vignesh Raghavendra [Thu, 6 Aug 2020 18:57:01 +0000 (00:27 +0530)]
arm: dts: k3-j7200-common-proc-board: Enable CPSW2G port

Enable CPSW2G port to support networking in U-Boot

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
4 years agoARM: dts: k3-j7200-mcu-wakeup: Add CPSW2G support
Vignesh Raghavendra [Thu, 6 Aug 2020 18:57:00 +0000 (00:27 +0530)]
ARM: dts: k3-j7200-mcu-wakeup: Add CPSW2G support

Add MCU NAVSS, UDMA and CPSW2G DT nodes.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
4 years agoARM: dts: k3-j7200: Add HyperBus and HyperFlash nodes
Vignesh Raghavendra [Thu, 6 Aug 2020 18:56:59 +0000 (00:26 +0530)]
ARM: dts: k3-j7200: Add HyperBus and HyperFlash nodes

J7200 SoM has Cypress HyperFlash connected to HyperBus interface, add DT
entries for the same.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
4 years agoARM: dts: k3-j7200: Add wkup gpio node
Vignesh Raghavendra [Thu, 6 Aug 2020 18:56:58 +0000 (00:26 +0530)]
ARM: dts: k3-j7200: Add wkup gpio node

Add wkup_gpio0 node required for detecting whether board mux is set
HyperFlash.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
4 years agoboard: ti: j721e: Add support for HyperFlash detection
Vignesh Raghavendra [Thu, 6 Aug 2020 18:56:57 +0000 (00:26 +0530)]
board: ti: j721e: Add support for HyperFlash detection

On J7200 SoC OSPI0 and HypeFlash are muxed at HW level and only one of
them can be used at any time. J7200 EVM has both HyperFlash and OSPI
flash on board. There is a user switch (SW3.1) that can be toggled to
select OSPI flash vs HyperFlash.
Read the state of this switch via wkup_gpio0_6 line and fixup the DT
nodes to select OSPI0 vs HyperFlash

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
4 years agoarm: dts: k3-j7200: Add USB related DT entries
Vignesh Raghavendra [Thu, 6 Aug 2020 18:56:56 +0000 (00:26 +0530)]
arm: dts: k3-j7200: Add USB related DT entries

Add USB related DT entries to enable USB device mode.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
4 years agoconfigs: j7200_evm_a72: Add Initial support
Lokesh Vutla [Wed, 5 Aug 2020 17:14:31 +0000 (22:44 +0530)]
configs: j7200_evm_a72: Add Initial support

Add initial A72 defconfig support.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
4 years agoconfigs: j7200_evm_r5: Add initial support
Lokesh Vutla [Wed, 5 Aug 2020 17:14:30 +0000 (22:44 +0530)]
configs: j7200_evm_r5: Add initial support

Add initial R5 defconfig support

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
4 years agoarm: dts: k3-j7200: Add R5 specific dts support
Dave Gerlach [Wed, 5 Aug 2020 17:14:29 +0000 (22:44 +0530)]
arm: dts: k3-j7200: Add R5 specific dts support

Add the basic a72 basic dts for j7200. Following nodes were supported:
- UART
- MMC SD
- I2C
- TISCI communication
- LPDDR with 1600MTs configuration.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
4 years agoarm: dts: k3-j7200: Add dts support
Lokesh Vutla [Wed, 5 Aug 2020 17:14:28 +0000 (22:44 +0530)]
arm: dts: k3-j7200: Add dts support

Add the basic a72 dts for j7200. Following nodes were supported:
- UART
- MMC SD
- I2C
- TISCI communication

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agosoc: soc_ti_k3: Add device identification for J7200 SoC
Kishon Vijay Abraham I [Wed, 5 Aug 2020 17:14:27 +0000 (22:44 +0530)]
soc: soc_ti_k3: Add device identification for J7200 SoC

Add device identification for J7200 SoC

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
4 years agoram: k3-j721e: Relax version checks for memory controller
Lokesh Vutla [Wed, 5 Aug 2020 17:14:26 +0000 (22:44 +0530)]
ram: k3-j721e: Relax version checks for memory controller

k3-j721e ddr driver sanity checks for product id and version number.
Version number gets changed for every minor update in the IP. So discard
the version check and just sanity check for product id.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
4 years agoboard: ti: j7200: Add board detection support for j7200
Lokesh Vutla [Wed, 5 Aug 2020 17:14:25 +0000 (22:44 +0530)]
board: ti: j7200: Add board detection support for j7200

Add board detection support for j7200 common processor board.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
4 years agoboard: ti: j7200: Introduce support for j7200 build targets
Lokesh Vutla [Wed, 5 Aug 2020 17:14:24 +0000 (22:44 +0530)]
board: ti: j7200: Introduce support for j7200 build targets

j7200-evm has minor differences with j721e-evm based on the IPs
available in the SoC. Introduce separate build targets for j7200-evm
to incorporate the differences.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
4 years agoarm: mach-k3: j7200: Detect if ROM has already loaded sysfw
Lokesh Vutla [Wed, 5 Aug 2020 17:14:23 +0000 (22:44 +0530)]
arm: mach-k3: j7200: Detect if ROM has already loaded sysfw

Detect if sysfw is already loaded by ROM and pass this information to
sysfw loader. Based on this information sysfw loader either loads the
sysfw image from boot media or just receives the boot notification
message form sysfw.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
4 years agoarm: mach-k3: j7200: Add support for storing extended boot info from ROM
Lokesh Vutla [Wed, 5 Aug 2020 17:14:22 +0000 (22:44 +0530)]
arm: mach-k3: j7200: Add support for storing extended boot info from ROM

Starting J7200 SoC, ROM supports for loading sysfw directly from boot
image. ROM passes this information on number of images that are loaded
to bootloader at certain location. Add support for storing this
information before it gets corrupted.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
4 years agoarm: mach-k3: j7200: Add support for SOC detection
Lokesh Vutla [Wed, 5 Aug 2020 17:14:21 +0000 (22:44 +0530)]
arm: mach-k3: j7200: Add support for SOC detection

The J7200 SoC is a part of the K3 Multicore SoC architecture platform.
It is targeted for automotive gateway, vehicle compute systems,
Vehicle-to-Vehicle (V2V) and Vehicle-to-Everything (V2X) applications.
The SoC aims to meet the complex processing needs of modern embedded
products.

Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, two clusters of lockstep
  capable dual Cortex-R5F MCUs and a Centralized Device Management and
  Security Controller (DMSC).
* Configurable L3 Cache and IO-coherent architecture with high data
  throughput capable distributed DMA architecture under NAVSS.
* Integrated Ethernet switch supporting up to a total of 4 external ports
  in addition to legacy Ethernet switch of up to 2 ports.
* Upto 1 PCIe-GEN3 controller, 1 USB3.0 Dual-role device subsystems,
  20 MCANs, 3 McASP, eMMC and SD, OSPI/HyperBus memory controller, I3C and
  I2C, eCAP/eQEP, eHRPWM among other peripherals.
* One hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
  management.

See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1

Add support for detection J7200 SoC

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
4 years agoarm: mach-k3: j721e: Fix unlocking control module registers
Lokesh Vutla [Wed, 5 Aug 2020 17:14:20 +0000 (22:44 +0530)]
arm: mach-k3: j721e: Fix unlocking control module registers

In main control mmr there is no partition 4 and partition 6 is available
only on J721e. Fix the same in ctrl_mmr_unlock function

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
4 years agoarm: mach-k3: j721e: Add detection for j721e
Lokesh Vutla [Wed, 5 Aug 2020 17:14:19 +0000 (22:44 +0530)]
arm: mach-k3: j721e: Add detection for j721e

Add an api soc_is_j721e(), and use it to enable certain functionality
that is available only on j721e. This detection is needed when DT is not
available.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
4 years agoarm: mach-k3: sysfw-loader: Add support for rom loading sysfw image
Lokesh Vutla [Wed, 5 Aug 2020 17:14:18 +0000 (22:44 +0530)]
arm: mach-k3: sysfw-loader: Add support for rom loading sysfw image

Starting J7200 SoC, ROM supports for loading sysfw directly from boot
image. In such cases, SPL need not load sysfw from boot media, but need
to receive boot notification message from sysfw. So separate out
remoteproc calls for system controller from sysfw loader and just
receive the boot notification if sysfw is already loaded.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
4 years agoarm: mach-k3: Move mmr_unlock to a common location
Lokesh Vutla [Wed, 5 Aug 2020 17:14:17 +0000 (22:44 +0530)]
arm: mach-k3: Move mmr_unlock to a common location

mmr_unlock api is common for all k3 devices. Move it to a common
location.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
4 years agoarm: mach-k3: Fix platform hang when SPL_MULTI_DTB_FIT is not enabled
Jean-Jacques Hiblot [Wed, 5 Aug 2020 17:14:16 +0000 (22:44 +0530)]
arm: mach-k3: Fix platform hang when SPL_MULTI_DTB_FIT is not enabled

If SPL_MULTI_DTB_FIT is not enabled, then CONFIG_SPL_OF_LIST is not defined
And in turn tispl.bin ends up not embedding any DTB.
Fixing it by using CONFIG_DEFAULT_DEVICE_TREE if SPL_OF_LIST is empty.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
4 years agoboard: ti: j721e: Update fdt fixup logic for interconnect nodes
Suman Anna [Wed, 5 Aug 2020 17:14:15 +0000 (22:44 +0530)]
board: ti: j721e: Update fdt fixup logic for interconnect nodes

The DT nodes on J721E SoCs currently use a node name "interconnect" for
the various interconnects. This name is not following the DT schema, and
should simply be "bus". Update the fdt fixup logic to use both the current
and the expected corrected path names so that this logic won't be broken
with newer kernels.

Signed-off-by: Suman Anna <s-anna@ti.com>
4 years agoboard: ti: j721e: Probe eeprom only when CONFIG_TI_I2C_BOARD_DETECT is defined
Lokesh Vutla [Wed, 5 Aug 2020 17:14:14 +0000 (22:44 +0530)]
board: ti: j721e: Probe eeprom only when CONFIG_TI_I2C_BOARD_DETECT is defined

Guard all eeprom probe with TI_I2C_BOARD_DETECT to avoid reading eeprom
when eeprom is not available

Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
4 years agoboard: ti: board_detect: Add stub functions for EEPROM detection apis
Lokesh Vutla [Wed, 5 Aug 2020 17:14:13 +0000 (22:44 +0530)]
board: ti: board_detect: Add stub functions for EEPROM detection apis

Current usage of eeprom apis produce a build failure when
CONFIG_TI_I2C_BOARD_DETECT is not defined. Add stub function for these
apis to avoid build failures.

Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
4 years agoconfigs: Add new config for supporting USB mass storage boot
Faiz Abbas [Mon, 3 Aug 2020 06:05:16 +0000 (11:35 +0530)]
configs: Add new config for supporting USB mass storage boot

Because of space constraints, create a new USB defconfig for R5 to
faciliate booting from USB mass storage devices

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoconfigs: Add defconfig for USB DFU bootmode
Faiz Abbas [Mon, 3 Aug 2020 06:05:15 +0000 (11:35 +0530)]
configs: Add defconfig for USB DFU bootmode

Because of space constraints, create a new USB defconfig for R5 to
faciliate booting in USB peripheral (DFU) bootmode

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoconfigs: am65x_evm_a53: Enable USB Mass storage and DFU boot modes
Faiz Abbas [Mon, 3 Aug 2020 06:05:14 +0000 (11:35 +0530)]
configs: am65x_evm_a53: Enable USB Mass storage and DFU boot modes

Enable configs to facilitate booting from USB Mass Storage devices
as well as USB peripheral boot

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoconfigs: am65x_evm: Add support for DFU related configs
Faiz Abbas [Mon, 3 Aug 2020 06:05:13 +0000 (11:35 +0530)]
configs: am65x_evm: Add support for DFU related configs

Add offset and environment related configs used for booting
from DFU.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoarm: dts: k3-am654-base-board: Add support for USB0 in SPL
Faiz Abbas [Mon, 3 Aug 2020 06:05:12 +0000 (11:35 +0530)]
arm: dts: k3-am654-base-board: Add support for USB0 in SPL

Add nodes for USB0 in SPL to enable USB host boot mode

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoarm: dts: k3-am654-r5-base-board: Add USB0 nodes
Faiz Abbas [Mon, 3 Aug 2020 06:05:11 +0000 (11:35 +0530)]
arm: dts: k3-am654-r5-base-board: Add USB0 nodes

Add USB0 nodes and set them to host mode to support USB host and
peripheral boot modes

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoarm: mach-k3: am6_init: Add support for USB boot mode
Faiz Abbas [Mon, 3 Aug 2020 06:05:10 +0000 (11:35 +0530)]
arm: mach-k3: am6_init: Add support for USB boot mode

Add support for identifying USB host and device boot modes

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoarm: mach-k3: am6_init: Do USB fixups to facilitate host and device boot modes
Faiz Abbas [Mon, 3 Aug 2020 06:05:09 +0000 (11:35 +0530)]
arm: mach-k3: am6_init: Do USB fixups to facilitate host and device boot modes

U-boot only supports either USB host or device mode for a node at a
time in dts. To support both host and dfu bootmodes, set "peripheral"
as the default dr_mode but fixup property to "host" if host bootmode
is detected.

This needs to happen before the dwc3 generic layer binds the usb device
to a host or device driver. Therefore, add an fdtdec_setup_board()
implementation to fixup the dt based on the boot mode.

Also use the same fixup function to set the USB-PCIe Serdes mux to PCIe
in both the host and device cases. This is required for accessing the
interface at USB 2.0 speeds.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoarm: mach-k3: am6_init: Gate mmc related configurations with the appropriate config
Faiz Abbas [Mon, 3 Aug 2020 06:05:08 +0000 (11:35 +0530)]
arm: mach-k3: am6_init: Gate mmc related configurations with the appropriate config

Gate mmc related system related configurations with DM_MMC to avoid build
errors when MMC is not enabled

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoarm: mach-k3: sysfw-loader: Add support to load SYSFW from USB
Faiz Abbas [Mon, 3 Aug 2020 06:05:07 +0000 (11:35 +0530)]
arm: mach-k3: sysfw-loader: Add support to load SYSFW from USB

Add support for loading system firmware from a USB mass storage device

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoarmv7R: K3: am654: Use full malloc in SPL both pre and post reloc
Faiz Abbas [Mon, 3 Aug 2020 06:05:06 +0000 (11:35 +0530)]
armv7R: K3: am654: Use full malloc in SPL both pre and post reloc

In order to be able to use things like file system drivers early on in
SPL (before relocation) in a memory-constrained environment when DDR is
not yet available we cannot use the simple malloc scheme which does not
implement the freeing of previously allocated memory blocks. To address
this issue go ahead and enable the use of the full malloc by manually
initializing the required functionality inside board_init_f by creating
a full malloc pool inside the pre-relocation malloc pool.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agospl: usb: Only init usb once
Faiz Abbas [Mon, 3 Aug 2020 06:05:05 +0000 (11:35 +0530)]
spl: usb: Only init usb once

usb_init() may be called multiple times for fetching multiple images
from SPL. Skip reinitializing USB if its already been done

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agospl: usb: Create an API spl_usb_load()
Faiz Abbas [Mon, 3 Aug 2020 06:05:04 +0000 (11:35 +0530)]
spl: usb: Create an API spl_usb_load()

Create a new API spl_usb_load() that takes the filename as a parameter
instead of taking the default U-boot PAYLOAD_NAME

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoboard: ti: am65x: Update fdt fixup logic for interconnect nodes
Suman Anna [Wed, 29 Jul 2020 18:41:12 +0000 (13:41 -0500)]
board: ti: am65x: Update fdt fixup logic for interconnect nodes

The DT nodes on AM65x SoCs currently use a node name "interconnect" for
the various interconnects. This name is not following the DT schema, and
should simply be "bus". Update the fdt fixup logic to use both the
current and the expected corrected path names so that this logic won't
be broken with newer kernels.

The logic also corrects the crypto node name as the DT node
unit-addresses are all expected to be lower case.

Signed-off-by: Suman Anna <s-anna@ti.com>
4 years agommc: am654_sdhci: Use MMC_MODES_END value instead of hardcoded value
Faiz Abbas [Wed, 29 Jul 2020 01:33:41 +0000 (07:03 +0530)]
mmc: am654_sdhci: Use MMC_MODES_END value instead of hardcoded value

The hardcoded array size leads to array overflows with changes in
speed modes enum in mmc core. Use MMC_MODES_END for otap_del_sel
array declaration to fix this.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
4 years agoarm: dts: k3-j721e: Fix interconnect node names
Suman Anna [Fri, 24 Jul 2020 22:51:40 +0000 (17:51 -0500)]
arm: dts: k3-j721e: Fix interconnect node names

The various CBASS interconnect nodes on K3 J721E SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".

Signed-off-by: Suman Anna <s-anna@ti.com>
4 years agoarm: dts: k3-am65: Fix interconnect node names
Suman Anna [Fri, 24 Jul 2020 22:51:39 +0000 (17:51 -0500)]
arm: dts: k3-am65: Fix interconnect node names

The various CBASS interconnect nodes on K3 AM65x SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".

Signed-off-by: Suman Anna <s-anna@ti.com>
4 years agoARM: omap3: evm: Complete DM_ETH and DM_USB migrations
Derald D. Woods [Sun, 19 Jul 2020 00:23:04 +0000 (19:23 -0500)]
ARM: omap3: evm: Complete DM_ETH and DM_USB migrations

This commit completes the migrations for DM_ETH and DM_USB. The board
is now consistent with omap3_beagle and other remaining OMAP3 boards.

Cc: Tom Rini <trini@konsulko.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
4 years agoMerge tag 'efi-2020-10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Tom Rini [Tue, 11 Aug 2020 12:56:52 +0000 (08:56 -0400)]
Merge tag 'efi-2020-10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi

Pull request for UEFI sub-system for efi-2020-10-rc3

Bugs in the UEFI sub-system are fixed:

* use the optional data of the BootXXXX variables as load options
* simplify function public_key_verify_signature()
* amend a copyright notice

4 years agoarm: mach-k3: Clean non-coherent lines out of L3 cache
Andrew F. Davis [Wed, 15 Jul 2020 21:02:36 +0000 (17:02 -0400)]
arm: mach-k3: Clean non-coherent lines out of L3 cache

When switching on or off the ARM caches some care must be taken to ensure
existing cache line allocations are not left in an inconsistent state.
An example of this is when cache lines are considered non-shared by
and L3 controller even though the lines are shared. To prevent these
and other issues all cache lines should be cleared before enabling
or disabling a coherent master's cache. ARM cores and many L3 controllers
provide a way to efficiently clean out all cache lines to allow for
this, unfortunately there is no such easy way to do this on current K3
MSMC based systems.

We could explicitly clean out every valid external address tracked by
MSMC (all of DRAM), or we could attempt to identify only the set of
addresses accessed by a given boot stage and flush only those
specifically. This patch attempts the latter. We start with cleaning the
SPL load address. More addresses can be added here later as they are
identified.

Note that we perform a flush operation for both the flush and invalidate
operations, this is not a typo. We do this to avoid the situation that
some ARM cores will promote an invalidate to a clean+invalidate, but only
emit the invalidation operation externally, leading to a loss of data.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
4 years agoarm: dts: k3: Add RTI watchdogs
Jan Kiszka [Tue, 23 Jun 2020 11:15:10 +0000 (13:15 +0200)]
arm: dts: k3: Add RTI watchdogs

Add DT entries for main domain watchdog0 and 1 instances on the J721e
well as RTI1-based watchdog on the AM65x. RTI0 does not work for this
purpose on the AM65x, so leave it out.

On AM65x, we mark the power-domain as shared because RTI firmware such
as https://github.com/siemens/k3-rti-wdt may request it as well in order
to prevent accidental shutdown of the watchdog.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
4 years agowatchdog: Add support for K3 RTI watchdog
Jan Kiszka [Tue, 23 Jun 2020 11:15:08 +0000 (13:15 +0200)]
watchdog: Add support for K3 RTI watchdog

This is based on the Linux kernel driver for the RTI watchdog.

To actually reset the system on an AM65x, it requires firmware running
on the R5 that accepts the NMI and issues the actual system reset via
TISCI. Kind of an iTCO, except that this watchdog hardware has support
for no-way-out, and only for that.

On the J721E, reset works without extra firmware help when routing the
RTI interrupt via the ESM.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
4 years agoPrepare v2020.10-rc2
Tom Rini [Mon, 10 Aug 2020 20:10:09 +0000 (16:10 -0400)]
Prepare v2020.10-rc2

Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agoconfigs: Resync with savedefconfig
Tom Rini [Mon, 10 Aug 2020 19:31:07 +0000 (15:31 -0400)]
configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agotest/py: fix SquashFS tests
Joao Marcos Costa [Mon, 10 Aug 2020 12:37:27 +0000 (14:37 +0200)]
test/py: fix SquashFS tests

Use "cons.config.build_dir" instead of writing to the source directory
(read-only). This will fix the test failures in Azure.

Signed-off-by: Joao Marcos Costa <joaomarcos.costa@bootlin.com>
4 years agoefi_loader: set load options in boot manager
Heinrich Schuchardt [Fri, 7 Aug 2020 15:49:39 +0000 (17:49 +0200)]
efi_loader: set load options in boot manager

Up to now we used the value of the bootargs environment variable as load
options in the boot manager. This is not correct. The data has to be taken
from the Boot#### variable.

Let the boot manager copy the optional data of the EFI_LOAD_OPTION as load
options to the loaded image protocol.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
4 years agoefi_loader: factor out efi_set_load_options()
Heinrich Schuchardt [Fri, 7 Aug 2020 15:47:13 +0000 (17:47 +0200)]
efi_loader: factor out efi_set_load_options()

The bootefi bootmgr command has to set the load options for a loaded image
from the value of BootXXXX variable. If the boot manager is not used, the
value is set from the environment variable bootargs (or efi_selftest).

Factor out a common function efi_set_load_options().

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
4 years agoefi_loader: add copyright notice
AKASHI Takahiro [Thu, 30 Jul 2020 07:33:59 +0000 (16:33 +0900)]
efi_loader: add copyright notice

Some amount of code was moved/derived from efi_variable.c regarding
UEFI secure boot, in particluar in the commit 012c56ac76e1 ("efi_loader:
restructure code for TEE variables").
So add the orignal author's copyright notice.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
4 years agolib/crypto: simplify public_key_verify_signature
Heinrich Schuchardt [Sat, 8 Aug 2020 16:57:47 +0000 (18:57 +0200)]
lib/crypto: simplify public_key_verify_signature

The variable region is filled but never used. Remove it.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
4 years agoConvert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig
Tom Rini [Fri, 24 Jul 2020 21:14:47 +0000 (17:14 -0400)]
Convert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig

This converts the following to Kconfig:
   CONFIG_SYS_MMC_ENV_DEV
   CONFIG_SYS_MMC_ENV_PART

Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.

Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agoMakefile: sunxi: Don't use binman to build ATF image
Simon Glass [Fri, 7 Aug 2020 15:44:11 +0000 (09:44 -0600)]
Makefile: sunxi: Don't use binman to build ATF image

At present with sunxi 64-bit, the Makefile builds
u-boot-sunxi-with-spl.bin and then binman overwrites it with its own
version. But the binman definition lacks some parts, in particular
BL31.

For now, work around this with a hack.

Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 42b18df80fd ("x86: Makefile: Drop explicit targets built by binman")
4 years agotest/py: serial# cannot be overwritten on some devices
Heinrich Schuchardt [Fri, 7 Aug 2020 21:11:35 +0000 (23:11 +0200)]
test/py: serial# cannot be overwritten on some devices

On some devices the environment variable serial# cannot be overwritten.
Set the variable only if it is not set.

For our unit test it is sufficient to test if any value for serial-number
is set.

Fixes: 8a5cdf601f8d ("test: efi_selftest: Do not force serial# setting")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
4 years agoMerge branch '2020-08-07-misc-improvements'
Tom Rini [Sat, 8 Aug 2020 12:28:53 +0000 (08:28 -0400)]
Merge branch '2020-08-07-misc-improvements'

- SquashFS support
- Assorted bugfixes

4 years agotest: py: test_shell_run() with CONFIG_HUSH_PARSER=n
Heinrich Schuchardt [Wed, 5 Aug 2020 16:31:42 +0000 (18:31 +0200)]
test: py: test_shell_run() with CONFIG_HUSH_PARSER=n

The hush parser not enabled for some boards, e.g.
sipeed_maix_bitm_defconfig.

With CONFIG_HUSH_PARSER=n a double quotation mark is not interpreted as the
beginning of a string. Use a single quotation mark instead.

Furthermore without the hush parser variables have to be referenced as
${varname}. Add the missing braces.

Reported-by: Sean Anderson <seanga2@gmail.com>
Fixes: 8b86c609b860 ("test/py: add test of basic shell functionality")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
4 years agotests: support mkfs.ext4 without metadata_csum
Stephen Warren [Tue, 4 Aug 2020 17:28:33 +0000 (11:28 -0600)]
tests: support mkfs.ext4 without metadata_csum

Modify various test/py filesystem creation routines to support systems
that don't implement the metadata_csum ext4 feature.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
4 years agoboard: presidio: add LED support
Jway Lin [Wed, 1 Jul 2020 04:08:07 +0000 (21:08 -0700)]
board: presidio: add LED support

Add LED support for Cortina Access Presidio Engineering Board

Signed-off-by: Jway Lin <jway.lin@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CC: Simon Glass <sjg@chromium.org>
4 years agoled: led_cortina: Add CAxxx LED support
Jway Lin [Wed, 1 Jul 2020 04:08:06 +0000 (21:08 -0700)]
led: led_cortina: Add CAxxx LED support

Add Cortina Access LED controller support for CAxxxx SOCs

Signed-off-by: Jway Lin <jway.lin@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Simon Glass <sjg@chromium.org>
Add head file fixed link error and remove unused flashing function
Reviewed-by: Simon Glass <sjg@chromium.org>
4 years agoTravis: Add squashfs-tools
Tom Rini [Fri, 7 Aug 2020 16:33:39 +0000 (12:33 -0400)]
Travis: Add squashfs-tools

So that the tests we now have for squashfs can run, add squashfs-tools
for mksquashfs.

Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agotest/py: Add tests for the SquashFS commands
Joao Marcos Costa [Thu, 30 Jul 2020 13:33:52 +0000 (15:33 +0200)]
test/py: Add tests for the SquashFS commands

Add Python scripts to test 'ls' and 'load' commands. The scripts
generate a SquashFS image and clean the directory after the assertions,
or if an exception is raised.

Signed-off-by: Joao Marcos Costa <joaomarcos.costa@bootlin.com>