board: ti: am62x: evm: Update function calls for splash screen
Use spl_dcache_enable, in place of setup_dram, arch_reserve_mmu to set
up pagetable, initialise DRAM and enable Dcache to avoid multiple
function calls.
Check for CONFIG_SPL_VIDEO in place of CONFIG_SPL_VIDEO_TIDSS to prevent
any build failure in case video config is not defined and video related
functions are called.
Check for CONFIG_SPL_SPLASH_SCREEN and CONFIG_SPL_BMP before calling
splash_display to avoid compilation failure.
arch: arm: mach-k3: common: Return a pointer after setting page table
In spl_dcache_enable after setting up page table, set gd->relocaddr
pointer to tlb_addr, to get next location to reserve memory. Align
tlb_addr with 64KB address.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com> Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
At SPL stage when stack is relocated, the stack pointer needs to be
updated, the stack pointer may point to stack in on chip memory even
though stack is relocated.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
arm: mach-k3: am62a7: change some prints to debug prints
There is little need to print the devstat information or when we exit a
function during a typical boot. Remove them to reduce the noise during
typical operation
ram: k3-ddrss: do not touch ctrl regs during training
During LPDDR initialization we will loop through a series of frequency
changes in order to train at the various operating frequencies. During
this training, accessing the DRAM_CLASS bitfield could happen during a
frequency change and cause the read to hang.
Store the DRAM type into the main structure to avoid multiple readings
while the independent phy is training.
Tom Rini [Mon, 17 Jul 2023 19:26:43 +0000 (15:26 -0400)]
arm: omap2: Fix warning in force_emif_self_refresh
The function declaration for force_emif_self_refresh takes no parameters
but does not specify this, only the prototype in the headers do. As
clang will warn about this, correct it.
arm: mach-k3: am62: Fixup CPU core, gpu and pru nodes in fdt
AM62x SoC is available in multiple variant:
- CPU cores (Cortex-A) AM62x1 (1 core), AM62x2 (2 cores), AM62x4 (4 cores)
- GPU AM625x with GPU, AM623x without GPU
- PRU (Programmable RT unit) can be present or not on AM62x2/AM62x4
Remove the relevant FDT nodes by reading the actual configuration
from the SoC registers, with that change is possible to have a single
dts/dtb file handling the different variant at runtime.
While removing GPU node and CPU nodes also the watchdog node
in the same Module Domain is removed.
A similar approach is implemented for example on i.MX8 and STM32MP1 SoC.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Add register address and relevant bitmasks and shifts.
Allow reading these information:
- device identification
- number of cores (part of device identification)
- features (currently: PRU / no PRU)
- security
- functional safety
- speed grade
- temperature grade
- package
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Andrew Davis <afd@ti.com>
arm: k3: Fix ft_system_setup so it can be enabled on any SoC
ft_system_setup cannot be enabled on SoC without msmc sram otherwise
fdt_fixup_msmc_ram function fails causing system reset.
Fix by moving fdt_fixup_msmc_ram to common_fdt.c file and creating
SoC (AM654, J721E and J721S2) specific files for fdt fixups.
This change was verified to not change anything on any existing board
(all the J721S2, AM654 and J721E boards requires it,
none of the remaining k3 boards require it).
Fixes: 30e96a240156 ("arm: mach-k3: Move MSMC fixup to SoC level") Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
arm: mach-k3: am62a7_init: Open up FSS_DAT_REG3 firewall
On security enforced (HS-SE) devices ROM firewalls OSPI data region3 that
is present in above 64bit region. Open this up in bootloader to allow
Linux to access OSPI flashes in mmap mode.
Without this kernel will crash when accessing this region due to
firewall violations on HS-SE devices.
Nikhil M Jain [Wed, 21 Jun 2023 10:59:53 +0000 (16:29 +0530)]
common: splash_source: Fix type casting errors
During compilation splash_source puts out below warning for type
conversion in splash_load_fit for bmp_load_addr and fit_header.
Change their type to uintptr_t to fix the warnings.
common/splash_source.c: In function ‘splash_load_fit’:
common/splash_source.c:366:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
366 | img_header = (struct legacy_img_hdr *)bmp_load_addr;
| ^
common/splash_source.c:376:49: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
376 | res = splash_storage_read_raw(location, (u32)fit_header, fit_size);
| ^
common/splash_source.c:401:25: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
401 | memmove((void *)bmp_load_addr, internal_splash_data, internal_splash_size);
The above warnings are generated if CONFIG_FIT is enabled.
Nikhil M Jain [Wed, 21 Jun 2023 10:59:52 +0000 (16:29 +0530)]
board: ti: am62x: evm: Include necessary header files
At the time of compilation evm.c gives below warning for implicit
declaration of enable_caches, to mitigate this include cpu_func.h.
board/ti/am62x/evm.c: In function ‘spl_board_init’:
board/ti/am62x/evm.c:90:9: warning: implicit declaration of function ‘enable_caches’ [-Wimplicit-function-declaration]
90 | enable_caches();
Tom Rini [Fri, 21 Jul 2023 14:01:11 +0000 (10:01 -0400)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
For once this adds USB support for two SoCs: the H616 and the F1C100s
series. The rest is support for LPDDR3 DRAM chips on H616 boards.
Gitlab CI passed, and I booted that briefly on an H616 and an F1C200s
board. I don't have an H616 board with LPDDR3 DRAM, but reportedly that
works for Mikhail, and doesn't regress on my DDR3 boards.
clk: zynqmp: Add gem rx and tsu clocks to return register
Add gem_tsu and gem0_rx till gem3_rx to return proper register from
zynqmp_clk_get_register. Otherwise firmware won't be able to set clock
for these due to incorrect register address.
Maksim Kiselev [Wed, 19 Jul 2023 06:53:37 +0000 (09:53 +0300)]
net: axi_emac: Change return value to -EAGAIN if RX is not ready
If there is no incoming package than axiemac_recv will return -1 which
in turn leads to printing `eth_rx: recv() returned error -1` error
message in eth_rx function. But missing a package is not an fatal error,
so return -EAGAIN in that case would be more suitable.
arm64: zynqmp: remove snps, enable_guctl1_resume_quirk quirk for usb
To sync with the upstream code, removed 'snps,enable_guctl1_resume_quirk'
quirk for usb. This quirk is no more available in linux after the xilinx
release 2022.2.
This functionality is taken care of by the 'snps,resume-hs-terminations'
quirk.
Explicitly specify interrupt affinity to avoid HW perfevents
need to guess. This avoids the following error upon linux boot:
armv8-pmu pmu: hw perfevents: no interrupt-affinity property,
guessing.
Linux kernel throws "cacheinfo: Unable to detect cache hierarchy for
CPU 0" warning when booting on zu+ Soc. To fix it add the L2 cache
node and let each CPU point to it.
Michal Simek [Mon, 10 Jul 2023 12:37:36 +0000 (14:37 +0200)]
arm64: zynqmp: Fix usb reset over bootmode pins on zcu100
The commit a4180c369607 ("arm64: zynqmp: Add mode-pin GPIO controller DT
node") added usb phy reset over bootmode pins by default on usb0 only.
zcu100 is using usb0 as peripheral and usb1 as host. Unfortunately reset
line is shared for both usb ulpi phys but usb_rst_b is connected to usb5744
hub which is used only in host mode. Especially this chip requires reset to
operate properly that's why better assign gpio reset to usb1 instead of
usb0.
Without this change usb start crashed when runs.
Michal Simek [Mon, 10 Jul 2023 12:37:35 +0000 (14:37 +0200)]
arm64: zynqmp: Cover K24 revB/1 SOM
Extend compatible versions for K24 SOM.
Changes are not affecting SW behavior that's why all versions are
compatible to each other.
Describing all revisions is done by purpose because user space SW is
reading compatible string for logic around DT overlays and bitstreams.
arm64: zynqmp: Increase reset assert time for TI SGMII PHY
Increase reset assert time for TI SGMII PHY on KR260 CC starting
6.1 kernel. This PHY does not come out of reset with the existing
100us pulse width as per testing on multiple carrier cards. The reset
is driven via a PCA9570 I2C expander. The expander driver was updated
to an upstream version in 6.1 where gpio_chip _set was optimized.
Delays in earlier kernels may have masked this issue. This is a safe
workaround value for assert pulse width before the discussions are
resolved with TI.
arm64: zynqmp: Update MALI 400 interrupt and clock names
Motivation for the commit is to utilize the upstream community
device tree so that the either modified ARM Mali 400 driver
or upstream lima driver can be used.
xilinx: dts: Fix open drain warning on Zynq, ZynqMP and Versal
Fix for below open drain warning on Zynq, ZynqMP and Versal reported by
Linux.
"enforced open drain please flag it properly in DT/ACPI DSDT/board
file."
Add support for Versal NET mini Octal SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Octal SPI
related settings are enabled.
Add support for Versal NET mini Quad SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Quad SPI
related settings are enabled.
cadence_qspi: Enable flash reset for Versal NET platform
Enable flash reset functionality for Versal NET platform.
In cadence_qspi.c there is weak function defined for reset, hence remove
the check for config, so that it will work for Versal and Versal NET
platforms.
Add register defines in Versal NET hardware.h for mini U-Boot flash
reset.
Add read_delay initialization for Versal NET also.
net: zynq_gem: Don't hardcode the MDC clock divisor
As per spec MDC must not exceed 2.5MHz, read the pclk clock
from the device tree and update the MDC clock divisor.
GEM devices support larger clock divisors and have a different
range of divisors. Program the MDIO clock divisors based on
the clock rate of the pclk clock.
Currently xspi0 is used for all spi boot modes, it means it will use "sf
probe 0 0 0" for all spi's irrespective of which node it is wired.
Get boot sequence from dev_seq() and update boot command for xspi
dynamically.
As a result bootcmd for spi is updated as below when two instances of spi
are present in DT node.
bootcmd_xspi0=devnum_xspi=0; run xspi_boot
bootcmd_xspi1=devnum_xspi=1; run xspi_boot
xspi_boot=sf probe $devnum_xspi:0 0 0 && sf read $scriptaddr
$script_offset_f $script_size_f && echo XSPI: Trying to boot script at
${scriptaddr} && source ${scriptaddr}; echo XSPI: SCRIPT FAILED:
continuing...;
Add the missing prototypes for the functions pointed by the below
sparse warnings
warning: no previous prototype for 'set_dfu_alt_info'
[-Wmissing-prototypes]
warning: no previous prototype for 'board_debug_uart_init'
[-Wmissing-prototypes]
mtd: nand: zynq_nand: Change datatype of status and ecc_status to int
status and ecc_status are of unsigned type where they are compared for
negative value. This is pointed by below sparse warning. Change datatype
to int to fix this.
warning: comparison of unsigned expression in '< 0' is always false
[-Wtype-limits]
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com> Link: https://lore.kernel.org/r/20230614090359.10809-5-ashok.reddy.soma@amd.com Signed-off-by: Michal Simek <michal.simek@amd.com>
arm64: zynqmp: Fix the memory node for k26/k24 kria som boards
PMUFW requires top 1MB of the lower DDR memory reserved for its operation,
this is missing in k26/k24 sm static dts files because of which U-Boot
throws warning messages "efi_free_pool: illegal free" as EFI puts
some code to that space which shouldn't happen.
The H616 SoC has support for several types of DRAM: DDR3, LPDDR3,
DDR4 and LPDDR4.
At the moment, the driver only supports DDR3 memory.
Let's extend the driver to support the LPDDR3 memory. All "magic"
values obtained from the boot0.
Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com> Acked-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Wed, 7 Jun 2023 00:07:43 +0000 (01:07 +0100)]
sunxi: H616: dram: split struct dram_para
Currently there is one DRAM parameter struct for the Allwinner H616 DRAM
"driver". It contains many fields that are compile time constants
(set by Kconfig variables), though there are also some fields that are
probed and changed over the runtime of the DRAM initialisation.
Because of this mixture, the compiler cannot properly optimise the code
for size, as it does not consider constant propagation in its full
potential.
Help the compiler out by splitting that structure into two: one that only
contains values known at compile time, and another one where the values
will actually change. The former can then be declared "const", which will
let the compiler fold its values directly into the code using it.
We also add "const" tags for some new "struct dram_config" pointers, to
further increase code optimisation.
To help the compiler optimise the code further, the definition of the
now "const struct dram_para" has to happen at a file-global level, so
move that part out of sunxi_dram_init().
That results in quite some code savings (almost 2KB), and helps to keep
the code small with the LPDDR3 support added later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Andre Przywara [Wed, 7 Jun 2023 00:07:42 +0000 (01:07 +0100)]
sunxi: H616: dram: const-ify DRAM function parameters
There are quite some functions in the Allwinner H616 DRAM "driver", some
of them actually change the parameters in the structure passed to them,
but many are actually not.
To increase the optimisation potential for the code, mark those functions
that just read members of the passed dram_para struct as "const".
This in itself does not decrease the code size, but lays the groundwork
for future changes doing so.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Andre Przywara [Wed, 7 Jun 2023 00:07:41 +0000 (01:07 +0100)]
sunxi: dram: make MBUS configuration functions static
The usage of the C keyword "inline" seems to be a common
misunderstanding: it's a *hint* only, and modern compilers will inline
(or not) functions based on their own judgement and provided compiler
options.
So while marking functions as "inline" does not do much, missing the
"static" keyword will force to compiler to spell out a version of the
function for potential external callers, which actually increases the
code size (though hopefully the linker will drop the function).
Change the "inline" attribute for the mbus_configure_port() functions in
some Allwinner DRAM drivers to "static", so that the explicit version
can actually be dropped from the object file, reducing the code size.
"static inline" has a use case in header files, where it avoids a warning
if a .c file including this header does not use the particular function.
In a .c file itself "static inline" is not useful otherwise, so just use
static here as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Andre Przywara [Sun, 11 Jun 2023 23:32:41 +0000 (00:32 +0100)]
sunxi: H616: enable USB support for H616 boards
Now that the PHY driver supports the H616 USB PHY, we can enable USB
support for the two H616 boards.
As the OrangePi Zero2 has a USB-C port hard-wired to peripheral mode,
let's enable USB gadget mode for port 0, so people can use fastboot,
ethernet or mass storage functionality.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Andre Przywara [Sun, 11 Jun 2023 23:32:39 +0000 (00:32 +0100)]
phy: sun4i-usb: Add H616 USB PHY quirk support
The H616 USB PHY is some kind of special snowflake: Only port2 works out
of the box, but all other ports need some help from this port2 to work
correctly: The CLK_BUS_PHY2 and RST_USB_PHY2 clock and reset need to be
enabled, and the SIDDQ bit in the PMU PHY control register needs to be
cleared. For this register to be accessible, CLK_BUS_ECHI2 needs to be
ungated. Don't ask ....
Follow the respective Linux patch (b45c6d80325b) and add a quirk bit,
triggering the special sequence as outlined above, for PHYs other than
PHY2: ungate this one special clock, and clear the SIDDQ bit. We also
pick the clock and reset from PHY2 and enable them as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Andre Przywara [Sun, 11 Jun 2023 23:32:38 +0000 (00:32 +0100)]
phy: sun4i-usb: Replace types with explicit quirk flags
So far we were assigning some crude "type" (SoC name, really) to each
Allwinner USB PHY model, then guarding certain quirks based on this.
This does not only look weird, but gets more or more cumbersome to
maintain.
Remove the bogus type names altogether, instead introduce flags for each
quirk, and explicitly check for them.
This improves readability, and simplifies future extensions.
Andre Przywara [Sun, 11 Jun 2023 23:32:37 +0000 (00:32 +0100)]
sunxi: Kconfig: rework PHY_USB_SUN4I selection
At the moment we use "select" in each Allwinner SoC's Kconfig section to
include the USB PHY driver in the build. This means it cannot be disabled
via Kconfig, although USB is not really a strictly required core
functionality, and a particular board might not even include USB ports.
Rework the Kconfig part by removing the "select" lines for each SoC's
section, and instead letting it default to "y" in the PHY driver section
itself. We use "depends on !" to exclude the few SoCs we don't support
(yet). The Allwinner V3s does not enable USB (PHY) support at the moment,
even though it should work: let the PHY default to "n" to keep the
current behaviour.
Also the MUSB USB driver directly calls some functions from the PHY
driver, so let the former depend on the PHY driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Tested-by: Sam Edwards <CFSworks@gmail.com>
Andre Przywara [Sun, 11 Jun 2023 23:32:36 +0000 (00:32 +0100)]
phy: sun4i-usb: add Allwinner F1C100s support
The Allwinner F1C100s implements a single USB PHY, connected to its MUSB
OTG controller. The USB PHY is of the simpler, older type (like the A10),
the only real difference is that it's indeed only one PHY.
Add a struct describing those F1C100s USB PHY properties, and connect it
to the new compatible string.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Andre Przywara [Sun, 11 Jun 2023 23:32:35 +0000 (00:32 +0100)]
phy: sun4i-usb: Fix of_xlate() argument check
In its of_xlate() function, the Allwinner USB PHY driver compares the
args_count variable against the number of implemented USB PHYs, although
this is the *number of arguments* to the DT phandle property. Per the DT
binding for this PHY device, this number is always one, so this check
will always fail if the particular SoC implements exactly one USB PHY.
So far this affected only the V3s (which has USB support disabled), but
the F1C100s also sports one PHY only.
Fix that check to compare args_count against exactly 1, and the args[0]
content (requested PHY number) against the number of implemented PHYs.
This fixes USB operation on the Allwinner V3s and allows to enable USB
on the Allwinner F1C100s SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Simon Glass [Tue, 18 Jul 2023 13:24:08 +0000 (07:24 -0600)]
binman: Support writing symbols inside a mkimage image
Add support for writing symbols and determining the assumed position of
binaries inside a mkimage image. This is useful as an example for other
entry types which might want to do the same thing.
Simon Glass [Tue, 18 Jul 2023 13:24:04 +0000 (07:24 -0600)]
binman: Support simple templates
Collections can used to collect the contents of other entries into a
single entry, but they result in a single entry, with the original entries
'left behind' in their old place.
It is useful to be able to specific a set of entries ones and have it used
in multiple images, or parts of an image.
Simon Glass [Tue, 18 Jul 2023 13:23:59 +0000 (07:23 -0600)]
binman: Provide a way to specify the fdt-list directly
Sometimes multiple boards are built with binman and it is useful to
specify a different FDT list for each. At present this is not possible
without providing multiple values of the of-list entryarg (which is not
supported in the U-Boot build system).
Allow a fit,fdt-list-val string-list property to be used instead.
Marek Vasut [Tue, 18 Jul 2023 13:23:58 +0000 (07:23 -0600)]
binman: Convert mkimage to Entry_section
This is needed to handle mkimage with inner section located itself in a
section.
Signed-off-by: Marek Vasut <marex@denx.de>
Use BuildSectionData() instead of ObtainContents(), add tests and a few
other minor fixes: Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 18 Jul 2023 13:23:55 +0000 (07:23 -0600)]
stm32mp15: Avoid writing symbols in SPL
These boards use SPL in a mkimage entry and apparently access the symbol
containing the image position of U-Boot, but put U-Boot in another
image. This means that binman is unable to fill in the symbol correctly
in the SPL binary.
This doesn't matter at present since mkimage doesn't support symbol
writing. But with the upcoming conversion to a section, it will. So add
a property to disable symbol writing.
tools: Fix package discovery in pyproject.toml of u_boot_pylib.
When building from source, setuptools would complain about not finding
package via its auto-discovery mechanism. Manually specify how to
locate the files, relative to the package's directory.
* tools/u_boot_pylib/pyproject.toml: New tool.setuptools.packages.find
section.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
The loads and saves commands crash on the sandbox due to illegal memory
access.
For command line arguments the sandbox uses a virtual address space which
does not equal the addresses of the memory allocated with memmap(). Add the
missing address translations for the loads and saves commands.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sergei Antonov [Mon, 12 Jun 2023 21:19:04 +0000 (00:19 +0300)]
sandbox: fix a compilation error
With sandbox and sandbox64 configurations:
In file included from .../u-boot/include/test/test.h:156,
from .../u-boot/include/test/lib.h:9,
from .../u-boot/test/lib/test_crc8.c:8:
.../u-boot/arch/sandbox/include/asm/test.h: In function ‘sandbox_sdl_set_bpp’:
.../u-boot/arch/sandbox/include/asm/test.h:323:17: error: ‘ENOSYS’ undeclared (first use in this function)
323 | return -ENOSYS;
| ^~~~~~
Per Tom Rini's suggestion:
move that function prototype over to arch/sandbox/include/asm/sdl.h
and make test/dm/video.c include <asm/sdl.h>
Cc: Simon Glass <sjg@chromium.org> Suggested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Sergei Antonov <saproj@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
John Keeping [Thu, 1 Jun 2023 14:11:19 +0000 (15:11 +0100)]
core: read: fix dev_read_addr_size()
The behaviour of dev_read_addr_size() is surprising as it does not
handle #address-cells and #size-cells but instead hardcodes the values
based on sizeof(fdt_addr_t).
This is different from dev_read_addr_size_index() and
dev_read_addr_size_name() both of which do read the cell sizes from the
device tree.
Since dev_read_addr_size() is only used by a single driver and this
driver is broken when CONFIG_FDT_64BIT does not match the address size
in the device tree, fix the function to behave like all of the other
similarly named functions. Drop the property name argument as the only
caller passes "reg" and this is the expected property name matching the
other similarly named functions.
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry Tested-by: Simon Glass <sjg@chromium.org> # chromebook_bob
Eugen Hristev [Thu, 4 May 2023 12:22:21 +0000 (15:22 +0300)]
dm: core: of_access: fix return value in of_property_match_string
of_property_match_string calls of_find_property to search for the
string property.
If the device node does not exist, of_find_property returns NULL, and
of_property_match_string returns -EINVAL, which is correct.
However, if the device node exists, but the property is not found,
of_find_property still returns NULL, but it will place -FDT_ERR_NOTFOUND
in the *lenp variable.
of_property_match_string does not use the lenp parameter, thus this error
case is being lost, and treated as if the node is NULL, and returns
-EINVAL, which is incorrect.
The callers of of_property_match_string treat the error differently if
the return value is -EINVAL or -ENOENT, e.g. in dwc3 driver:
ret = generic_phy_get_by_name(dev, "usb3-phy", &phy);
if (!ret) {
ret = generic_phy_init(&phy);
if (ret)
return ret;
} else if (ret != -ENOENT && ret != -ENODATA) {
debug("could not get phy (err %d)\n", ret);
return ret;
} else {
phy.dev = NULL;
}
So the caller drivers will just consider the property missing if -ENOENT
is returned, versus the case of -EINVAL, which means something else.
To fix this situation, changed the code to call the of_find_property
with the right third argument to catch this error code and treat it
accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Tom Rini [Wed, 12 Jul 2023 02:33:03 +0000 (22:33 -0400)]
CI: Add automatic retry for test.py jobs
It is not uncommon for some of the QEMU-based jobs to fail not because
of a code issue but rather because of a timing issue or similar problem
that is out of our control. Make use of the keywords that Azure and
GitLab provide so that we will automatically re-run these when they fail
2 times. If they fail that often it is likely we have found a real issue
to investigate.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 12 Jul 2023 20:22:22 +0000 (16:22 -0400)]
Azure: Add excludes to the imx8_imx9 job
The job to build all imx8 and imx9 platforms is currently close to, or
sometimes exceeding the allowed build time. Exclude some platforms that
are already being built under their vendor-specific job as well to
reduce the time.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log