Marek Vasut [Sat, 22 Sep 2018 02:13:35 +0000 (04:13 +0200)]
fs: btrfs: Fix cache alignment bugs
The btrfs implementation passes cache-unaligned buffers into the
block layer, which triggers cache alignment problems down in the
block device drivers. Align the buffers to prevent this.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Behun <marek.behun@nic.cz>
Ramon Fried [Fri, 21 Sep 2018 10:35:53 +0000 (13:35 +0300)]
usb: ehci-msm: Add init_after_reset for CI_UDC
MSM uses the chipidea controller IP, however it requires
to reinit the phy after controller reset. in EHCI mode there's a
dedicated callback for it.
In device mode however there's no such callback.
Add implementaion of ci_init_after_reset() to implement the above
requirement in case CI_UDC driver is used.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:52 +0000 (13:35 +0300)]
usb:ci_udc: Introduce init_after_reset phy function
MSM variant of Chipidea must reinitalize the phy
after controller reset.
Introduce ci_init_after_reset() weak function that
can be used to achieve the above init.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:47 +0000 (13:35 +0300)]
phy: db410c: Add MSM USB PHY driver
Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
serial: serial_stm32: Enable uart FIFO for STM32F7xx SoCs
Since commit 7b3b74d32127 ("serial: serial_stm32: Enable overrun")
on STM32F7xx based boards, the first lines of serial output are
missing during boot (we no more see the U-Boot release version,
board model and DRAM size).
By enabling the uart FIFO on STM32F7, the complete U-boot log
can be sent correctly.
Neil Stainton [Wed, 19 Sep 2018 09:38:07 +0000 (10:38 +0100)]
u-boot: align cache flushes in load_elf_image_shdr to line boundaries
Prevent cache warning messages when using the 'bootelf' command on an
Arm target. Round down each section start address and round up the
respective section end to the nearest cache line.
Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
[trini: Manually apply, rework whitespace] Signed-off-by: Tom Rini <trini@konsulko.com>
I tried building using a freshly built Make (4.2.1-69-g8a731d1), but
already the objtool build broke with
orc_dump.c: In function ‘orc_dump’:
orc_dump.c:106:2: error: ‘elf_getshnum’ is deprecated [-Werror=deprecated-declarations]
if (elf_getshdrnum(elf, &nr_sections)) {
Turns out that with that new Make, the backslash was not removed, so cpp
didn't see a #include directive, grep found nothing, and
-DLIBELF_USE_DEPRECATED was wrongly put in CFLAGS.
Now, that new Make behaviour is documented in their NEWS file:
* WARNING: Backward-incompatibility!
Number signs (#) appearing inside a macro reference or function invocation
no longer introduce comments and should not be escaped with backslashes:
thus a call such as:
foo := $(shell echo '#')
is legal. Previously the number sign needed to be escaped, for example:
foo := $(shell echo '\#')
Now this latter will resolve to "\#". If you want to write makefiles
portable to both versions, assign the number sign to a variable:
C := \#
foo := $(shell echo '$C')
This was claimed to be fixed in 3.81, but wasn't, for some reason.
To detect this change search for 'nocomment' in the .FEATURES variable.
This also fixes up the two make-cmd instances to replace # with $(pound)
rather than with \#. There might very well be other places that need
similar fixup in preparation for whatever future Make release contains
the above change, but at least this builds an x86_64 defconfig with the
new make.
clk: Add support for Arm's Versatile Express OSC clock generators
The Arm Versatile Express and Juno development boards contain an
OSC clock generator that can be accessed through the Versatile
Express config bus. The generators are quite often being controlled
by some MCU and the config bus offers a uniform way of exposing them.
Tom Rini [Sat, 29 Sep 2018 15:47:32 +0000 (11:47 -0400)]
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.
Adam Ford [Sun, 9 Sep 2018 21:12:11 +0000 (16:12 -0500)]
ARM: omap3_logic: Remove some manual pin-muxing
With the pinctrl function enabled and the device tree setting up
the pins we want to use, this patch removes the manual pinmuxing
except for that which is not done by the device tree and minimal
pins necessary for SPL (like serial, GPMC, and MMC)
Adam Ford [Sun, 9 Sep 2018 14:21:21 +0000 (09:21 -0500)]
ARM: am3517_evm: Enable TCA6416PW GPIO Expander
With DM_I2C and DM_GPIO working, this patch can enable the
GPIO expander on the I2C bus. This GPIO expander is connected
to some of the DIP switches and can now read the status of these
pins.
Adam Ford [Sun, 9 Sep 2018 12:25:30 +0000 (07:25 -0500)]
ARM: am3517_evm: Enable Pinctrl
The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Adam Ford [Sat, 8 Sep 2018 13:16:23 +0000 (08:16 -0500)]
mmc: omap_mmc: Remove invert references
With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch removes the support for 'invert' from the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO] Signed-off-by: Tom Rini <trini@konsulko.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:52 +0000 (10:35 +0300)]
configs: sama5d4_xplained: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:51 +0000 (10:35 +0300)]
configs: sama5d27_som1_ek: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:50 +0000 (10:35 +0300)]
configs: sama5d2_ptc_ek: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:49 +0000 (10:35 +0300)]
configs: sama5d3_xplained: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:48 +0000 (10:35 +0300)]
configs: sama5d2_xplained: add fdt overlay support
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:42 +0000 (10:35 +0300)]
board: atmel: add support for pda detection
This adds the support for PDA detection as common code for
Atmel boards.
Using the one wire interface over GPIO , an EEPROM memory is read
and compared to preprogrammed values for PDA screens TM4300, TM7000
and TM7000B.
Once the PDA is detected, an environment variable is set accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:41 +0000 (10:35 +0300)]
configs: sama5d4_xplained: add onewire and eeprom drivers
SAMA5D4 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:40 +0000 (10:35 +0300)]
configs: sama5d2_ptc_ek: add onewire and eeprom drivers
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:39 +0000 (10:35 +0300)]
configs: sama5d27_som1_ek: add onewire and eeprom drivers
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:38 +0000 (10:35 +0300)]
configs: sama5d3_xplained: add onewire and eeprom drivers
SAMA5D3 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Tue, 18 Sep 2018 07:35:37 +0000 (10:35 +0300)]
configs: sama5d2_xplained: add onewire and eeprom drivers
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Maxime Ripard [Tue, 18 Sep 2018 07:35:25 +0000 (10:35 +0300)]
w1: Add 1-Wire gpio driver
Add a bus driver for bitbanging a 1-Wire bus over a GPIO.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: fixed some issues] Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Maxime Ripard [Tue, 18 Sep 2018 07:35:24 +0000 (10:35 +0300)]
w1: Add 1-Wire uclass
We might want to use 1-Wire devices connected on boards such as EEPROMs in
U-Boot.
Provide a framework to be able to do that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked] Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This is file system generic loader which can be used to load
the file image from the storage into target such as memory.
The consumer driver would then use this loader to program whatever,
ie. the FPGA device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
doc: Add new doc for file system firmware loader driver model
Provide information about
- overview of file system firmware loader driver model
- describe storage device and partition in device tree source
- describe fie system firmware loader API
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
block: Add a function to find block device descriptor
Add a function to find the block device descriptor of the parent
device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
[trini: Move function declaration to avoid warning] Signed-off-by: Tom Rini <trini@konsulko.com>
cmd: ubifs: Factor out some checking codes into cmd_ubifs_mount()
cmd_ubifs_mount() function would be called directly instead of
involving whole command machinery for mounting ubifs in
generic firmware loader, so some checking codes need to be factored out
into cmd_ubifs_mount() without breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
cmd: ubifs: Move ubifs_initialized checking into cmd_ubifs_umount()
cmd_ubifs_umount() function would be called directly instead of involving
whole command machinery in generic firmware loader, so checking on
ubifs_initialized status need to be done in cmd_ubifs_umount() without
breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix conflicting type error in cmd/ubi.c] Signed-off-by: Tom Rini <trini@konsulko.com>
video: Add support for Arm's Mali Display Processors
Add support for Arm Mali Display Processors DP500, DP550 and DP650.
Only one layer is being used to display the console or boot logo,
even if more layers are supported in the hardware.
ARM: dts: nes: add Nintendo NES/SuperNES Classic Edition support
Note:
- Drop pinctrl from sun8i-r16-nintendo-nes-classic-edition.dts since
sun8i-a23-a33.dtsi is added with Linux sync.
- Don't sync non U-Boot supported dts files
sun8i-a23-ippo-q8h-v1.2.dts
sun8i-a23-ippo-q8h-v5.dts
sun8i-a33-et-q8-v1.6.dts
sun8i-a33-ippo-q8h-v1.2.dts
sun8i-r16-nintendo-nes-classic.dts
sun8i-r16-nintendo-super-nes-classic.dts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Sat, 4 Aug 2018 19:10:10 +0000 (00:40 +0530)]
ARM: dts: sun7i: Update A20 dts(i) files from Linux-v4.18-rc3
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 5d9ef839f874f4e3923c8a9ae7b136c6c3912cd5
Author: Stefan Mavrodiev <stefan@olimex.com>
Date: Wed May 16 14:38:08 2018 +0300
Note:
- Update sun7i-a20-primo73.dts as per Linux, since
this dts is U-Boot specific.
- Drop sun7i-a20-olimex-som-evb-emmc.dts since no board
added for this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The EFI subsystems needs to know the size of the terminal. If the
environment variable
stdout = serial,vidconsole
this size cannot be read from the video console. So the EFI subsystem
sends escape sequences to read the size. With this patch we get support
for the following escape sequences:
ESC "7" Save cursor position
ESC "8" Restore cursor position
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
powerpc: dts: Enable device tree support for T2080QDS
Add device tree for T2080QDS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
powerpc: dts: Add u-boot.dtsi to use binman for MPC85xx boards
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
powerpc: mpc85xx: Use binman to embed dtb inside U-Boot
Below is the sequence to embed dtb inside U-Boot,
1. Remove bootpg and resetvec section if needed
2. Append dtb
3. Append bootpg and resetvec section back if removed in step 1
Above procedure is required only when CONFIG_MPC85xx and
CONFIG_OF_SEPARATE are defined.
Add new config CONFIG_MPC85XX_HAVE_RESET_VECTOR to indicate that
image has resetvec section. Step 1 and step 3 described above are
required only if this config is y.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
binman: Add support for PowerPC mpc85xx 'bootpg + resetvec' entry
This entry contains the PowerPC mpc85xx boot page and resetvec
sections.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>